RSB2412T-3W

RSB_T-3W Series WIDE INPUT ISOLATED & REGULATED 3W SINGLE OUTPUT SMD PACKAGE multi-country patent protection RoHS FEATURES ● Wide (2:1) Input Range ● Operating Temperature:-40°C~+85°C ● 1500VDC Isolation ● UL94-V0 Package ● No Heat Sink Required ● Industry Standard Pinout ● MTBF>1,000,000 hours ● Custom Service Available ● RoHS Compliance PRODUCT PROGRAM Part Number Nominal RSB1205T-3W RSB1209T-3W RSB1212T-3W RSB1215T-3W RSB2405T-3W RSB2409T-3W RSB2412T-3W RSB2415T-3W RSB4803T-3W RSB4805T-3W RSB4809T-3W RSB4812T-3W RSB4815T-3W 48 36~72 80 24 18~36 40 12 9~18 22 Input Voltage (VDC) Range Max* Voltage (VDC) 5 9 12 15 5 9 12 15 3.3 5 9 12 15 Output Current(mA) Max 600 330 250 200 600 330 250 200 909 600 330 250 200 Min 60 33 25 20 60 33 25 20 90 60 33 25 20 75 78 79 78 77 80 82 81 72 75 78 81 83 Efficiency (%, Typ) APPLICATIONS The RSB_T-3W Series are specially designed for applications where a wide range input voltage power supplies are isolated from the input power supply in a distributed power supply system on a circuit board. These products apply to: 1) Where the voltage of the input power supply is wide range (voltage range: 2:1); 2) Where isolation is necessary between input and output (isolation voltage =1500VDC); 3) Where the regulation of the output voltage and the output ripple noise are demanded. ISOLATION SPECIFICATIONS Item Isolation voltage Isolation resistance Test conditions Flash tested for 60 seconds Test at 500VDC Min 1500 1000 Typ Max Units VDC MΩ MODEL SELECTION RSB2405T-3W Rated Power Package Style Output Voltage Input Voltage Product Series OUTPUT SPECIFICATIONS Item 3W output power Output Voltage accuracy Load regulation Line regulation Temperature drift (Vout) Ripple Noise Switching frequency Test conditions See below products program Refer to recommended circuit From 10% to 100% load Input Voltage From Low to High Refer to recommended circuit 20MHz bandwidth 20MHz bandwidth 100% load, nominal input voltage Min 0.3 Max 3 ±1 ±2 ±0.5 ±0.75 ±0.2 ±0.5 ±0.03 50 50 100 300（PFM） Typ Units W % %/°C mVp-p KHz MORNSUN Science& Technology Ltd. Address: 2th floor 6th building, Huangzhou Industrial District, Guangzhou, China Tel: 86-20-38601850 Fax: 86-20-38601272 Http://www.mornsun-power.com Note: 1.All specifications measured at TA=25°C, humidity1,000,000 hours Recommended Circuit All the RSB_T-3W Series have been tested according to the following recommended testing circuit before leaving factory. This series should be tested under load(Figure 1). Vin Cin Vout DC DC 0V GND If you want to further decrease the input/output ripple, you can increase capacitance properly or choose capacitors with low ESR. However, the capacitance should not be too high(Table 1) Extemal Capacitor Table(Table 1) Vout 5V 9V 12V 15V 3.3μF Cout/μF（max） 1000 680 470 220 2200 TYPICAL CHARECTERISTICS Temperature Derating Graph External Capacitor Operating Temp.( C ) FOOTPRINT DETAILS Top View Pin 23,24 1,2 13 15 Others Although this series of DC/DC converter can work without external capacitor, in order to keep an optimum performance, however, it needs external capacitor. (Table 2) External Capacitor Table (Table 2) Vin F unction Vin GND +Vo 0V NC Cin 100uF 10uF 12V 24V&48V Cout (0+70°C) 100uF (electrolytic capacitor) Cout (-40+85°C) 47uF (tantalum capacitor) Input Current When it is used in unregulated power supply, be sure that the fluctuating range of the power supply and the rippled voltage do not exceed the module standard. Input current of power supply should afford the startup current of this kind of DC/DC module (Figure 2) Input Current(A) OUTLINE DIMENSIONS (1.27) 10.5 15 14 13 16.1(0.63) (0.74) 24 23 22 Ip 123 10 1112 18.8 14.4 2.18 (0.085) 17.78 (0.7) 0.5 (0.02) 0.27 Input Voltage Range Input Voltage (V) (Top View) (Side View) Note: Unit: mm(inch); Tolerance: ±0.25mm; All Pins on a 2.54mm pitch; APPLICATION NOTE Requirement on Output Load To ensure this module operate efficiently and reliably, a minimum load is specified for this kind of DC/DC converter in addition to a maximum load (namely full load). During operation, make sure the specified range of input voltage is not exceeded, the minimum out put load is not less than 10% Of the full load, If the actual load is less below the specified minimum load, the output ripple of this type of DC/DC converter may increase drastically. If the actual output power from the load in your circuit is very small, please connect a resistor with proper resistance at the output end to in parallel to increase the load, or use our company’s other products with a lower rated output power. The products cannot be used in parallel and in plug and play. MORNSUN reserves the copyright For any design change and upgrade, we will not make any prior notification A/1-2007 Page 2 of 2