ADC405

ADC400 SERIES 1W, Ultra-High Isolation SIP, Single & Dual Output DC/DC Converters Selection Guide Model Number ADC401 ADC402 ADC403 ADC404 ADC405 ADC406 ADC411 5 (4.5 - 5.5) Input Voltage VDC Output Voltage VDC 5 12 15 ±5 ±12 ±15 5 12 12 (10.8 - 13.2) 15 ±5 ±12 ±15 Output Current mA 200 80 65 ±100 ±40 ±35 200 80 65 ±100 ±40 ±35 Efficiency % Typ. 66 66 66 66 72 73 66 66 66 66 74 75 Load Regulation % Max. 10 8 8 10 8 8 10 8 8 10 8 8 Key Features • • • • • • • • • • Efficiency up to 75% 6000VDC Isolation MTBF > 2,000,000 Hours Low Cost Input 5 and 12VDC Output 5, 12, 15, ±5, ±12 and ±15VDC Temperature Performance -25°C to +70°C UL 94V-0 Package Material Internal SMD Construction Industry Standard Pin-out ADC412 ADC413 ADC414 ADC415 ADC416 MPS Industries ADC400 1W DC/DC's are specially designed to provide ultra-high levels of isolation 6000VDC in a miniature SIP package. The series consists of 12 models with input voltages of 5V and 12VDC which offers standard output voltages of 5V, 12V, 15VDC in both single and dual output configurations. The ADC400 series is an excellent selection for a variety of applications including distributed power systems, mixed analog/digital subsystems, portable test equipments, local power networks and battery backed systems. Mechanical Dimensions 22.0 [0.87] Pin Connections Pin 1 2 5 12.5 [0.49] Singles +Vin -Vin -Vout No Pin +Vout Duals +Vin -Vin -Vout Common +Vout 0.5 [0.02] 6 7 Case Size – 3.5 [0.14] 21.0 [0.83] 2.54 [0.100] 3.5 [0.14] 22.0x7.5x12.5mm (0.87x0.30x0.49inch) Case Material – 7.5 [0.30] 1 2 5 6 7 Non-Conductive Black Plastic Weight – 3.9g (0.14Oz) Tolerance Millimeters X.X±0.25 X.XX±0.13 Pin ±0.05 Inches X.XX±0.01 X.XXX±0.005 ±0.002 2463 208th Street, Ste. 205 Torrance, CA 90501 Tel: (310) 533-1455 Fax: (310) 533-1853 0.25 [0.010] 2.0 [0.08] 0.50 [0.020] http://www.mpsind.com E-mail: sales@mpsind.com ADC400 SERIES 1W, Ultra-High Isolation SIP, Single & Dual Output DC/DC Converters Absolute Maximum Ratings Parameter Input Surge Voltage (1000mS) 5VDC Input Models 12VDC Input Models General Characteristics Min. -0.7 -0.7 ----- Max. Units 9 18 260 650 VDC VDC °C mW Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency MTBF Conditions 60 Seconds 500VDC 100kHz, 1V Min. 6000 10 --50 Typ. ----15 80 --- Max. ----20 100 --- Units VDC GΩ pF kHz MHrs Lead Temperature (1.5mm from case for 10sec.) Internal Power Dissipation Exceeding the unit absolute maximum ratings could cause damage. These are not continuous operating ratings. MIL-HDBK-217F @25°C Ground Benign 2 Environmental Characteristics Parameter Operating Temperature Operating Temperature Storage Temperature Humidity Cooling Output Characteristics Max. Units 70 90 125 °C °C °C % Parameter Line Regulation Load Regulation Ripple & Noise Short Circuit Conditions For Vin Change of 1% Io = 20% to 100% 20MHz BW Min. --Typ. ±1.2 Max. ±1.5 Units % % mV P-P Conditions Ambient Case Min. -25 -25 -40 See Selection Guide --100 150 --95 Free-Air Convection 0.5 Second Max. Maximum Capacitive Load Models by Output Voltage (Each Output on Duals) Singles 680 Duals 220 Units uF Derating Curve 100 80 Output Power (%) 100LFM 200LFM 400LFM Notes: 1. Specifications typical at Ta=+25°C, resistive load, nominal input voltage, rated output current unless otherwise noted. 2. These power converters require a minimum output load to maintain specified regulation. 3. Operation under no-load conditions will not damage these modules; however, they may not meet all specifications listed. 4. All DC/DC converters should be externally fused at the front end for protection. 5. Other input and output voltage may be available, please contact factory. 6. All specifications subject to change without notice. 7. For detailed data sheet, please visit our website. 60 Natural convection 40 20 0 -25 ¡ã 50 60 70 80 ] 90 100 110 Ambient Temperature 2463 208th Street, Ste. 205 Torrance, CA 90501 Tel: (310) 533-1455 Fax: (310) 533-1853 http://www.mpsind.com E-mail: sales@mpsind.com