MP2492DQ-LF-P

厂商：
MPS(美国芯源)
封装：
VFDFN10
描述：
IC REG BUCK ADJUSTABLE 2A 10QFN

数据手册：

下载MP2492DQ-LF-P.pdf

立即购买

详情介绍
数据手册
价格&库存

MP2492DQ-LF-P 数据手册

MP2492 2A, 55V, 100kHz Step-Down Converter with Programmable Output Current Limit The Future of Analog IC Technology DESCRIPTION FEATURES The MP2492 is a monolithic step-down switch mode converter with a programmable output current limit. It achieves 2A continuous output current over a wide input supply range with excellent load and line regulation. The maximum output current can be programmed by sensing current through the inductor DC resistance (DCR) or an accurate sense resistor. MP2492 achieves low EMI signature with well controlled switching edges. Fault condition protection includes cycle-by-cycle current limiting, and thermal shutdown. The MP2492 requires a minimum number of readily available standard external components. The MP2492 is available in QFN10 (3mm x 3mm) and SOIC8E packages. • • • • • • • • • • • Wide 4.5V to 55V Operating Input Range Programmable up to 2A Output Current Output Adjustable from 0.8V to 15V Programmable Output Current Limit without power loss 0.25Ω Internal Power MOSFET Switch Stable with Low ESR Output Ceramic Capacitors Fixed 100kHz Frequency Low EMI signature Thermal Shutdown Cycle-by-Cycle Over Current Protection Available in QFN10 and SOIC8E Packages APPLICATIONS • • • USB Power Supplies Automotive Cigarette Lighter Adapters Power Supply for Linear Chargers “MPS” and “The Future of Analog IC Technology” are Registered Trademarks of Monolithic Power Systems, Inc. TYPICAL APPLICATION Efficiency 100 VIN =12V , VOUT =5V EFFICIENCY ( % ) 90 80 70 60 50 40 30 20 0.0 0.4 0.8 1.2 1.6 2.0 I OUT (A) MP2492 Rev. 1.0 12/20/2010 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2010 MPS. All Rights Reserved. 1 MP2492 – 2A, 55V, 100kHz WITH PROGRAMMABLE OUTPUT CURRENT LIMIT ORDERING INFORMATION Part Number Package Top Marking Free Air Temperature (TA) MP2492DN* SOIC8E MP2492DN –40°C to +85°C MP2492DQ** QFN10(3mmx3mm) 3Q –40°C to +85°C * For Tape & Reel, add suffix –Z (e.g. MP2492DN–Z). For RoHS compliant packaging, add suffix –LF (e.g. MP2492DN–LF–Z) ** For Tape & Reel, add suffix –Z (e.g. MP2492DQ–Z). For RoHS compliant packaging, add suffix –LF (e.g. MP2492DQ–LF–Z) PACKAGE REFERENCE VIN SW VIN SW GND BST GND BST FB ISP SS ISN EXPOSED PAD EN PGOOD FB ISP SS ISN ON BACKSIDE EXPOSED PAD CONNECT TO GND ON BACKSIDE CONNECT TO GND SOIC8E ABSOLUTE MAXIMUM RATINGS (1) Input Voltage VIN .......................................... 60V VSW ....................................... –0.3V to VIN + 0.3V VBST ................................................... VSW + 6.5V VISN, vISP ................................................ 0V to15V | VISN, - vISP | ........................................ 0 to 0.5V VEN, ....................................................... 0V to15V All Other Pins .............................. –0.3V to +6.5V (2) Continuous Power Dissipation (TA = +25°C) SOIC8E ...................................................... 2.5W QFN10 (3 x 3 mm) ..................................... 2.5W Junction Temperature ...............................150°C Lead Temperature ....................................260°C Storage Temperature .............. –50°C to +150°C MP2492 Rev. 1.0 12/20/2010 QFN10(3mmx3mm) Recommended Operating Conditions (3) Input Voltage VIN .............................. 4.5V to 55V Output Voltage VOUT (VIN>16.5V) ...... 0.8V to 15V Output Voltage VOUT (VIN65%) and high VIN output voltage (VOUT>12V) applications. MP2492 Rev. 1.0 12/20/2010 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2010 MPS. All Rights Reserved. 8 MP2492 – 2A, 55V, 100kHz WITH PROGRAMMABLE OUTPUT CURRENT LIMIT Output Current Sensing The output current can be sensed through the DC resistance (DCR) of the inductor, as shown in Figure 3a. For more accurate sensing, use a more accurate sense resistor. × b R b Ra R 2 T U IO = V mR 0C 0D 1 In Figure 3a, the output current limit is set as: + Where DCR is the DC resistance of the inductor winding. = 1R LC D S × b R × + a R C b R a R In Figure 3a, it is desirable to keep For more accurate sensing, use a more accurate sense resistor. T U IO = V E S m N E 0 S 0 1R In Figure 3b, the output current limit is set as: Figure 3—Current Sensing Methods MP2492 Rev. 1.0 12/20/2010 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2010 MPS. All Rights Reserved. 9 MP2492 – 2A, 55V, 100kHz WITH PROGRAMMABLE OUTPUT CURRENT LIMIT PACKAGE INFORMATION SOIC8E (EXPOSED PAD) 0.189(4.80) 0.197(5.00) 8 0.124(3.15) 0.136(3.45) 5 0.150(3.80) 0.157(4.00) PIN 1 ID 1 0.228(5.80) 0.244(6.20) 0.089(2.26) 0.101(2.56) 4 TOP VIEW BOTTOM VIEW SEE DETAIL "A" 0.013(0.33) 0.020(0.51) 0.051(1.30) 0.067(1.70) SEATING PLANE 0.000(0.00) 0.006(0.15) 0.0075(0.19) 0.0098(0.25) SIDE VIEW 0.050(1.27) BSC FRONT VIEW 0.010(0.25) x 45o 0.020(0.50) GAUGE PLANE 0.010(0.25) BSC 0.024(0.61) 0.050(1.27) 0o-8o 0.016(0.41) 0.050(1.27) 0.063(1.60) DETAIL "A" 0.103(2.62) 0.138(3.51) RECOMMENDED LAND PATTERN MP2492 Rev. 1.0 12/20/2010 0.213(5.40) NOTE: 1) CONTROL DIMENSION IS IN INCHES. DIMENSION IN BRACKET IS IN MILLIMETERS. 2) PACKAGE LENGTH DOES NOT INCLUDE MOLD FLASH , PROTRUSIONS OR GATE BURRS. 3) PACKAGE WIDTH DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. 4) LEAD COPLANARITY(BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.004" INCHES MAX. 5) DRAWING CONFORMS TO JEDEC MS-012, VARIATION BA. 6) DRAWING IS NOT TO SCALE. www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2010 MPS. All Rights Reserved. 10 MP2492 – 2A, 55V, 100kHz WITH PROGRAMMABLE OUTPUT CURRENT LIMIT QFN10 (3mm x 3mm) 2.90 3.10 0.30 0.50 PIN 1 ID MARKING 0.18 0.30 2.90 3.10 PIN 1 ID INDEX AREA 1.45 1.75 PIN 1 ID SEE DETAIL A 10 1 2.25 2.55 0.50 BSC 5 6 TOP VIEW BOTTOM VIEW PIN 1 ID OPTION A R0.20 TYP. PIN 1 ID OPTION B R0.20 TYP. 0.80 1.00 0.20 REF 0.00 0.05 SIDE VIEW DETAIL A NOTE: 2.90 0.70 1) ALL DIMENSIONS ARE IN MILLIMETERS. 2) EXPOSED PADDLE SIZE DOES NOT INCLUDE MOLD FLASH. 3) LEAD COPLANARITY SHALL BE 0.10 MILLIMETER MAX. 4) DRAWING CONFORMS TO JEDEC MO-229, VARIATION VEED-5. 5) DRAWING IS NOT TO SCALE. 1.70 0.25 2.50 0.50 RECOMMENDED LAND PATTERN NOTICE: The information in this document is subject to change without notice. Please contact MPS for current specifications. Users should warrant and guarantee that third party Intellectual Property rights are not infringed upon when integrating MPS products into any application. MPS will not assume any legal responsibility for any said applications. MP2492 Rev. 1.0 12/20/2010 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2010 MPS. All Rights Reserved. 11

下载 PDF

MP2492DQ-LF-P

物料型号：MP2492

器件简介： - MP2492是一款单片降压型开关稳压器，具有可编程输出电流限制功能。 - 它能够在宽输入电压范围内实现2A的连续输出电流，并具有出色的负载和线路调节性能。 - 最大输出电流可以通过感应电感器的直流电阻（DCR）或精确的感应电阻来编程设定。

引脚分配： - VIN：供电电压输入。 - GND：地。 - EN：开关控制输入。 - FB：反馈引脚，用于设定输出电压。 - SS：软启动和电流限制环补偿引脚。 - ISN/ISP：电流感应输入。 - PGOOD：电源良好信号输出。 - BST：自举引脚，用于驱动开关的门极电压。 - SW：开关输出。

参数特性： - 工作输入电压范围：4.5V至55V。 - 可编程输出电流高达2A。 - 输出电压可调节范围：0.8V至15V。 - 内部功率MOSFET开关导通电阻为0.25Ω。 - 固定100kHz的工作频率。 - 低EMI特性。 - 热关断保护和逐周期过电流保护。

功能详解： - MP2492采用电流模式控制，通过感应电感器电流来调节输出。 - 具有低EMI特性，通过控制开关边缘来减少电磁干扰。 - 保护功能包括逐周期电流限制和热关断。

应用信息： - 适用于汽车点烟器适配器、USB电源供应和线性充电器的电源供应。

封装信息： - 提供QFN10（3mm x 3mm）和SOIC8E两种封装形式。

MP2492DQ-LF-P 价格&库存

-> 查询更多价格&库存

很抱歉，暂时无法提供与“MP2492DQ-LF-P”相匹配的价格&库存，您可以联系我们找货

免费人工找货

搜索历史

MP2492DQ-LF-P

相关技术文章