TM
MP8040
High Current Integrated Half Bridge + Driver
The Future of Analog IC Technology
TM
DESCRIPTION
The MP8040 is a general purpose, high frequency half bridge power driver capable of driving a 9A load. The devices integrates both top and bottom N-Channel MOSFET power switches and is fully protected from both sourcing and sinking current by a preset cycle-by-cycle current limit. It has a wide input voltage range from 7.5V to 25V. The MP8040 features a low-current shutdown mode, input under-voltage protection, thermal shutdown, and fault flag signal output. It interfaces with standard logic signals and is available in a small 8-pin SOIC with exposed pad package.
FEATURES
• • • • • • • • • • • • • • ±9A Peak Current Output ±4.25A Continuous Current Output Up to 1.2MHz Switching Frequency Protected Integrated Power 100mΩ Switches All Switches Current Limited Integrated Under-Voltage Protection Integrated Thermal Protection 2.5µA Standby Mode True 2-Quadrant Operation Sources and Sinks Current Fault Indicator Output Class D Audio Driver o 25W/4Ω/10% Output Power Single Ended o 70W/4Ω/10% Output Power Full Bridge Full or Half Bridge DC-DC Switching Regulator Motor Driver
APPLICATIONS
EVALUATION BOARD REFERENCE
Board Number EV0041 Dimensions 3.5”X x 3.5”Y x 1.2”Z
“MPS” and “The Future of Analog IC Technology” are Trademarks of Monolithic Power Systems, Inc.
TYPICAL APPLICATION
VSP
2 7 SP DRV +
FAULT ENABLE PWM SIGNAL
8 6 1
FLT SHDN PWM
MP8040
BS SW 5 3
47nF VOUT
GND 4
MP8040_TAC_S01
MP8040 Rev. 1.5 5/3/2005
www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2005 MPS. All Rights Reserved.
1
TM
MP8040 – HIGH CURRENT INTEGRATED HALF BRIDGE + DRIVER
PACKAGE REFERENCE
TOP VIEW
PWM SP SW GND 1 2 3 4 8 7 6 5 FLT DRV SHDN BS
ABSOLUTE MAXIMUM RATINGS (1)
SP Supply Voltage (VSP).............................. 28V SW Pin Voltage .............................. –0.3V to VSP SW to BS ....................................... –0.3V to +6V Voltage at All Other Pins ............... –0.3V to +6V Storage Temperature .............. –55°C to +150°C
Recommended Operating Conditions
(2)
EXPOSED PAD ON BACKSIDE CONNECT TO PIN 4
MP8040_PD01-SOIC8N
SP Supply Voltage (VSP).................. 7.5V to 24V Peak Output Current...................... 9A Maximum Operating Temperature ............. –40°C to +85°C
Thermal Resistance
Temperature –40°C to +85°C
(3)
SOIC8N .................................. 50 ....... 8.... °C/W
Part Number* MP8040DN * Package SOIC8N (Exposed Pad)
Notes: 1) Exceeding these ratings may damage the device. 2) The device is not guaranteed to function outside of its operating conditions. 3) Measured on approximately 1” square of 1 oz copper.
θJA
θJC
For Tape & Reel, add suffix –Z (eg. MP8040DN–Z) For Lead Free, add suffix –LF (eg. MP8040DN–LF–Z)
ELECTRICAL CHARACTERISTICS
VSP = 12V, VSHDN = 0V, TA = +25°C, unless otherwise noted.
Parameter SP Operating Current SP Shutdown Current SHDN, SP Threshold Low SHDN, SP Threshold High SHDN, SP Input Bias Current SW On Resistance SW Current Limit
(4)
Symbol Condition VSHDN = 2V
Min
Typ 1.5 2.5
Max 2.5 10 1
2 VSP = 7.5V, High-Side and Low-Side VPWM = 5, (Sinking) VPWM = 0, (Sourcing) VPWM = 0 to 2V, 50% Duty Cycle VSP = 7.5V, VPWM = 2V, CSW 100nF, fSW = 3.3KHz VPWM = 0 to 5V VPWM = 0 to 2V, High or Low Pulse VPWM = 0 to 5V VPWM = 5 to 0V TJ Rising, Hysteresis = 20°C 1 0.1 9 9 1.2 99.5 20 200 70 70 160
SW Switching Frequency SW Maximum Duty Cycle
(5)
Units mA µA V V µA Ω A A MHz % ns ns ns ns °C
SW Rise/Fall Time PWM Pulse Width PWM to SW Delay Time Rising PWM to SW Delay Time Falling Thermal Shutdown Temperature (4)
Notes: 4) Guaranteed by design; not production tested. 5) SW drives low for 1.5µs every 300µs to charge the BS to SW capacitor.
MP8040 Rev. 1.5 5/3/2005
www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2005 MPS. All Rights Reserved.
2
TM
MP8040 – HIGH CURRENT INTEGRATED HALF BRIDGE + DRIVER
TYPICAL PERFORMANCE CHARACTERISTICS
Circuit of Figure 4, TA = +25°C, unless otherwise noted.
Delay Time SW Falling (VSP=8V)
Delay Time SW Rising (VSP=8V)
VPWM 2V/div.
VPWM 2V/div.
VSW 5V/div. 10.0ns/div.
MP8040-TPC01
VSW 5V/div. 10.0ns/div.
MP8040-TPC02
Delay Time SW Falling (VSP=25V)
VPWM 2V/div.
Delay Time SW Rising (VSP=25V)
VPWM 2V/div.
VSW 10V/div.
VSW 10V/div.
10.0ns/div.
MP8040-TPC03
10.0ns/div.
MP8040-TPC04
20
THD+N (%)
2 1 0.2 0.1 0.02 0.01 200m
12 10 20 OUTPUT POWER (W)
100
MP8040-TPC05
MP8040 Rev. 1.5 5/3/2005
www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2005 MPS. All Rights Reserved.
3
TM
MP8040 – HIGH CURRENT INTEGRATED HALF BRIDGE + DRIVER
PIN FUNCTIONS
Pin # 1 2 3 4 5 6 7 8 Name PWM SP SW GND BS SHDN DRV FLT Description Driver Logic Input. Drive PWM with the signal that controls the MP8040 output. Drive PWM high to turn on the high-side switch; drive PWM low to turn on the low-side switch. Power Supply Input. Connect SP to the positive side of the input power supply. Bypass SP to GND as close to the IC as possible. Switched Output. SW is the power output of the MP8040. Connect the output LC filter to SW. SW is valid approximately 100µs after SP goes high. Ground. (Note: Connect the exposed pad on the bottom side to Pin 4). Bootstrap Supply. BS powers the high-side gate of the MP8040. Connect a 0.1µF or greater capacitor between BS and SW. Shutdown Input. SHDN enables/disables the MP8040. Drive SHDN low to turn on the MP8040, drive it high to turn it off. If not used, connect SHDN to GND. Gate Drive Supply Bypass. The voltage at DRV is supplied from an internal regulator from SP. DRV powers the internal circuitry and internal MOSFET gate drives. Bypass DRV to GND with a 0.1µF to 10µF capacitor. Fault Output. Active-low, open drain. A low output at FLT indicates that the MP8040 has detected a fault and has shutdown. Connect FLT to DRV through a 100kΩ resistor.
OPERATION
The MP8040 is a general purpose, power driver. It takes a logic input and drives a half bridge comprised of 0.1Ω high-side and low-side N-Channel MOSFET switches. It operates at frequencies up to 1.2MHz, can accept a DC supply voltage as high as 25V, and produce peak output current as high as 9A.
5 BS DBS BS UVLO
INTERNAL 5V REG. CURRENT LIMIT & FEEDBACK THERMAL SHUTDOWN UVLO
2 SP
DRV
7 HI DRIVE
PWM
1
LOGIC
3 SW
FLT SHDN
8
LO DRIVE
6
4 GND
MP8040_F02
Figure 1—Function Block Diagram
MP8040 Rev. 1.5 5/3/2005 www.MonolithicPower.com MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. © 2005 MPS. All Rights Reserved.
4
TM
MP8040 – HIGH CURRENT INTEGRATED HALF BRIDGE + DRIVER
SW Output The SW output drives the load. It is controlled by the logic input signal at PWM. When the signal at PWM is high (above 2V), the high-side switch is turned on. When the signal at PWM is low (less than 0.4V), the low-side switch is turned on. The MP8040 uses internal N-Channel MOSFETs for both the high-side and low-side switches. The high-side MOSFET gate drive is powered from the voltage between SW and BS, allowing BS to rise above the SP input voltage to power the high-side MOSFET. To do this a bootstrap capacitor is connected between SW and BS. When the low-side switch is on, the capacitor is internally charged from the voltage at DRV, which is also internally generated. There is a dead time region (typically 40ns) where both the upper and lower switches are off (see Figure 2). Both the high-side and low-side switches have internal current limits to prevent failure due to excessive load current. Once the current limit is reached, both output switches are turned off and the fault output is asserted (driven low). Shutdown The MP8040 includes a 2.5µA shutdown mode. When SHDN is high, both output switches are turned off and the input current drops to 2.5µA. When the MP8040 is shutdown, the internally generated voltage at DRV drops to 0V, and the fault output (FLT) is asserted (driven low). If the shutdown mode is not used, connect SHDN directly to GND. Fault Output The MP8040 includes a fault indicator output (FLT). This is an active-low open drain output. The MP8040 detects faults due to over-current (>9A), over-temperature (>160°C), undervoltage at SP (
很抱歉,暂时无法提供与“MP8040DN”相匹配的价格&库存,您可以联系我们找货
免费人工找货