LF112S

LF100S Series Ultra-Miniature, 1W Single Output SMT DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Key Features: • 1W Output Power • Ultra-Miniature SMT Case • 1,000 VDC Isolation • 5V, 12V & 24V Inputs • -40ºC to +85ºC Operation • 15 Standard Models • 2.0 MH MTBF Minimum • Industry Standard Pin-Out Parameter Input Voltage Range Reverse Polarity Input Current Input Filter Conditions 5 VDC Input 12 VDC Input 24 VDC Input Min. 4.5 10.8 21.6 Typ. 5.0 12.0 24.0 Max. 5.5 13.2 26.4 0.3 Units VDC A Capacitor Conditions For Vin Change of 1% Min. Typ. ±1.0 ±1.2 60 Over Line, Load & Temp. 120 ±0.01 Momentary (0.5 Sec.) Conditions 60 Seconds 500 VDC 100 kHz, 1V 50 Conditions Ambient Case Min. -40 -40 -40 Free Air Convection RH, Non-condensing 95 % Min. 1,000 1,000 40 100 Typ. +25 100 140 Max. +85 +90 +125 Typ. Max. Units VDC MΩ pF kHz Units ºC ºC ºC ±0.02 See Model Selection Guide 120 150 5 mV P - P mV P - P mv rms % %/ºC Max. ±3.0 ±1.5 Units % % Output Parameter Output Voltage Accuracy Line Regulation Load Regulation (Note 1) Ripple & Noise (20 MHz) (Note 2) Ripple & Noise (20 MHz) Ripple & Noise (20 MHz) Output Power Protection Temperature Coefficient Output Short Circuit RoHS Compliant General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Environmental Parameter Operating Temperature Range Operating Temperature Range Storage Temperature Range Cooling MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com Humidity Physical Case Size Case Material Weight 0.50 x 0.31 x 0.26 Inches (12.7 x 8.0 x 6.7 mm) Non-Conductive Black Plastic (UL94-V0) 0.05 Oz (1.5g) Conditions MIL HDBK 217F, 25ºC, Gnd Benign Conditions 5 VDC Input Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation 12 VDC Input 24 VDC Input 1.5 mm From Case For 10 Sec. All Models Min. 2.0 Min. -0.7 -0.7 -0.7 Typ. Max. 9.0 18.0 30.0 260 450 ºC mW VDC Typ. Max. Units MHours Units Reliability Specifications Parameter MTBF Absolute Maximum Ratings Parameter Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Model Selection Guide Input Model Number LF101S LF102S LF103S LF104S LF105S LF111S LF112S LF113S LF114S LF115S LF121S LF122S LF123S LF124S LF125S Voltage (VDC) Nominal 5 5 5 5 5 12 12 12 12 12 24 24 24 24 24 Range 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 21.6 - 26.4 21.6 - 26.4 21.6 - 26.4 21.6 - 26.4 21.6 - 26.4 Load Voltage Current Current Regulation Full-Load No-Load (VDC) (mA, Max) (mA, Min) (%, Max) Current (mA) 250 254 252 248 264 103 106 104 102 110 53 54 52 52 57 30 30 30 30 30 15 15 15 15 15 8 8 8 8 8 5.0 9.0 12.0 15.0 3.3 5.0 9.0 12.0 15.0 3.3 5.0 9.0 12.0 15.0 3.3 200.0 110.0 84.0 67.0 300.0 200.0 110.0 84.0 67.0 300.0 200.0 110.0 84.0 67.0 300.0 4.0 2.0 1.5 1.0 60.0 4.0 2.0 1.5 1.0 60.0 4.0 2.0 1.5 1.0 60.0 10 10 8 7 10 8 8 5 5 8 8 8 5 5 8 Output Efficiency (%, Typ) 80 78 80 81 75 81 78 81 82 75 79 77 80 80 73 Fuse Rating Slow-Blow (mA) 500 500 500 500 500 200 200 200 200 200 100 100 100 100 100 Notes: 1. Load regulation is measured for an output change of 20% to 100%. 2. When measuring output ripple, it is recommended that an external 0.33 μF ceramic capacitor be placed from the +Vout pin to the -Vout pin. For noise sensitive applications, the use of 0.47 μF capacitors will reduce the output ripple. 3. Operation at no-load will not damage these units. However, they may not meet all specifications. 4. The converter should be connected to a low ac-impedance source. An input source with a highly inductive impedance may affect the stability of the converter. In applications where the converter output loading is high and input power is supplied over long lines, it may be necessary to use a capacitor on the input to insure start-up. In this case, it is recommended that a low ESR (ESR