IB1512LS-1W

IB_LD-1W & IB_LS-1W Series 1W, FIXED INPUT, ISOLATED & REGULATED SINGLE OUTPUT DC-DC CONVERTER m ulti-country patent protection FEATURES Small Footprint SIP/DIP Package Low Ripple and good EMC features Temperature Range: -40°C to +85°C No Heat Sink Required No External Component Required 1KVDC Isolation Internal SMD construction Continuous Short Circuit Protection Industry Standard Pinout RoHS Compliance RoHS PRODUCT PROGRAM Input P art Number IB0505LD-W75 IB0509LD-1W IB0512LD-1W IB0515LD-1W IB0505LS-W75 IB0509LS-1W IB0512LS-1W IB0515LS-1W IB1205LD-W75 IB1209LD-1W IB1212LD-1W 5 4.75-5.25 Voltage (VDC) Nominal Range Output Voltage Current (mA) (VDC) M ax Min 5 9 12 15 5 9 12 15 5 9 12 12 11.4-12.6 15 5 9 12 15 5 15 14.25-15.75 Efficiency P ackage (%, Typ) 68 70 71 73 68 70 71 73 68 72 70 74 68 72 70 74 70 71 71 72 68 68 73 75 68 68 73 75 DIP DIP DIP DIP SIP SIP SIP SIP DIP DIP DIP DIP SIP SIP SIP SIP SIP SIP SIP SIP DIP DIP DIP DIP SIP SIP SIP SIP 150 111 83 67 150 111 83 67 150 111 83 67 150 111 83 67 150 111 83 67 150 111 83 67 150 111 83 67 15 12 9 7 15 12 9 7 15 12 9 7 15 12 9 7 15 12 9 7 15 12 9 7 15 12 9 7 APPLICATIONS The IB_LD-1W & IB_LS-1W Series are specially designed for applications where a single power supply is highly isolated from the input power supply in a distributed power supply system on a circuit board. These products apply to: 1) Where the voltage of the input power supply is fixed (voltage variation ≤± 5%); 2) Where isolation is necessary between input and output (isolation voltage ≤1000VDC); 3) Where the regulation of the output voltage and the output ripple and noise are demanded. IB1215LD-1W IB1205LS-W75 IB1209LS-1W IB1212LS-1W IB1215LS-1W IB1505LS-W75 IB1509LS-1W * IB1512LS-1W * IB1515LS-1W IB2405LD-W75* IB2409LD-1W IB2412LD-1W IB2415LD-1W IB2405LS-W75 IB2409LS-1W IB2412LS-1W IB2415LS-1W 9 12 15 5 9 12 15 5 9 12 15 24 22.8-25.2 MODEL SELECTION Rated Power Package Style Output Voltage Input Voltage P roduct Series * Designing. COMMON SPECIFICATION Item Storage humidity Operating temperature Storage temperature Temp. rise at full load Lead temperature Short circuit protection 1.5mm from case for 10 seconds -40 -55 15 Test condition Min Typ Max 95 85 125 25 300 Continuous Free air convection Plastic(UL94-V0) 3500 2.1 K hours g °C Units % MORNSUN Science& Technology co.,Ltd. Address: 2th floor 6th building, Hangzhou Industrial District, Guangzhou, China Tel: 86-20-38601850 Fax: 86-20-38601272 http://www.mornsun-power.com Cooling Case material MTBF W eight MORNSUN reserves the copyright Specifications subject to change without notice. IB_LD-1W & IB_LS-1W A/2-2008 Page 1 of 2 ISOLATION SPECIFICATIONS Item Isolation voltage Isolation resistance Test condition Tested for 1 minute Test at 500VDC Min 1000 1000 Typ Max Units VDC MΩ APPLICATION NOTE Requirement on output load To ensure this module can operate efficiently and reliably, During operation, the minimum output load is not less than 10% of the full load, and that Min 0.1 Typ Max 1 ±0.25 ±1 ±3 0.03 10 50 100 20 75 %/°C mVp-p KHz % Units W this product should never be OUTPUT SPECIFICATIONS Item Output power Line regulation L oad regulation Output voltage accuracy Temperature drift Ripple* Noise* Switching frequency For Vin change of 5% 10% to 100% load 100% full load 100% full load 20MHz Bandwidth 20MHz Bandwidth Full load, nominal input Test Conditions operated under no load! If the actual output p ower is very small, please connect a resistor with proper resistance at the output end in p arallel to increase the load, or use our company’s products with a lower rated output p ower (IB_LD -W25/IB_LS-W25 series). Recommended circuit I f you want to further decrease the input/output ripple, an “LC” filtering network may b e connected to the input and output ends of the DC/DC converter, see (Figure 1). L L *Test ripple and noise by “parallel cable” method. See detailed operation instructions at Testing of Power Converter section, application notes. Note: 1. All specifications measured at TA=25°C, humidity