MP2358DQ

TM MP2358 2A, 23V, 370KHz Step-Down Converter The Future of Analog IC Technology TM DESCRIPTION The MP2358 is a monolithic step-down switch mode converter with a built-in internal power MOSFET. It achieves 2A continuous output current over a wide input supply range with excellent load and line regulation. Current mode operation provides fast transient response and eases loop stabilization. Fault condition protection includes cycle-by-cycle current limiting and thermal shutdown. In shutdown mode the regulator draws 23µA of supply current. Programmable soft-start minimizes the inrush supply current and the output overshoot at initial startup. The MP2358 requires a minimum number of readily available standard external components. FEATURES • • • • • • • • • • • • 2A Output Current with QFN Package 0.18Ω Internal Power MOSFET Switch Stable with Low ESR Output Ceramic Capacitors 93% Efficiency 23µA Shutdown Mode Fixed 370KHz Frequency Thermal Shutdown Cycle-by-Cycle Over Current Protection Wide 4.75V to 23V Operating Input Range Output Adjustable from 0.92V to 16V Programmable Under Voltage Lockout Available in QFN10 (3mm x 3mm) and SO8 Packages Distributed Power Systems Battery Charger Pre-Regulator for Linear Regulators APPLICATIONS • • • EVALUATION BOARD REFERENCE Board Number EV2358DS-00A EV2358DQ-00A Dimensions 2.3” x 1.4” x 0.5” 2.0” x 1.3” x 0.4” “MPS” and “The Future of Analog IC Technology” are Trademarks of Monolithic Power Systems, Inc. TYPICAL APPLICATION INPUT 4.75V - 23V Efficiency vs Output Current C5 10nF 95 90 EFFICIENCY (%) OPEN = AUTOMATIC STARTUP IN EN BS SW 5.0V 3.3V 2.5V MP2358 SS GND FB COMP D1 B220A VOUT 3.3V/2A 85 80 75 70 65 60 0 0.5 1.0 1.5 C4 10nF C6 OPEN C3 3.9nF 2.0 2.5 MP2358_TAC_S01 OUTPUT CURRENT (A) MP2358_EC01 MP2358 Rev. 1.3 3/23/2006 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2006 MPS. All Rights Reserved. 1 TM MP2358 – 2A, 23V, 370KHz STEP-DOWN CONVERTER PACKAGE REFERENCE TOP VIEW TOP VIEW NC BS NC IN SW 1 2 3 4 5 10 9 8 7 6 SS EN COMP FB GND BS IN SW GND 1 2 3 4 8 7 6 5 SS EN COMP FB EXPOSED PAD ON BACKSIDE MP2358_PD02_SOIC8 MP2358_PD01-QFN10 Part Number* MP2358DQ * Package QFN10 (3mm x 3mm) Temperature –40°C to +85°C Part Number** MP2358DS Package SOIC8 Temperature –40°C to +85°C For Tape & Reel, add suffix –Z (eg. MP2358DQ–Z) For Lead Free, add suffix –LF (eg. MP2358DQ–LF–Z) ** For Tape & Reel, add suffix –Z (eg. MP2358DS–Z) For Lead Free, add suffix –LF (eg. MP2358DS–LF–Z) ABSOLUTE MAXIMUM RATINGS (1) Supply Voltage (VIN)..................................... 25V Switch Node Voltage (VSW) .......................... 26V Bootstrap Voltage (VBS) ....................... VSW + 6V Feedback Voltage (VFB) .................–0.3V to +6V Enable/UVLO Voltage (VEN)...........–0.3V to +6V Comp Voltage (VCOMP) ...................–0.3V to +6V SS Voltage (VSS) ............................–0.3V to +6V Junction Temperature ............................ +150°C Lead Temperature ................................. +260°C Storage Temperature.............. –65°C to +150°C Recommended Operating Conditions (2) Supply Voltage (VIN) ...................... 4.75V to 23V Operating Temperature.................–40°C to +85°C Thermal Resistance (3) QFN10 (3x3)........................... 50 ...... 12... °C/W SOIC8.................................... 105 ..... 50... °C/W Notes: 1) Exceeding these ratings may damage the device. 2) The device is not guaranteed to function outside of its operating conditions. 3) Measured on approximately 1” square of 1 oz copper. θJA θJC ELECTRICAL CHARACTERISTICS Parameter Feedback Voltage Upper Switch On Resistance Lower Switch On Resistance Upper Switch Leakage Current Limit (4) Current Sense Transconductance Output Current to Comp Pin Voltage Error Amplifier Voltage Gain Error Amplifier Transconductance Oscillator Frequency Short Circuit Frequency Soft-Start Pin Equivalent Output Resistance VIN = 12V, TA = +25°C, unless otherwise noted. Symbol Condition VFB 4.75V ≤ VIN ≤ 23V RDS(ON)1 RDS(ON)2 VEN = 0V, VSW = 0V GCS AVEA GEA fS ∆IC = ±10µA VFB = 0V 550 Min 0.892 Typ 0.920 0.18 10 0 3.4 1.95 400 830 370 240 9 1150 Max 0.948 Units V Ω Ω µA A A/V V/V µA/V KHz KHz kΩ 10 2.8 MP2358 Rev. 1.3 3/23/2006 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2006 MPS. All Rights Reserved. 2 TM MP2358 – 2A, 23V, 370KHz STEP-DOWN CONVERTER ELECTRICAL CHARACTERISTICS (continued) VIN = 12V, TA = +25°C, unless otherwise noted. Parameter Maximum Duty Cycle Minimum On Time EN Shutdown Threshold Enable Pull Up Current EN UVLO Threshold Rising EN UVLO Threshold Hysteresis Supply Current (Shutdown) Supply Current (Quiescent) Thermal Shutdown Note: 4) Slope compensation changes current limit above 40% duty cycle. Symbol Condition DMAX VFB = 0.8V tON ICC > 100µA VEN = 0V VEN Rising VEN ≤ 0.4V VEN ≥ 3V Min 0.7 2.37 Typ 90 100 1.0 1.0 2.50 210 23 1.1 160 Max 1.3 2.62 36 1.3 Units % ns V µA V mV µA mA °C PIN FUNCTIONS QFN10 SOIC8 Pin # Pin # 1 2 1 Name Description No Connect. Bootstrap. This capacitor (C5) is needed to drive the power switch’s gate above the supply voltage. It is connected between the SW and BS pins to form a floating supply across the power switch driver. The voltage across C5 is about 5V and is supplied by the internal +5V supply when the SW pin voltage is low. NC No Connect. IN Supply Voltage. The MP2358 operates from a +4.75V to +23V unregulated input. C1 is needed to prevent large voltage spikes from appearing at the input. SW Switch. This connects the inductor to either IN through M1 or to GND through M2. GND Ground. This pin is the voltage reference for the regulated output voltage. For this reason care must be taken in its layout. This node should be placed outside of the D1 to C1 ground path to prevent switching current spikes from inducing voltage noise into the part. FB Feedback. An external resistor divider from the output to GND, tapped to the FB pin, sets the output voltage. To prevent current limit runaway during a short circuit fault condition the frequency foldback comparator lowers the oscillator frequency when the FB voltage is below 400mV. COMP Compensation. This node is the output of the transconductance error amplifier and the input to the current comparator. Frequency compensation is done at this node by connecting a series R-C to ground. See the compensation section for exact details. EN Enable/UVLO. A voltage greater than 2.62V enables operation. Leave EN unconnected if unused. An Under Voltage Lockout (UVLO) function can be implemented by the addition of a resistor divider from VIN to GND. For complete low current shutdown the EN pin voltage needs to be less than 700mV. SS Soft-Start. Connect SS to an external capacitor to program the soft-start. If unused, leave it open. NC BS 3 4 5 6 2 3 4 7 5 8 6 9 7 10 8 MP2358 Rev. 1.3 3/23/2006 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2006 MPS. All Rights Reserved. 3 TM MP2358 – 2A, 23V, 370KHz STEP-DOWN CONVERTER TYPICAL PERFORMANCE CHARACTERISTICS VIN = 12V, VOUT = 3.3V, TA = +25°C, unless otherwise noted. Steady State IOUT = 2A VIN AC 500mV/div. VOUT AC 50mV/div. VSW 10V/div. IL 2A/div. VEN 10V/div. VOUT 2V/div. VSW 10V/div. IL 1A/div. Startup No Load 4ms/div. MP2358-TPC01 MP2358-TPC02 Startup 1A Load VEN 10V/div. VOUT 2V/div. VSW 10V/div. IL 1A/div. VEN 10V/div. VOUT 2V/div. VSW 10V/div. IL 1A/div. Startup 2A Load 4ms/div. MP2358-TPC03 4ms/div. MP2358-TPC04 VOUT AC 500mV/div. IL 1A/div. IOUT 1A/div. MP2358-TPC05 MP2358 Rev. 1.3 3/23/2006 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2006 MPS. All Rights Reserved. 4 TM MP2358 – 2A, 23V, 370KHz STEP-DOWN CONVERTER OPERATION The MP2358 is a current mode regulator. That is, the COMP pin voltage is proportional to the peak inductor current. At the beginning of a cycle: the upper transistor M1 is off; the lower transistor M2 is on (see Figure 1); the COMP pin voltage is higher than the current sense amplifier output; and the current comparator’s output is low. The rising edge of the 370KHz CLK signal sets the RS Flip-Flop. Its output turns off M2 and turns on M1 thus connecting the SW pin and inductor to the input supply. The increasing inductor current is sensed and amplified by the Current Sense Amplifier. Ramp compensation is summed to Current Sense Amplifier output and compared to the Error Amplifier output by the Current Comparator. When the Current Sense Amplifier plus Slope Compensation signal exceeds the COMP pin voltage, the RS Flip-Flop is reset and the MP2358 reverts to its initial M1 off, M2 on state. If the Current Sense Amplifier plus Slope Compensation signal does not exceed the COMP voltage, then the falling edge of the CLK resets the Flip-Flop. The output of the Error Amplifier integrates the voltage difference between the feedback and the 0.92V bandgap reference. The polarity is such that a FB pin voltage lower than 0.92V increases the COMP pin voltage. Since the COMP pin voltage is proportional to the peak inductor current an increase in its voltage increases current delivered to the output. The lower 10Ω switch ensures that the bootstrap capacitor voltage is charged during light load conditions. External Schottky Diode D1 carries the inductor current when M1 is off. IN INTERNAL REGULATORS OSCILLATOR 240KHz/ 370KHz + SLOPE COMP CLK CURRENT SENSE AMPLIFIER + -BS + S R 1.0V EN -2.50V/ 2.29V -SHUTDOWN COMPARATOR LOCKOUT COMPARATOR -Q Q SW 5V CURRENT COMPARATOR + + -- 1.8V GND FREQUENCY FOLDBACK COMPARATOR -- 0.4V 0.92V FB SS + ERROR AMPLIFIER COMP MP2358_BD01 Figure 1—Functional Block Diagram MP2358 Rev. 1.3 3/23/2006 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2006 MPS. All Rights Reserved. 5 TM MP2358 – 2A, 23V, 370KHz STEP-DOWN CONVERTER APPLICATION INFORMATION COMPONENT SELECTION Setting the Output Voltage The output voltage is set using a resistive voltage divider from the output voltage to FB pin. The voltage divider divides the output voltage down to the feedback voltage by the ratio: VFB = VOUT R2 R1 + R2 Choose an inductor that will not saturate under the maximum inductor peak current. The peak inductor current can be calculated by: ILP = ILOAD + ⎛ VOUT V × ⎜1 − OUT ⎜ 2 × fS × L ⎝ VIN ⎞ ⎟ ⎟ ⎠ Where ILOAD is the load current. Output Rectifier Diode The output rectifier diode supplies the current to the inductor when the high-side switch is off. To reduce losses due to the diode forward voltage and recovery times, use a Schottky diode. Choose a diode whose maximum reverse voltage rating is greater than the maximum input voltage, and whose current rating is greater than the maximum load current. Input Capacitor The input current to the step-down converter is discontinuous, therefore a capacitor is required to supply the AC current to the step-down converter while maintaining the DC input voltage. Use low ESR capacitors for the best performance. Ceramic capacitors are preferred, but tantalum or low-ESR electrolytic capacitors may also suffice. Since the input capacitor absorbs the input switching current it requires an adequate ripple current rating. The RMS current in the input capacitor can be estimated by: I C 2 = ILOAD × VOUT ⎛ VOUT ×⎜1− VIN ⎜ VIN ⎝ ⎞ ⎟ ⎟ ⎠ Where VFB is the feedback voltage and VOUT is the output voltage. Thus the output voltage is: VOUT = 0.92 × R1 + R2 R2 A typical value for R2 can be as high as 100kΩ, but a typical value is 10kΩ. Using that value, R1 is determined by: R1 = 10.87 × ( VOUT − 0.92) For example, for a 3.3V output voltage, R2 is 10kΩ, and R1 is 25.8kΩ. Inductor The inductor is required to supply constant current to the output load while being driven by the switched input voltage. A larger value inductor will result in less ripple current that will result in lower output ripple voltage. However, the larger value inductor will have a larger physical size, higher series resistance, and/or lower saturation current. A good rule for determining the inductance to use is to allow the peak-to-peak ripple current in the inductor to be approximately 30% of the maximum switch current limit. Also, make sure that the peak inductor current is below the maximum switch current limit. The inductance value can be calculated by: L= ⎛ ⎞ VOUT V × ⎜1 − OUT ⎟ ⎜ fS × ∆IL ⎝ VIN ⎟ ⎠ The worst-case condition occurs at VIN = 2VOUT, where: I C2 = ILOAD 2 Where fS is the switching frequency, ∆IL is the peak-to-peak inductor ripple current and VIN is the input voltage. For simplification, choose the input capacitor whose RMS current rating greater than half of the maximum load current. MP2358 Rev. 1.3 3/23/2006 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2006 MPS. All Rights Reserved. 6 TM MP2358 – 2A, 23V, 370KHz STEP-DOWN CONVERTER The input capacitor can be electrolytic, tantalum or ceramic. When using electrolytic or tantalum capacitors, a small, high quality ceramic capacitor, i.e. 0.1µF, should be placed as close to the IC as possible. When using ceramic capacitors, make sure that they have enough capacitance to provide sufficient charge to prevent excessive voltage ripple at input. The input voltage ripple caused by capacitance can be estimated by: ∆VIN = ⎛ ILOAD V V × OUT × ⎜1 − OUT fS × C1 VIN ⎜ VIN ⎝ ⎞ ⎟ ⎟ ⎠ Compensation Components The MP2358 employs current mode control for easy compensation and fast transient response. The system stability and transient response are controlled through the COMP pin. COMP pin is the output of the internal transconductance error amplifier. A series capacitor-resistor combination sets a pole-zero combination to control the characteristics of the control system. The DC gain of the voltage feedback loop is given by: A VDC = R LOAD × G CS × A VEA × VFB VOUT Where C1 is the input capacitance value. Output Capacitor The output capacitor is required to maintain the DC output voltage. Ceramic, tantalum, or low ESR electrolytic capacitors are recommended. Low ESR capacitors are preferred to keep the output voltage ripple low. The output voltage ripple can be estimated by: ∆VOUT = VOUT ⎛ V × ⎜1 − OUT fS × L ⎜ VIN ⎝ ⎞ ⎞⎛ 1 ⎟ ⎟ × ⎜ R ESR + ⎟⎜ 8 × f S × C2 ⎟ ⎠⎝ ⎠ Where RLOAD is the load resistor value, GCS is the current sense transconductance and AVEA is the error amplifier voltage gain. The system has two poles of importance. One is due to the compensation capacitor (C3) and the output resistor of error amplifier, and the other is due to the output capacitor and the load resistor. These poles are located at: fP1 = fP2 = GEA 2π × C3 × A VEA 1 2π × C2 × R LOAD Where L is the inductor value, RESR is the equivalent series resistance (ESR) value of the output capacitor and C2 is the output capacitance value. In the case of ceramic capacitors, the impedance at the switching frequency is dominated by the capacitance. The output voltage ripple is mainly caused by the capacitance. For simplification, the output voltage ripple can be estimated by: ∆VOUT = VOUT 8 × fS 2 Where GEA is transconductance. the error amplifier The system has one zero of importance, due to the compensation capacitor (C3) and the compensation resistor (R3). This zero is located at: f Z1 = 1 2π × C3 × R3 ⎛ V × ⎜1 − OUT ⎜ VIN × L × C2 ⎝ ⎞ ⎟ ⎟ ⎠ In the case of tantalum or electrolytic capacitors, the ESR dominates the impedance at the switching frequency. For simplification, the output ripple can be approximated to: ∆VOUT = VOUT ⎛ V ⎞ × ⎜1 − OUT ⎟ × RESR fS × L ⎝ VIN ⎠ The system may have another zero of importance, if the output capacitor has a large capacitance and/or a high ESR value. The zero, due to the ESR and capacitance of the output capacitor, is located at: fESR = 1 2π × C2 × R ESR The characteristics of the output capacitor also affect the stability of the regulation system. The MP2358 can be optimized for a wide range of capacitance and ESR values. MP2358 Rev. 1.3 3/23/2006 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2006 MPS. All Rights Reserved. 7 TM MP2358 – 2A, 23V, 370KHz STEP-DOWN CONVERTER In this case, a third pole set by compensation capacitor (C6) and compensation resistor (R3) is used compensate the effect of the ESR zero on loop gain. This pole is located at: f P3 = 1 2π × C6 × R3 the the to the 3. Determine if the second compensation capacitor (C6) is required. It is required if the ESR zero of the output capacitor is located at less than half of the switching frequency, or the following relationship is valid: f 1 2 π × R3 × f C MP2358_F02 Figure 2—External Bootstrap Diode This diode is also recommended for high duty cycle operation (when VOUT >65%) and high VIN output voltage (VOUT>12V) applications. Where R3 is the compensation resistor value. MP2358 Rev. 1.3 3/23/2006 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2006 MPS. All Rights Reserved. 8 TM MP2358 – 2A, 23V, 370KHz STEP-DOWN CONVERTER PACKAGE INFORMATION QFN10 (3mm x 3mm) Pin 1 Identif ication 2.95 3.05 0.20 0.30 10 0.35 0.45 Pin 1 Identif ication R0.200TY P 1 2.95 3.05 QFN10L (3 x 3mm) 0.500 Bsc 6 5 2.35 2.000 2.45 Ref Exp. DAP Top View 1.65 1.75 Exp. DAP BottomView 0.85 0.95 0.0000.050 0.178 0.228 Side View Note: 1) Dimensions arein millimeters. SOIC8 PIN 1 IDENT. 0.229(5.820) 0.244(6.200) 0.150(3.810) 0.157(4.000) 0.0075(0.191) 0.0098(0.249) SEE DETAIL "A" 0.013(0.330) 0.020(0.508) 0.050(1.270)BSC 0.011(0.280) x 45o 0.020(0.508) 0.189(4.800) 0.197(5.004) 0.053(1.350) 0.068(1.730) 0.049(1.250) 0.060(1.524) 0o-8o 0.016(0.410) 0.050(1.270) DETAIL "A" SEATING PLANE 0.001(0.030) 0.004(0.101) NOTE: 1) Control dimension is in inches. Dimension in bracket is millimeters. NOTICE: The information in this document is subject to change without notice. Please contact MPS for current specifications. Users should warrant and guarantee that third party Intellectual Property rights are not infringed upon when integrating MPS products into any application. MPS will not assume any legal responsibility for any said applications. MP2358 Rev. 1.3 3/23/2006 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2006 MPS. All Rights Reserved. 9