EVQ6610-S-00A

EVQ6610-S-00A 55V, 3A Half-Bridge Power Driver Evaluation Board, AEC-Q100 Qualified DESCRIPTION FEATURES The EVQ6610-S-00A is an evaluation board for the MPQ6610GS, a half-bridge power driver.     The EVQ6610-S-00A operates from a supply voltage of up to 55V, and can deliver load currents up to 3A. The input control signals for the MPQ6610 are either generated on the board, or from an external controller through the board’s connector (P1). The MPQ6610GS is available in an SOIC-8 package. ELECTRICAL SPECIFICATIONS Parameter Input voltage Maximum output current Symbol Value Units VIN 4 to 55 V IOUT-L 3 A     Wide 4V to 55V Input Voltage Range Up to 3A Output Current Internal Current Sense 2.5V, 3.3V, and 5V Compatible Logic Supply Over-Current Protection (OCP), OverVoltage Protection (OVP), OverTemperature Protection (OTP) Fault Indication Output Available in an SOIC-8 Package AEC-Q100 Qualified APPLICATIONS    Solenoid Drivers Brushed DC Motors Relay Drivers All MPS parts are lead-free, halogen-free, and adhere to the RoHS directive. For MPS green status, please visit the MPS website under Quality Assurance. “MPS”, the MPS logo, and “Simple, Easy Solutions” are trademarks of Monolithic Power Systems, Inc. or its subsidiaries. EVQ6610-S-00A EVALUATION BOARD LxW (6.35cmx6.35cm) Board Number MPS IC Number EVQ6610-S-00A MPQ6610GS EVQ6610-S-00A Rev. 1.0 MonolithicPower.com 3/19/2021 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2021 MPS. All Rights Reserved. 1 EVQ6610-S-00A – 55V, HALF-BRIDGE POWER DRIVER EVAL BOARD, AEC-Q100 QUICK START GUIDE 1. Attach the input voltage (4V ≤ VIN ≤ 55V) to the VIN connector, and attach the input ground to the GND connector. 2. Attach the VCC voltage (2.5V, 3.3V, or 5V) to the VCC connector, and attach the input ground to the GND connector. 3. Input control signals can be generated on the board through the placement of short jumpers (JP1 and JP2), or by an external controller connected through the P1 connector. If using an external controller, remove the short jumpers (JP1 and JP2). Table 1 shows the input logic truth table. Table 1: Input Logic Truth Table EN 0 0 1 1 IN 0 1 0 1 OUT Z Z L H 4. The output current limit threshold is reached when the ISET pin reaches 1.5V. The ISET pin voltage scaling is set by the trimming potentiometer (RV1). For example, with a 10kΩ resistor connected from ISET to ground, the ISET pin voltage is 1V for every 1A of output current. This means that when the current reaches 1.5A, the ISET pin voltage reaches 1.5V, and a current trip occurs. EVQ6610-S-00A Rev. 1.0 MonolithicPower.com 3/19/2021 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2021 MPS. All Rights Reserved. 2 EVQ6610-S-00A – 55V, HALF-BRIDGE POWER DRIVER EVAL BOARD, AEC-Q100 EVALUATION BOARD SCHEMATIC VIN VIN_GND OUT LOAD_GND P1 VI N OUT 2 2 VI N C3 100nF/100V GND GND 1 2.2 F/100V 1 C2 C1 100 F/100V EN IN 1 2 FLT GND VCC GND GND VSET ISET nFAULT GND VCC VCC_GND GND GND 2 EN 8 1 2 IN 7 JP2 ISET 6 EN IN OUT BST S ISET nFAU nFAUL F LT 3 OUT 1 1 5 C4 D1 2 1 2 OUT 100nF/25V NS 4 C5 1 U1 MPQ6610GS 1 R2 1k JP1 GND VIN R1 1k 2 VCC VCC 2 100nF/25V R4 4.99k GND GND nFAUL T 1 2 LED1 R3 GND 1k RV1 10k GND Figure 1: Evaluation Board Schematic EVQ6610-S-00A Rev. 1.0 MonolithicPower.com 3/19/2021 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2021 MPS. All Rights Reserved. 3 EVQ6610-S-00A – 55V, HALF-BRIDGE POWER DRIVER EVAL BOARD, AEC-Q100 EVQ6610-S-00A BILL OF MATERIALS Qty Ref Value 1 C1 100μF 1 C2 2.2μF 1 C3 100nF 2 C4, C5 100nF 3 1 R1, R2, R3 R4 1kΩ 4.99kΩ 1 RV1 10kΩ 1 1 LED1 D1 3 2 2 4 3 1 Description 100V electrolytic capacitor 100V ceramic capacitor, X7R 100V ceramic capacitor, X7R 25V ceramic capacitor, X7R Film resistor, 1% Film resistor, 1% Square trimming potentiometer LED Red NS 2 bits/ JP1, JP2, P1 Connector 2.54mm JP1, JP2 2.54mm Short jumper FLT, VSET Yellow Test point VIN, VIN_GND, Connector, 2mm Φ = 2mm OUT, LOAD_GND needle Connector, 1mm VCC, VCC_GND, Φ = 1mm needle GND Half-bridge power U1 55V, 3A driver Package Manufacturer Manufacturer P/N DIP Jianghai CD263-100V100 1210 Murata GRM32ER72A225KA35L 0603 Murata GRM188R72A104KA35D 0603 Murata GRM188R71E104KA01D 0603 0603 Yageo Yageo RC0603FR-071KL RC0603FR-074K99L DIP Bourns 3266W-1-103F 0805 Baihong BL-HUE35A-AV-TRB DIP Any DIP DIP Any Any DIP Any DIP Any SOIC-8 MPS MPQ6610GS EVQ6610-S-00A Rev. 1.0 MonolithicPower.com 3/19/2021 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2021 MPS. All Rights Reserved. 4 EVQ6610-S-00A – 55V, HALF-BRIDGE POWER DRIVER EVAL BOARD, AEC-Q100 PCB LAYOUT Figure 2: Top Silk Layer Figure 3: Top Layer Figure 4: Bottom Layer EVQ6610-S-00A Rev. 1.0 MonolithicPower.com 3/19/2021 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2021 MPS. All Rights Reserved. 5 EVQ6610-S-00A – 55V, HALF-BRIDGE POWER DRIVER EVAL BOARD, AEC-Q100 REVISION HISTORY Revision # 1.0 Revision Date 3/19/2021 Description Initial Release Pages Updated - Notice: The information in this document is subject to change without notice. Please contact MPS for current specifications. Users should warrant and guarantee that third-party Intellectual Property rights are not infringed upon when integrating MPS products into any application. MPS will not assume any legal responsibility for any said applications. EVQ6610-S-00A Rev. 1.0 MonolithicPower.com 3/19/2021 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2021 MPS. All Rights Reserved. 6