F0505T-1W

E_T-1W & F_T-1W Series 1W, FIXED INPUT, ISOLATED & UNREGULATED DUAL/SINGLE OUTPUT DC-DC CONVERTER m ulti-country patent protection RoHS FEATURES Small Footprint SMD Package Style 3KVDC Isolation Temperature Range: -40°C to +85°C No Heat sink Required Industry Standard Pinout Internal SMD construction No External Component Required RoHS Compliance PRODUCT PROGRAM Input P art Number F0303T-1W F0305T-1W F0505T-1W F0509T-1W F0512T-1W F0515T-1W E0505T-1W E0509T-1W E0512T-1W 5 4.5-5.5 Voltage (VDC) Nominal 3.3 Range 3.0-3.6 Voltage (VDC) 3.3 5 5 9 12 15 ±5 ±9 ±12 ±15 5 9 12 12 10.8-13.2 15 ±5 ±9 ±12 ±15 Output Current (mA) Max 304 200 200 110 84 66 ±100 ±55 ±42 ±33 200 110 84 66 ±100 ±55 ±42 ±33 Min 30 20 20 11 9 7 ±10 ±6 ±5 ±4 20 11 9 7 ±10 ±6 ±5 ±4 73 75 70 76 78 79 71 77 78 79 69 73 73 74 71 73 74 75 UL UL UL UL UL UL UL UL UL UL UL UL UL UL UL UL Efficiency Certificate (%, Typ.) APPLICATIONS The E_T-1W&F_T-1W Series are specially designed for applications where a group of polar power supplies are isolated from the input power supply in a distributed power supply system on a circuit board. These products apply to: 1) W here the voltage of the input power supply is fixed (voltage variation ≤ ±10%); 2) W here isolation is necessary between input and output (isolation voltage ≤3000VDC); 3) W here the regulation of the output voltage and the output ripple noise are not demanding. Such as: purely digital circuits, ordinary low frequency analog circuits, and IGBT power device driving circuits. E0515T-1W F1205T-1W F1209T-1W F1212T-1W F1215T-1W E1205T-1W E1209T-1W E1212T-1W E1215T-1W Note: The E_T-W2/F_T-W2 series also are available in our company. ISOLATION SPECIFICATIONS Item Isolation voltage Isolation resistance Test Conditions Tested for 1 minute and 1mA max Test at 500VDC Min 3000 1000 Typ Max Units VDC MΩ OUTPUT SPECIFICATIONS Item Output power Test Conditions For Vin change of 1%(3.3V output) For Vin change of 1%(Others output) 10% to 100% load 3.3V output 15 12.8 8.3 6.8 6.3 10% to 100% load 5V output Load regulation 10% to 100% load 9V output 10% to 100% load 12V output 10% to 100% load 15V output Output voltage accuracy Temperature drift Output ripple &Noise* 100% full load 20MHz Bandwidth E_T-1W series F_T-1W series 50 75 100 Min 0.1 Typ. Max 1 ±1.5 ±1.2 20 15 10 10 10 0.03 75 100 % /°C mVp-p KHz % Units W MODEL SELECTION Rated Power Package Style Output Voltage Input Voltage Product Series Line regulation See tolerance envelope graph MORNSUN Science& Technology co.,Ltd. Address: 2th floor 6th building, Huangzhou Industrial District, Guangzhou, China Tel: 86-20-38601850 Fax:86-20-38601272 Http://www.mornsun-power.com Switching frequency Full load, nominal input *Test ripple and noise by “parallel cable” method. See detailed operation instructions at Testing of Power Converter section, application notes. Note: 1. All specifications measured at TA=25°C, humidity220 oC ) 2 6 0o C 1 0 Sec Max 2 2 0o C Vin (VDC) 3 .3/5 12 - Cin ( uF) 4.7 2.2 - Single Vout ( VDC) 5 9 12 15 Cout (uF) 10 4.7 2.2 1 Dual Vout (VDC) ±3.3/5 ±9 ±12 ±15 Cout ( uF) 4.7 2.2 1 1 OUTLINE DIMENSIONS & FOOTPRINT DETAILS First Angle Projection RECOMMENDED FOOTPRINT Top view,grid:2.54*2.54mm(0.1*01inch) 7.50 (0.295) 11.20 (0.441) 1211 10 87 Top View Sigle/Dual output It ’s not recommended to connect any external capacitor in t he application field with less than 0.5 watt output. Output Voltage Regulation and Over- voltage Protection Circuit The simplest device for output voltage regulation, over-voltage and over-current protection is a linear voltage regulator with overheat protection that is connected to the i nput or output end in series (Figure2). Dual O u tput Vi n GND R EG REG 2.00 (0.079) 8 7 2.54 (0.100) 0.60 (0.024) 12 11 10 +Vout 0V DC DC REG -Vout 6.50 (0.254) 6.25 (0.244) Side View 4.25 (0.166) FOOTPRINT DETAILS Pin 1 2 Single GND Vin 0V (0.039) Single O utput Vi n R EG REG +Vout 1.30 Dual GND Vin 0V -Vo +Vo NC GND DC DC 0V (Figure2) Overload Protection Under normal operating conditions, the output circuit of t hese products has no protection against overload. The simplest method is to connect a self-recovery fuse in series at the input end or add a circuit breaker to the circuit. No parallel connection or plug and play. NC 8 +Vo Others NC NC:No Connection Note: Unit:mm(inch) Pin section:0.50*0.30mm(0.020*0.012inch) Pin section tolerances: 0.10mm( 0.004inch) General tolerances: 0.15mm( 0.006inch) MORNSUN reserves the copyright Specifications subject to change without notice. F_T-1W &E_T-1W A/1-2008 Page 2 of 2