A523RHI

A500RHI Series Very High Isolation, 5W Single & Dual Output DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: • 5W Output Power • 5,600 VDC Isolation • 2 µA Leakage Current Max • Wide 2:1 Input Range • Compact DIP Case • Single & Dual Outputs • Meets EN55022 • 700 kH MTBF • EN60950 Approved Input Parameter Input Start Voltage Conditions Min. Typ. Max. 12 VDC Input 7.0 8.0 9.0 24 VDC Input 13.0 15.0 18.0 48 VDC Input 30.0 33.0 36.0 12 VDC Input 8.5 24 VDC Input 16.0 48 VDC Input 34.0 (Pi) Filter (Complies with EN55022 Class A) 0.3 3,000 Conditions Dual Output , Balanced Loads Vin = Min to Max Iout = 10% to 100% 5V Output All Other Outputs Over Line, Load & Temp. 120 50% Load Step Change 300 ±3.0 ±0.02 Continuous (Autorecovery) Min. 5,600 6,000 1,000 7 150 13 Typ. 500 ±6.0 ±0.05 Min. Typ. ±0.5 ±0.5 ±0.3 ±0.5 75 100 Max. ±1.0 ±2.0 ±0.5 ±1.0 100 150 180 25 Units VDC Under Voltage Shutdown Input Filter Reverse Polarity Input Current Short Circuit Input Power VDC A mW Units % % % % mV P - P mV P - P mV rms % µSec % %/ºC Output Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation Ripple & Noise (20 MHz) (Note 1) Ripple & Noise (20 MHz) Ripple & Noise (20 MHz) Output Power Protection Transient Recovery Time (Note 2) Transient Response Deviation Temperature Coefficient Output Short Circuit General Parameter Isolation Voltage, Rated Isolation Test Voltage Leakage Current Isolation Resistance Isolation Capacitance Switching Frequency Conditions 60 Seconds 60 Seconds 240 VAC, 60 Hz 500 VDC 100 kHz, 1V Max. Units VDC VDC µA M pF kHz Units ºC ºC ºC % 2 Environmental Parameter Operating Temperature Range Operating Temperature Range Storage Temperature Range Cooling Humidity Conditions Min. Typ. -40 -40 -40 Free Air Convection RH, Non-condensing Ambient Case Max. +55 +95 +125 95 MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com Physical Case Size Case Material Weight 1.25 x 0.80 x 0.40 Inches (31.8 x 20.3 x 10.2 mm) Non-Conductive Black Plastic (UL94-V0) 0.57 Oz (16.2g) Conditions MIL HDBK 217F, 25ºC, Gnd Benign Conditions 12 VDC Input 24 VDC Input 48 VDC Input 1.5 mm From Case For 10 Sec All Models Min. 700 Min. -0.7 -0.7 -0.7 Typ. Max. Units kHours Units VDC ºC mW Reliability Specifications Parameter MTBF Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation Typ. Max. 25.0 50.0 100.0 260 2,500 Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. www.micropowerdirect.com Model Selection Guide Input Model Number A501RHI A502RHI A503RHI A504RHI A511RHI A512RHI A513RHI A514RHI A521RHI A522RHI A523RHI A524RHI Voltage (VDC) Nominal 12 12 12 12 24 24 24 24 48 48 48 48 Range 9.0 - 18.0 9.0 - 18.0 9.0 - 18.0 9.0 - 18.0 18.0 - 36.0 18.0 - 36.0 18.0 - 36.0 18.0 - 36.0 36.0 - 75.0 36.0 - 75.0 36.0 - 75.0 36.0 - 75.0 www.micropowerdirect.com Output Reflected Fuse Rating Efficiency Ripple Current (mA) Slow-Blow Current (%, Typ) Current Voltage Current (mA) Full-Load No-Load (mA, Typ) (VDC) (mA, Max) (mA, Min) 570 641 641 641 278 313 313 313 139 156 156 156 30 30 30 30 20 20 20 20 10 10 10 10 60 60 60 60 30 30 30 30 15 15 15 15 5.0 12.0 ±12.0 ±15.0 5.0 12.0 ±12.0 ±15.0 5.0 12.0 ±12.0 ±15.0 1,000 500 ±250 ±200 1,000 500 ±250 ±200 1,000 500 ±250 ±200 200.0 100.0 ±50.0 ±40.0 200.0 100.0 ±50.0 ±40.0 200.0 100.0 ±50.0 ±40.0 75 78 78 78 77 80 80 80 77 80 80 80 1,200 1,200 1,200 1,200 600 600 600 600 300 300 300 300 Notes: 1. When measuring output ripple, it is recommended that an external 0.47 µF ceramic capacitor be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. For noise sensitive applications, the use of 3.3 µF capacitors will reduce the output ripple. 2. Transient recovery is measured to within a 1% error band for a load step change of 75% to 100%. 3. Dual output units may be connected to provide a 24 VDC or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common. 4. The converter should be connected to a low ac-impedance source. An input source with a highly inductive impedance may affect the stability of the converter. In applications where the converter output loading is high and input power is supplied over long lines, it may be necessary to use a capacitor on the input to insure start-up. In this case, it is recommended that a low ESR (ESR