LF217RW

LF200RW Series Miniature SMT, 2W Wide Input Range DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: • 2W Output Power • 2:1 Input Voltage Range • 1,500 VDC Isolation • Short Circuit Protected • Miniature SMT Package • Single & Dual Outputs • 1.0 MH MTBF • Industry Standard Pin-Out Input Parameter Input Start Voltage Input Filter Reverse Polarity Input Current Short Circuit Input Power Conditions 5 VDC Input 12 VDC Input 24 VDC Input 48 VDC Input Min. 3.5 4.5 8.0 16.0 π (Pi) Filter Typ. 4.0 7.0 12.0 24.0 Max. 4.5 9.0 18.0 36.0 1.0 1,500 Conditions Min. Typ. ±1.0 ±1.0 ±0.3 ±0.5 30 Max. ±2.0 ±2.0 ±0.5 ±0.75 50 75 15 300 ±5.0 ±0.02 Units VDC A mW Units % % % % mV P - P mV P - P mV rms % µSec % %/°C Output Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation Ripple & Noise (20 MHz) (Note 1) Ripple & Noise (20 MHz) Ripple & Noise (20 MHz) Output Power Protection Transient Response Time (Note 2) Transient Response Deviation Temperature Coefficient Output Short Circuit Vin = Min to Max Iout = 25% to 100% Over Line, Load & Temp. 120 50% Load Step Change Continuous Conditions 60 Seconds Flash Tested For 1 Sec 1,000 VDC 100 kHz, 1V Min. 1,500 1,650 1,000 RoHS Compliant 100 ±3.0 ±0.01 General Parameter Isolation Voltage Isolation Test Voltage Isolation Resistance Isolation Capacitance Switching Frequency Typ. Max. Units VDC VDC MΩ pF kHz Units °C °C °C % 250 300 420 Environmental Parameter Operating Temperature Range Operating Temperature Range Storage Temperature Range Cooling Humidity Conditions Ambient Case Min. Typ. -40 +25 -40 +25 -40 Free Air Convection RH, Non-condensing Max. +65 +90 +125 95 MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com Physical Case Size Case Material Weight 0.94 x 0.54 x 0.30 Inches (23.8 x 13.7 x 7.62 mm) Non-Conductive Black Plastic (UL94-V0) 0.18 Oz (5.1g) Conditions MIL HDBK 217F, 25°C, Gnd Benign Conditions 5 VDC Input 12 VDC Input 24 VDC Input 48 VDC Input 1.5 mm From Case For 10 Sec All Models Min. 1,000 Min. -0.7 -0.7 -0.7 -0.7 Typ. Max. Units kHours Units VDC °C mW Reliability Specifications Parameter MTBF Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation Typ. Max. 11.0 25.0 50.0 100.0 260 1,800 Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Model Selection Guide Model Number LF201RW LF202RW LF203RW LF204RW LF205RW LF206RW LF207RW LF211RW LF212RW LF213RW LF214RW LF215RW LF216RW LF217RW LF221RW LF222RW LF223RW LF224RW LF225RW LF226RW LF227RW LF231RW LF232RW LF233RW LF234RW LF235RW LF236RW LF237RW Input Output Reflected Efficiency Voltage (VDC) Current (mA) Ripple Voltage Current Current (%, Typ) Nominal Range Full-Load No-Load (VDC) (mA, Max) (mA, Min) Current (mA) 5 4.5 - 9.0 471 40 3.3 500.0 125.0 100 70 5 4.5 - 9.0 548 40 5.0 400.0 100.0 100 73 5 4.5 - 9.0 534 40 12.0 167.0 42.0 100 75 5 4.5 - 9.0 582 40 15.0 134.0 33.0 100 73 5 4.5 - 9.0 667 40 ±5.0 ±200.0 ±50.0 100 64 5 4.5 - 9.0 615 40 ±12.0 ±83.0 ±21.0 100 69 5 4.5 - 9.0 598 40 ±15.0 ±67.0 ±17.0 100 71 12 9.0 - 18.0 184 20 3.3 500.0 125.0 25 73 12 9.0 - 18.0 217 20 5.0 400.0 100.0 25 77 12 9.0 - 18.0 209 20 12.0 167.0 42.0 25 80 12 9.0 - 18.0 220 20 15.0 134.0 33.0 25 80 12 9.0 - 18.0 242 20 ±5.0 ±200.0 ±50.0 25 73 12 9.0 - 18.0 224 20 ±12.0 ±83.0 ±21.0 25 78 12 9.0 - 18.0 226 20 ±15.0 ±67.0 ±17.0 25 78 24 18.0 - 36.0 96 10 3.3 500.0 125.0 15 72 24 18.0 - 36.0 109 10 5.0 400.0 100.0 15 77 24 18.0 - 36.0 109 10 12.0 167.0 42.0 15 80 24 18.0 - 36.0 108 10 15.0 134.0 33.0 15 81 24 18.0 - 36.0 119 10 ±5.0 ±200.0 ±50.0 15 74 24 18.0 - 36.0 112 10 ±12.0 ±83.0 ±21.0 15 78 24 18.0 - 36.0 110 10 ±15.0 ±67.0 ±17.0 15 80 48 36.0 - 72.0 49 8 3.3 500.0 125.0 10 71 48 36.0 - 72.0 57 8 5.0 400.0 100.0 10 73 48 36.0 - 72.0 53 8 12.0 167.0 42.0 10 79 48 36.0 - 72.0 55 8 15.0 134.0 33.0 10 79 48 36.0 - 72.0 62 8 ±5.0 ±200.0 ±50.0 10 71 48 36.0 - 72.0 57 8 ±12.0 ±83.0 ±21.0 10 77 48 36.0 - 72.0 57 8 ±15.0 ±67.0 ±17.0 10 77 Fuse Rating Slow-Blow (mA) 1,000 1,000 1,000 1,000 1,000 1,000 1,000 500 500 500 500 500 500 500 250 250 250 250 250 250 250 120 120 120 120 120 120 120 Notes: 1. When measuring output ripple, it is recommended that an external 0.47 µF ceramic capacitor be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. For noise sensitive applications, the use of 3.3 µF capacitors will reduce the output ripple. 2. Transient recovery is measured to within a 1% error band for a load step change of 75% to 100%. 3. Operation at no-load will not damage these units. However, they may not meet all specifications. 4. Dual output units may be connected to provide a 10 VDC, 24 VDC or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common. 5. The converter should be connected to a low ac-impedance source. An input source with a highly inductive impedance may affect the stability of the converter. In applications where the converter output loading is high and input power is supplied over long lines, it may be necessary to use a capacitor on the input to insure start-up. In this case, it is recommended that a low ESR (ESR