BFL2805E

ISO 9001 CERTIFIED BY DSCC 5A EMI FILTER M.S.KENNEDY CORP. 4707 Dey Road Liverpool, N.Y. 13088 BFL2805 (315) 701-6751 FEATURES: Replaces APEX FDB461 All Ceramic Capacitors Surface Mount Magnetics -55°C to +125°C Operation 60dB Minimum Differential Mode Rejection at 500KHz 5.5 Amps Throughput Current Meets MIL-STD-461C CEO3 Standards For BBF2800 Series DC to DC Converters MIL-STD-704 (A Through E) Power Bus Compatibility MIL-PRF-38534 CERTIFIED DESCRIPTION: The BFL2805 is a high reliability EMI filter for use with BBF2800 series of DC-DC converters. This filter has been designed to reduce the input line reflected ripple current to within the limit of MIL-STD-461C, CE03. The BFL2805 hybrid EMI filter utilizes all ceramic capacitors, surface mount magnetics and ultrasonically bonded aluminum wires to provide reliable operation at all operating temperatures while surviving very high G forces. The stand-alone filter's internal components are all passive devices and selected to operate from input voltages up to and including the peak transient voltage. The filter therefore does not require or utilize transient supression circuitry and is compatible with the transient specification of a MIL-STD-704 type power bus. When connected to an output device, the output device must be able to operate from compatible voltages. The filter will attenuate spikes, but the duration and magnitude of the spike must be within the operating range of the filter. The 12-pin high power dip package allows connection to a heatsink, is hermetically sealed and is isolated from the internal circuits. Heat sinking is recommended for full power operation at elevated ambient temperatures. EQUIVALENT SCHEMATIC TYPICAL APPLICATIONS Airborne Power Systems Aerospace Power Systems Vehicle Electrical Systems Ground Equipment and Test Equipment 1 2 3 4 5 6 1 PIN-OUT INFORMATION +VIN INPUT COMMON NC NC NC NC 12 11 10 9 8 7 NC NC NC CASE GROUND +VOUT OUTPUT COMMON Rev. B 10/05 ABSOLUTE MAXIMUM RATINGS ○ ○ ○ ○ ○ ○ ○ 6 ELECTRICAL SPECIFICATIONS Parameter Input Voltage 1 Input Current 1 Output Voltage 2 Output Current 1 Test Conditions Steady State Transient 50µsec. MAX DC Steady State Ripple Steady State Steady State f=200KHz f=500 KHz f=1MHz f=5MHz Subgroups Min. BFL2805H/E Typ. 28 V OUT=V IN-Iin(R DC ) 0.20 50 65 70 73 Max. Min. 50 80 5.5 0.3 5.5 0.35 4.7 0 40 60 60 60 100 0 40 60 60 60 100 BFL2805 Typ. 28 V OUT=V IN-Iin(R DC ) 0.20 50 65 70 73 Max. 50 80 5.5 0.3 5.5 1,2,3 1 1 1 1 1 4 4 4 4 7 7 DC Resistance (RDC) Noise Reduction Capacitance 1 Isolation Any Pin to Case Any Pin to Case NOTES: 1 2 3 4 5 This parameter is guaranteed by design but need not be tested. Typical parameters are representative of actual device performance but are for reference only. Industrial grade and "E" suffix devices shall be tested to subgroup 1,4 and 7 unless otherwise specified. Military grade devices ('H' suffix) shall be 100% tested to subgroups 1,2,3,4 and 7. Subgroup 1,4,7 TA = TC = +25°C Subgroup 2 TA = TC = +125°C Subgroup 3 TA = TC = -55°C 6 Continuous operation at or above absolute maximum ratings may adversely effect the device performanc and/or life cycle. 2 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Input Voltage Range Input Voltage Transient Voltage (any pin to case pin 9) Storage Temperature Range Lead Temperature (10 Seconds Soldering) ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 0-50VDC 80V @ 50mS 500V -65°C to +150°C 300°C Case Operating Temperature Range BFL2805H/E -55°C to +125°C BFL2805 -40°C to+85°C Units V V A Vdc A rms A dB dB dB dB µF MOhm 0.35 Ohms 4.7 - Rev. B 10/05 TYPICAL PERFORMANCE CURVES BBF2803S CONVERTER WITH BFL2805 EMMISION LEVEL dB µA EMMISION LEVEL dB µA FREQUENCY (MHz) BBF2805S CONVERTER WITH BFL2805 FREQUENCY (MHz) BBF2812S CONVERTER WITH BFL2805 EMMISION LEVEL dB µA EMMISION LEVEL dB µA BBF2815S CONVERTER WITH BFL2805 FREQUENCY (MHz) FREQUENCY (MHz) TYPICAL APPLICATION 3 Rev. B 10/05 MECHANICAL SPECIFICATIONS WEIGHT = 67 GRAMS TYPICAL ESD Triangle Indicates Pin 1. NOTE: ALL DIMENSIONS ARE ±.010 INCHES UNLESS OTHERWISE LABELED. ORDERING INFORMATION BFL2805 H SCREENING BLANK= INDUSTRIAL; E = EXTENDED RELIABILITY; H= MIL-PRF-38534 CLASS H OUTPUT CURRENT 05=5 AMP NOMINAL INPUT VOLTAGE GENERAL PART NUMBER The above example is a Military grade 5 Amp EMI filter. M.S. Kennedy Corp. 4707 Dey Road, Liverpool, New York 13088 Phone (315) 701-6751 FAX (315) 701-6752 www.mskennedy.com The information contained herein is believed to be accurate at the time of printing. MSK reserves the right to make changes to its products or specifications without notice, however, and assumes no liability for the use of its products. Please visit our website for the most recent revision of this datasheet. 4 Rev. B 10/05