E133I

E100I Series High Isolation Miniature, 1W SIP DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. New Models!! Conditions 5 VDC Input 12 VDC Input 24 VDC Input 48 VDC Input Min. 4.5 10.8 21.6 43.2 Typ. 5.0 12.0 24.0 48.0 Max. 5.5 13.2 26.4 52.8 0.3 Units Key Features: • 1W Output Power • Miniature SIP Case • 3,000 VDC Isolation • Complies to RFI Standards • >2 MHour MTBF • 20 Standard Models • Industry Standard Pin-Out Input Parameter Input Voltage Range VDC Reverse Polarity Input Current Input Filter A Internal Capacitor Conditions Min. Typ. Max. ±3.0 Units % % mV P - P % %/ºC Output Parameter Output Voltage Accuracy Line Regulation Load Regulation (Note 1) Ripple & Noise (20 MHz) (Note 2) Output Power Protection Temperature Coefficient Output Short Circuit For Vin Change of 1% ±1.2 See Model Selection Guide 60 110 ±0.01 Momentary (0.5 Sec.) Conditions Min. 3,000 1,000 Typ. ±0.02 RoHS Compliant General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency EMI/RFI Units VDC MΩ 60 pF 50 kHz EN55022 A, EN55024 A, IEC 61000-4-2, IEC 61000-4-3, FCC 47 CFR Part 15 B 60 Seconds 1,000 VDC 100 kHz, 1V Conditions Ambient Case Min. -40 Typ. +25 Max. +85 +100 +125 95 Units ºC ºC ºC % Max. Environmental Parameter Operating Temperature Range Operating Temperature Range Storage Temperature Range Cooling Humidity -40 Free Air Convection RH, Non-condensing Physical MicroPower Direct 232 Tosca Drive Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com Case Size (5V, 12V & 24V Input Models) Case Size (48V Input Models) Case Material Weight 0.46 x 0.24 x 0.40 Inches (11.68 x 6.0 x 10.2 mm) 0.46 x 0.29 x 0.40 Inches (11.68 x 7.5 x 10.2 mm) Non-Conductive Black Plastic (UL94-V0) 0.06 Oz (1.8g) Conditions MIL HDBK 217F, 25ºC, Gnd Benign Conditions 5 VDC Input 12 VDC Input 24 VDC Input 48 VDC Input 1.5 mm From Case For 10 Sec All Models Min. 2.0 Min. -0.7 -0.7 -0.7 -0.7 Typ. Max. Units MHours Units Reliability Specifications Parameter MTBF Absolute Maximum Ratings Parameter Typ. Max. 7.0 15.0 28.0 54.0 260 650 Input Voltage Surge (1 Sec) VDC Lead Temperature Internal Power Dissipation ºC mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Model Selection Guide Model Number E101I E102I E103I E104I E105I E111I E112I E113I E114I E115I E121I E122I E123I E124I E125I E131I E132I E133I E134I E135I Load Input Output Voltage Current Current Regulation Voltage (VDC) Current (mA) Nominal Range Full-Load No-Load (VDC) (mA, Max) (mA, Min) (% Max) 5 4.5 - 5.5 267 25 5.0 200.0 4.0 10 5 4.5 - 5.5 260 25 9.0 111.0 2.0 10 5 4.5 - 5.5 256 25 12.0 83.3 2.0 10 5 4.5 - 5.5 257 25 15.0 66.6 2.0 10 5 4.5 - 5.5 257 25 24.0 41.6 2.0 10 12 10.8 - 13.2 112 16 5.0 200.0 4.0 10 12 10.8 - 13.2 109 16 9.0 111.0 2.0 10 12 10.8 - 13.2 107 16 12.0 83.3 2.0 10 12 10.8 - 13.2 107 16 15.0 66.6 2.0 10 12 10.8 - 13.2 107 16 24.0 41.6 2.0 10 24 21.6 - 26.4 56 10 5.0 200.0 4.0 10 24 21.6 - 26.4 55 10 9.0 111.0 2.0 10 24 21.6 - 26.4 54 10 12.0 83.3 2.0 10 24 21.6 - 26.4 54 10 15.0 66.6 2.0 10 24 21.6 - 26.4 54 10 24.0 41.6 2.0 10 48 43.2 - 52.8 28 7 5.0 200.0 4.0 10 48 43.2 - 52.8 27 7 9.0 111.0 2.0 10 48 43.2 - 52.8 27 7 12.0 83.3 2.0 10 48 43.2 - 52.8 27 7 15.0 66.6 2.0 10 48 43.2 - 52.8 27 7 24.0 41.6 2.0 10 Efficiency (%, Typ) 75 77 78 78 78 75 77 78 78 78 75 77 78 78 78 75 76 76 76 76 Fuse Rating Slow-Blow (mA) 500 500 500 500 500 200 200 200 200 200 100 100 100 100 100 50 50 50 50 50 Models with other outputs are available. Contact the factory for details!! Notes: 1. Output load regulation is specified for a load change of 20% to 100%. 2. When measuring output ripple, it is recommended that an external 0.33 µF ceramic capacitor be placed from the +Vout pin to the -Vout pin. 3. Operation at no-load will not damage these units. However, they may not meet all specifications. 4. The 5V, 12V and 24V input units do not require external components to operate, but the use of a low ESR capacitor (approximately 10 uF, ESR