LF152ES

厂商：
MPD
封装：
描述：
LF152ES - Lowest Cost, Single Output 1W Ultra-Miniature SMT DC/DC Converters - MicroPower Direct, LL...

数据手册：

下载LF152ES.pdf

立即购买

详情介绍
数据手册
价格&库存

LF152ES 数据手册

LF100ES Series Lowest Cost, Single Output 1W Ultra-Miniature SMT DC/DC Converters Electrical Speciﬁcations Speciﬁcations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Speciﬁcations subject to change without notice. Key Features: • 1W Output Power • Ultra-Miniature SMT Case • UL Approved (File E245422) • Single Output • Low 0.246” Proﬁle • 1,000 VDC Isolation • >3.5 MHour MTBF • 3.3V, 5V, & 12V Inputs • LOWEST COST! Input Parameter Input Voltage Range Reverse Polarity Input Current Input Filter Capacitor Conditions For Vin Change of 1% For Vin Change of 1% See Model Selection Guide 50 Momentary (0.5 Sec.) Conditions 60 Seconds 500 VDC 100 kHz, 1V Min. 1,000 1,000 70 100 Conditions Ambient Min. -40 -55 Free Air Convection RH, Non-condensing 95 % Typ. +25 Max. +85 +125 Typ. Max. Units VDC MΩ pF kHz Units ºC ºC 100 ±0.03 mV P - P %/ºC Min. Typ. ±3.0 ±1.5 ±1.2 Max. Units % % % Conditions 3.3 VDC Input 5 VDC Input 12 VDC Input Min. 3.0 4.5 10.8 Typ. 3.3 5.0 12.0 Max. 3.6 5.5 13.2 1.0 A VDC Units Output Parameter Output Voltage Accuracy Line Regulation, 3.3V Output Line Regulation, All Other Outputs Load Regulation Ripple & Noise (20 MHz) Temperature Coefﬁcient Output Short Circuit General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Environmental Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Physical MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA Case Size Case Material Weight 0.50 x 0.29 x 0.24 Inches (12.7 x 7.5 x 6.0 mm) Non-Conductive Black Plastic (UL94-V0) 0.05 Oz (1.5g) Conditions MIL HDBK 217F, 25ºC, Gnd Benign Min. 3.5 Typ. Max. Units MHours Reliability Speciﬁcations Parameter T: (781) 344-8226 MTBF F: (781) 344-8481 Safety Standards E: sales@micropowerdirect.com W: www.micropowerdirect.com Safety Approvals UL 1950, EN 60950, IEC 60950 UL, cUL; File No. E245422 Conditions 3.3 VDC Input 5 VDC Input 12 VDC Input 1.5 mm From Case For 10 Sec All Models Min. -0.7 -0.7 -0.7 Typ. Max. 7.0 7.0 15.0 260.0 450 ºC mW VDC Units Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Model Selection Guide Model Number LF101ES LF102ES LF103ES LF104ES LF109ES LF111ES LF112ES LF113ES LF114ES LF151ES LF152ES LF153ES LF159ES Input Output Load Voltage (VDC) Current (mA) Voltage Current Current Regulation Nominal Range Full-Load No-Load (VDC) (mA, Max) (mA, Min) (%, Max) 5 4.5 - 5.5 260 30 5.0 200.0 20.0 15.0 5 4.5 - 5.5 263 30 9.0 111.0 23.0 9.0 5 4.5 - 5.5 253 30 12.0 84.0 17.0 7.5 5 4.5 - 5.5 256 30 15.0 67.0 13.0 7.0 5 4.5 - 5.5 277 30 3.3 300.0 30.0 15.0 12 10.8 - 13.2 121 15 5.0 200.0 20.0 15.0 12 10.8 - 13.2 114 15 9.0 111.0 23.0 9.0 12 10.8 - 13.2 114 15 12.0 84.0 17.0 7.5 12 10.8 - 13.2 113 15 15.0 67.0 13.0 7.0 3.3 3.0 - 3.6 409 55 5.0 200.0 20.0 15.0 3.3 3.0 - 3.6 446 55 9.0 111.0 23.0 9.0 3.3 3.0 - 3.6 433 55 12.0 84.0 17.0 7.5 3.3 3.0 - 3.6 415 55 3.3 300.0 30.0 15.0 Efﬁciency (%, Typ) 77 76 79 78 72 69 73 73 74 74 68 70 73 Fuse Rating Slow-Blow (mA) 500 500 500 500 500 200 200 200 200 750 750 750 750 Other input/output combinations are available (i.e. 24 VDC Input). Contact the factory for details at: sales@micropowerdirect.com Notes: 1. Output load regulation is speciﬁed for a load change of 10% to 100%. 2. When measuring output ripple, it is recommended that an external 0.33 µF ceramic capacitor be placed from the +Vout pin to the -Vout pin. 3. During operation, care must be taken not to exceed the speciﬁed input range of the unit or to allow the output load to drop below the speciﬁed minimum (10% of full load). Operating the unit under either of these conditions could cause damage to the unit. 4. These converters are speciﬁed for operation without external components. However, in some applications the addition of input/output capacitors will enhance stability and reduce output ripple. Recommended capacitor values are: Vin 3.3 VDC 5 VDC 12 VDC Input Capacitor 4.7 µF 4.7 µF 2.2 µF Vout 3.3 VDC 5 VDC 9 VDC 12 VDC 15 VDC Output Capacitor 10.0 µF 10.0 µF 4.7 µF 2.2 µF 1.0 µF Derating Curve Pin Connections Pin Description 1 -Vin 2 +Vin 3 NC 4 -Vout NC = No Connection Pin 5 6 7 8 Description +Vout NC NC NC Recommended Solder Proﬁle For applications requiring very low output noise levels, a simple LC ﬁlter should be effective. 5. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Mechanical Dimensions Board Layout MicroPower Direct www.micropowerdirect.com • Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) • Pin 1 is marked by a “dot” or indentation on the unit 292 Page Street Ste D Stoughton, MA 02072 TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com

下载 PDF

LF152ES

1. 物料型号：LF100ES Series。

2. 器件简介：LF100ES系列是低成本、单输出1W超小型表面贴装DC/DC转换器，具有1W输出功率、超小型SMT封装、UL认证（文件E245422）、单输出、低0.246”高度、1,000 VDC隔离、>3.5 MHour MTBF等特点，支持3.3V、5V和12V输入。

3. 引脚分配： - 1：-Vin（负输入） - 2：+Vin（正输入） - 3：NC（无连接） - 4：-Vout（负输出） - 5：+Vout（正输出） - 6、7、8：NC（无连接）

4. 参数特性： - 输入电压范围：3.3VDC输入3.0-3.6VDC，5VDC输入4.5-5.5VDC，12VDC输入10.8-13.2VDC。 - 反向极性输入电流：1.0A。 - 输出电压精度：±3.0%。 - 线路调整率：3.3V输出为±1.5%，其他输出为±1.2%。 - 负载调整率：根据型号选择指南。 - 纹波和噪声（20MHz）：50mVP-P至100mVP-P。 - 温度系数：±0.03%/°C。 - 输出短路：短暂（0.5秒）。

5. 功能详解：该系列转换器提供稳定的DC/DC转换功能，具有超小型封装和高可靠性，适用于需要小型化和高效率的电源转换场合。

6. 应用信息：适用于需要1W输出功率的场合，如便携式电子设备、通信设备等。

7. 封装信息：封装尺寸为0.50x0.29x0.24英寸（12.7x7.5x6.0mm），封装材料为非导电黑色塑料（UL94-V0），重量为0.05盎司（1.5克）。

LF152ES 价格&库存

-> 查询更多价格&库存

很抱歉，暂时无法提供与“LF152ES”相匹配的价格&库存，您可以联系我们找货

免费人工找货

搜索历史

LF152ES

相关技术文章