MP5032GJ-P

MP5032 QC 3.0 Controller with Integrated Current-Limit Switch DESCRIPTION FEATURES The MP5032 integrates a USB current-limit switch and charging port identification circuit. The MP5032 achieves 3A of continuous output current over a wide input supply range.   The output of the USB switch is current-limit programmable. The MP5032 supports DCP schemes for battery charging specification (BC1.2), divider mode, 1.2V/1.2V mode, and quick charge specification (QC 3.0) without the need for external user interaction. The MP5032 compensation. provides linear line      drop   Full protection features include hiccup current limiting, input over-voltage protection (OVP), and thermal shutdown. Wide 3.6V to 14V Operating Input Voltage Range Supports QC 3.0 (3.6V - 12VOUT) and DCP Schemes for BC1.2, Divider Mode, and 1.2V/1.2V Mode Line Drop Compensation for 5V Output Fairly Constant Power Limit 32mΩ Low RDS(ON) Power MOSFET Input Discharge during High Voltage to Low Voltage Change Intelligent Input Over-Voltage Shutdown Protection Compatible with Buck and Boost Converters Available in a TSOT23-8 Package APPLICATIONS    The MP5032 requires a minimal number of readily available, standard, external components to complete the USB switch and charging mode auto-detection solution. The MP5032 is available in an 8-pin TSOT23 package. USB Power Supplies Automotive Cigarette Lighter Adapters Power Banks All MPS parts are lead-free, halogen-free, and adhere to the RoHS directive. For MPS green status, please visit MPS website under Quality Assurance. “MPS” and “The Future of Analog IC Technology” are registered trademarks of Monolithic Power Systems, Inc. TYPICAL APPLICATION OUT 3.6V-12V VIN 12V-36V C3 22μF BST IN MP2499M SW C5 0.1μF L1 15μH FB VCC AGND R4 33kΩ OUT IN C2 22μF R1 82.5kΩ EN/SYNC C4 0.1μF C1 66μF QC3.0 MP5032 DM ADJ R2 24.3kΩ DP ISENSE Type-A EN PGND R3 1.5kΩ ILIM GND Note: Set MP2499M original output to 3.5V by R1 and R2. MP5032 Rev r1.0 8/4/2017 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2017 MPS. All Rights Reserved. 1 MP5032 – QC 3.0 CONTROLLER WITH CURRENT-LIMIT SWITCH ORDERING INFORMATION Part Number* MP5032GJ Package TSOT23-8 Top Marking See Below * For Tape & Reel, add suffix –Z (e.g.MP5032GJ-Z) TOP MARKING AYB: Product code of MP5032GJ Y: Year code PACKAGE REFERENCE TOP VIEW EN DP OUT DM IN ILIM GND ADJ TSOT23-8 MP5032 Rev r1.0 8/4/2017 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2017 MPS. All Rights Reserved. 2 MP5032 – QC 3.0 CONTROLLER WITH CURRENT-LIMIT SWITCH θJA θJC ABSOLUTE MAXIMUM RATINGS (1) Thermal Resistance Supply voltage (VIN) ..................... -0.3V to +16V Output voltage (VOUT) ................... -0.3V to +16V All other pins .................................. -0.3V to +6V Junction temperature ............................... 150°C Lead temperature .................................... 260°C Continuous power dissipation (TA = +25°C) (2) (5) ................................................................ 1.89W TSOT23-8 EV5032-J-00A (5) .................. 66 ....... 23 ... °C/W JESD51-7 (6) ........................ 100 ...... 55 ... °C/W Recommended Operating Conditions (3) Supply voltage (VIN) .................... 3.6V to 14V (4) Output voltage (VOUT) .................. Follow with VIN Output current (IOUT)............................. Up to 3A Operating junction temp. (TJ). .. -40°C to +125°C MP5032 Rev 1.0 8/4/2017 NOTES: 1) Exceeding these ratings may damage the device. 2) The maximum allowable power dissipation is a function of the maximum junction temperature TJ (MAX), the junction-toambient thermal resistance θJA, and the ambient temperature TA. The maximum allowable continuous power dissipation at any ambient temperature is calculated by PD (MAX) = (TJ (MAX)-TA)/θJA. Exceeding the maximum allowable power dissipation produces an excessive die temperature, causing the regulator to go into thermal shutdown. Internal thermal shutdown circuitry protects the device from permanent damage. 3) The device is not guaranteed to function outside of its operating conditions. 4) For lower VIN applications, refer to the Operation section on page 12. 5) Measured on EV5032-J-00A, 2-layer PCB, 58mmx32mm, 2oz copper 6) Measured on JESD51-7, 4-layer PCB. www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2017 MPS. All Rights Reserved. 3 MP5032 – QC 3.0 CONTROLLER WITH CURRENT-LIMIT SWITCH ELECTRICAL CHARACTERISTICS VIN = 5V, RILIM = 1.5kΩ, TJ = -40°C to 125°C otherwise noted. Parameter VIN under-voltage lockout rising threshold UVLO hysteresis Second VIN under-voltage lockout rising threshold Second UVLO hysteresis EN rising threshold EN hysteresis EN auto pull-up current Shutdown current Supply current USB Power MOSFET (7) , typical value is tested at TJ = +25°C, unless Symbol Condition Min Typ Max Units VIN_UVLO1 ADJ starts to work 2.7 3.0 3.3 V VUVLOHYS1 VIN_UVLO2 880 Power MOSFET turn-on VUVLOHYS2 VEN_R VEN_HYS IEN_UP IQ_STD IQ mV 3.7 3.9 4.1 V 1.17 500 1.21 1.25 mV V 7 EN = 0, VIN = 5V VIN = 5V, no load 200 11.5 280 250 320 16 VIN = 5V, IOUT = 0.5A, TJ = 25°C 32 40 RDSON VIN = 5V, IOUT = 0.5A, TJ = -40°C to 125°C 32 55 Input discharge resistance RDIS 72 105 Soft-start time TSS VIN_OVP = 6V VIN = 5V, no load, VOUT from 10% to 90% On resistance mV μA μA μA mΩ Ω μs 330 Current Limit Set USB current limit ILIMIT VIN = 5V, VOUT starts to drop VIN = 9V (QC 2.0, 9V mode or QC 3.0, 3.6V ≤ VOUT < 6.6V), VOUT starts to drop VIN = 12V (QC 2.0, 12V mode or QC 3.0, 6.6V ≤ VOUT < 9.8V), VOUT starts to drop 3.05 3.2 3.4 2.51 2.70 2.89 1.87 2.08 2.29 IOUT = 0A, TJ = 25°C IOUT = 0A, TJ = -40°C to 125°C 5.05 5 8.82 11.76 500 5.10 5.10 9 12 5.15 5.2 9.18 12.24 V V V V μA 330 440 mV % A Output Voltage Control Default VIN 9VIN voltage 12VIN voltage VADJ sink current capability VIN_Def1 VIN_Def2 VIN_9 VIN_12 VADJ = 0.8V Line drop compensation Protection VIN_5_C IOUT = 2.4A, only 5VIN active VIN OVP threshold VOV_TH VIN rising edge, VIN = 5V VIN rising edge, VIN = 9V 110 110 115 115 120 120 VIN rising edge, VIN = 12V 110 115 120 VOV_Recovery Reset mode to 5V default 5.35 5.5 5.65 VIN OVP Recovery Threshold MP5032 Rev r1.0 8/4/2017 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2017 MPS. All Rights Reserved. V 4 MP5032 – QC 3.0 CONTROLLER WITH CURRENT-LIMIT SWITCH ELECTRICAL CHARACTERISTICS (continued) VIN = 5V, RILIM = 1.5kΩ, TJ = -40°C to 125°C otherwise noted. Parameter Symbol Condition OCP on time of hiccup OCP off time of hiccup THIC_ON THIC_OFF VOUT