UFA4812MP-6W

UFA_MP-6W & UFB_MP-6W Series 6W, WIDE INPUT, ISOLATED & REGULATED DUAL & SINGLE OUTPUT, DC-DC CONVERTER multi-country patent protection F EATURES Efficiency up to 86% Wide (4:1) Input Range 1.5KVDC Input/Output Isolation Continuous Short Circuit Protection Operating Temperature: -40°C to +85°C Internal SMD construction Metal Shielding Package No Heat Sink Required Industry Standard Pinout MTBF>1,000,000 hours RoHS Compliance RoHS PRODUCT PROGRAM I nput P art Number UFA2405MP-6W UFA 2412MP-6W UFA 2415MP-6W UFA 2424MP-6W UFB2403MP-6W UFB2405MP-6W UFB2412MP-6W UFB2415MP-6W UFB2424MP-6W UFA4805MP-6W * 24 9-36 40 Voltage (VDC) Nominal Range M ax** Voltage (VDC) ±5 ±12 ±15 ±24 3.3 5 12 15 24 ±5 ±12 ±15 ±24 48 18-75 80 3.3 5 12 15 24 Output Current (mA) Max ±600 ±250 ±200 ±125 1500 1200 500 400 250 ±600 ±250 ±200 ±125 1500 1200 500 400 250 Min ±60 ±25 ±20 ±13 150 120 50 40 25 ±60 ±25 ±20 ±13 150 120 50 40 25 80 80 82 85 78 80 82 82 83 80 82 84 85 76 80 84 85 86 Efficiency (%, Typ) APPLICATIONS The UFA_MP-6W & UFB_MP-6W Series are specially designed for applications where a wide range input voltage power supplies are isolated from the input power supply in a distributed power supply system on a circuit board. These products apply to: 1) Where the voltage of the input power supply is wide range (voltage range≤4:1); 2) Where isolation is necessary between input and output(Isolation Voltage≤ 1500VDC); 3) Where the regulation of the output voltage and the output ripple noise are demanded. UFA4812MP-6W UFA4815MP-6W UFA4824MP-6W UFB4803MP-6W * UFB4805MP-6W UFB4812MP-6W UFB4815MP-6W UFB4824MP-6W * Designing. * * Input voltage can’t exceed this value, or will cause the permanent damage. Note: The load shouldn't be less than 10%, otherwise ripple will increase dramatically. Operation under 10% load will not damage the converter; However, they may not meet all specification listed. MODEL SELECTION UFA2405MP-6W Rated Power Package Styl e Output Voltage Input Voltage Product Ser ies OUTPUT SPECIFICATIONS Item Output Power Test Conditions See below products program ±0.2 ±0.5 ±1 ±3 0.02 30 100 300 50 300 KHz Min Typ Max 6 ±0.5 ±2* ±3 ±5 %/°C m Vp-p % Units W Line Regulation(at full load) I nput voltage from low to high Load Regulation Positive Voltage Accuracy From 10% To 100% load Refer to recommended circuit Negative Voltage Accuracy Refer to recommended circuit Temperature Drift(Vout) M ORNSUN Science& Technology co.,Ltd. Address: 2th floor 6th building, Huangzhou I ndustrial District, Guangzhou, China Tel: 86-20-38601850 Fax: 86-20-38601272 Http://www.mornsun-power.com Ripple** Noise** Switching Frequency Refer to recommended circuit 20MHz bandwidth 20MHz bandwidth 100% load, nominal Input voltage * Dual output models unbalanced load: ±5%. **Test ripple and noise by “parallel cable” method. See detailed operation instructions at Testing of Power Converter section, application notes. MORNSUN reserves the copyright Specifications subject to change without notice. UFA_MP-6W & UFB_MP-6W A/2-2008 Page 1 of 2 COMMON SPECIFICATION Item Storage humidity Operating temperature Storage temperature Temp. rise at full load Lead temperature Isolation voltage Isolation resistance Cooling Short circuit protection Case material MTBF W eight 1.5mm from case for 10 seconds Tested for 1 minute and 1mA max Test at 500VDC 1500 1000 Free air convection Continuous, automatic recovery Copper, Nickel Plated 1000 17 K hours g -40 -55 40 300 VDC MΩ Test Conditions Min Typ Max 95 85 125 °C Units % APPLICATION NOTE Recommended Circuit All the UFA_MP-6W & UFB_MP-6W Series have been tested according to the following recommended testing circuit before leaving factory. This series should be tested under load. Never be tested under no load (see Figure 1). Dual Output Vin Ci n +Vout DC DC 0V -Vout GND Single Output Vin Cin +Vout DC DC 0V GND Note: 1. All specifications measured at TA=25° C, humidity