A612ERU

A600ERU Series Single & Dual Output, 6W Ultra-Wide Input Range DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Key Features: • 6W Output Power • 4:1 Input Voltage Range • 1,500 VDC Isolation • -40ºC to +85ºC Temp Range • Compact DIP Case • Single & Dual Outputs • 1.0 MH MTBF • Industry Standard Pin-Out • Low, Low Cost Parameter Input Voltage Range (See Note 1) Input Filter Reverse Polarity Input Current Short Circuit Input Power Conditions 24 VDC Input 48 VDC Input Min. 9.0 18.0 Typ. 24.0 48.0 Max. 36.0 72.0 1.0 2,500 Units VDC Capacitors A mW Units % % ±0.5 ±1.0 50 300 ±0.02 % % mV P - P mV P - P % ±0.01 Continuous Conditions 60 Seconds 500 VDC Single Output Dual Output Conditions Ambient Min. -40 -55 Free Air Convection RH, Non-condensing 95 % Min. 1,500 1,000 300 250 Typ. Max. +85 +125 Typ. Max. Units VDC M kHz %/ºC Output Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation Noise (20 Hz - 300 kHz) Ripple (DC - 20 MHz) Output Power Protection Temperature Coefficient Output Short Circuit 120 Conditions See Note 2 Dual Output , Balanced Loads Vin = Min to Max See Note 3 See Note 4 Min. Typ. ±1.0 ±3.0 ±0.2 ±0.5 30 100 Max. ±3.0 General Parameter Isolation Voltage Isolation Resistance Switching Frequency Environmental Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Physical Case Size 1.25 x 0.80 x 0.40 Inches (31.8 x 20.3 x 10.2 mm) Metal With Non-Conductive Base (UL94V-0) 0.49 Oz (14g) Conditions MIL HDBK 217F, 25ºC, Gnd Benign Conditions 24 VDC Input 48 VDC Input 1.5 mm From Case For 10 Sec All Models Min. 1.0 Min. -0.7 -0.7 Typ. Max. 50.0 100.0 300 2,500 Typ. Max. Units MHours Units VDC ºC mW Units ºC ºC MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com Case Material Weight Reliability Specifications Parameter MTBF Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. www.micropowerdirect.com Model Selection Guide Model Number A601ERU A602ERU A603ERU A604ERU A605ERU A606ERU A607ERU A608ERU A609ERU A611ERU A612ERU A613ERU A614ERU A615ERU A616ERU A617ERU A618ERU A619ERU Voltage (VDC) Nominal 24 24 24 24 24 24 24 24 24 48 48 48 48 48 48 48 48 48 Range 9.0 - 36.0 9.0 - 36.0 9.0 - 36.0 9.0 - 36.0 9.0 - 36.0 9.0 - 36.0 9.0 - 36.0 9.0 - 36.0 9.0 - 36.0 18.0 - 72.0 18.0 - 72.0 18.0 - 72.0 18.0 - 72.0 18.0 - 72.0 18.0 - 72.0 18.0 - 72.0 18.0 - 72.0 18.0 - 72.0 Input Current (mA) www.micropowerdirect.com Output Fuse Rating Reflected Efficiency Slow-Blow Current Ripple Voltage Current (%, Typ) (mA) (VDC) (mA, Max) (mA, Min) Full-Load No-Load Current (mA, Typ) 278 312 304 304 301 312 304 298 294 137 156 152 147 145 156 152 149 147 20 20 20 20 20 20 20 20 20 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 3.3 5.0 12.0 15.0 24.0 ±5.0 ±12.0 ±15.0 ±24.0 3.3 5.0 12.0 15.0 24.0 ±5.0 ±12.0 ±15.0 ±24.0 1,500 1,200 500 400 250 ±600 ±250 ±200 ±125 1,500 1,200 500 400 250 ±600 ±250 ±200 ±125 150.0 120.0 50.0 40.0 25.0 ±60.0 ±25.0 ±20.0 ±13.0 150.0 120.0 50.0 40.0 25.0 ±60.0 ±25.0 ±20.0 ±13.0 75 80 82 82 83 80 82 84 85 76 80 82 85 86 80 82 84 85 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 750 750 750 750 750 750 750 750 750 Notes: 1. Exceeding the input range by a significant margin may damage the units. For 24V input the input voltage should not exceed 40V; for 48V models it should not exceed 80V. 2. Output accuracy for the negative output of dual output units is typically ±3% (±5% max.). 3. Output load regulation is specified for a load change of 10% to 100%. For 3.3V output units, the load regulation is ±1.5% max. 4. When measuring output ripple, it is recommended that an external 0.33 µF ceramic capacitor be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. 5. These units should not be operated with a load under the specified minimum. Operation at no-load will increase ripple significantly and may cause damage to the unit. 6. These converters are specified for operation without external components. However, in some applications the addition of input/output capacitors will enhance stability and reduce output ripple. Recommended capacitor values are: Derating Curve Input Vout Capacitor 24 VDC 100 µF 3.3 VDC 48 VDC 100 µF 5 VDC 12 VDC 15 VDC 24 VDC Vin Output Capacitor 100 µF 100 µF 100 µF 47 µF 47 µF Mechanical Dimensions For applications requiring very low output noise levels, a simple LC filter should be effective. 7. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Pin Connections Pin 2, 3 9 11 14 16 22, 23 Single -Vin No Pin NC +Vout -Vout +Vin Dual -Vin Common -Vout +Vout Common +Vin NC: No Connection MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • Mechanical Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com