MPO-45S-13.5

厂商：
MPD
封装：
描述：
MPO-45S-13.5 - Single Output, 45W Compact, Open Frame AC/DC Power Supplies - MicroPower Direct, LLC

数据手册：

下载MPO-45S-13.5.pdf

立即购买

详情介绍
数据手册
价格&库存

MPO-45S-13.5 数据手册

MPO-45S Series Si l O Single Output, 45W Compact, Open Frame AC/DC Power Supplies Electrical Speciﬁcations Key Features: • 45W Output Power • Universal 90-264 AC Input • EN 60950 Compliant • Low Leakage Current • Nine Single Output Models • Meets EN55022 • >300 kHour MTBF • Only 5” x 3” x 1.1” Speciﬁcations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Speciﬁcations subject to change without notice. Input Parameter Input Voltage Range Input Frequency Input Current Inrush Current Safety Ground Leakage Current Conditions Min. Typ. 90 127 47 See Model Selection Guide Cold Start, 115 VAC 15.0 Cold Start, 230 VAC 30.0 115 VAC 0.5 240 VAC 0.75 Universal Max. 264 370 63 Units VAC VDC Hz A Pk mA Max. Units Output Parameter Output Voltage Output Current Output Voltage Adjustment Output Voltage Tolerance, See Note 1 Ripple & Noise (20 MHz), See Note 2 Hold-Up Time Set-Up Time Rise Time Temperature Coefﬁcient Short Circuit Protection Over Voltage Protection Overload Protection Conditions Min. Typ. See Model Selection Guide See Model Selection Guide See Model Selection Guide See Model Selection Guide See Model Selection Guide 115 VAC 15 230 VAC 60 230 VAC 800 230 VAC 30 ±0.02 Continuous (Autorecovery) See Note 3 115 See Note 4 118 Conditions Input to Output Input to Ground Output to Ground 500 VDC Conducted Electrostatic Discharge (ESD) RF Field Susceptibility Electrical Fast Transients/Bursts On Mains Surge Fixed Conditions Min. 3,000 1,500 500 Typ. mSec mSec mSec %/°C 135 166 Max. % % Units VAC RoHS Compliant General Parameter Isolation Voltage Isolation resistance EMI/RFI MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com EMC Compliance Switching Frequency 100 MΩ EN 55022; EN 61000-3-2, -3 IEC/EN 61000-4-2, -6, -8, -11 IEC/EN61000-4-3 IEC/EN 61000-4-4 IEC/EN 61000-4-5 65 kHz Units °C °C % Environmental Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Min. Typ. Max. -10 +25 +60 -20 +85 Free Air Convection (See Derating Curve) RH, Non-condensing 95 Ambient Physical Size Weight 5.00 x 3.00 x 1.10 Inches (127.0 x 76.2 x 28.0 mm) 6.7 Oz (0.19 kg) Conditions Min. Typ. Max. Units MIL HDBK 217F, 25°C, Gnd Benign 300 kHours IEN 60950, IEC 60950 10~500 Hz, 2G 10 min/1 Cycle. Period of 60 min each along X, Y &Z Axis Reliability Speciﬁcations Parameter MTBF Safety Standards Vibration Model Selection Guide Model Number MPO-45S-3.3 MPO-45S-05 MPO-45S-7.5 MPO-45S-12 MPO-45S-13.5 MPO-45S-15 MPO-45S-24 MPO-45S-27 MPO-45S-48 Input Current (A) 115 VAC 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 230 VAC 0.56 0.56 0.56 0.56 0.56 0.56 0.56 0.56 0.56 Output Voltage (VDC) Rated 3.3 5.0 7.5 12.0 13.5 15.0 24.0 27.0 48.0 Adjust 3.14 - 3.63 4.75 - 5.5 7.13 - 8.25 11.4 - 13.2 12.8 - 14.85 14.25 - 16.5 22.8 - 26.4 25.65 - 29.7 45.6 - 52.8 Current (A) Rated 8.0 8.0 5.4 3.7 3.3 3.0 1.9 1.7 1.0 Range 0 to 10.7 0 to 10.5 0 to 7.0 0 to 4.4 0 to 3.9 0 to 3.5 0 to 2.2 0 to 1.95 0 to 1.1 Output Tolerance (%) ±3.0 ±3.0 ±3.0 ±2.0 ±2.0 ±2.0 ±2.0 ±2.0 ±2.0 Ripple & Noise (mV p-p) Efﬁciency (%, Typ) 80 100 100 100 100 100 100 100 100 69 74 75 76 77 77 78 78 78 Notes: 1. Output voltage tolerance includes the the effects of set point accuracy, line regulation and load regulation. 2. Ripple and noise is measured at 20 MHz bandwidth using a 12 inch twisted pair wire to connect to the power supply terminals. A 0.1 µF and a 47 µF capacitor are connected in parallel as close to the power supply terminals as possible. 3. Overvoltage protection is provided by a “hiccup mode” circuit. The unit recovers automatically when the fault condition is removed. 4. Overload protection is provided by a foldback current limiting circuit. The unit recovers automatically when the fault condition is removed. For the 3.3V output model, overload protection is set to operate between 36 to 55W. 5. Mounting holes M1 and M2 should be grounded for EMI purposes. 6. It is recommended that a fuse be used on the input of a power supply for protection. See the mechanical diagram for the correct rating. Mechanical Dimensions Pin Connections: CN1 (Molex 5277-02 or equiv.) Pin 1 2 Function Mating Housing Terminal AC-Neutral Molex 5195 Molex 5194 or Equiv. or Equiv. AC-Line Pin Connections: CN2 (Molex 5273-06 or equiv.) Pin 1, 2, 3 4, 5, 6 Function +Vout -Vout Mating Housing Terminal Molex 5195 Molex 5194 or Equiv. or Equiv. Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) Derating Curve Static Characteristics MicroPower Direct www.micropowerdirect.com • 292 Page Street Ste D Stoughton, MA 02072 TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com

下载 PDF

MPO-45S-13.5

物料型号： - 型号编号包括MPO-45S-3.3、MPO-45S-05、MPO-45S-7.5、MPO-45S-12、MPO-45S-13.5、MPO-45S-15、MPO-45S-24、MPO-45S-27、MPO-45S-48。

器件简介： - MPO-45S系列是单输出45W硅IP紧凑开放式AC/DC电源，具有90-264VAC通用输入，符合EN60950标准，低漏电流，九种单输出型号，满足EN55022标准，MTBF超过300,000小时，尺寸仅5" x 3" x 1.1"。

引脚分配： - CN1（Molex 5277-02或等效）： - 引脚1：AC-Neutral - 引脚2：AC-Line - CN2（Molex 5273-06或等效）： - 引脚1、2、3：+Vout - 引脚4、5、6：-Vout

参数特性： - 输入电压范围：90-264VAC（通用输入），127-370VDC。 - 输入频率：47-63Hz。 - 输出电压和电流：根据型号选择指南确定。 - 输出电压调整：根据型号选择指南确定。 - 输出电压容差：见型号选择指南。 - 纹波和噪声（20MHz）：见型号选择指南。 - 保持时间：60ms。 - 设置时间：800ms。 - 上升时间：30ms。 - 温度系数：±0.02%/°C。 - 短路保护：连续（自动恢复）。 - 过压保护：具备。 - 过载保护：见型号选择指南。

功能详解： - 纹波和噪声是在20MHz带宽下使用12英寸双绞线连接到电源端子测量的，尽可能靠近电源端子并联连接0.1μF和47μF电容器。 - 过压保护由“打嗝模式”电路提供，当故障条件移除时单元自动恢复。 - 过载保护由折叠式电流限制电路提供，当故障条件移除时单元自动恢复。对于3.3V输出型号，过载保护设置在36至55W之间操作。

应用信息： - 该系列产品适用于需要高效率、高可靠性的电源解决方案的应用，如工业控制系统、通信设备、测试和测量设备等。

封装信息： - 尺寸：5.00 x 3.00 x 1.10英寸（127.0 x 76.2 x 28.0毫米）。 - 重量：6.7盎司（0.19千克）。

MPO-45S-13.5 价格&库存

-> 查询更多价格&库存

很抱歉，暂时无法提供与“MPO-45S-13.5”相匹配的价格&库存，您可以联系我们找货

免费人工找货

搜索历史

MPO-45S-13.5

相关技术文章