LF204ES

LF200ES Series Low Cost, 2W SMT Single Output DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: • 2W Output Power • Ultra-Miniature SMT Case • 1,000 VDC Isolation • -40ºC to +85ºC Operation • Single Output • Low 0.24” Profile • >3.5 MHour MTBF • Industry Standard Pin-Out • LOWEST COST! Input Parameter Input Voltage Range Reverse Polarity Input Current Input Filter Capacitor Conditions For Vin Change of 1% For Iout = 10% to 100% ±8 75 150 Momentary (0.5 Sec.) Conditions 60 Seconds 500 VDC 100 kHz, 1V Min. 1,000 1,000 70 100 Conditions Ambient Min. -40 -55 Free Air Convection RH, Non-condensing 95 % Typ. +25 Max. +85 +125 Typ. Max. Units VDC M pF kHz Units ºC ºC Min. Typ. ±3.0 ±1.2 ±15 150 250 ±0.03 Max. Units % % % mV P - P mV P - P %/ºC Conditions 5 VDC Input 12 VDC Input Min. 4.5 10.8 Typ. 5.0 12.0 Max. 5.5 13.2 1.0 Units VDC A Output Parameter Output Voltage Accuracy Line Regulation Load Regulation Output Ripple (20 MHz) Output Noise (20 MHz) Temperature Coefficient Output Short Circuit General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Environmental Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Physical Case Size Case Material 0.70 x 0.72 x 0.24 Inches (17.78 x 18.03 x 6.0 mm) Non-Conductive Black Plastic (UL94-V0) 0.05 Oz (1.5g) Conditions MIL HDBK 217F, 25ºC, Gnd Benign Conditions 5 VDC Input 12 VDC Input 1.5 mm From Case For 10 Sec All Models Min. 3.5 Min. -0.7 -0.7 Typ. Max. 7.0 15.0 260.0 450 Typ. Max. Units MHours Units VDC ºC mW MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com Weight Reliability Specifications Parameter MTBF Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. www.micropowerdirect.com Model Selection Guide Input Model Number LF201ES LF202ES LF203ES LF204ES LF211ES LF212ES LF213ES LF214ES Voltage (VDC) Nominal 5 5 5 5 12 12 12 12 Range 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 Current (mA) Full-Load 494 487 477 475 203 201 197 196 No-Load 30 30 30 30 15 15 15 15 Voltage (VDC) 5.0 9.0 12.0 15.0 5.0 9.0 12.0 15.0 www.micropowerdirect.com Output Current (mA, Max) 400.0 222.0 167.0 133.0 400.0 222.0 167.0 133.0 Current (mA, Min) 40.0 23.0 17.0 14.0 40.0 23.0 17.0 14.0 Efficiency (%, Typ) 81 82 84 84 82 83 85 85 Fuse Rating Slow-Blow (mA) 500 500 500 500 200 200 200 200 Notes: 1. Output load regulation is specified for a load change of 10% to 100%. 2. When measuring output ripple, it is recommended that an external 0.33 µF ceramic capacitor be placed from the +Vout pin to the -Vout pin. 3. During operation, care must be taken not to exceed the specified input range of the unit or to allow the output load to drop below the specified minimum (10% of full load). Operating the unit under either of these conditions could cause damage to the unit. 4. These converters are specified for operation without external components. However, in some applications the addition of input/output capacitors will enhance stability and reduce output ripple. Recommended capacitor values are: Derating Curve Vin 5 VDC 12 VDC Input Capacitor 4.7 µF 2.2 µF Vout 5 VDC 9 VDC 12 VDC 15 VDC Output Capacitor 4.7 µF 2.2 µF 1.0 µF 0.47 µF For applications requiring very low output noise levels, a simple LC filter should be effective. 5. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Pin Connections Pin 1 2 3 5 6 7 Function Pin Function -Vin 8 NC +Vin 9 NC NC 10 NC NC 12 NC -Vout 13 NC +Vout 14 NC NC = No Connection Recommended Solder Profile Mechanical Dimensions Board Layout Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) • Pin 1 is marked by a “dot” or indentation on the unit MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com