VFB1205MP-6W

VFA_MP-6W & VFB_MP-6W Series 6W, WIDE INPUT, DUAL & SINGLE OUTPUT DIP PACKAGE DC-DC CONVERTER m ulti-country patent protection FEATURES Efficiency up to 85% Wide (2:1) Input Range 1.5KVDC Input/Output Isolation Continuous Short Circuit Protection Operating Temperature: -40°C to +85°C Internal SMD construction Metal Shielding Package No Heat Sink Required Industry Standard Pinout MTBF>1,000,000 hours RoHS Compliance RoHS PRODUCT PROGRAM I nput Part Number VFA1205MP-6W VFA1212MP-6W VFA1215MP-6W VFA1224MP-6W VFB1203MP-6W VFB1205MP-6W VFB1212MP-6W VFB1215MP-6W VFB1224MP-6W VFA2405MP-6W VFA2412MP-6W 12 9-18 20 Voltage (VDC) Nominal Range Max* Voltage (VDC) ±5 ±12 ±15 ±24 3.3 5 12 15 24 ±5 ±12 ±15 ±24 24 18-36 40 3.3 5 12 15 24 ±5 ±12 ±15 ±24 48 36-75 80 3.3 5 12 15 24 Output Current (mA) Max ±600 ±250 ±200 ±125 1500 1200 500 400 250 ±600 ±250 ±200 ±125 1500 1200 500 400 250 ±600 ±250 ±200 ±125 1500 1200 500 400 250 Min ±60 ±25 ±20 ±13 150 120 50 40 25 ±60 ±25 ±20 ±13 150 120 50 40 25 ±60 ±25 ±20 ±13 150 120 50 40 25 79 80 80 82 78 78 82 82 84 78 82 82 84 76 80 83 83 85 80 83 84 85 79 81 82 84 85 Efficiency (%, Typ) APPLICATIONS The VFA_MP-6W & VFB_MP-6W Series are specially designed for applications where a wide range input voltage power supplies are isolated from the input power supply in a distributed power supply system on a circuit board. These products apply to: 1) Where the voltage of the input power supply is wide range (voltage range≤ 2:1); 2) Where isolation is necessary between input and output(Isolation Voltage≤ 1500VDC); 3) Where the regulation of the output voltage and the output ripple noise are demanded. VFA2415MP-6W VFA2424MP-6W VFB2403MP-6W VFB2405MP-6W VFB2412MP-6W VFB2415MP-6W VFB2424MP-6W VFA4805MP-6W VFA4812MP-6W VFA4815MP-6W VFA4824MP-6W VFB4803MP-6W VFB4805MP-6W VFB4812MP-6W VFB4815MP-6W VFB4824MP-6W MODEL SELECTION VFA1215MP-6W Rated Power Package Styl e Output Voltage Input Voltage Product Series * Input voltage can’t exceed this value, or will cause the permanent damage. Note:The load shouldn't be less than 10%,otherwise ripple will increase dramatically. Operation under 10% load will not damage the converter; However, they may not meet all specification listed. OUTPUT SPECIFICATIONS Item Output Power Load Regulation Positive Voltage Accuracy Test Conditions See below products program ±0.2 ±0.5 ±1 ±3 0.02 30 100 300 50 300 From 10% To 100% load Refer to recommended circuit Refer to recommended circuit Refer to recommended circuit 20MHz bandwidth 20MHz bandwidth 100% load, nominal input voltage Min Typ M ax 6 ±0.5 ±2* ±3 ±5 %/ °C m Vp-p KHz % Units W Line Regulation(at full load) Input voltage from low to high MORNSUN Science& Technology co.,Ltd. Address: 2th floor 6th building, Huangzhou Industrial District, Guangzhou, China Tel: 86-20-38601850 Fax: 86-20-38601272 Http://www.mornsun-power.com Negative Voltage Accuracy Temperature Drift(Vout) Ripple** Noise** Switching Frequency *Dual output models unbalanced load: ±5%. **Test ripple and noise by “parallel cable” m ethod. See detailed operation instructions at Testing of Power Converter section, application notes. MORNSUN reserves the copyright Specifications subject to change without notice. VFA_MP-6W & VFB_MP-6W A/2-2008 Page 1 of 2 COMMON SPECIFICATION I tem Storage humidity Operating temperature Storage temperature Lead temperature Temp. rise at full load I solation voltage I solation resistance Cooling Short circuit protection Case material MTBF W eight Tested for 1 minute and 1 mA max Test at 500VDC 1500 1000 Free air convection Continuous, automatic recovery Copper, Nickel Plated 1000 17 K hours g 1.5mm from case for 10 seconds 40 VDC MΩ -40 -55 Test Conditions Min Typ Max 95 85 125 300 °C Units % APPLICATION NOTE Recommended Circuit All the VFA_MP-6W & VFB_MP- 6W Series have been tested according t esting to the before following leaving r ecommended circuit f actory. This series should be tested under load. Never be tested under no load (see Figure 1). Dual Output Vin Ci n +Vout DC DC 0V -Vout GND Single Output Vin Cin +Vout Note: 1. All specifications measured at TA=25° C, humidity