G102R

MicroPower Direct Tightly Regulated, 1W Ultra-Miniature DIP DC/DC Converters Key Features Miniature DIP Package !0.5% Line/Load Regulation 2.7 MH MTBF 1.0 kVDC Isolation 1W Output Power Low Cost G100R Series Electrical Specifications Specifications typical @ +251C with nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Parameter Input Voltage Range Input Filter Conditions 5 VDC Input 12 VDC Input 24 VDC Input Min. 4.5 10.8 21.6 Typ. 5.0 12.0 24.0 Max. 5.5 13.2 26.4 VDC Units Internal Capacitor Conditions For Vin Change of Min to Max For Iout = 20% to 100% 120 !0.01 Momentary (0.5 Sec.) Conditions 60 Seconds 500 VDC 100 kHz, 1V Min. 1,000 1,000 60 80 Conditions Min. -40 -40 Free Air Convection RH, Non-condensing 95 % Typ. +25 Max. +85 +125 Typ. Max. Units VDC MΩ pF kHz Units 1C 1C !0.02 Min. Typ. !1.0 Max. !5.0 !0.5 !0.5 50 Units % % % mV P - P % %/1C Output Parameter Output Voltage Accuracy Line Regulation Load Regulation Ripple & Noise (20 MHz) Output Power Protection Temperature Coefficient Output Short Circuit General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Environmental Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Physical Case Size Case Material Weight 0.80 x 0.40 x 0.27 Inches (20.32 x 10.16 x 6.85 mm) Non-Conductive Black Plastic 0.09 Oz (2.7g) Conditions MIL HDBK 217F, 251C, Gnd Benign Conditions 5 VDC Input Input Voltage Surge (1 Sec) Internal Power Dissipation 12 VDC Input 24 VDC Input All Models Min. -0.7 -0.7 -0.7 Min. Typ. 2.7 Typ. Max. 6.0 14.0 28.0 450 mW VDC Max. Units MHours Units Reliability Specifications Parameter MTBF Absolute Maximum Ratings Parameter Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. MicroPower Direct TEL: (781) 344-8226 FAX: (781) 344-8481 E-Mail: sales@micropowerdirect.com WEB: www/micropowerdirect.com Model Selection Guide Model Number G101R G102R G103R G104R G105R G111R G112R G113R G114R G115R G121R G122R G123R G124R G125R Notes: 1. These units do not require external comonents to operate, but the use of an input capacitor (10 µF) may enhance performance in some applications. An output capacitor (4.7 µF to 10 µF) may be used to reduce ripple. Input Voltage (VDC) Current (mA) Nominal Range Full-Load No-Load 5 4.5 - 5.5 213 28 5 4.5 - 5.5 317 28 5 4.5 - 5.5 312 26 5 4.5 - 5.5 312 26 5 4.5 - 5.5 312 38 12 10.8 - 13.2 91 16 12 10.8 - 13.2 130 16 12 10.8 - 13.2 130 16 12 10.8 - 13.2 130 16 12 10.8 - 13.2 130 16 24 21.6 - 26.4 43 7 24 21.6 - 26.4 64 7 24 21.6 - 26.4 65 9 24 21.6 - 26.4 65 9 24 21.6 - 26.4 65 9 Voltage (VDC) 3.3 5.0 9.0 12.0 15.0 3.3 5.0 9.0 12.0 15.0 3.3 5.0 9.0 12.0 15.0 Output Current (mA, Max) 200.0 200.0 111.0 83.0 66.0 200.0 200.0 111.0 83.0 66.0 200.0 200.0 111.0 83.0 66.0 Current (mA, Min) 20.0 20.0 11.0 9.0 7.0 20.0 20.0 11.0 9.0 7.0 20.0 20.0 11.0 9.0 7.0 Efficiency (%, Typ) 62 63 64 64 66 61 64 64 64 64 63 65 64 64 64 Fuse Rating Slow-Blow (mA) 500 500 500 500 500 200 200 200 200 200 100 100 100 100 100 Derating Curve 100 80 Output Power % 60 40 20 0 -40 -20 0 5 15 25 35 45 55 65 75 85 95 105 Ambient Temperature 1C Capacitive Load µF Max 33 Mechanical Dimensions Side 0.27 (6.85) 0.12 (3.05) Pin Connections Pin 1 7 9 11 14 Single -Vin NC +Vout -Vout +Vin 0.10 (2.54) 0.10 (2.54) 0.60 (15.24) 0.80 (20.32) 1 7 Bottom 14 11 9 0.40 (10.2) NC = No Connection Notes: All dimensions are typical in inches (mm) Tolerance x.xx = !0.01 (!0.25) Pin 1 is marked by a “dot” or indentation on the side of the unit 0.01 (0.25) 0.01 (0.25) 0.05 (1.25) MicroPower Direct 232 Tosca Drive, Stoughton, MA 02072 www.micropowerdirect.com sales@micropowerdirect.com phone: (781) 344 - 8226 * fax: (781) 344 - 8481