MPE-320S-15

MPE-320S Series Si l O Single Output, 320W 320 Compact, Enclosed AC/DC Power Supplies Electrical Specifications Key Features: • 320W Output Power • Selectable 88-264 AC Input • EN 60950 Approved • Internal Fan With Control • Eight Single Output Models • Meets EN55022 • >188 kHour MTBF • Compact Metal Enclosure Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Parameter Input Voltage Range Input Frequency Input Current Inrush Current Safety Ground Leakage Current Conditions Min. Typ. 88 115 Switch Selectable 176 220 248 47 See Model Selection Guide Cold Start, 115 VAC 20.0 Cold Start, 230 VAC 40.0 115 VAC 230 VAC Max. 132 264 370 63 Units VAC VDC Hz A Pk 2.0 3.5 mA Units Output Parameter Output Voltage Output Current Output Voltage Adjustment Output Voltage Tolerance, See Note 1 Ripple & Noise (20 MHz), See Note 2 Hold-Up Time Conditions Min. Typ. Max. See Model Selection Guide See Model Selection Guide See Model Selection Guide See Model Selection Guide See Model Selection Guide 115 VAC 20 230 VAC 24 230 VAC 2,000 230 VAC 20 ±0.02 Continuous (Autorecovery) See Note 3 115 135 See Note 4 105 135 Fan On, 5V - 15 Vout RT1 >65 °C Fan On, 24V - 48 Vout RT1 >70 °C Fan Off, 5V - 15 Vout RT1 80 °C Conditions Input to Output Input to Ground Output to Ground 500 VDC Conducted Electrostatic Discharge (ESD) RF Field Susceptibility Electrical Fast Transients/Bursts On Mains Surge Min. 3,000 1,500 500 Typ. Max. mSec mSec mSec %/°C % % RoHS Compliant Set-Up Time Rise Time Temperature Coefficient Short Circuit Protection Over Voltage Protection Overload Protection Fan Control (Over Temp Control) General Parameter Isolation Voltage Units VAC 100 MΩ EN 55022; EN 61000-3-2, -3 IEC/EN 61000-4-2, -6, -8, -11 IEC/EN61000-4-3 IEC/EN 61000-4-4 IEC/EN 61000-4-5 75 kHz Units °C °C % MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com Isolation resistance EMI/RFI EMC Compliance Switching Frequency Environmental Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Conditions Min. Typ. Max. -10 +25 +60 -20 +85 Internal Fan With Built In Control RH, Non-condensing 95 Ambient Physical Case Size Case Material Weight 8.46 x 4.52 x 1.97 Inches (215.0 x 115.0 x 50.0 mm) Vented Metal Enclosure 38.1 Oz (1.08 kg) Conditions Min. Typ. Max. Units MIL HDBK 217F, 25°C, Gnd Benign 188 kHours IEN 60950, IEC 60950 10~500 Hz, 2G 10 min/1 Cycle. Period of 60 min each along X, Y &Z Axis Reliability Specifications Parameter MTBF Safety Standards Vibration Model Selection Guide Model Number MPE-320S-05 MPE-320S-7.5 MPE-320S-12 MPE-320S-13.5 MPE-320S-15 MPE-320S-24 MPE-320S-27 MPE-320S-48 Input Current (A) 115 VAC 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 230 VAC 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 Output Voltage (VDC) Rated 5.0 7.5 12.0 13.5 15.0 24.0 27.0 48.0 Adjust 4.5 - 5.7 6.0 - 9.0 10.0 - 13.2 12.0 - 15.0 13.5 - 18.0 20.0 - 26.4 26.0 - 32.0 41.0 - 56.0 Current (A) Rated 50.0 36.0 25.0 22.0 20.0 12.5 11.0 6.5 Range 0 to 50.0 0 to 36.0 0 to 25.0 0 to 22.0 0 to 20.0 0 to 12.5 0 to 11.0 0 to 6.5 Output Tolerance (%) ±2.0 ±2.0 ±1.0 ±1.0 ±1.0 ±1.0 ±1.0 ±1.0 Ripple & Noise (mV p-p) Efficiency (%, Typ) 150 150 150 150 150 150 200 240 77 80 82 83 84 86 86 87 Notes: 1. Output voltage tolerance includes the the effects of set point accuracy, line regulation and load regulation. 2. Ripple and noise is measured at 20 MHz bandwidth using a 12 inch twisted pair wire to connect to the power supply terminals. A 0.1 µF and a 47 µF capacitor are connected in parallel as close to the power supply terminals as possible. 3. Overvoltage protection is provided by a “hiccup mode” circuit. The unit recovers automatically when the fault condition is removed. 4. Overload protection is provided by foldback current limiting. The unit recovers automatically when the fault condition is removed. 5. It is recommended that a fuse be used on the input of a power supply for protection. For the MPE-320S series, a 10A/250 VAC slow blow should be used. Mechanical Dimensions Pin Connections Pin 1 2 3 4 5 6 7 8 9 Function AC-Line AC-Neutral AC-Ground -Vout -Vout -Vout +Vout +Vout +Vout Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) Derating Curve Static Characteristics MicroPower Direct www.micropowerdirect.com • 292 Page Street Ste D Stoughton, MA 02072 TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com