SR7805-09W

SR7805 Series Low Cost, Non-isolated Ultra-Miniature SIP POL Switching Regulators Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: • Efficiency to 96% • Ultra-Miniature SIP Case • LM78xx Replacement • Wide Input Range • Short Circuit Protected • Thermal Shutdown • Low Noise Output Parameter Output Voltage Accuracy Line Regulation Load Regulation Ripple & Noise (20 MHz) Dynamic Load Stability Output Power Protection Thermal Shutdown Quiescent Current Output Current Limit Output Short Circuit Continuous (Autorecovery) See Note 1 See Note 2 Between 10% - 100% Load 120 150 5 7 2,000 Vin = Min to Max Iout = 10% to 100% Conditions Min. Typ. ±2.0 ±0.2 ±0.4 20 Max. ±3.0 ±0.4 ±0.6 35 ±100 Units % % % mV P - P mV % °C mA mA General RoHS Compliant Parameter Isolation Voltage Switching Frequency Conditions Min. Not Isolated 280 Typ. Max. Units 330 450 kHz Environmental Parameter Operating Temperature Range Operating Temperature Range Conditions Ambient Case -55 1.5 mm From Case For 10 Sec Free Air Convection RH, Non-condensing 95 % Min. -40 Typ. +25 Max. +85 +100 +125 300 Units °C °C °C °C MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com Storage Temperature Range Lead Temperature Cooling Humidity Physical Case Size Case Material Weight 0.45 x 0.3 x 0.40 Inches (11.5 x 7.55 x 10.2 mm) Non-Conductive Black Plastic (UL-94V0) 0.07 Oz (2.0g) Reliability Specifications Parameter MTBF Conditions MIL HDBK 217F, 25°C, Gnd Benign Min. 2.0 Typ. Max. Units MHours Model Selection Guide Model Number SR7805-03W SR7805-05W SR7805-06W SR7805-09W SR7805-12W SR7805-15W Input Voltage Range (VDC) 4.75 - 28.0 6.5 - 32.0 8.0 - 32.0 11.0 - 32.0 15.0 - 32.0 18.0 - 32.0 Output Voltage Current (VDC) (mA, Max) 3.3 500.0 5.0 500.0 6.5 500.0 9.0 500.0 12.0 500.0 15.0 500.0 Efficiency (%, Typ) Min Vin 90 93 94 95 95 96 Max Vin 80 84 87 91 92 93 Notes: 1. Dynamic load stability is specified for output loads from 10% to 100%. 2. Quiescent current is specified at 0% load for Vin = min to max. 3. The input should not exceed the range given in the model selection chart above. Exceeding this limit could damage the unit. Mechanical Dimensions Typical Application Circuit Notes: 1. C1 is a low ESR ceramic capacitor used to minimize noise at the regulator. A tantalum or low ESR electrolytic capacitor may also be used. A typical value is 10 µF/50V. 2. C2 is optional. A typical value is a 100 µF/25V electrolytic capacitor. Derating Curve Pin Connections Pin 1 2 3 Description +Vin Gnd +Vout Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) • Pin 1 is marked by a “dot” or indentation on the side of the unit MicroPower Direct www.micropowerdirect.com • 292 Page Street Ste D Stoughton, MA 02072 TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com