MP2410A
24V, 2A, 1MHz, Synchronous,
Step-Down, LED Driver
The Future of Analog IC Technology
DESCRIPTION
FEATURES
The MP2410A is a 24V, monolithic, synchronous,
step-down, white LED driver with a built-in power
MOSFET and rectifier. It achieves up to 2A of
continuous output current with excellent load and
line regulation. Peak current mode operation
provides fast transient response and eases loop
stabilization.
The MP2410A incorporates both analog and
PWM dimming onto a single control pin. The
MP2410A implements deep analog dimming and
PWM dimming.
Full protection features include cycle-by-cycle
peak-current
limiting,
output
short-circuit
protection (SCP), open LED protection, NTC
thermal protection, and thermal shutdown.
The MP2410A requires a minimum number of
readily available, standard, external components
and is available in TSOT23-6 and TSOT23-8
packages.
4.2V to 24V Wide Input Range
Synchronous Step-Down Converter
100mΩ Internal High-Side Power MOSFET
80mΩ Internal Low-Side Synchronous
Rectifier
Peak Current Mode Control
Up to 2A Continuous Output Current
100mV Feedback Voltage
Up to 97% Efficiency
Fixed 1MHz Switching Frequency
Analog and PWM Dimming
Cycle-by-Cycle Current Limit
Inherent LED Open Protection
Output Short-Circuit Protection (SCP)
NTC Thermal Protection
Thermal Shutdown
Auto-Restart Function
Available in TSOT23-6 and TSOT23-8
Packages
APPLICATIONS
Infrared LED Driver
General LED Driver
Flashlight
Handheld Computers Backlight
All MPS parts are lead-free, halogen-free, and adhere to the RoHS directive.
For MPS green status, please visit the MPS website under Quality
Assurance. “MPS” and “The Future of Analog IC Technology” are registered
trademarks of Monolithic Power Systems, Inc.
TYPICAL APPLICATION
100
98
96
94
92
90
88
86
84
6 8 10 12 14 16 18 20 22 24 26
VIN (V)
MP2410A Rev. 1.01
www.MonolithicPower.com
6/19/2019
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2019 MPS. All Rights Reserved.
1
MP2410A – 24V, 2A, 1MHZ, SYNCHRONOUS, STEP-DOWN, LED DRIVER
ORDERING INFORMATION
Part Number
MP2410AGJ*
MP2410AGJE**
Package
TSOT23-6
TSOT23-8
Top Marking
See Below
* For Tape & Reel, add suffix –Z (e.g. MP2410AGJ–Z)
** For Tape & Reel, add suffix –Z (e.g. MP2410AGJE–Z)
TOP MARKING (TSOT23-6)
ARX: Product code of MP2410AGJ
Y: Year code
TOP MARKING (TSOT23-8)
ARV: Product code of MP2410AGJE
Y: Year code
PACKAGE REFERENCE
TOP VIEW
TSOT23-6
TOP VIEW
NTC
1
8
NC
FB
2
7
VIN
EN/DIM
3
6
SW
BST
4
5
GND
TSOT23-8
MP2410A Rev. 1.01
www.MonolithicPower.com
6/19/2019
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2019 MPS. All Rights Reserved.
2
MP2410A – 24V, 2A, 1MHZ, SYNCHRONOUS, STEP-DOWN, LED DRIVER
ABSOLUTE MAXIMUM
RATINGS (1)
Supply voltage (VIN) ...................................... 26V
VSW ........................................ -0.3V to VIN + 0.3V
VBST........................................................ VSW + 6V
All other pins ................................... -0.3V to +6V
Continuous power dissipation (TA = 25°C) (2)
TSOT23-6 ................................................. 1.25W
TSOT23-8 ................................................. 1.25W
Junction temperature ................................ 150°C
Lead temperature...................................... 260°C
Storage temperature .................-65°C to +150°C
ESD capability human body mode ............ 2.0kV
Recommended Operating Conditions (3)
Thermal Resistance (4)
θJA
θJC
TSOT23-6 ............................... 100 ..... 55... °C/W
TSOT23-8 ............................... 100 ..... 55... °C/W
NOTES:
1) Exceeding these ratings may damage the device.
2) The maximum allowable power dissipation is a function of the
maximum junction temperature TJ (MAX), the junction-toambient thermal resistance θJA, and the ambient temperature
TA. The maximum allowable continuous power dissipation at
any ambient temperature is calculated by PD (MAX) = (TJ
(MAX)-TA)/θJA. Exceeding the maximum allowable power
dissipation produces an excessive die temperature, causing
the regulator to go into thermal shutdown. Internal thermal
shutdown circuitry protects the device from permanent
damage.
3) The device is not guaranteed to function outside of its
operating conditions.
4) Measured on JESD51-7, 4-layer PCB.
Supply voltage (VIN) ......................... 4.2V to 24V
Operating junction temp. (TJ)… .. -40°C to 125°C
MP2410A Rev. 1.01
www.MonolithicPower.com
6/19/2019
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2019 MPS. All Rights Reserved.
3
MP2410A – 24V, 2A, 1MHZ, SYNCHRONOUS, STEP-DOWN, LED DRIVER
ELECTRICAL CHARACTERISTICS
Typical values are VIN = 12V, TJ = 25°C, unless otherwise noted. Minimum and maximum values
are at VIN = 12V, TJ = -40°C to +125°C, unless otherwise noted, guaranteed by characterization.
Parameters
Supply Voltage
Operating range
Turn on threshold
Hysteretic voltage
Supply Current
Shutdown current
Quiescent current
Enable and Dimming (EN/DIM)
EN/DIM off threshold
EN/DIM on threshold
Turn off delay time
EN/DIM pull-up current
Max analog dimming threshold
Min analog dimming threshold
Feedback (FB)
Feedback voltage
Feedback current
Power Switch
High-side MOSFET on
resistance
Low-side synchronous rectifier
switch on resistance
Switch leakage
Symbol
Max
Units
24
4
V
V
V
10
0.9
50
1.1
μA
mA
0.27
0.545
16
2.8
1.31
0.63
0.31
0.59
22
3.8
1.44
0.7
0.35
0.635
28
5.3
1.57
0.78
V
V
ms
μA
V
V
93
100
30
107
75
mV
nA
100
110
80
90
170
180
140
150
1
mΩ
mΩ
mΩ
mΩ
μA
3.5
5
6.6
A
-890
-630
-330
mA
3.6
5.5
7
A
0.8
90
1.2
tON_MIN
1
94
70
MHz
%
ns
tSTART
2.4
VIN
VIN_ON
VIN_HYS
ISD
IQ
VEN_OFF
VEN_ON
tOFF_DELAY
IEN/DIM
VADIM_MAX
VADIM_MIN
VFB
IFB
RDS(ON)_H
RDS(ON)_L
ISW_LKG
High-side current limit
ILIMIT_H
Low-side current limit
ILIMIT_L
OCP current threshold
IOCP
Oscillator frequency
Maximum duty cycle
Minimum on time
Restart Timer
Hiccup timer at fault condition
Bootstrap
fSW
DMAX
Bias voltage for high-side driver
NTC
High-threshold voltage
Low-threshold voltage
Shutdown threshold
Shutdown voltage hysteresis
Pull-up current source
Leakage current
Thermal Shutdown
Thermal shutdown threshold (5)
Thermal shutdown hysteresis(5)
Condition
Min
After turn on
VIN rising edge
4.2
3.5
VEN = 0V
VEN = 2V, VFB = 200mV
VEN/DIM falling edge
VEN/DIM rising edge
VEN = 0V
Theoretically, VFB = 100mV
VFB = 5mV
4.2V VIN 24V
VFB = 150mV
VIN = 5.0V
VIN = 4.2V
VIN = 5.0V
VIN = 4.2V
VEN = 0V, VSW = 0V
When high-side switch
turns on
When low-side switch turns
on
Both for high side and low
side
VFB = 80mV
VFB = 80mV
Typ
3.7
0.12
ms
VBST-VSW
5.5V ≤ VIN ≤ 24V
VIN = 4.2V
4.8
3.6
5.1
5.5
V
V
VH_NTC
VL_NTC
VSD_NTC
VFB = 95mV
VFB = 5mV
VNTC falling edge
1.16
0.76
0.34
55
41
1.25
0.82
0.41
110
58
1.34
0.88
0.47
185
72
1
V
V
V
mV
μA
μA
VSD_NTC_HYS
IPULL_UP_NTC
INTC_LKG
TSD
THYS
150
60
°C
°C
NOTE:
5) Guaranteed by characterization.
MP2410A Rev. 1.01
www.MonolithicPower.com
6/19/2019
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2019 MPS. All Rights Reserved.
4
MP2410A – 24V, 2A, 1MHZ, SYNCHRONOUS, STEP-DOWN, LED DRIVER
TYPICAL PERFORMANCE CHARACTERISTICS
103
102
180
160
160
140
140
120
120
100
100
80
80
60
101
100
99
98
97
96
95
-50 -25 0
25 50 75 100 125 150
60
-50 -25 0
25 50 75 100 125 150
40
-50 -25 0
25 50 75 100 125 150
MP2410A Rev. 1.01
www.MonolithicPower.com
6/19/2019
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2019 MPS. All Rights Reserved.
5
MP2410A – 24V, 2A, 1MHZ, SYNCHRONOUS, STEP-DOWN, LED DRIVER
TYPICAL PERFORMACE CHARACTERISTICS (continued)
Performance waveforms are tested on the evaluation board.
VIN = 12V, 2 WLEDs in series, VOUT = 5.9V, ILED = 1.5A, L = 4.7μH, TA = 25°C, unless otherwise
noted.
Efficiency vs. VIN
Line Regulation
2 WLEDs in series
2 WLEDs in series
1.6
100
100
98
97
96
94
0.8
94
91
0.4
92
88
1.2
VIN=5V
0.0
VIN=12V
90
85
88
82
-0.8
86
79
-1.2
84
76
6 8 10 12 14 16 18 20 22 24 26
VIN (V)
Load Regulation
1.4
1.2
ILED (A)
0.2
0.0
-0.2
VIN=12V
-0.4
VDIM Falling
1.0
0.8
0.6
0.4 VDIM Rising
0.2
-0.6
0 1 2 3 4 5 6 7 8 9 10 11
VOUT (V)
0.0
0.2 0.4 0.6 0.8 1 1.2 1.4 1.6
VDIM ANALOG LEVEL (V)
ILED (A)
VIN=5V
0.4
6
8 10 12 14 16 18 20 22 24 26
VIN (V)
PWM Dimming Curve
1.6
0.6
-0.8
-1.6
0 1 2 3 4 5 6 7 8 9 10 11
VOUT (V)
Analog Dimming Curve
1 to 7 IR LEDs in series,
ILED=500mA, L=22 H
0.8
-0.4
1.5
1.4
1.3
200Hz
1.2
1.1
1.0
0.9
0.8
1kHz
0.7
0.6
20kHz
0.5
0.4
0.3
0.2
0.1
0.0
0 10 20 30 40 50 60 70 80 90 100
NTC Curve
1.6
1.4
ILED (A)
1.2
1.0
0.8
0.6
0.4
0.2
0.0
0.3
0.5
0.7 0.9 1.1 1.3
VNTC LEVEL (V)
1.5
MP2410A Rev. 1.01
www.MonolithicPower.com
6/19/2019
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2019 MPS. All Rights Reserved.
6
MP2410A – 24V, 2A, 1MHZ, SYNCHRONOUS, STEP-DOWN, LED DRIVER
TYPICAL PERFORMACE CHARACTERISTICS (continued)
Performance waveforms are tested on the evaluation board.
VIN = 12V, 2 WLEDs in series, VOUT = 5.9V, ILED = 1.5A, L = 4.7μH, TA = 25°C, unless otherwise
noted.
Steady State
VIN Start-Up
VIN Shutdown
IL
500mA/div.
VIN
5V/div.
IL
500mA/div.
ILED
500mA/div.
IL
500mA/div.
VIN
2V/div.
VSW
5V/div.
VIN
5V/div.
ILED
500mA/div.
ILED
500mA/div.
VSW
10V/div.
VSW
10V/div.
EN Start-Up
EN Shutdown
Minimum Analog Dimming
VEN/DIM=0.6V
VEN
1V/div.
IL
500mA/div.
ILED
500mA/div.
IL
500mA/div.
ILED
500mA/div.
VEN
1V/div.
VSW
10V/div.
VSW
10V/div.
PWM Dimming
ILED
20mA/div.
VEN/DIM
200mV/div.
IL
500mA/div.
VSW
5V/div.
Short LED+ to LEDProtection
Open LED Protection
Fre=1KHz,VPWM=2V, Duty=50%
VOUT
2V/div.
VPWM
1V/div.
IL
200mA/div.
IL
500mA/div.
ILED
500mA/div.
VSW
10V/div.
IL
500mA/div.
VIN
2V/div.
VSW
5V/div.
VFB
50mV/div.
VSW
5V/div.
MP2410A Rev. 1.01
www.MonolithicPower.com
6/19/2019
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2019 MPS. All Rights Reserved.
7
MP2410A – 24V, 2A, 1MHZ, SYNCHRONOUS, STEP-DOWN, LED DRIVER
TYPICAL PERFORMACE CHARACTERISTICS (continued)
Performance waveforms are tested on the evaluation board.
VIN = 12V, 2 WLEDs in series, VOUT = 5.9V, ILED = 1.5A, L = 4.7μH, TA = 25°C, unless otherwise
noted.
Short LED+ to GND
Protection
IL
1A/div.
VSW
5V/div.
MP2410A Rev. 1.01
www.MonolithicPower.com
6/19/2019
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2019 MPS. All Rights Reserved.
8
MP2410A – 24V, 2A, 1MHZ, SYNCHRONOUS, STEP-DOWN, LED DRIVER
PIN FUNCTIONS
Pin #
TSOT23-6 TSOT23-8
Name
Description
Ground. GND is the voltage reference for the regulated output voltage.
Give careful consideration to GND during layout.
1
5
GND
2
6
SW
Switch output.
3
7
VIN
Supply voltage. The MP2410A operates on a 4.2V to 24V, unregulated
input. An input capacitor is needed to prevent large voltage spikes from
appearing at the input.
4
2
FB
Current sense feedback voltage. FB’s internal reference voltage is 0.1V.
5
3
EN/DIM
On/off control input and dimming command input. Leaving EN/DIM
floating or applying a voltage higher than 0.59V on EN/DIM turns on the
MP2410A. For analog dimming, when the EN/DIM voltage rises up from
0.7V to 1.44V, the output current changes from its min value to the fullscale LED current. For PWM dimming, apply a 100Hz to 2kHz PWM
signal with an amplitude higher than 1.5V to EN/DIM.
6
4
BST
Bootstrap. Connect a capacitor between SW and BST to form a floating
supply across the power switch driver. This capacitor is needed to drive
the power switch’s gate above the supply voltage.
-
1
NTC
LED temperature protection. Connect an NTC resistor from NTC to
GND to reduce the output current to protect the LED when the ambient
temperature rises up at high levels.
-
8
NC
No connection.
MP2410A Rev. 1.01
www.MonolithicPower.com
6/19/2019
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2019 MPS. All Rights Reserved.
9
MP2410A – 24V, 2A, 1MHZ, SYNCHRONOUS, STEP-DOWN, LED DRIVER
BLOCK DIAGRAM
Figure 1: Functional Block Diagram
MP2410A Rev. 1.01
www.MonolithicPower.com
6/19/2019
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2019 MPS. All Rights Reserved.
10
MP2410A – 24V, 2A, 1MHZ, SYNCHRONOUS, STEP-DOWN, LED DRIVER
OPERATION
The MP2410A is a high-frequency, synchronous,
rectified, step-down, switching mode LED driver
with a built-in, internal power MOSFET and
synchronous rectifier switch. The MP2410A
offers a very high-performance solution that
achieves up to 2A of continuous output LED
current with excellent load and line regulation
over a wide input supply range.
The MP2410A operates in a fixed 1MHz
frequency, and uses peak current control mode
to regulate the output current. A new switching
cycle is initiated by the internal clock at the
beginning of every switching cycle.
The integrated high-side power MOSFET is
turned on, and the inductor current rises linearly
to provide energy to the load. The high-side
power MOSFET remains on until its current
reaches the value of the COMP level, which is
the output of the internal error amplifier. The
output voltage of the error amplifier depends on
the difference of the output feedback and the
internal, high-precision reference.
The high-side power switch remains off until the
next clock cycle begins. After the high-side
switch turns off, the low-side sync switch turns on,
and the inductor current flows through the lowside switch. To prevent a shoot-through, a dead
time is implemented to prevent the high-side and
low-side FETs from turning on at the same time.
When the duty cycle of one switching period
reaches 94%, the current in the high-side power
MOSFET cannot reach the COMP-set current
value, and the high-side power MOSFET is
forced to turn off.
If both VIN and EN/DIM are higher than their
appropriate thresholds, the chip starts up. The
reference block starts first to generate stable
reference voltages and currents. The internal
regulator is then enabled. The regulator provides
a stable supply for the remaining circuitries.
Three events can shut down the chip: EN/DIM
low for longer than tOFF_DELAY, VIN drops below
UVLO, and thermal shutdown. In the shutdown
procedure, the signaling path is blocked first to
prevent any fault triggering. The COMP voltage
(VCOMP) and the internal supply rail are then
pulled down.
Error Amplifier (EA)
The internal, low, offset error amplifier compares
the FB voltage with the internal 100mV reference
and outputs a COMP voltage, which is inside of
the chip and is used to control the high-side
MOSFET peak current and regulate the output
current.
Internal Soft Start (SS)
A soft start (SS) is implemented to prevent the
converter output current from overshooting
during start-up. When the chip starts, the internal
circuitry generates a soft-start voltage that ramps
up from 0V. The soft-start period lasts until the
voltage on the soft-start capacitor exceeds the
0.1V reference voltage. At this point, the
reference voltage takes over.
Floating Driver and Bootstrap Charging
The high-side, floating, power MOSFET driver is
powered by an external bootstrap capacitor. The
bootstrap capacitor voltage is regulated internally.
During normal operation, a 5.1V bootstrap
voltage is maintained between BST and SW.
Under-Voltage Lockout (UVLO) and IC StartUp/Shutdown Procedure
Under-voltage lockout (UVLO) is implemented to
prevent the chip from operating at an insufficient
supply voltage. The MP2410A UVLO comparator
monitors the output voltage of the internal
regulator, which is supplied from VIN.
MP2410A Rev. 1.01
www.MonolithicPower.com
6/19/2019
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2019 MPS. All Rights Reserved.
11
MP2410A – 24V, 2A, 1MHZ, SYNCHRONOUS, STEP-DOWN, LED DRIVER
Enable and Dimming Control (EN/DIM)
EN/DIM is a control pin that turns the regulator
on and off and dims the output LED current.
Leave EN/DIM floating or drive it high to turn on
the MP2410A. After EN/DIM is pulled low for
tOFF_DELAY (22ms, typically), the MP2410A is
turned off. Figure 2 shows the control logic of
EN/DIM.
Figure 2: EN/DIM Time Sequence
Analog Dimming
Apply a DC signal on EN/DIM to dim the
MP2410A in analog dimming mode. When the
voltage on EN/DIM is lower than VADIM_MIN, the
LED current is regulated to the minimal scale.
When the voltage on EN/DIM is between
VADIM_MIN and VADIM_MAX, the LED current changes
from the minimal scale to the full scale of the
LED current. If the voltage on EN/DIM is higher
than VADIM_MAX, the maximum LED current is
regulated.
Figure 3 shows the analog dimming curve. Due
to the hysteretic of the EN/DIM on/off threshold,
the chip remains at the minimal LED current
longer at the VEN/DIM falling edge until VEN/DIM is
lower than VEN_OFF. The dimming curve is the
same in the linear dimming range.
PWM Dimming
Apply a PWM signal on EN/DIM to implement
PWM dimming mode. The dimming frequency is
recommended to be in the range of 100Hz to
2kHz to achieve good dimming linearity. The
digital signal’s amplitude must be higher than
1.5V.
Open LED
If the LED is open without a feedback signal, the
MP2410A works at the maximum duty cycle, and
the output voltage rises up close to the input
voltage. Every power component operates at a
safe state.
LED Short-Circuit Protection (SCP)
The MP2410A integrates LED short-circuit
protection (SCP) circuitry. There are several
features protecting the MP2410A from damage
when an LED short circuit occurs.
The MP2410A features a cycle-by-cycle current
limit to restrict the maximum current of the
inductor. A protection mechanism monitors the
FB level though an internal R-C filter. Once the
FB level rises up to reach VFB_BURST_AL, the chip
stops switching until the FB level drops to a lower
value, and the system works in burst mode.
In the worst-case scenario, the LED is shorted to
GND. If the cycle-by-cycle current-limit function
cannot clamp the current overshoot sufficiently,
then the current through both the high-side and
low-side FETs is also monitored by the overcurrent detector inside the chip. If this current is
higher than the short-circuit threshold (IOCP), the
MP2410A treats this as a short-circuit condition.
When an over-current condition or short-circuit
condition is detected, the MP2410A turns off both
the high-side and low-side MOSFETs for 2.4ms
and restarts. During this period, VCOMP is pulled
down to ground, so the restart from the fault
condition is also done with a soft start.
Figure 3: Analog Dimming Curve
MP2410A Rev. 1.01
www.MonolithicPower.com
6/19/2019
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2019 MPS. All Rights Reserved.
12
MP2410A – 24V, 2A, 1MHZ, SYNCHRONOUS, STEP-DOWN, LED DRIVER
Thermal Protection
NTC provides LED thermal protection. An NTC
resistor used to monitor the ambient temperature
can be connected to NTC directly. There is an
internal current source flowing out of NTC. The
corresponding voltage is generated on the
external NTC resistor and the LED current
changes (see Figure 4).
Thermal Shutdown
Thermal shutdown is implemented to prevent the
chip from operating at exceedingly high
temperatures. When the silicon die temperature
is higher than 150°C, OTP shuts down the entire
chip. When the temperature is below its lower
threshold (typically 90°C), the chip restarts.
ILED
Full Scale
Min Scale
0
VSD_NTC VL_NTC
VH_NTC
VNTC
Figure 4: NTC Curve
The NTC resistance value drops when the
ambient temperature rises up. If the NTC voltage
drops below VSD_NTC, the switching stops
completely, and the LED current drops to 0A, so
the LED lamp can be shut down by pulling NTC
down.
Additionally, to protect against any lethal thermal
damage, when the inner temperature exceeds
the OTP threshold, the MP2410A shuts down the
switching cycle with thermal shutdown until the
temperature drops to its lower threshold.
MP2410A Rev. 1.01
www.MonolithicPower.com
6/19/2019
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2019 MPS. All Rights Reserved.
13
MP2410A – 24V, 2A, 1MHZ, SYNCHRONOUS, STEP-DOWN, LED DRIVER
APPLICATION INFORMATION
Setting the LED Current
A current sense resistor is inserted between the
cathode of LED and GND. The current sense
resistor value can be calculated with Equation (1):
RS
0.1V
ILED
(1)
For a 2A LED current output, choose RS = 50mΩ.
Selecting the Inductor
An inductor less than 100µH with a nominal DC
current rating at least 25% higher than the
maximum load current is recommended for most
applications. For the highest efficiency, the
inductor’s DC resistance should be less than
100mΩ. For most designs, the required
inductance value can be derived from Equation
(2):
L
VOUT (VIN VOUT )
VIN IL fSW
(2)
Where ∆IL is the inductor ripple current.
Choose the inductor ripple current to be 30% of
the maximum load current. The maximum
inductor peak current can be calculated with
Equation (3):
IL(MAX) ILED
IL
2
(3)
Selecting the Input Capacitor
The input capacitor reduces the surge current
drawn from the input supply and the switching
noise from the device. The input capacitor
impedance at the switching frequency should be
less than the source impedance to prevent the
high-frequency switching current from passing
through the input. Ceramic capacitors with X5R
or X7R dielectrics are highly recommended
because of their low ESR and small temperature
coefficients. For most applications, a 10µF
capacitor is sufficient.
Selecting the Output Capacitor
The output capacitor keeps the output current
ripple small and ensures feedback loop stability.
The output capacitor impedance should be low at
the switching frequency. Ceramic capacitors with
X5R or X7R dielectrics are recommended for
their low ESR characteristics. For most
applications, a 10µF ceramic capacitor is
sufficient.
PCB Layout Guidelines
Efficient PCB layout is critical for stable operation.
For best results, refer to the guidelines below.
1. Place the high current paths (GND, VIN, and
SW) very close to the device with short, direct,
and wide traces.
2. Place the input capacitor as close to IN and
GND as possible.
3. Place the external feedback resistors next to
FB.
4. Keep the switch node traces short and away
from the feedback network.
For more information, please refer to the related
evaluation board datasheet.
MP2410A Rev. 1.01
www.MonolithicPower.com
6/19/2019
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2019 MPS. All Rights Reserved.
14
MP2410A – 24V, 2A, 1MHZ, SYNCHRONOUS, STEP-DOWN, LED DRIVER
TYPICAL APPLICATION CIRCUIT
Figure 5: Typical Buck Converter Application, VIN = 8V to 24V, VO = 5.9V, ILED = 1.5A
MP2410A Rev. 1.01
www.MonolithicPower.com
6/19/2019
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2019 MPS. All Rights Reserved.
15
MP2410A – 24V, 2A, 1MHZ, SYNCHRONOUS, STEP-DOWN, LED DRIVER
PACKAGE INFORMATION
TSOT23-6
MP2410A Rev. 1.01
www.MonolithicPower.com
6/19/2019
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2019 MPS. All Rights Reserved.
16
MP2410A – 24V, 2A, 1MHZ, SYNCHRONOUS, STEP-DOWN, LED DRIVER
PACKAGE INFORMATION (continued)
TSOT23-8
See note 7
EXAMPLE
TOP MARK
PIN 1 ID
IAAAA
RECOMMENDED LAND PATTERN
TOP VIEW
SEATING PLANE
SEE DETAIL'' A''
FRONT VIEW
SIDE VIEW
NOTE:
DETAIL ''A''
1) ALL DIMENSIONS ARE IN MILLIMETERS
.
2) PACKAGE LENGTH DOES NOT INCLUDE MOLD FLASH
,
PROTRUSION OR GATE BURR.
3) PACKAGE WIDTH DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION.
4) LEAD COPLANARITY(BOTTOM OF LEADS AFTER
FORMING) SHALL BE 0.10 MILLIMETERS MAX.
5) JEDEC REFERENCE IS MO-193, VARIATION BA.
6) DRAWING IS NOT TO SCALE.
7) PIN 1 IS LOWER LEFT PIN WHEN READING TOP MARK
FROM LEFT TO RIGHT, (SEE EXAMPLE TOP MARK)
NOTICE: The information in this document is subject to change without notice. Please contact MPS for current specifications.
Users should warrant and guarantee that third party Intellectual Property rights are not infringed upon when integrating MPS
products into any application. MPS will not assume any legal responsibility for any said applications.
MP2410A Rev. 1.01
www.MonolithicPower.com
6/19/2019
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2019 MPS. All Rights Reserved.
17
工商网监
湘ICP备2023018690号
