MP2481
36V, 1.2A, 1.4MHz
White LED Driver
The Future of Analog IC Technology
DESCRIPTION
FEATURES
The MP2481 is a 36V, 1.2A, white LED driver
suitable for either step-down or inverting
step-up/down applications. It achieves 1.2A
peak output current over a wide input supply
range with excellent load and line regulation.
Current mode operation provides fast transient
response and eases loop stabilization. Fault
condition protection includes thermal shutdown,
cycle-by-cycle peak current limiting, input over
voltage protection, open strings protection and
output short circuit protection.
The MP2481 incorporates both DC and PWM
dimming onto a single control pin. The separate
input reference ground pin allows for direct
enable and/or dimming control for a positive to
negative power conversion.
The MP2481 requires a minimum number of
readily available standard external components
and is available in 8-pin MSOP8E package.
EVALUATION BOARD REFERENCE
Board Number
Mode
EV2481-H-00A
Step-down
EV2481-H-01A
Step-up/down
1.2A Maximum Output Current
Unique Step-up/down Operation (BuckBoost Mode)
Wide 4.5V to 36V Operating Input Range for
Step-Down Applications (Buck Mode)
0.30Ω Internal Power MOSFET Switch
Fixed 1.4MHz Frequency
Analog and PWM Dimming
0.2V Reference Voltage
Up to 95% Efficiency
5μA Shutdown Mode
No minimum LED required
Stable with Low ESR Output Ceramic
Capacitors
Cycle-by-Cycle Over Current Protection
Thermal Shutdown Protection
Open Strings Protection
Input Over Voltage Protection
Output Short Circuit Protection
Available in 8-Pin MSOP8E Package
APPLICATIONS
General LED Illuminations
LCD Backlight Panels
Handheld Computers
Automotive Internal Lighting
Portable Multimedia Players
Portable GPS Devices
All MPS parts are lead-free and adhere to the RoHS directive. For MPS green
status, please visit MPS website under Quality Assurance. “MPS” and “The
Future of Analog IC Technology” are Trademarks of Monolithic Power
Systems, Inc.
TYPICAL APPLICATION (STEP-UP/DOWN APPLICATION)
Efficiency vs. Input Voltage
Step-up/down Application
3
VIN
OVP
VDD
BST
7
90
Cbs
L1
85
SW 6
C1
D1
MP2481
EN/DIM
5 EN/DIM
GND
6 INGND
VSS
2
FB
C2
R1
4
R2
RS
EFFICIENCY (%)
1
4 series,400mA
80
3 series,400mA
75
3 series,9 paralleded,180mA total
70
65
60
0
5
10
15
20
25
30
INPUT VOLTAGE (V)
MP2481 Rev. 1.5
8/24/2020
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2020 MPS. All Rights Reserved.
1
MP2481 –36V, 1.2A, 1.4MHz WHITE LED DRIVER
ORDERING INFORMATION
Part Number*
Package
Top Marking
MP2481DH
MSOP8E
2481D
* For Tape & Reel, add suffix –Z (e.g. MP2481DH–Z).
For RoHS compliant packaging, add suffix –LF (e.g. MP2481DH–LF–Z)
PACKAGE REFERENCE
TOP VIEW
VDD
1
8
SW
VSS
2
7
BST
OVP
3
6
INGND
FB
4
5
EN/DIM
EXPOSED PAD
ON BACK SIDE*
* Do not Connect to Input Ground (INGND)
for Boost, Buck-Boost applications
ABSOLUTE MAXIMUM RATINGS (1)
Thermal Resistance (4)
Supply Voltage VDD – VSS ............................. 40V
VSW – VSS .............................. –0.3V to VIN + 0.3V
VBST........................................................ VSW + 6V
VOVP – VSS....................................... –0.3V to +6V
VEN – VINGND .................................... –0.3V to +6V
VDIM – VINGND ................................... –0.3V to +6V
VINGND – VSS .................................... –0.3V to 40V
Continuous Power Dissipation (TA = +25°C) (2)
………………………………………………....2.3W
Junction Temperature ............................... 150C
Lead Temperature .................................... 260C
Storage Temperature ............... –65C to +150C
MSOP8E (Exposed Pad) ........ 55 ...... 12... C/W
θJA
θJC
Notes:
1) Exceeding these ratings may damage the device.
2) The maximum allowable power dissipation is a function of the
maximum junction temperature TJ (MAX), the junction-toambient thermal resistance θJA, and the ambient temperature
TA. The maximum allowable continuous power dissipation at
any ambient temperature is calculated by PD (MAX) = (TJ
(MAX)-TA)/θJA. Exceeding the maximum allowable power
dissipation will cause excessive die temperature, and the
regulator will go into thermal shutdown. Internal thermal
shutdown circuitry protects the device from permanent
damage.
3) The device is not guaranteed to function outside of its
operating conditions.
4) Measured on JESD51-7, 4-layer PCB.
Recommended Operating Conditions (3)
Supply Voltage VDD – VSS ................ 4.5V to 36V
Operating Junct. Temp (TJ) ..... –40C to +125C
MP2481 Rev. 1.5
8/24/2020
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2020 MPS. All Rights Reserved.
2
MP2481 –36V, 1.2A, 1.4MHz WHITE LED DRIVER
ELECTRICAL CHARACTERISTICS
VIN = 12V, TA = +25C, all voltages with respect to VSS, unless otherwise noted.
Parameters
Symbol Condition
Feedback Voltage
VFB
4.5V VIN 36V
Feedback Current
IFB
VFB = 0.2V
Switch-On Resistance (5)
RDS(ON)
Switch Leakage
VEN = 0V, VSW = 0V
Switch Current Limit (5)
Oscillator Frequency
fSW
VFB = 0.1V
Fold-back Frequency
VOVP < 0.4V
Maximum Duty Cycle
VFB = 0.1V
Minimum On-Time (5)
tON
Under Voltage Lockout Threshold Rising
Under
Voltage
Lockout
Threshold
Hysteresis
VEN = 2V
EN Input Current
VEN = 0V
EN OFF Threshold (w/Respect to INGND)
VEN Falling
EN ON Threshold (w/Respect to INGND)
VEN Rising
Supply Current (Quiescent)
IQ
VEN = 2V, VFB = 1V
Thermal Shutdown (5)
Open LED OV Threshold
VOVP, th
Open LED OV Hysteresis
VOVP, hys
Min
0.187
Typ
0.203
0.2
0.30
Max
0.219
10
1.0
3.1
2.0
1.4
120
89
100
3.4
1.8
3.7
Units
V
μA
Ω
μA
A
MHz
kHz
%
ns
V
480
mV
2.0
0.1
μA
0.4
0.6
150
1.23
0.1
0.7
1.1
V
V
mA
°C
V
V
Note:
5) Guaranteed by design.
MP2481 Rev. 1.5
8/24/2020
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2020 MPS. All Rights Reserved.
3
MP2481 –36V, 1.2A, 1.4MHz WHITE LED DRIVER
PIN FUNCTIONS
Pin #
Name
1
VDD
2
VSS
3
OVP
4
FB
5
EN/DIM
6
INGND
7
BST
8
SW
MP2481 Rev. 1.5
8/24/2020
Description
Supply Voltage. The MP2481 operates from a +4.5V to +36V unregulated input (with respect
to VSS). C1 is needed to prevent large voltage spikes from appearing at the input.
Power Return Pin. Connect to the lowest potential in the circuit, which is typically the anode
of the Schottky rectifier. This pin is the voltage reference for the regulated output voltage.
For this reason care must be taken in its layout. This node should be placed outside of the
D1 to C1 ground path to prevent switching current spikes from inducing voltage noise into
the part. The exposed pad is also connected to this pin.
Over Voltage Protection Pin. Use one external resistor voltage divider to program OVP
threshold. When the OVP pin voltage (with respect to VSS) is lower than 0.4V, the chip
frequency will be folded back. Program the OVP pin voltage from 0.4V to 1.23V for normal
operation. When the OVP pin voltage reaches the shutdown threshold 1.23V, the switch will
be turned off
LED Current Feedback Input. MP2481 regulates the voltage across the current sensing
resistor between FB and VSS. Connect the current sensing resistor from the bottom of the
LED strings to VSS. The FB pin is connected to the bottom of the LED strings. The
regulation voltage is 0.2V.
On/Off Control Input and Dimming Command Input. A voltage greater than 0.7V will turn on
the chip. When the EN/DIM pin voltage (with respect to INGND) rises from 0.7V to 1.4V, the
LED current will change from 0% to 100% of the maximum LED current. To use PWM
dimming, apply a 100Hz to 1kHz square wave signal with amplitude greater than 1.4V to this
pin.
Input Ground Reference. This pin is the reference for the EN/DIM signal.
Bootstrap. A capacitor is connected between SW and BST pins to form a floating supply
across the power switch driver. This capacitor is needed to drive the power switch’s gate
above the supply voltage.
Switch Output. SW is the source of the internal MOSFET switch. Connect to the power
inductor and cathode of the Schottky rectifier.
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2020 MPS. All Rights Reserved.
4
MP2481 –36V, 1.2A, 1.4MHz WHITE LED DRIVER
TYPICAL PERFORMANCE CHARACTERISTICS
VIN=12V, ILED=1A, one 5W WLED, Step-down application (refer to Figure 6), unless otherwise
noted.
Steady State Operation
Open Load Protection
PWM Dimming
fPWM=1kHz,DPWM=50%
VSW
10V/div.
VSW
10V/div.
VFB
200mV/div.
VOUT
VOUT
2V/div.
VPWM
5V/div.
VSW
10V/div.
AC Coupled
200mV/div.
VOUT
2V/div.
ILED
500mA/div.
IINDUCTOR
500mA/div.
ILED
1A/div.
400ns/div
4
2
Efficiency vs.
Input Voltage
Short Circuit Protection
Short LED+ to INGND
100
1.0
90
LED CURRENT (A)
EFFICIENCY (%)
IINDUCTOR
500mA/div.
85
80
75
1 WLED,500mA 1 WLED,1A
70
65
60
0.8
0.6
0.4
0.2
0
0
4
1.2
2 WLEDs in series,500mA
3 WLEDs in series,500mA
95
VSW
10V/div.
LED Current vs.
Analog Dimming Voltage
10
20
30
INPUT VOLTAGE (V)
40
0.4
0.6 0.8 1.0 1.2 1.4 1.6 1.8
ANALOG DIMMING VOLTAGE (V)
LED Current vs.
PWM Dimming Duty
fPWM=1kHz
1.2
LED CURRENT (A)
1.0
0.8
0.6
0.4
0.2
0
0
0.2
0.4
0.6
0.8
1.0
PWM Dimming Duty
MP2481 Rev. 1.5
8/24/2020
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2020 MPS. All Rights Reserved.
5
MP2481 –36V, 1.2A, 1.4MHz WHITE LED DRIVER
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
VIN=12V, ILED=180mA, 3 WLEDs in series, 9 strings, Step-up/down application (refer to Figure 7),
unless otherwise noted.
Steady State Operation
Open Load Protection
PWM Dimming
fPWM=1kHz,DPWM=50%
VSW
20V/div.
VSW
10V/div.
VSW
20V/div.
VPWM
5V/div.
VSS
VSS
5V/div.
AC Coupled
200mV/div.
VSS
2V/div.
ILED
200mA/div.
ILED
200mA/div.
IINDUCTOR
500mA/div.
400ns/div
4
2
LED Current vs.Analog
Dimming Voltage
Efficiency vs.
Input Voltage
Short Circuit Protection
Short LED+ to VSS
90
200
EFFICIENCY (%)
VSW
10V/div.
IINDUCTOR
500mA/div.
4 series,400mA
80
3 series,400mA
75
3 series,9 paralleded,180mA total
70
65
60
4
LED CURRENT (mA)
180
85
160
140
120
100
80
60
40
20
0
5
10
15
20
25
INPUT VOLTAGE (V)
30
0
0.4
0.6 0.8 1.0 1.2 1.4 1.6 1.8
ANALOG DIMMING VOLTAGE (V)
LED Current vs.
PWM Dimming Duty
fPWM=1kHz
200
LED CURRENT (mA)
180
160
140
120
100
80
60
40
20
0
0
0.2
0.4
0.6
0.8
1.0
PWM Dimming Duty
MP2481 Rev. 1.5
8/24/2020
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2020 MPS. All Rights Reserved.
6
MP2481 –36V, 1.2A, 1.4MHz WHITE LED DRIVER
FUNCTION BLOCK DIAGRAM
VDD
POR&
REGULATOR
EN/DIM
4.0V
x20
RAMP
GENERATOR
CURRENT SENSE
AMPLIFIER
-+
EN
ENABLE
D
REGULATOR
BST
OVP
DIMMING
CONTROL
INGND
OSCILLATOR
1.4MHz/120KHz
S
REFERENCE
1pF
(VEN-0.7)/3.5
27pF
SOFTSTART
FB
0.2V
+
+ EA
--
ERROR
AMPLIFIER
+
--
Q
M1
DRIVER
R
CURRENT
LIMIT
COMPARATOR
+
--
PWM
COMPARATOR
SW
R R
VDD
+
+
--
OVP
1.2V
VSS
Figure 1—Function Block Diagram
MP2481 Rev. 1.5
8/24/2020
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2020 MPS. All Rights Reserved.
7
MP2481 –36V, 1.2A, 1.4MHz WHITE LED DRIVER
OPERATION
The MP2481 is a current mode regulator. The EA
output voltage is proportional to the peak inductor
current.
At the beginning of a cycle, M1 is off. The EA
output voltage is higher than the current sense
amplifier output, and the current comparator’s
output is low. The rising edge of the 1.4MHz CLK
signal sets the RS Flip-Flop. Its output turns on
M1 thus connecting the SW pin and inductor to
the input supply.
The increasing inductor current is sensed and
amplified by the Current Sense Amplifier. Ramp
compensation is summed to the Current Sense
Amplifier output and compared to the Error
Amplifier output by the PWM Comparator. When
the sum of the Current Sense Amplifier output
and the Slope Compensation signal exceeds the
EA output voltage, the RS Flip-Flop is reset and
M1 is turned off. The external Schottky rectifier
diode (D1) conducts the inductor current.
If the sum of the Current Sense Amplifier output
and the Slope Compensation signal does not
exceed the EA output for a whole cycle, then the
falling edge of the CLK resets the Flip-Flop.
The output of the Error Amplifier integrates the
voltage difference between the feedback and the
0.2V reference. The polarity is such that a FB pin
voltage lower than 0.2V increases the EA output
voltage. Since the EA output voltage is
proportional to the peak inductor current, an
increase in its voltage also increases current
delivered to the output.
Open Strings Protection
If LED strings are open, there is no voltage on
the FB pin. The duty cycle increases until V(VDD)
- V(VSS) reaches to 38V or V(OVP) - V(VSS)
reaches the shutdown threshold 1.23V. Then the
top switch is kept off. It will be switching again
when the voltage V(VDD) - V(VSS) and V(OVP) V(VSS) decreases sufficiently.
Spike Voltage Suppression and EMI
Improvement
The spike voltage of the VDD-to-SW should be
well limited to make sure it’s under the ABS of
VDD-to-SW. The high di/dt caused by MOS
on/off is the source of spike voltage, which
generates high spike voltage on the parasitic
MP2481 Rev. 1.5
8/24/2020
inductor and it’s also the source of the EMI.
Decrease the parasitic inductance is the most
effective method to improve the spike voltage
and EMI. As Figure 2 shows, the input capacitor
C2 together with the output capacitor C5 offers a
bypass paths for high di/dt, so these two
capacitor should be placed very close to the chip
with short, direct and wide traces.
If the spike voltage still cannot meet the request,
or EMI is not so good, a capacitor connected
between VDD and VSS can be used to further
shorten the high di/dt path. It should be placed as
close as possible to the chip too, and the traces
should be short and wide. But a schottky diode
D5 paralleled with C5 should be used to clamp
the voltage between VSS and INGND to make
sure it is under the ABS.
Q1
VDD
L
C2
D1
C1
VSS
Vout-
D2
C5
INGND
Vout+
Figure 2— spike voltage and EMI
improvement
Dimming Control
The MP2481 allows both DC and PWM dimming.
When V(EN/DIM) – V(INGND) is less than 0.4V,
the chip is turned off. For analog dimming, when
V(EN/DIM) – V(INGND) rises from 0.7V to 1.4V,
the LED current will change from 0% to 100% of
the maximum LED current. If V(EN/DIM) –
V(INGND) is higher than 1.4V, maximum LED
current is generated. If a PWM signal is used, its
amplitude V (EN/DIM) – V (INGND) must exceed
1.4V.
The MP2481 is designed with an internal EN
shut-down delay (see Figure 3). If EN is pulled
down, the FB reference drops to zero
immediately and the LED current decreases. But
the IC keeps internal logic on for about 2.5ms. In
this period, the IC may switch with very short
pulses in pulse-skipping mode, while the LED
current is zero since the FB reference is zero. It
has benefit that the IC will start up more quickly
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2020 MPS. All Rights Reserved.
8
MP2481 –36V, 1.2A, 1.4MHz WHITE LED DRIVER
without delay when next PWM duty comes. This
function offers the possibility to extend the PWM
dimming frequency and also the minimum PWM
on time for further dimming depth.
Figure 3— Internal EN Shut-down Delay Function Waveform Diagram
MP2481 Rev. 1.5
8/24/2020
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2020 MPS. All Rights Reserved.
9
MP2481 –36V, 1.2A, 1.4MHz WHITE LED DRIVER
APPLICATION INFORMATION
Setting the LED Current
The external resistor is used to set the
maximum LED current (see the schematic on
front page) through the use of the equation:
RSENSE =
0.200V
ILED
Setting the OVP point
To make sure the chip functions properly, the
Over Voltage Protection (OVP) resistor divider
must be set with proper value, the
recommended OVP point is about 1.3~1.5
times higher than the output voltage for normal
operation and over voltage protection.
Selecting the Inductor
(Step-Down Applications, see Figure 6)
A 3.3µH to 10µH inductor with a DC current
rating of at least 25% higher than the maximum
load current is recommended for most
applications. For highest efficiency, the
inductor’s DC resistance should be less than
200mΩ. Refer to Table 1 for suggested surface
mount inductors. For most designs, the required
inductance value can be derived from the
following equation.
L
VOUT ( VIN VOUT )
VIN IL f SW
Where VIN is the lowest input voltage, VOUT is
the output voltage, ∆IL is the inductor ripple
current.
Choose the inductor ripple current to be 30% of
the maximum load current. The maximum
inductor peak current is calculated from:
IL(MAX ) ILOAD
IL
2
If the calculation of above equations results in
an inductance greater than 10uH, a 10uH
inductor is still preferred.
Under light load conditions below 100mA, a
larger inductance is recommended for improved
efficiency.
Also note that the maximum recommended load
current is 1A if the duty cycle exceeds 35%.
(Step up/Down Applications, see Figure 7)
Operation at step-up/down mode, the
recommended inductance value can be derived
from the following equation:
L=
-VOUT VIN
(VIN - VOUT ) ∆IL fSW
When VIN is the lowest input voltage, VOUT is the
output voltage (negative), ∆IL is the inductor
ripple current.
For most step-up/down applications, a 3.3uH to
22uH with suitable DC current rating is
recommended. See Table 1 for suggested
inductors.
Selecting the Input Capacitor
The input capacitor reduces the surge current
drawn from the input supply and the switching
noise from the device. The input capacitor
impedance at the switching frequency should
be less than the input source impedance to
prevent high frequency switching current from
passing through the input. Ceramic capacitors
with X5R or X7R dielectrics are highly
recommended because of their low ESR and
small temperature coefficients. For most
applications, a 4.7µF capacitor is sufficient.
Table 1—Suggested Surface Mount Inductors
Manufacturer
Part Number
Inductance(µH)
Max DCR(Ω)
Toko
Sumida
Wurth Electronics
A921CY-4R7M
CDRH4D28C/LD
7440530047
4.7
4.7
4.7
0.027
0.036
0.038
MP2481 Rev. 1.5
8/24/2020
Current
Rating (A)
1.66
1.5
2.0
Dimensions
L x W x H (mm3)
6 x 6.3 x 3
5.1 x 5.1 x 3
5.8 x 5.8 x 2.8
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2020 MPS. All Rights Reserved.
10
MP2481 –36V, 1.2A, 1.4MHz WHITE LED DRIVER
Selecting the Output Capacitor
The output capacitor keeps the output voltage
ripple small and ensures feedback loop stability.
The output capacitor impedance should be low at
the switching frequency. Ceramic capacitors with
X5R or X7R dielectrics are recommended for
their low ESR characteristics. For most
applications, a 2.2µF ceramic capacitor will be
sufficient.
PCB Layout Considerations
Efficient PCB layout is critical for stable operation.
For best results, please refer to the guidelines
below:
Q1
VDD
L
C2
C1
D1
Make it
small
VSS
Vout-
D2
C5
INGND
Vout+
Figure 5— Buck-boost layout without VSS
capacitor
1. The high di/dt paths (VSS, VDD and SW)
should be placed very close to the device
with short, direct and wide traces.
2. The input capacitor needs to be as close
as possible to the VDD and VSS pins.
Q1
VDD
SW
L
C2
D1
C1
VSS
Make it
small
VoutC5
INGND
Vout+
Figure 4—Buck-boost layout without VSS
capacitor
3. The external feedback resistors should be
placed next to the FB pin.
4. Keep the switch node traces short and
away from the feedback network.
5. Add a capacitor between VSS and VDD
when the capacitor between VDD and
INGND cannot be placed as close to the
devise as possible. Make sure the
capacitor between VSS and VDD is very
close to the device and the traces are
short and wife.
MP2481 Rev. 1.5
8/24/2020
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2020 MPS. All Rights Reserved.
11
MP2481 –36V, 1.2A, 1.4MHz WHITE LED DRIVER
TYPICAL APPLICATION CIRCUITS
3
1
VIN
OVP
BST
VDD
7
C4
10nF
L1
4.7uH
LED+
SW 6
C2
4.7µ/50V
D1
C2
B140 2.2uF/25V
MP2481
R1
39kΩ
5 EN/DIM
EN/DIM
6 INGND
GND
VSS
FB
R2
10kΩ
4
LED-
R6
0.2Ω/1%
2
Figure 6—Step-Down White LED Driver Application
3
1
VIN
C1
1µ/50V
OVP
VDD
BST
7
C4
10nF
L1
4.7uH
LED+
SW 6
C2
4.7µ/50V
D1
C2
B140 2.2uF/25V
MP2481
EN/DIM
5 EN/DIM
GND
6 INGND
D2
B140
VSS
2
FB
4
R1
39kΩ
R2
10kΩ
LED-
R6
0.2Ω/1%
Figure 7—Step-up/down White LED Driver Application
MP2481 Rev. 1.5
8/24/2020
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2020 MPS. All Rights Reserved.
12
MP2481 –36V, 1.2A, 1.4MHz WHITE LED DRIVER
PACKAGE INFORMATION
MSOP8E W/ EXPOSED PAD
0.087(2.20)
0.099(2.50)
0.114(2.90)
0.122(3.10)
5
8
0.114(2.90)
0.122(3.10)
PIN 1 ID
(NOTE 5)
0.187(4.75)
0.199(5.05)
0.062(1.58)
0.074(1.88)
Exposed Pad
0.010(0.25)
0.014(0.35)
4
1
0.0256(0.65)BSC
BOTTOM VIEW
TOP VIEW
GAUGE PLANE
0.010(0.25)
0.030(0.75)
0.037(0.95)
0.043(1.10)MAX
SEATING PLANE
0.000(0.00)
0.006(0.15)
FRONT VIEW
0.016(0.40)
0.026(0.65)
0.004(0.10)
0.008(0.20)
NOTE:
0.181(4.60)
0.040(1.00)
0.016(0.40)
0 -6
o
SIDE VIEW
0.100(2.54)
0.075(1.90)
o
1) CONTROL DIMENSION IS IN INCHES. DIMENSION IN BRACKET IS
IN MILLIMETERS.
2) PACKAGE LENGTH DOES NOT INCLUDE MOLD FLASH,
PROTRUSION OR GATE BURR.
3) PACKAGE WIDTH DOES NOT INCLUDE INTERLEAD FLASH OR
PROTRUSION.
4) LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING)
SHALL BE 0.004" INCHES MAX.
5) PIN 1 IDENTIFICATION HAS HALF OR FULL CIRCLE OPTION.
6) DRAWING MEETS JEDEC MO-187, VARIATION AA-T.
7) DRAWING IS NOT TO SCALE.
0.0256(0.65)BSC
RECOMMENDED LAND PATTERN
MP2481 Rev. 1.5
8/24/2020
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2020 MPS. All Rights Reserved.
13
MP2481 –36V, 1.2A, 1.4MHz WHITE LED DRIVER
Revision History
Revision
#
1.5
Revision Date
08/24/2020
Description
Pages
Updated
1. Updated the typical application
Page 1
2. Updated the PCB layout consideration
page 11
3. Updated the typical application circuit
page 12
NOTICE: The information in this document is subject to change without notice. Please contact MPS for current specifications.
Users should warrant and guarantee that third party Intellectual Property rights are not infringed upon when integrating MPS
products into any application. MPS will not assume any legal responsibility for any said applications.
MP2481 Rev. 1.5
8/24/2020
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2020 MPS. All Rights Reserved.
14
工商网监
湘ICP备2023018690号
