LF113ESI

LF100ESI Series Low Cost, Single Output 1W High Isolation SMT DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: • 1W Output Power • Ultra-Miniature SMT Case • 3,000 VDC Isolation • UL Approved (File E245422) • Single Output • Low 0.24” Profile • >3.5 MHour MTBF • 3.3, 5V, & 12V Inputs • LOWEST COST! Input Parameter Input Voltage Range Reverse Polarity Input Current Input Filter Capacitor Conditions For Vin Change of 1% See Model Selection Guide 60 ±0.01 Momentary (0.5 Sec.) Conditions 60 Seconds 500 VDC 100 kHz, 1V Min. 3,000 1,000 70 100 Conditions Ambient Min. -40 -55 Free Air Convection RH, Non-condensing 95 % Typ. +25 Max. +85 +125 Typ. Max. Units VDC M pF kHz Units ºC ºC 120 ±0.02 mV P - P %/ºC Min. Typ. ±3.0 ±1.2 Max. Units % % Conditions 3.3 VDC Input 5 VDC Input 12 VDC Input Min. 3.0 4.5 10.8 Typ. 3.3 5.0 12.0 Max. 3.6 5.5 13.2 1.0 A VDC Units Output Parameter Output Voltage Accuracy Line Regulation Load Regulation Ripple & Noise (20 MHz) Temperature Coefficient Output Short Circuit General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Environmental Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Physical Case Size Case Material Weight 0.60 x 0.30 x 0.24 Inches (15.24 x 7.5 x 6.0 mm) Non-Conductive Black Plastic (UL94-V0) 0.05 Oz (1.5g) Conditions MIL HDBK 217F, 25ºC, Gnd Benign Min. 3.5 Typ. Max. Units MHours Reliability Specifications MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com Parameter MTBF Safety Standards Safety Approvals UL 1950, EN 60950, IEC 60950 UL, cUL; File No. E245422 Conditions 3.3 VDC Input 5 VDC Input 12 VDC Input 1.5 mm From Case For 10 Sec All Models Min. -0.7 -0.7 -0.7 Typ. Max. 7.0 7.0 15.0 260.0 450 ºC mW VDC Units Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. www.micropowerdirect.com Model Selection Guide Model Number LF101ESI LF102ESI LF103ESI LF104ESI LF111ESI LF112ESI LF113ESI LF114ESI LF151ESI LF152ESI LF153ESI Input Voltage (VDC) Nominal Range 5 4.5 - 5.5 5 4.5 - 5.5 5 4.5 - 5.5 5 4.5 - 5.5 12 10.8 - 13.2 12 10.8 - 13.2 12 10.8 - 13.2 12 10.8 - 13.2 3.3 3.0 - 3.6 3.3 3.0 - 3.6 3.3 3.0 - 3.6 www.micropowerdirect.com Efficiency (%, Typ) 70 75 78 80 72 76 79 81 73 70 70 Fuse Rating Slow-Blow (mA) 500 500 500 500 200 200 200 200 750 750 750 Output Load Current (mA) Voltage Current Current Regulation Full-Load No-Load (VDC) (mA, Max) (mA, Min) (%, Max) 285 30 5.0 200.0 20.0 15.0 266 30 9.0 111.0 23.0 9.0 256 30 12.0 84.0 17.0 7.5 250 30 15.0 67.0 13.0 7.0 116 15 5.0 200.0 20.0 15.0 110 15 9.0 111.0 23.0 9.0 105 15 12.0 84.0 17.0 7.5 103 15 15.0 67.0 13.0 7.0 415 55 5.0 200.0 20.0 15.0 433 55 9.0 111.0 23.0 9.0 433 55 12.0 84.0 17.0 7.5 Notes: 1. Output load regulation is specified for a load change of 20% to 100%. 2. When measuring output ripple, it is recommended that an external 0.33 µF ceramic capacitor be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. 3. During operation, care must be taken not to exceed the specified input range of the unit or to allow the output load to drop below the specified minimum (10% of full load). Operating the unit under either of these conditions could cause damage to the unit. 4. These converters are specified for operation without external components. However, in some applications the addition of input/output capacitors will enhance stability and reduce output ripple. Recommended capacitor values are: Derating Curve Vin 3.3 VDC 5 VDC 12 VDC Input Capacitor 4.7 µF 4.7 µF 2.2 µF Vout 5 VDC 9 VDC 12 VDC 15 VDC Output Capacitor 4.7 µF 2.2 µF 1.0 µF 0.47 µF For applications requiring very low output noise levels, a simple LC filter should be effective. 5. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Pin Connections Pin 1 2 3 5 6 Description Pin Description -Vin 7 NC +Vin 8 +Vout NC 10 NC -Vout 11 NC NC 12 NC NC = No Connection Recommended Solder Profile Mechanical Dimensions Board Layout Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) • Pin 1 is marked by a “dot” or indentation on the unit MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com