SN74LS145D

SN54/74LS145 1-OF-10 DECODER/DRIVER OPEN-COLLECTOR The SN54 / 74LS145, 1-of-10 Decoder/Driver, is designed to accept BCD inputs and provide appropriate outputs to drive 10-digit incandescent displays. All outputs remain off for all invalid binary input conditions. It is designed for use as indicator/relay drivers or as an open-collector logic circuit driver. Each of the high breakdown output transistors will sink up to 80 mA of current. Typical power dissipation is 35 mW. This device is fully compatible with all TTL families. • Low Power Version of 54 / 74145 • Input Clamp Diodes Limit High Speed Termination Effects 1-OF-10 DECODER/ DRIVER OPEN-COLLECTOR LOW POWER SCHOTTKY CONNECTION DIAGRAM DIP (TOP VIEW) V CC 16 P 0 15 P 1 14 P 2 13 P 3 12 Q 9 11 Q 8 10 Q 7 J SUFFIX CERAMIC CASE 620-09 16 1 9 16 1 Q 0 2 Q 1 3 Q 2 4 Q 3 5 Q 4 6 Q 5 7 Q 6 8 GND N SUFFIX PLASTIC CASE 648-08 1 PIN NAMES P0, P1, P2, P3 Q0 to Q9 BCD Inputs Outputs (Note b) LOADING (Note a) HIGH 0.5 U.L. Open Collector LOW 0.25 U.L. 15 (7.5) U.L. 16 1 D SUFFIX SOIC CASE 751B-03 NOTES: a) 1 TTL Unit Load (U.L.) = 40 µA HIGH/1.6 mA LOW. b) The Output LOW drive factor is 2.5 U.L. for Military (54) and 15 U.L. for Commercial (74) Temperature Ranges. ORDERING INFORMATION SN54LSXXXJ SN74LSXXXN SN74LSXXXD Ceramic Plastic SOIC LOGIC DIAGRAM P 0 INPUTS P 1 P 2 P 3 LOGIC SYMBOL 15 14 INPUT INVERTERS P 0 13 12 0 0 1 1 2 2 3 3 P P 1 2 P 3 Q Q Q Q Q Q Q Q Q Q 0 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 9 10 11 DECODE/DRIVER GATES V = PIN 16 CC GND = PIN 8 Q 0 Q 1 Q 2 Q 3 Q 4 Q 5 Q 6 Q 7 Q 8 Q 9 OUTPUTS FAST AND LS TTL DATA 5-240 SN54/74LS145 TRUTH TABLE INPUTS P3 L L L L L L L L H H H H H H H H P2 L L L L H H H H L L L L H H H H P1 L L H H L L H H L L H H L L H H P0 L H L H L H L H L H L H L H L H Q0 L H H H H H H H H H H H H H H H Q1 H L H H H H H H H H H H H H H H Q2 H H L H H H H H H H H H H H H H Q3 H H H L H H H H H H H H H H H H OUTPUTS Q4 H H H H L H H H H H H H H H H H Q5 H H H H H L H H H H H H H H H H Q6 H H H H H H L H H H H H H H H H Q7 H H H H H H H L H H H H H H H H Q8 H H H H H H H H L H H H H H H H Q9 H H H H H H H H H L H H H H H H H = HIGH Voltage Level L = LOW Voltage Level GUARANTEED OPERATING RANGES Symbol VCC TA VOH IOL Supply Voltage Operating Ambient Temperature Range Output Voltage — High Output Current — Low Parameter 54 74 54 74 54, 74 54 74 Min 4.5 4.75 – 55 0 Typ 5.0 5.0 25 25 Max 5.5 5.25 125 70 15 12 24 Unit V °C V mA FAST AND LS TTL DATA 5-241 SN54/74LS145 DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified) Limits Symbol VIH VIL VIK IOH VOL Parameter Input HIGH Voltage Input LOW Voltage Input Clamp Diode Voltage Output HIGH Current 54, 74 54, 74 Output LOW Voltage 74 54, 74 IIH IIL ICC Input HIGH Current Input LOW Current Power Supply Current 0.25 0.35 2.3 54 74 – 0.65 Min 2.0 0.7 0.8 – 1.5 250 0.4 0.5 3.0 20 0.1 – 0.4 13 V µA V V V µA mA mA mA Typ Max Unit V V Test Conditions Guaranteed Input HIGH Voltage for All Inputs Guaranteed Input LOW Voltage for All Inputs VCC = MIN, IIN = – 18 mA VCC = MIN, VOH = MAX IOL = 12 mA IOL = 24 mA IOL = 80 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX, VIN = GND AC CHARACTERISTICS (TA = 25°C) Limits Symbol tPHL tPLH Propagation Delay Pn Input to Qn Output Parameter Min Typ Max 50 50 Unit ns Test Conditions VCC = 5.0 V CL = 45 pF AC WAVEFORMS V IN 1.3 V 1.3 V V IN 1.3 V 1.3 V t PHL t PLH t PHL t PLH V OUT 1.3 V 1.3 V V OUT 1.3 V 1.3 V Figure 1 Figure 2 FAST AND LS TTL DATA 5-242 -A- Case 751B-03 D Suffix 16-Pin Plastic SO-16 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. 3. CONTROLLING DIMENSION: MILLIMETER. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. 751B 01 IS OBSOLETE, NEW STANDARD 751B 03. 16 9 -B1 8 P 8 PL 0.25 (0.010) M B M R X 45° G -TD 16 PL 0.25 (0.010) M C SEATING PLANE K T B S M F J A S DIM A B C D F G J K M P R MILLIMETERS MIN MAX 9.80 3.80 1.35 0.35 0.40 10.00 4.00 1.75 0.49 1.25 INCHES MIN MAX 0.386 0.150 0.054 0.014 0.016 0.393 0.157 0.068 0.019 0.049 1.27 BSC 0.19 0.10 0 0.25 0.25 7 0.050 BSC 0.008 0.004 0 0.009 0.009 7 ° ° ° ° 5.80 0.25 6.20 0.50 0.229 0.010 0.244 0.019 Case 648-08 N Suffix 16-Pin Plastic -A16 9 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. 3. CONTROLLING DIMENSION: INCH. DIMENSION L" TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B" DOES NOT INCLUDE MOLD FLASH. 5. 6. ROUNDED CORNERS OPTIONAL. 648 01 THRU 07 OBSOLETE, NEW STANDARD 648 08. B 1 8 F S C -TK SEATING PLANE L H G D 16 PL 0.25 (0.010) M J M T A M DIM A B C D F G H J K L M S MILLIMETERS MIN MAX 18.80 6.35 3.69 0.39 1.02 19.55 6.85 4.44 0.53 1.77 INCHES MIN MAX 0.740 0.250 0.145 0.015 0.040 0.770 0.270 0.175 0.021 0.070 2.54 BSC 1.27 BSC 0.21 2.80 7.50 0 0.38 3.30 7.74 10 0.100 BSC 0.050 BSC 0.008 0.110 0.295 0 0.015 0.130 0.305 10 ° ° ° ° 0.51 1.01 0.020 0.040 -A16 9 Case 620-09 J Suffix 16-Pin Ceramic Dual In-Line NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. -B1 8 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIM F MAY NARROW TO 0.76 (0.030) WHERE THE LEAD ENTERS THE CERAMIC BODY. C L 5. 620 01 THRU 08 OBSOLETE, NEW STANDARD 620 09. -TSEATING PLANE K E F D 16 PL 0.25 (0.010) M N G T A S M J 16 PL 0.25 (0.010) M T B S DIM A B C D E F G J K L M N MILLIMETERS MIN MAX 19.05 6.10 19.55 7.36 4.19 0.39 0.53 INCHES MIN MAX 0.750 0.240 0.770 0.290 0.165 0.015 0.021 1.27 BSC 1.40 1.77 0.050 BSC 0.055 0.070 2.54 BSC 0.23 0.27 5.08 7.62 BSC 0 0.100 BSC 0.009 0.011 0.200 0.300 BSC 0 ° 15 ° ° 15 ° 0.39 0.88 0.015 0.035 FAST AND LS TTL DATA 5-243 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Literature Distribution Centers: USA: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. EUROPE: Motorola Ltd.; European Literature Centre; 88 Tanners Drive, Blakelands, Milton Keynes, MK14 5BP, England. JAPAN: Nippon Motorola Ltd.; 4-32-1, Nishi-Gotanda, Shinagawa-ku, Tokyo 141, Japan. ASIA PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Center, No. 2 Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong. ◊ FAST AND LS TTL DATA 5-244