EV6619L-Q-00A

EV6619L-Q-00A 2.5V to 28V, 5A, H-Bridge Motor Driver Evaluation Board DESCRIPTION The EV6619L-Q-00A evaluation board is designed to demonstrate the capabilities of the MP6619L, an H-Bridge motor driver. It operates from a supply input voltage (VIN) up to 28V, and can deliver a motor current up to 5A. The MP6619L is typically used to drive a brushed DC motor. The MP6619L has a configurable current limit (ILIMIT). For simplicity, the output polarity can be controlled by pulling the IN1 and IN2 pins high or low. Full protection features include over-current protection (OCP), input over-voltage protection (OVP), under-voltage lockout (UVLO), and thermal shutdown. The input control signals for the MP6619L are applied via the connector or generated on the board. The MP6619L is available in a QFN-19 (3mmx3mm) package. It is recommended to read the MP6619L datasheet prior to making any changes to the EV6619L-Q-00A. PERFORMANCE SUMMARY Parameters Input voltage (VIN) range Maximum output current (IOUT_MAX) VCC voltage (VCC) VDD voltage (VDD) Conditions Value 2.5V to 28V 5A 2.8V to 5.5V 3.3V or 5V EV6619L-Q-00A EVALUATION BOARD LxW (7.5cmx7.5cm) Board Number MPS IC Number EV6619L-Q-00A MP6619LGQ EV6619L-Q-00A Rev. 1.0 MonolithicPower.com 6/29/2022 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2022 MPS. All Rights Reserved. 1 EV6619L-Q-00A – 28V, 5A, H-BRIDGE DRIVER EVALUATION BOARD QUICK START GUIDE 1. Connect the input voltage (2.5V ≤ VIN ≤ 28V) and input ground to the VIN and GND connectors, respectively. 2. Connect the VCC voltage (2.8V ≤ VCC ≤ 5.5V) and ground to the VCC and GND connectors, respectively. 3. Connect the VDD voltage (3.3V or 5V) and ground to the VDD and GND connectors, respectively. 4. Set the input control and logic signal through the CN1 connector via the external MCU, or manually through SW1. Manual action requires an external 3.3V or 5V VDD as a pull-up power supply. Table 1 shows the logic truth table. Table 1: Logic Truth Table EN INx OUTx 0 X (1) Hi-Z 1 0 Low 1 1 High Note: 1) X denotes N/A. 5. The current control trip value is set by the adjustable resistor (R4). When the ISET pin is floating, the current trip voltage (VITRIP) is set to the default (200mV). If a resistor is connected between ISET and GND, then VITRIP can be reduced below 200mV to reduce power loss on the sense resistor. The relationship between VITRIP and the ISET resistor (RISET) can be calculated with Equation (1): VITRIP (V)  0.2  40 RISET  kΩ  (1) 6. The output current limit (IOUT_LIM) is determined by VITRIP and RISEN. If RISET is connected between ISET and ground, then IOUT_LIM can be estimated with Equation (2): IOUT_LIM (A)  0.2  40 1  RISET  kΩ  RISEN  Ω  (2) If ISET remains floating, then IOUT_LIM can be calculated with Equation (3): IOUT_LIM (A)  0.2 RISEN  Ω  EV6619L-Q-00A Rev. 1.0 MonolithicPower.com 6/29/2022 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2022 MPS. All Rights Reserved. (3) 2 EV6619L-Q-00A – 28V, 5A, H-BRIDGE DRIVER EVALUATION BOARD EVALUATION BOARD SCHEMATIC Figure 1: Evaluation Board Schematic EV6619L-Q-00A Rev. 1.0 MonolithicPower.com 6/29/2022 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2022 MPS. All Rights Reserved. 3 EV6619L-Q-00A – 28V, 5A, H-BRIDGE DRIVER EVALUATION BOARD EV6619L-Q-00A BILL OF MATERIALS Qty Ref Value 2 C1, C3 100μF 2 C2, C4 4.7μF 2 C5, C7 100nF 1 C6 1μF 2 C8, C9 100nF 1 2 1 R1 R2, R5 R3 1kΩ 10Ω 40.2kΩ 1 R4 100kΩ 3 1 1 1 R7, R8, R9 R10 LED1 SW1 VDD, VCC, GND1, GND2 VIN1, OUT1, OUT2, GND CN1 J1, J2 nFAULT, GND, ISET, EN, IN2, IN1 4.7kΩ 50mΩ 50mW 25mA 4 4 1 2 6 1 U1 Description Electrolytic capacitor, 35V Ceramic capacitor, 50V, X7R Ceramic capacitor, 50V, X7R Ceramic capacitor, 25V, X7R Ceramic capacitor, 50V, X7R Film resistor, 1% Film resistor, 1% Film resistor, 1% Square trimming potentiometer Film resistor, 5% Film resistor, 1% Red LED Dial switch, 4-bit Package Manufacturer DIP Jianghai CD287-35V100 1210 Murata GRM32ER71H475KA88L 0603 Murata GRM188R71H104KA93D 0805 Murata GRM21BR71E105KA99L 0805 Murata GRM21BR71H104KA01L 0805 0603 0603 Yageo Yageo Yageo RC0805FR-071KL RC0603FR-0710RL RC0603FR-0740K2L DIP Bourns 3266W-1-104LF 0805 3720 0805 SMD Yageo Cyntec Baihong Wurth RC0805JR-074K7L RL3720WT-R050-FN BL-HUE35A-AV-TRB 418121270804 1mm Connector DIP Any 2mm Connector DIP Any 2.54mm 2.54mm Connector, 4-bit Jumper DIP DIP Any Any 1mm Yellow test point DIP Any QFN-19 (3mmx 3mm) MPS MP6619L 2.5V to 28V, 5A, H-bridge motor driver Manufacturer PN MP6619LGQ EV6619L-Q-00A Rev. 1.0 MonolithicPower.com 6/29/2022 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2022 MPS. All Rights Reserved. 4 EV6619L-Q-00A – 28V, 5A, H-BRIDGE DRIVER EVALUATION BOARD PCB LAYOUT Figure 2: Top Silk Figure 3: Top Layer Figure 4: Mid-Layer 1 Figure 5: Mid-Layer 2 EV6619L-Q-00A Rev. 1.0 MonolithicPower.com 6/29/2022 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2022 MPS. All Rights Reserved. 5 EV6619L-Q-00A – 28V, 5A, H-BRIDGE DRIVER EVALUATION BOARD PCB LAYOUT (continued) Figure 6: Bottom Layer Figure 7: Bottom Silk EV6619L-Q-00A Rev. 1.0 MonolithicPower.com 6/29/2022 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2022 MPS. All Rights Reserved. 6 EV6619L-Q-00A – 28V, 5A, H-BRIDGE DRIVER EVALUATION BOARD REVISION HISTORY Revision # 1.0 Revision Date 6/29/2022 Description Initial Release Pages Updated - Notice: The information in this document is subject to change without notice. Users should warrant and guarantee that thirdparty Intellectual Property rights are not infringed upon when integrating MPS products into any application. MPS will not assume any legal responsibility for any said applications. EV6619L-Q-00A Rev. 1.0 MonolithicPower.com 6/29/2022 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2022 MPS. All Rights Reserved. 7