MP4558DQ-LF-P

MPQ9361 Industrial Grade, High Performance Regulated Charge Pump The Future of Analog IC Technology DESCRIPTION FEATURES The MPQ9361 is a high performance, regulated charge pump converter. Its input voltage ranges from 2.8V to Vout. The output voltage is regulated to a fixed 5V. No external inductor is required for simplicity and compactness. Internal soft-start circuit effectively reduces the in-rush current both while start-up and mode change. • • • • • • • • • • • The MPQ9361 is available in a compact TSOT23-6 package Guaranteed Industrial Temp Range Limits Input Voltage Range: 2.8V to 5V Internal Soft-Start Output Maximum Current up to 110mA Fixed 5V Output Voltage with 30mV Ripple 2X Charge Pump Fixed 1.35MHz Switching Frequency Over Current Protection Short Circuit Protection In-rush Current limit TSOT23-6 package and Lead (pb)-Free APPLICATIONS • • • • • Cell phone, Smart phone, LED backlight PDA or hand Held Computer Camera Flash White LED LCD Display Supply TV-Remote Control “MPS” and “The Future of Analog IC Technology” are Registered Trademarks of Monolithic Power Systems, Inc. TYPICAL APPLICATION 5 IN OUT 1 MPQ9361 CP 3 EN MPQ9361 Rev. 0.91 5/21/2010 GND 2 6 CN 4 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2010 MPS. All Rights Reserved. 1 MPQ9361–HIGH PERFORMANCE REGULATED CHARGE PUMP ORDERING INFORMATION Part Number* Package Top Marking Free Air Temperature (TA) MPQ9361DJ TSOT23-6 U2 -40°C to +85°C * For Tape & Reel, add suffix –Z (e.g. MP MPQ9361DJ–Z); For RoHS compliant packaging, add suffix –LF (e.g. MPQ9361DJ–LF–Z) PACKAGE REFERENCE TOP VIEW OUT 1 6 CP GND 2 5 IN EN 3 4 CN ABSOLUTE MAXIMUM RATINGS (1) Thermal Resistance Supply Input Voltage....................-0.3V to +6.0V All Other Pins ...............................-0.3V to +6.0V Storage Temperature............... -65°C to +150°C Continuous Power Dissipation (TA = +25°C) (2) ........................................................... 0.64W Junction Temperature .............................+150°C Lead Temperature ..................................+260°C TSOT23-6.............................. 195 ..... 25... °C/W Recommended Operating Conditions (3) Supply Voltage VIN ..........................2.8V to 5.0V Output Voltage VOUT .................................... 5.0V Operating Junct. Temp (TJ)...... -40°C to +125°C MPQ9361 Rev. 0.91 5/21/2010 (4) θJA θJC Notes: 1) Exceeding these ratings may damage the device. 2) The maximum allowable power dissipation is a function of the maximum junction temperature TJ(MAX), the junction-toambient thermal resistance θJA, and the ambient temperature TA. The maximum allowable continuous power dissipation at any ambient temperature is calculated by PD(MAX)=(TJ(MAX)TA)/θJA. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. Internal thermal shutdown circuitry protects the device from permanent damage. 3) The device is not guaranteed to function outside of its operating conditions. 4) Measured on JESD51-7 4-layer board. www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2010 MPS. All Rights Reserved. 2 MPQ9361–HIGH PERFORMANCE REGULATED CHARGE PUMP ELECTRICAL CHARACTERISTICS VIN=3.7V, CIN=COUT=2.2uF, CP=0.22µF, TA=-40°C to +85°C. Typical values are at TA=25°C, unless otherwise noted. Parameter Input Supply Voltage Symbol Condition VIN Output Voltage VOUT Quiescent Current Maximum Output Current Over Current Protection Short Circuit Protection Output Ripple Shut Down Current Operation Frequency Enable Voltage, High Enable Voltage, Low Enable Pin Leakage MPQ9361 Rev. 0.91 5/21/2010 IQ IO IOCP ISHORT Min 2.8 Typ Max 5 4.8 5 5.2 4.6 5 2 5.2 4 350 500 TA =25°C 60 90 -40°C ≤ TA ≤ +85°C IOUT=60mA VIN=4.5V, VEN3.2V, IOUT3.2V VOUT=5V ISHDN FOSC VEN (HIGH) VEN (LOW) IEN VEN=5V 110 250 1.1 1 1.6 1.5 0.4 0.2 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2010 MPS. All Rights Reserved. Units V V mA mA mA mA mV µA MHz V 1 V µA 3 MPQ9361–HIGH PERFORMANCE REGULATED CHARGE PUMP PIN FUNCTIONS Pin # Name 1 OUT 2 GND 3 EN 4 5 6 CN IN CP MPQ9361 Rev. 0.91 5/21/2010 Description Output Voltage. Decoupled with a 2.2µF ceramic capacitor for a load current less than 60mA. For a load current greater than 60mA, use 10µF decoupling capacitor. Ground. Device Enable: A logic high input (VEN>1.5V) turns on the regulator. A logic low input (VEN>0.4V) Flying Capacitor Negative Terminal. Input. Flying Capacitor Positive Terminal. www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2010 MPS. All Rights Reserved. 4 MPQ9361–HIGH PERFORMANCE REGULATED CHARGE PUMP TYPICAL PERFORMANCE CHARACTERISTICS VIN=3.7V, VOUT=5V, C1=C2=2.2µF, C3=0.47µF. TA=25ºC, unless otherwise noted. Efficiency vs. Load Current Efficiency vs. Input Voltage Load regulation 90 82 IOUT=50mA 74 66 IOUT=20mA 58 5.0 IOUT=0mA IOUT=0mA 4.9 4.8 IOUT=60mA 4.7 IOUT=110mA 4.6 4.5 MPQ9361 Rev. 0.91 5/21/2010 0 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2010 MPS. All Rights Reserved. 5 MPQ9361–HIGH PERFORMANCE REGULATED CHARGE PUMP TYPICAL PERFORMANCE CHARACTERISTICS VIN=3.7V, VOUT=5V, C1=C2=2.2µF, C3=0.47µF. TA=25ºC, unless otherwise noted. (continued) Inrush Current Inrush Current Load PWM Dimming Operation VIN=2.8V, IOUT=64mA with resistor load VGN=VIN=3.6V, IOUT=64mA with resistor load VEN=VIN=2.8V, FPWM=100HZ VIN 2V/div VEN 2V/div VIN 2V/div VSW 2V/div VOUT 2V/div VOUT 5V/div VIN 2V/div VPWM 2V/div VOUT 2V/div IIN 0.2A/div IIN 0.5A/div IOUT 0.1A/div 10ms/div 2ms/div Load PWM Dimming Operation Normal Load Ripple Normal Load Ripple VEN=VIN=2.8V, FPWM=2KHZ VEN=VIN=2.8V, VOUT=5V, IOUT=60mA VIN=VEN=4V, IOUT=60mA VIN 2V/div VPWM 2V/div VOUT 2V/div IOUT 0.1A/div VIN 2V/div VOUT 50mV/div VOUT 50mV/div VIN 2V/div VCN 2V/div VCN 2V/div IOUT 50mA/div IOUT 50mA/div 400ns/div MPQ9361 Rev. 0.91 5/21/2010 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2010 MPS. All Rights Reserved. 400ns/div 6 MPQ9361–HIGH PERFORMANCE REGULATED CHARGE PUMP OPERATION C+ C- C+ VCC VOUT Switch Drivers C- Charge Pump OSC Mode Detection / Swtich Control Band-Gap VBG EN VSS 1.35Mhz OSC OSC Figure 1— Functional Block Diagram The MPQ9361 uses a switched capacitor charge pump to boost an input voltage to a regulated output voltage. Regulation is achieved by sensing the charge pump output voltage through an internal resistor divider network. A switched doubling circuit is enabled when the divided output drops below a preset trip point controlled by an internal comparator. The switching signal, which drives the charge pump, is created by an integrated oscillator within the control circuit block. The fixed charge pump switching frequency is approximately 1.35MHz. MPQ9361 Rev. 0.91 5/21/2010 The MPQ9361 has complete output short-circuit and thermal protection to safeguard the device under extreme operating conditions. An internal thermal protection circuit senses die temperature and will shut down the device if the internal junction temperature exceeds approximately 145°C. The charge pump will remain disabled until the fault condition is relieved. www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2010 MPS. All Rights Reserved. 7 MPQ9361–HIGH PERFORMANCE REGULATED CHARGE PUMP PACKAGE INFORMATION TSOT23-6 6 See Note 7 EXAMPLE TOP MARK PIN 1 0.95 BSC 0.60 TYP 2.80 3.00 4 AAAA 1 1.20 TYP 1.50 1.70 2 TY 2.60 3.00 3 TOP VIEW RECOMMENDED LAND PATTERN 0.84 0.90 1.00 MAX 0.0 0.2 SEATING PLANE 0.30 0.50 0.95 BSC 0.00 0.10 SEE DETAIL "A" FRONT VIEW SIDE VIEW NOTE: GAUGE PLANE 0.25 BSC 0.30 0.50 0o-8o DETAIL A 1) ALL DIMENSIONS ARE IN MILLIMETERS. 2) PACKAGE LENGTH DOES NOT INCLUDE MOLD FLASH PROTRUSION OR GATE BURR. 3) PACKAGE WIDTH DOES NOT INCLUDE INTERLEAD FL OR PROTRUSION. 4) LEAD COPLANARITY (BOTTOM OF LEADS AFTER FOR SHALL BE 0.10 MILLIMETERS MAX. 5) DRAWING CONFORMS TO JEDEC MO-193, VARIATION 6) DRAWING IS NOT TO SCALE. 7) PIN 1 IS LOWER LEFT PIN WHEN READING TOP MARK LEFT TO RIGHT, (SEE EXAMPLE TOP MARK) NOTICE: The information in this document is subject to change without notice. Users should warrant and guarantee that third party Intellectual Property rights are not infringed upon when integrating MPS products into any application. MPS will not assume any legal responsibility for any said applications. MPQ9361 Rev. 0.91 5/21/2010 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2010 MPS. All Rights Reserved. 8