K1700A

K1700A Series 5V Temperature Compensated Voltage Controlled Crystal Oscillators ! Applications: Phase Lock Loops Clocking “Sync” to NTSC Video Standards; Reference Signal; Signal Tracking; ATM ! 2.0 to 35.0 MHz Frequency Range ! ±10ppm Frequency Stability - (0oC to 70oC) K1710 ! ±20ppm Frequency Stability - (-40oC to 85oC) K1720 ! -40°C to 85°C Operating Temperature ! TTL/CMOS Compatible ! Meets Stratum IV Stability Requirements ! Hermetically Sealed Package ax. mM 8m 20, ax. mM 2m 13, CZ E X0A K170.000 MH E COD 2 TI DAT C m 9m 7,4 x. Ma PIN 1 E L E C T R I C A L S P E C I F I C AT I O N S Model Frequency Range (MHz) Input Current (mA) Frequency Control Function Deviation (ppm) Minimum (ppm) Maximum Linearity (%) Modulation Bandwidth (±3dB) Nominal Control Voltage (V) Control Voltage Range (V) Transfer Function Input Impedance Frequency Stability (ppm) Overall 0oC to 70oC -40oC to 85oC Aging, 10 Years Temperature Range (oC) Operating Storage Supply Voltage (V) Symmetry CMOS/TTL Start Up Time (ms) Typical SSB Phase Noise (dBC/Hz) Offset from Carrier 10Hz 100Hz 1KHz 10KHz 100KHz 0oC to +70oC -40oC to +85oC +5.0V ±5% 45/55 < 16MHz; 40/60 ≥ 16MHz 20KHz 2.5 0.5 to 4.5 Positive > 50KΩ @ 10KHz K1710AC 2.0 to 35 < 30 (For Custom Deviation Range, Vc Range, etc. - Consult Factory) K1720ACM PA R T N U M B E R I N G G U I D E K17X0AX - Specify Frequency “Blank” = 0°C to 70°C Operating Temp. “M” = -40°C to +85°C Operating Temp. K1720 Only “1” = ±10ppm, 0°C to 70°C Operating Temp. “2” = ±20ppm, -40°C to +85°C Operating Temp. 2553 N. Edgington Street, Franklin Park, IL 60131 " Phone: 847.451.1000 " Fax: 847.451.7585 800-888-1499 or www.champtech.com 1 K1700A Series 5V Temperature Compensated Voltage Controlled Crystal Oscillators PIN 1 7 8 14 FUNCTION Voltage Control Gnd/ & Case Gnd Output + VCC SHIPPING TUBE CROSS SECTION OUTPUT WAVEFORM TEST CIRCUIT DIAGRAM MECHANICAL AND ENVIRONMENTAL SPECIFICATIONS TEST METHODS Temperature Cycle Mechanical Shock Vibration Humidity Steady State Thermal Shock Electrostatic Discharge Solderability Hermeticity Resistance to Soldering Lead Integrity Marking Permanence Life Test REFERENCE PROCEDURES MIL-STD-833, Mtd 1010, Cond. B MIL-STD-883, Mtd 2002, Cond. B MIL-STD 883, Mtd 2007, Cond. B MIL-STD-202, Mtd 103 MIL-STD-883, Mtd 1011.7 Cond. B MIL-STD-883, Mtd 3015 Class II MIL-STD-883, Mtd 2022.2 MIL-STD-883, Mtd 1014.8, Cond. A1 DESCRIPTION -55°C to +125°C; Air-to-Air; 100 cycles; 10 min. dwell 1500 g’s 20-2000 Hz; 0.06 inch; 15g’s; 3 planes 40°C; 90%-95% R.H.; 56 days 100°C to 0°C; Water-to-Water; 15 cycles 2 KV to 4 KV Threshold Solder dip; Meniscograph Criteria Mass spectro. 2 x 10-8 atmos. CC/sec He MIL-STD-202, Mtd 210A, Cond. C 260°C; 10 seconds: 1 inch/sec. MIL-STD-883, Mtd 2004.5, Cond. A, B1 Lead tension & bend stress MIL-STD-883, Mtd 2015.8 MIL-STD-883, Mtd 1005.6 Resistance to solvents 125°C, powered, 1000 hours minimum 2553 N. Edgington Street, Franklin Park, IL 60131 " Phone: 847.451.1000 " Fax: 847.451.7585 800-888-1499 or www.champtech.com 2