SN54LS113A

SN54/74LS113A DUAL JK NEGATIVE EDGE-TRIGGERED FLIP-FLOP The SN54 / 74LS113A offers individual J, K, set, and clock inputs. These monolithic dual flip-flops are designed so that when the clock goes HIGH, the inputs are enabled and data will be accepted. The logic level of the J and K inputs may be allowed to change when the clock pulse is HIGH and the bistable will perform according to the truth table as long as minimum setup times are observed. Input data is transferred to the outputs on the negative-going edge of the clock pulse. DUAL JK NEGATIVE EDGE-TRIGGERED FLIP-FLOP LOW POWER SCHOTTKY LOGIC DIAGRAM (Each Flip-Flop) J SUFFIX CERAMIC CASE 632-08 14 1 Q 5(9) 6(8) Q SET (SD) 4(10) J 3(11) 1(13) CLOCK (CP) K 2(12) 14 1 N SUFFIX PLASTIC CASE 646-06 14 1 D SUFFIX SOIC CASE 751A-02 ORDERING INFORMATION MODE SELECT — TRUTH TABLE INPUTS OPERATING MODE SD Set Toggle Load “0” (Reset) Load “1” (Set) Hold L H H H H J X h l h l K X h h l l Q H q L H q Q L q H L q 3 J CP OUTPUTS SN54LSXXXJ SN74LSXXXN SN74LSXXXD Ceramic Plastic SOIC LOGIC SYMBOL 4 10 H, h = HIGH Voltage Level L, I = LOW Voltage Level X = Don’t Care l, h (q) = Lower case letters indicate the state of the referenced input (or output) l, h (q) = one set-up time prior to the HIGH to LOW clock transition. SD Q 5 11 J SD Q 9 1 2 13 Q 6 12 CP Q 8 K K VCC = PIN 14 GND = PIN 7 FAST AND LS TTL DATA 5-189 SN54/74LS113A GUARANTEED OPERATING RANGES Symbol VCC TA IOH IOL Supply Voltage Operating Ambient Temperature Range Output Current — High Output Current — Low Parameter 54 74 54 74 54, 74 54 74 Min 4.5 4.75 – 55 0 Typ 5.0 5.0 25 25 Max 5.5 5.25 125 70 – 0.4 4.0 8.0 Unit V °C mA mA DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified) Limits Symbol VIH VIL VIK VOH Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Voltage 54 74 54, 74 VOL Output LOW Voltage 74 J, K Set Clock IIH Input HIGH Current J, K Set Clock J, K Set, Clock – 20 0.35 0.5 20 60 80 0.1 0.3 0.4 – 0.4 – 0.8 – 100 6.0 V µA 2.5 2.7 54 74 – 0.65 3.5 3.5 0.25 0.4 Min 2.0 0.7 0.8 – 1.5 V V V V Typ Max Unit V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = – 18 mA VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table IOL = 4.0 mA IOL = 8.0 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table VCC = MAX, VIN = 2.7 V mA VCC = MAX, VIN = 7.0 V IIL IOS ICC Input LOW Current mA mA mA VCC = MAX, VIN = 0.4 V VCC = MAX VCC = MAX Short Circuit Current (Note 1) Power Supply Current Note 1: Not more than one output should be shorted at a time, nor for more than 1 second. AC CHARACTERISTICS (TA = 25°C, VCC = 5.0 V) Limits Symbol fMAX tPLH tPHL Parameter Maximum Clock Frequency Propagation Delay, Clock Set to Output Min 30 Typ 45 15 15 20 20 Max Unit MHz ns ns VCC = 5.0 V CL = 15 pF Test Conditions AC SETUP REQUIREMENTS (TA = 25°C, VCC = 5.0 V) Limits Symbol tW tW ts th Parameter Clock Pulse Width High Set Pulse Width Setup Time Hold Time Min 20 25 20 0 Typ Max Unit ns ns ns ns VCC = 5.0 V Test Conditions FAST AND LS TTL DATA 5-190 Case 751A-02 D Suffix 14-Pin Plastic SO-14 -A14 8 NOTES: 1. DIMENSIONS A" AND B" ARE DATUMS AND T" IS A DATUM SURFACE. 2. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 3. 4. CONTROLLING DIMENSION: MILLIMETER. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 5. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 6. 751A 01 IS OBSOLETE, NEW STANDARD 751A 02. -B1 7 P 7 PL 0.25 (0.010) M B M G C SEATING PLANE R X 45° D 14 PL 0.25 (0.010) M K T B S M F J A S DIM A B C D F G J K M P R MILLIMETERS MIN MAX 8.55 3.80 1.35 0.35 0.40 8.75 4.00 1.75 0.49 1.25 INCHES MIN MAX 0.337 0.150 0.054 0.014 0.016 0.344 0.157 0.068 0.019 0.049 1.27 BSC 0.19 0.10 0 0.25 0.25 7 0.050 BSC 0.008 0.004 0 0.009 0.009 7 ° ° ° ° 5.80 0.25 6.20 0.50 0.229 0.010 0.244 0.019 Case 632-08 J Suffix 14-Pin Ceramic Dual In-Line -A14 8 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. -B1 7 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIM F MAY NARROW TO 0.76 (0.030) WHERE THE LEAD ENTERS THE CERAMIC BODY. 5. 632 01 THRU 07 OBSOLETE, NEW STANDARD C L 632 08. -TSEATING PLANE K F D 14 PL 0.25 (0.010) M G T A S N J 14 PL M 0.25 (0.010) M T B S DIM A B C D F G J K L M N MILLIMETERS MIN MAX 19.05 6.23 3.94 0.39 1.40 19.94 7.11 5.08 0.50 1.65 INCHES MIN MAX 0.750 0.245 0.155 0.015 0.055 0.785 0.280 0.200 0.020 0.065 2.54 BSC 0.21 3.18 0.38 4.31 0.100 BSC 0.008 0.125 0.015 0.170 7.62 BSC 0 ° 15 ° 0.300 BSC 0 ° 15 ° 0.51 1.01 0.020 0.040 Case 646-06 N Suffix 14-Pin Plastic NOTES: 1. LEADS WITHIN 0.13 mm (0.005) RADIUS OF TRUE POSITION AT SEATING PLANE AT MAXIMUM MATERIAL CONDITION. 14 8 B 1 7 2. DIMENSION L" TO CENTER OF LEADS WHEN FORMED PARALLEL. 3. DIMENSION B" DOES NOT INCLUDE MOLD FLASH. 4. 5. ROUNDED CORNERS OPTIONAL. 646 05 OBSOLETE, NEW STANDARD 646 06. A F C N H G D SEATING PLANE NOTE 4 L J K M DIM A B C D F G H J K L M N MILLIMETERS MIN MAX 18.16 6.10 3.69 0.38 1.02 19.56 6.60 4.69 0.53 1.78 INCHES MIN MAX 0.715 0.240 0.145 0.015 0.040 0.770 0.260 0.185 0.021 0.070 2.54 BSC 1.32 0.20 2.92 2.41 0.38 3.43 0.100 BSC 0.052 0.008 0.115 0.095 0.015 0.135 7.62 BSC 0 ° 10 ° 0.300 BSC 0 ° 10 ° 0.39 1.01 0.015 0.039 FAST AND LS TTL DATA 5-191