G128EI

G100EI Key Features: • 1W Output Power • Compact “MiniDIP” Case • 3,000 VDC Isolation • UL Approved (File E245422) • Single & Dual Outputs • >3.5 MHour MTBF • 24 Standard Models • LOWEST COST!! Input Parameter Input Voltage Range Input Filter Series Low Cost, 1W MiniDIP High Isolation DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Conditions 5 VDC Input 12 VDC Input 24 VDC Input Min. 4.5 10.8 21.6 Typ. 5.0 12.0 24.0 Max. 5.5 13.2 26.4 0.3 Units VDC Internal Capacitor A Units % % % 75 ±0.03 mV P - P % ±0.02 Momentary (1.0 Sec.) Conditions 60 Seconds 500 VDC 100 kHz, 1V Min. 3,000 1,000 60 150 Conditions Ambient Min. -40 -55 Free Air Convection RH, Non-condensing 95 % Typ. +25 Max. +85 +125 Typ. Max. Units VDC MΩ pF kHz Units ºC ºC %/ºC Reverse Polarity Input Current Output Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation (Note 1) Ripple & Noise (20 MHz) (Note 2) Output Power Protection Temperature Coefficient Output Short Circuit 120 Dual Output , Balanced Loads For Vin Change of 1% Conditions Min. Typ. ±1.0 ±0.1 ±1.2 50 Max. ±3.0 ±1.0 See Model Selection Guide RoHS Compliant General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Environmental Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Physical MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com Case Size Case Material Weight 0.80 x 0.40 x 0.25 Inches (20.4 x 10.2 x 6.5 mm) Non-Conductive Black Plastic (UL94-V0) 0.07 Oz (2.1g) Conditions MIL HDBK 217F, 25ºC, Gnd Benign Min. 3.5 Typ. Max. Units MHours Reliability Specifications Parameter MTBF Safety Standards Safety Approvals UL 1950, EN 60950, IEC 60950 UL, cUL; File No. E245422 Conditions 5 VDC Input 12 VDC Input 24 VDC Input 1.5 mm From Case For 10 Sec All Models Min. -0.7 -0.7 -0.7 Typ. Max. 9.0 18.0 30.0 300 450 ºC mW VDC Units Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Model Selection Guide Model Number G101EI G102EI G103EI G104EI G105EI G106EI G107EI G108EI G111EI G112EI G113EI G114EI G115EI G116EI G117EI G118EI G121EI G122EI G123EI G124EI G125EI G126EI G127EI G128EI Input Output Load Voltage (VDC) Current (mA) Regulation Voltage Current Current Nominal Range Full-Load No-Load (VDC) (mA, Max) (mA, Min) (%, Max) 5 4.5 - 5.5 286 30 5.0 200.0 20.0 15 5 4.5 - 5.5 267 30 9.0 111.0 12.0 15 5 4.5 - 5.5 256 30 12.0 83.0 9.0 15 5 4.5 - 5.5 250 30 15.0 67.0 7.0 15 5 4.5 - 5.5 278 30 ±5.0 ±100.0 ±10.0 15 5 4.5 - 5.5 267 30 ±9.0 ±56.0 ±6.0 15 5 4.5 - 5.5 256 30 ±12.0 ±42.0 ±5.0 15 5 4.5 - 5.5 253 30 ±15.0 ±33.0 ±4.0 15 12 10.8 - 13.2 115 15 5.0 200.0 20.0 15 12 10.8 - 13.2 110 15 9.0 111.0 12.0 15 12 10.8 - 13.2 105 15 12.0 83.0 9.0 15 12 10.8 - 13.2 103 15 15.0 67.0 7.0 15 12 10.8 - 13.2 113 15 ±5.0 ±100.0 ±10.0 15 12 10.8 - 13.2 110 15 ±9.0 ±56.0 ±6.0 15 12 10.8 - 13.2 105 15 ±12.0 ±42.0 ±5.0 15 12 10.8 - 13.2 104 15 ±15.0 ±33.0 ±4.0 15 24 21.6 - 26.4 57 8 5.0 200.0 20.0 15 24 21.6 - 26.4 54 8 9.0 111.0 12.0 15 24 21.6 - 26.4 52 8 12.0 83.0 9.0 15 24 21.6 - 26.4 51 8 15.0 67.0 7.0 15 24 21.6 - 26.4 56 8 ±5.0 ±100.0 ±10.0 15 24 21.6 - 26.4 55 8 ±9.0 ±56.0 ±6.0 15 24 21.6 - 26.4 52 8 ±12.0 ±42.0 ±5.0 15 24 21.6 - 26.4 51 8 ±15.0 ±33.0 ±4.0 15 Efficiency (%, Typ) 70 75 78 80 72 75 78 79 72 76 79 81 74 76 79 80 73 77 80 82 74 76 80 81 Fuse Rating Slow-Blow (mA) 500 500 500 500 500 500 500 500 200 200 200 200 200 200 200 200 100 100 100 100 100 100 100 100 Other input/output combinations are available (i.e 3.3 VDC). Contact the factory for details at: sales@micropowerdirect.com Notes: 1. Output load regulation is specified for a load change of 10% to 100%. 2. These units should not be operated with a load under 10% of full load. Operation at no-load may cause damage to the unit. 3. These converters will operate without external components. However, when measuring output ripple, it is recommended that an external ceramic capacitor be placed Output Capacitor Input from the +Vout pin to Vin Vout Capacitor Single Dual the -Vout pin for single output units and from 5 VDC 4.7 μF 5 VDC 10.0 μF 4.7 μF each output to common 12 VDC 2.2 μF 9 VDC 4.7 μF 2.2 μF for dual output units. 24 VDC 1.0 μF 12 VDC 2.2 μF 1.0 μF An input capacitor will 15 VDC 1.0 μF 0.47 μF enhance stability over temperature and input line variations. Recommended capacitor values are given in the table above. For applications requiring very low output noise levels, a simple LC filter should be effective. 4. Dual output units may be connected to provide a 10V, 18V, 24V or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common 5. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Derating Curve Mechanical Dimensions Pin Connections Pin Single Dual Pin 9 10 14 Single No Pin -Vout +Vin Dual Common -Vout +Vin 1 -Vin -Vin 7 NC NC 8 +Vout +Vout NC= No Connection Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) • Pin 1 is marked by a “dot” or indentation on the side of the unit MicroPower Direct www.micropowerdirect.com 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com