MPE-150S-24

厂商：
MPD
封装：
描述：
MPE-150S-24 - Single Output, 150W Compact, Enclosed AC/DC Power Supplies - MicroPower Direct, LLC

数据手册：

下载MPE-150S-24.pdf

立即购买

详情介绍
数据手册
价格&库存

MPE-150S-24 数据手册

MPE-150S Series Si l O Single Output, 150W 0 Compact, Enclosed AC/DC Power Supplies Electrical Speciﬁcations Key Features: • 150W Output Power • Selectable 88-264 AC Input • EN 60950 Compliant • Eight Single Output Models • Meets EN55022 • >285 kHour MTBF • Compact Metal Enclosure Speciﬁcations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Speciﬁcations subject to change without notice. Input Parameter Input Voltage Range Input Frequency Input Current Inrush Current Safety Ground Leakage Current Conditions Min. Typ. 88 115 176 220 248 47 See Model Selection Guide Cold Start, 115 VAC 17.0 Cold Start, 230 VAC 35.0 115 VAC 230 VAC Switch Selectable Max. 132 264 370 63 Units VAC VDC Hz A Pk 1.5 3.5 Max. mA Units Output Parameter Output Voltage Output Current Output Voltage Adjustment Output Voltage Tolerance, See Note 1 Ripple & Noise (20 MHz), See Note 2 Hold-Up Time Set-Up Time Rise Time Temperature Coefﬁcient Short Circuit Protection Over Voltage Protection Overload Protection Conditions Min. Typ. See Model Selection Guide See Model Selection Guide See Model Selection Guide See Model Selection Guide See Model Selection Guide 115 VAC 20 230 VAC 28 230 VAC 100 230 VAC 50 ±0.02 Continuous (Autorecovery) See Note 3 115 See Note 4 110 Conditions Input to Output Input to Ground Output to Ground 500 VDC Conducted Electrostatic Discharge (ESD) RF Field Susceptibility Electrical Fast Transients/Bursts On Mains Surge Min. 3,000 1,500 500 Typ. RoHS Compliant mSec mSec mSec %/°C 135 160 Max. Units VAC General Parameter Isolation Voltage Isolation resistance EMI/RFI EMC Compliance Switching Frequency MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com 100 MΩ EN 55022; EN 61000-3-2, -3 IEC/EN 61000-4-2, -6, -8, -11 IEC/EN61000-4-3 IEC/EN 61000-4-4 IEC/EN 61000-4-5 25 kHz Units °C °C % Environmental Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Conditions Min. Typ. Max. -10 +25 +60 -20 +85 Free Air Convection (See Derating Curve) RH, Non-condensing 95 Ambient Physical Case Size Case Material Weight 7.83 x 4.33 x 1.97 Inches (199.0 x 110.0 x 50.0 mm) Vented Metal Enclosure 28.3 Oz (0.8 kg) Conditions Min. Typ. Max. Units MIL HDBK 217F, 25°C, Gnd Benign 285 kHours IEN 60950, IEC 60950 10~500 Hz, 2G 10 min/1 Cycle. Period of 60 min each along X, Y &Z Axis Reliability Speciﬁcations Parameter MTBF Safety Standards Vibration Model Selection Guide Model Number MPE-150S-05 MPE-150S-09 MPE-150S-12 MPE-150S-13.5 MPE-150S-15 MPE-150S-24 MPE-150S-27 MPE-150S-48 Input Current (A) 115 VAC 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 230 VAC 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 Output Voltage (VDC) Rated 5.0 9.0 12.0 13.5 15.0 24.0 27.0 48.0 Adjust 4.5 - 5.5 8.0 - 10.4 10.6 - 13.2 12.0 - 15.0 13.5 - 16.5 21.0 - 28.0 24.0 - 30.0 43.0 - 53.0 Current (A) Rated 30.0 16.7 12.5 11.2 10.0 6.5 5.6 3.2 Range 0 to 30.0 0 to 16.7 0 to 12.5 0 to 11.2 0 to 10.0 0 to 6.5 0 to 5.6 0 to 3.2 Output Tolerance (%) ±2.0 ±1.0 ±1.0 ±1.0 ±1.0 ±1.0 ±1.0 ±1.0 Ripple & Noise (mV p-p) Efﬁciency (%, Typ) 150 180 180 180 180 240 240 240 78 80 82 83 84 85 86 87 Notes: 1. Output voltage tolerance includes the the effects of set point accuracy, line regulation and load regulation. 2. Ripple and noise is measured at 20 MHz bandwidth using a 12 inch twisted pair wire to connect to the power supply terminals. A 0.1 µF and a 47 µF capacitor are connected in parallel as close to the power supply terminals as possible. 3. The overvoltage protection circuit shuts down the output. The unit must be repowered to recover once the fault condition is removed. 4. The overload protection circuit shuts down the output. The unit must be repowered to recover once the fault condition is removed. 5. Efﬁciency is measured with a 115 VAC input. 6. It is recommended that a fuse be used on the input of a power supply for protection. For the MPE-150S series, a 7.5A/250 VAC slow blow should be used. Mechanical Dimensions Pin Connections Pin 1 2 3 4 5 6 7 Function AC-Line AC-Neutral AC-Ground -Vout -Vout +Vout +Vout Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) Derating Curve Static Characteristics (24 Vout) MicroPower Direct www.micropowerdirect.com • 292 Page Street Ste D Stoughton, MA 02072 TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com

下载 PDF

MPE-150S-24

### 物料型号： - 型号系列为MPE-150S，具体型号包括MPE-150S-05、MPE-150S-09、MPE-150S-12、MPE-150S-13.5、MPE-150S-15、MPE-150S-24、MPE-150S-27和MPE-150S-48。

### 器件简介： - MPE-150S系列电源供应器提供150W输出功率，具有可选的88-264V AC输入，符合EN 60950标准，有八种单一输出模型，满足EN55022标准，MTBF超过285,000小时，采用紧凑金属外壳。

### 引脚分配： - 引脚1：AC-Line（交流输入火线） - 引脚2：AC-Neutral（交流输入零线） - 引脚3：AC-Ground（交流输入地线） - 引脚4：-Vout（负输出） - 引脚5：-Vout（负输出） - 引脚6：+Vout（正输出） - 引脚7：+Vout（正输出）

### 参数特性： - 输入电压范围：88-264VAC或176-370VDC，输入频率47-63Hz。 - 输出电压和电流根据具体型号有所不同，输出电压调整和容差也因型号而异。 - 纹波和噪声（20MHz）根据型号不同而有所变化。 - 保持时间在115VAC和230VAC下分别为20ms和28ms。

### 功能详解： - 过压保护和过载保护会关闭输出，需要重新上电才能恢复。 - 短路保护为连续型（自动恢复）。 - 隔离电压和隔离电阻满足特定的安全标准。 - EMI/RFI符合EN 55022和EN 61000-3-2、-3标准。 - 抗静电放电（ESD）符合IEC/EN 61000-4-2标准。

### 应用信息： - 适用于需要高效率、高可靠性的电源解决方案的应用场合。

### 封装信息： - 外壳尺寸为7.83 x 4.33 x 1.97英寸（199.0x110.0x50.0毫米），材料为通风金属外壳，重量为28.3盎司（0.8公斤）。

MPE-150S-24 价格&库存

-> 查询更多价格&库存

很抱歉，暂时无法提供与“MPE-150S-24”相匹配的价格&库存，您可以联系我们找货

免费人工找货

搜索历史

MPE-150S-24

相关技术文章