P191-202-1

PASSIVE POWER FACTOR CORRECTION INDUCTORS P191 SERIES • • • • • • • Design for power factor correction with high flux density material 20% to 50% smaller than traditional designs Switching Frequency: 32KHz Min. AC Line Voltage: 265Vac Max. High Frequency 200 kHz – 700 kHz Operating Temperature: -40°C to +130°C Custom Design Available ELECTRICAL PARAMETERS @ 25°C Part Number P191301-1 501-1 751-1 102-1 152-1 202-1 301-2 501-2 751-2 102-2 152-2 202-2 301-3 501-3 751-3 102-3 152-3 301-5 501-5 751-5 102-5 152-5 301-7 501-7 751-7 102-7 L (μH ±15%) 300 500 750 1000 1500 2000 300 500 750 1000 1500 2000 300 500 750 1000 1500 300 500 750 1000 1500 300 500 750 1000 RDC (Ω MAX) 0.50 0.65 0.90 1.20 1.20 2.00 0.32 0.40 0.60 0.80 0.85 0.95 0.20 0.30 0.32 0.40 0.43 0.10 0.15 0.18 0.20 0.26 0.06 0.10 0.13 0.18 IDC (A) 1.0 1.0 1.0 1.0 1.0 1.0 2.0 2.0 2.0 2.0 2.0 2.0 3.0 3.0 3.0 3.0 3.0 5.0 5.0 5.0 5.0 5.0 7.0 7.0 7.0 7.0 DIM A Max (mm) 21.0 21.0 23.0 25.0 27.5 29.0 26.0 29.0 31.0 32.0 34.0 34.0 30.0 31.0 34.0 36.0 43.0 35.0 42.0 47.0 49.0 55.0 45.0 51.0 57.0 57.0 DIM B Max (mm) 11.0 11.0 12.5 11.0 12.5 13.5 12.0 14.0 17.0 18.0 19.0 19.0 15.0 16.5 18.0 20.0 21.0 20.0 17.0 21.0 23.0 25.0 23.0 26.0 27.0 27.0 DIM C Nom (mm) 9.0 9.0 10.0 9.0 10.5 11.0 10.0 11.0 13.0 14.0 15.5 15.5 11.5 12.5 15.5 16.0 16.0 16.0 15.0 18.0 19.0 20.0 18.0 20.0 21.0 21.0 DIM D Nom (mm) 18.0 18.0 20.0 22.5 25.0 26.0 23.0 26.0 28.0 29.0 30.0 30.0 26.5 27.5 31.0 32.0 39.0 31.5 37.5 43.5 45.0 51.5 39.0 46.0 52.5 52.5 DIM E Nom (mm) 0.40 0.40 0.40 0.40 0.40 0.40 0.60 0.60 0.60 0.60 0.60 0.60 0.80 0.80 0.80 0.80 0.80 1.00 1.00 1.00 1.00 1.00 1.30 1.30 1.30 1.30 Product performance is limited to specified parameters. Data is subject to change without prior notice. Tel: 310-325-1043 Fax: 310-325-1044 www.mpsind.com sales@mpsind.com PASSIVE POWER FACTOR CORRECTION INDUCTORS P191 SERIES ELECTRICAL PARAMETERS @25°C Part Number P191301-10 501-10 751-10 102-10 L (μH ±15%) 300 500 750 1000 RDC (Ω MAX) 0.05 0.06 0.08 0.09 IDC (A) 10.0 10.0 10.0 10.0 DIM A Max (mm) 53.0 63.0 73.0 77.0 DIM B Max (mm) 27.0 31.0 32.0 36.0 DIM C Nom (mm) 21.0 24.0 26.0 28.0 DIM D Nom (mm) 47.0 55.0 68.0 70.0 DIM E Nom (mm) 1.73 1.73 1.73 1.73 NOTES: • Inductance test @ 10KHz, 0.1VRMS • IDC: 10% roll off Typ (20% Max.) from initial inductance value • Add -V for Vertical Mount, -H for Horizontal Mount, -W for Hook Up wire • Extended length hook up wire with Fast-On available on request DIMENSIONS (mm) Product performance is limited to specified parameters. Data is subject to change without prior notice. Dimensions Unless otherwise specified, all tolerances are: inch: .XX : ±0.015 .XXX : ±0.004 mm: X,X : ±0,38 X,XX : ±0,10 Tel: 310-325-1043 Fax: 310-325-1044 www.mpsind.com sales@mpsind.com