B1215XD-1W

A_XD-1W & B_XD-1W Series 1W,FIXED INPUT,1000V ISOLATED & UNREGULATED DUAL/SINGLE OUTPUT DC-DC CONVERTER m ulti-country patent protection RoHS FEATURES ● High Efficiency up to 80% ● DIP Package ● 1KVDC Isolation ● Temperature Range: -40°C ~ +85°C ● No Heat sink Required ● No External Component Required ● Internal SMD Construction ● Industry standard pinout ● RoHS Compliance ● Compatible with “DCP01” Series PRODUCT PROGRAM Input Part Number B0505XD-1W B0509XD-1W B0512XD-1W B0515XD-1W A0505XD-1W A0509XD-1W A0512XD-1W A0515XD-1W 5 4.5-5.5 Voltage (VDC) Nominal Range Voltage (VDC) 5 9 12 15 ±5 ±9 ±12 ±15 5 9 12 12 10.8-13.2 15 ±5 ±9 ±12 ±15 5 9 12 24 21.6-26.4 15 ±5 ±9 ±12 ±15 Output Current (mA) Max. 200 111 83 67 ±100 ±56 ±42 ±33 200 111 83 67 ±100 ±56 ±42 ±33 200 111 83 67 ±100 ±56 ±42 ±33 Min. 20 12 9 7 ±10 ±6 ±5 ±4 20 12 9 7 ±10 ±6 ±5 ±4 20 12 9 7 ±10 ±6 ±5 ±4 70 78 78 80 72 77 79 80 71 76 78 79 72 78 79 78 73 78 78 79 73 79 80 80 UL CE UL CE UL CE UL CE UL UL UL UL UL CE UL CE UL CE UL CE UL UL UL UL UL CE UL CE UL CE UL CE UL UL UL UL Efficiency Certificate (%, Typ.) APPLICATIONS The A_XD-1W & B_XD-1W Series are specially designed for applications where a group of polar power supplies are isolated from the input power supply in a distributed power supply system on a circuit board. These products apply to: 1) W here the voltage of the input power supply is fixed (voltage variation ≤ ±10%); 2) W here isolation is necessary between input and output (isolation voltage ≤1000VDC); 3) W here the regulation of the output voltage and the output ripple noise are not demanding. Such as: purely digital circuits, ordinary low frequency analog circuits, and IGBT power device driving circuits. B1205XD-1W B1209XD-1W B1212XD-1W B1215XD-1W A1205XD-1W A1209XD-1W A1212XD-1W A1215XD-1W B2405XD-1W B2409XD-1W B2412XD-1W B2415XD-1W A2405XD-1W A2409XD-1W A2412XD-1W A2415XD-1W Note: The A/B_XD-W 25 series also are available in our company. MODEL SELECTION A 0505XD-1W Rated Power Package Style Output Voltage Input Voltage Produc t Ser ies COMMON SPECIFICATIONS Item Storage humidity range Operating temperature Storage temperature Temp. rise at full load Lead temperature 1.5mm from case for 10 seconds -40 -55 15 Test Conditions Min. Typ. M ax. 95 85 125 25 300 1 Free air convection Plastic(UL94-V0) 3500 2.4 K hours g S °C Units % MORNSUN Science & Technology co.,Ltd. Address: 2th floor 6th building, Hangzhou Industrial District, Guangzhou, China Tel: 86-20-38601850 Fax: 86-20-38601272 http://www.mornsun-power.com Short circuit protection* Cooling Case material MTBF W eight *Supply voltage must be discontinued at the end of short circuit duration. T he copyright and authority for the interpretation of the products are reserved by Mornsun Specifications subject to change without notice. A_XD-1W & B_XD-1W A/1-2009 Page 1 of 3 ISOLATION SPECIFICATIONS I tem Isolation voltage I solation resistance Test conditions Min. Typ. M ax. Units VDC MΩ Tested for 1 minute and 1mA max 1000 Test at 500VDC 1000 TYPICAL CHARACTERISTICS OUTPUT SPECIFICATIONS Item Output power Line regulation For Vin change of 1% 10% to 100% load (5V output) Load regulation 10% to 100% load (9V output) 10% to 100% load (12V output) 10% to 100% load (15V output) Output voltage accuracy Temperature drift Ripple & Noise* Switching frequency 100% full load 20MHz Bandwidth A_XD-1W B_XD-1W 50 75 100 12.8 8.3 6.8 6.3 Test conditions Min 0.1 Typ M ax 1 ±1.2 15 15 15 15 %/°C mVp-p KHz Operating Temp.(oC) Units W % % See tolerance envelope graph 0.03 75 100 Full load, nominal input *Test ripple and noise by “parallel cable” method. See detailed operation instructions at Testing of Power Converter section, application notes. Note: Dual output models unbalanced load: ±5%. APPLICATION NOTE Requirement on output load To ensure this module can operate efficiently and reliably, During operation, the minimum output load is not less than 10% of the full load, and that this product should never be operated under no load! If the actual output power is very small, please connect a resistor with proper resistance at the output end in parallel to increase the load, or use our company’s products with a lower rated output power (A/B_XD-W25 Series). RECOMMENDED CIRCUIT Dual Output L L Vin Cin +Vo Cout DC DC GND Single Output L L Cout 0V -Vo L Vin Cin +Vo Cout DC DC GND 0V Recommended testing and application circuit If you want to further decrease the input/output ripple, an “LC” filtering network may be connected to the input and output ends of the DC/DC converter, see (Figure 1). It should also be noted that the inductance and the frequency of the “LC” filtering network should be staggered with the DC/DC frequency to avoid mutual interference. However, the capacitance of the output filter capacitor must be proper. If the capacitance is too big, a startup problem might arise. For every channel of output, provided the safe and reliable operation is ensured, the greatest capacitance of its filter capacitor sees (Table 1). Single Output Vin GND REG (Figure 1) Dual Output Vin GND REG REG +Vo 0V DC DC REG -Vo REG +Vo DC DC 0V Output Voltage Regulation and Over-voltage Protection Circuit The simplest device for output voltage regulation, over-voltage and over-current protection is a linear voltage regulator with overheat protection that is connected to the input or output end in series (Figure 2). (Figure 2) EXTERNAL CAPACITOR TABLE (Table 1) Cin Single Cout Dual Cout Vin (VDC) (uF) Vout (uF) Vout (uF) (VDC) (VDC) 5 4.7 5 10 ±5 4.7 12 2.2 9 4.7 ±9 2.2 24 1 12 2.2 ±12 1 15 1 ±15 1 It ’s not recommended t o connect any external capacitor in the application field with less than 0.5 w att output. Overload Protection Under normal operating conditions, the output circuit of these products has no protection against overload. The simplest method is to connect a self-recovery fuse in series at the input end or add a circuit breaker to the circuit. No parallel connection or plug and play T he copyright and authority for the interpretation of the products are reserved by Mornsun Specifications subject to change without notice. A_XD-1W & B_XD-1W A/1-2009 Page 2 of 3 OUTLINE DIMENSIONS & PIN CONNECTIONS MECHANICAL DIMENSIONS 20.00 [0.787] RECOMMENDED FOOTPRINT DUAL/SINGLE OUTPUT 10.00 [0.394] 14 8 ∅1.00 [∅0.039] 2.54 [0.100] 1 (Side View) 7.00 [0.276] 2 5 6 7 2.54 [0.100] 0.50 [0.020] 4.10 [0.161] 0.50 [0.020] 5 6 7 8 2.54 [0.100] 1 7.62 [0.300] 14 2 ∅1.00 [∅0.039] 0.30 [0.012] TUBE DUTLINE DIMENSIONS 12.00 [0.472] (Bottom View) 15.24 [0.600] 17.78 [0.700] Note: Unit: mm[inch] Pin section tolerances: ±0.1mm[±0.039inch] General tolerances: ±0.25mm[±0.010inch] FOOTPRINT DETAILS Single Dual Pin Vin Vin 1 2 GND GND 5 0V 0V 6 +Vo +Vo -Vo 7 NC Others NC NC NC: No connection. 8.60 [0.339] 14.70 [0.579] 0.60 [0.024] 5.30 [0.209] Note: Unit: mm[inch] General tolerances: ±0.5mm[±0.020inch] L=530mm[20.866inch] Tube Quantity :25pcs L=220mm[8.661inch] Tube Quantity :10pcs Note: 1. Operation under minimum load will not damage the converter; However, they may not meet all specification listed. 2. All specifications measured at Ta=25 °C, humidity