Reference Only
1 / 12
Spec No.J(E)TE243C-0106-01
参考図 Reference Specification
5CCEG
型名 TYPE
試作番号 Sample Number
外観寸法
Physical Dimensions
*1
Marking
③
⑤
②
⑥
0.9
0.6±0.15
5.7
*2
④
(φ3.1±0.1)
5.6
6.2
3.4
3.6
5.6
(0.6x1.1)
#A1313B-0029GGH=P3
①
0.15 max.
0.15 max.
1.2
*1 はんだのつらら部分の寸法は含まない。
Dimension of solder tip is not included.
*2 巻線のからげ部分の寸法は含まない。
Dimension of wiring part of terminal pin is not included.
一般寸法公差 ±0.3 単位 mm
Tolerance
Unit
始動トルク Starting Torque
1~20 mN・m
接続(底面図) Connection(Bottom View)
巻線仕様 Turn
端子番号
3-1
6-4
S③
Pin
④
巻 数
②
⑤
5 1/2
3 1/2
Turns
①
⑥ S
線径線種
φ0.1-2UEW
Wire
電気的性能 Electrical Characteristics
a.使用周波数
Using Frequency
b.(C)共振容量可変範囲( 3-1 )間
Range/Tolerance
c.Q
( 3-1 )間
100
MHz
11.4 pF ± 3 % 以上 (測定周波数
100
min/max(Measuring Frequency)
無負荷Q: 72±20%
(測定周波数
100
Unloaded
(Measuring Frequency)
MHz)
MHz)
※インダクタンスLは上記の共振容量Cからの換算
L inductance is conversion value, from C resonant capacitor.
換算式 Conversion formula: L
1
( 2F ) 2 C
C=共振容量 Resonant Capacitor F=使用周波数 Using Frequency
※Q及びCはノミナルコイルを基準とする
Q&C Consider nominal coil as a standard.
使用温度範囲 Operating Temperature
-40℃~85℃
標準試験状態 Standard Measurement Condition
特に指定のない限りは、常温(5~35℃)常湿(45~85%)のもとで行う。
但し、判定に疑義が生じた時は温度20±2℃、湿度65±5%にて試験を行い判定する。
Unless otherwise specified, measurements are conducted under temperature at 5 to 35℃, humidity at 45 to 85%.
If there is any doubt about the result, measurement shall be conducted under temperature at 20±2℃, humidity at 65
±5%.
MURATA MFG.CO., LTD
Reference Only
2 / 12
Spec No.J(E)TE243C-0106-01
参考図 Reference Specification
5CCEG
型名 TYPE
試作番号 Sample Number
外観寸法
Physical Dimensions
*1
Marking
③
⑤
②
⑥
0.9
0.6±0.15
5.7
*2
④
(φ3.1±0.1)
5.6
6.2
3.4
3.6
5.6
(0.6x1.1)
#A1313B-0030GRG=P3
①
0.15 max.
0.15 max.
1.2
始動トルク Starting Torque
*1 はんだのつらら部分の寸法は含まない。
Dimension of solder tip is not included.
*2 巻線のからげ部分の寸法は含まない。
Dimension of wiring part of terminal pin is not included.
一般寸法公差 ±0.3 単位 mm
Tolerance
Unit
1~20 mN・m
接続(底面図) Connection(Bottom View)
S ③
④
②
⑤
①
⑥ S
巻線仕様 Turn
端子番号
3-1
3-5
Pin
巻 数
5 1/2 2 3/4
Turns
線径線種
φ0.07-2UEW
Wire
5-1
6-4
2 3/4
3 1/2
電気的性能 Electrical Characteristics
a.使用周波数
Using Frequency
b.(C)共振容量可変範囲( 3-1 )間
Range/Tolerance
c.Q
( 3-1 )間
100
MHz
11.4 pF +5/-2 % 以上 (測定周波数
100
min/max(Measuring Frequency)
無負荷Q: 61±20%
(測定周波数
100
Unloaded
(Measuring Frequency)
MHz)
MHz)
※インダクタンスLは上記の共振容量Cからの換算
L inductance is conversion value, from C resonant capacitor.
換算式 Conversion formula: L
1
( 2F ) 2 C
C=共振容量 Resonant Capacitor F=使用周波数 Using Frequency
※Q及びCはノミナルコイルを基準とする
Q&C Consider nominal coil as a standard.
使用温度範囲 Operating Temperature
-40℃~85℃
標準試験状態 Standard Measurement Condition
特に指定のない限りは、常温(5~35℃)常湿(45~85%)のもとで行う。
但し、判定に疑義が生じた時は温度20±2℃、湿度65±5%にて試験を行い判定する。
Unless otherwise specified, measurements are conducted under temperature at 5 to 35℃, humidity at 45 to 85%.
If there is any doubt about the result, measurement shall be conducted under temperature at 20±2℃, humidity at 65
±5%.
MURATA MFG.CO., LTD
Reference Only
3 / 12
Spec No.J(E)TE243C-0106-01
参考図 Reference Specification
5CCEG
型名 TYPE
試作番号 Sample Number
外観寸法
Physical Dimensions
*1
Marking
③
⑤
②
⑥
0.9
0.6±0.15
3.4
5.7
*2
④
(φ3.1±0.1)
5.6
6.2
3.6
5.6
(0.6x1.1)
#A1313B-0031GRG=P3
①
0.15 max.
0.15 max.
1.2
始動トルク Starting Torque
*1 はんだのつらら部分の寸法は含まない。
Dimension of solder tip is not included.
*2 巻線のからげ部分の寸法は含まない。
Dimension of wiring part of terminal pin is not included.
一般寸法公差 ±0.3 単位 mm
Tolerance
Unit
1~20 mN・m
接続(底面図) Connection(Bottom View)
S ③
④
②
⑤
①
⑥ S
巻線仕様 Turn
端子番号
3-1
3-5
Pin
巻 数
5
2 1/2
Turns
線径線種
φ0.07-2UEW
Wire
5-1
6-4
2 1/2
3
電気的性能 Electrical Characteristics
a.使用周波数
Using Frequency
b.(C)共振容量可変範囲( 3-1 )間
Range/Tolerance
c.Q
( 3-1 )間
100
MHz
11.4 pF +2/-4 % 以上 (測定周波数
100
min/max(Measuring Frequency)
無負荷Q: 54±20%
(測定周波数
100
Unloaded
(Measuring Frequency)
MHz)
MHz)
※インダクタンスLは上記の共振容量Cからの換算
L inductance is conversion value, from C resonant capacitor.
換算式 Conversion formula: L
1
( 2F ) 2 C
C=共振容量 Resonant Capacitor F=使用周波数 Using Frequency
※Q及びCはノミナルコイルを基準とする
Q&C Consider nominal coil as a standard.
使用温度範囲 Operating Temperature
-40℃~85℃
標準試験状態 Standard Measurement Condition
特に指定のない限りは、常温(5~35℃)常湿(45~85%)のもとで行う。
但し、判定に疑義が生じた時は温度20±2℃、湿度65±5%にて試験を行い判定する。
Unless otherwise specified, measurements are conducted under temperature at 5 to 35℃, humidity at 45 to 85%.
If there is any doubt about the result, measurement shall be conducted under temperature at 20±2℃, humidity at 65±
5%.
MURATA MFG.CO., LTD
Reference Only
4 / 12
Spec No.J(E)TE243C-0106-01
参考図 Reference Specification
5CCEG
型名 TYPE
#A1313B-0032GGH=P3
試作番号 Sample Numbe
外観寸法
Physical Dimensions
③
⑤
②
⑥
0.9
0.6±0.15
3.4
5.7
*2
④
(φ3.1±0.1)
5.6
6.2
3.6
5.6
(0.6x1.1)
*1
Marking
①
0.15 max.
0.15 max.
1.2
始動トルク Starting Torque
*1 はんだのつらら部分の寸法は含まない。
Dimension of solder tip is not included.
*2 巻線のからげ部分の寸法は含まない。
Dimension of wiring part of terminal pin is not included.
一般寸法公差 ±0.3 単位 mm
Tolerance
Unit
1~20 mN・m
接続(底面図) Connection(Bottom View)
S③
④
②
⑤
①
⑥ S
巻線仕様 Turn
端子番号
3-1
6-4
Pin
巻 数
5 1/2
3
Turns
線径線種
φ0.1-2UEW
Wire
電気的性能 Electrical Characteristics
a.使用周波数
Using Frequency
b.(C)共振容量可変範囲( 3-1 )間
Range/Tolerance
c.Q
( 3-1 )間
100
MHz
11.7 pF ± 3 % 以上 (測定周波数
100
min/max(Measuring Frequency)
無負荷Q: 72±20%
(測定周波数
100
Unloaded
(Measuring Frequency)
MHz)
MHz)
※インダクタンスLは上記の共振容量Cからの換算
L inductance is conversion value, from C resonant capacitor.
換算式 Conversion formula: L
1
( 2F ) 2 C
C=共振容量 Resonant Capacitor F=使用周波数 Using Frequency
※Q及びCはノミナルコイルを基準とする
Q&C Consider nominal coil as a standard.
使用温度範囲 Operating Temperature
-40℃~85℃
標準試験状態 Standard Measurement Condition
特に指定のない限りは、常温(5~35℃)常湿(45~85%)のもとで行う。
但し、判定に疑義が生じた時は温度20±2℃、湿度65±5%にて試験を行い判定する。
Unless otherwise specified, measurements are conducted under temperature at 5 to 35℃, humidity at 45 to 85%.
If there is any doubt about the result, measurement shall be conducted under temperature at 20±2℃, humidity at 65±
5%.
MURATA MFG.CO., LTD
Reference Only
5 / 12
Spec No.J(E)TE243C-0106-01
5CCEG Type
項
目
信頼性試験項目一覧
Item
1.耐熱性
High Temp
Exposure(Storage)
規
格
Reliability Test Item List [1/2]
Specifications
L変化率±2.0%以内
Q変化率± 20%以内
Inductance : within±2.0%
Unloaded Q : within±20%
AEC-Q200 Test No.3
2.温度サイクル
Temperature
cycling
L変化率±2.0%以内
Q変化率± 20%以内
Inductance : within±2.0%
Unloaded Q : within±20%
AEC-Q200 Test No.4
3.耐湿性
Biased Humidity
AEC-Q200 Test No.7
4.耐薬品性試験
Resistance to
Solvent
AEC-Q200 Test
No.12
5.耐衝撃性
Mechanical Shock
AEC-Q200 Test
No.13
6.耐振性
Vibration
AEC-Q200 Test
No.14
7.はんだ耐熱性
Resistance to
soldering heat
AEC-Q200 Test
No.15
8.ESD 試験 (HBM)
ESD
AEC-Q200 Test
No.17
L変化率±2.0%以内
Q変化率± 20%以内
Inductance : within±2.0%
Unloaded Q : within±20%
条
件
Conditions
温度+85±3℃中に 1000時間放置後、常温常湿中に放
置し、24±4時間以内に測定。
The specimen shall be stored at a temperature
of 85±3℃ for 1000 h. Then it shall be
stabilized under standard atmospheric
conditions.
Measurement shall be made within 24±4 h.
-40℃(30分)→+85℃(30分) 1サイクルを 1000サイクル行い常
温常湿中に放置し、24±4時間以内に測定。
The specimen shall be subjected to 1000
continuous cycles of temperature change of -40
℃ for 30 min and +85℃ for 30 min. Then it
shall be stabilized under standard atmospheric
conditions.
Measurement shall be made within 24±4 h.
温度+85℃、湿度 85%中に 1000 時間放置後、
常温常湿中に放置し、24±4 時間以内に測定。
The specimen shall be stored at a temperature
of 85℃ with relative humidity of 85% for 1000
h. Then it shall be stabilized under standard
atmospheric conditions.
Measurement shall be made within 24±4 h.
L変化率±1.0%以内
Q変化率± 20%以内
Inductance : within±1.0%
Unloaded Q : within±20%
イソプロピルアルコール(25±5℃)中に3分間浸し
1時間放置後、測定。
Immerse in Isopropyl-Alcohol for 3 minutes at
25±5°C.
Measurement shall be made within 1h.
L変化率±1.0%以内
Q変化率± 20%以内
Inductance : within±1.0%
Unloaded Q : within±20%
MIL-STD-202 Method 213 Condition C に従う
Base on MIL-STD-202 Method 213 Condition C.
L変化率±1.0%以内
Q変化率± 20%以内
Inductance : within±1.0%
Unloaded Q : within±20%
周波数範囲10~2000Hz、加速度5G、掃引の割合が20
分間の振動を互いに垂直な3方向に各4時間加える。
10~2000Hz, Amplitude 5g for 20 minutes.
for 4 hours in each of 3(X, Y, Z) axes.
L変化率±2.0%以内
Q変化率± 20%以内
Inductance : within±2.0%
Unloaded Q : within±20%
MIL-STD-202 Method 210 Condition K に従う
ピーク温度 255℃
Base on MIL-STD-202 Method 210 Condition K.
Peak temp 255℃.
L変化率±1.0%以内
Q変化率± 20%以内
Inductance : within±1.0%
Unloaded Q : within±20%
AEC-Q200-002 に従う
Base on AEC-Q200-002
MURATA MFG.CO., LTD
Reference Only
6 / 12
Spec No.J(E)TE243C-0106-01
5CCEG Type
項
目
Item
9.はんだ付け性
Solderability
AEC-Q200 Test
No.18
10.たわみ強度
Board Flex
AEC-Q200 Test
No.21
11.固着強度
Terminal Strength
(SMD)
信頼性試験項目一覧
規
格
Reliability Test Item List [2/2]
Specifications
条
件
Conditions
浸漬した電極面の 95%以上が新し
いはんだで覆われている事。
New solder coverage to be over
95%.
J-STD-002 に従う。
Base on J-STD-002
SMD: c) J-STD-002 Method
L変化率±1.0%以内
Q変化率± 20%以内
Inductance : within±1.0%
Unloaded Q : within±20%
AEC-Q200-005に従う。
曲げ幅2mm以上、60秒以上保持。
Base on AEC-Q200-005
2mm (Min). 60 sec minimum holding time.
L変化率±1.0%以内
Q変化率± 20%以内
Inductance : within±1.0%
Unloaded Q : within±20%
AEC-Q200-006に従う。
17.7Nの荷重を加え60±1秒保持する。
Base on AEC-Q200-006
17.7N / 60±1 sec.
AEC-Q200 Test
No.22
MURATA MFG.CO., LTD
D category 3 @ 260°C.
Reference Only
7 / 12
Spec No.J(E)TE243C-0106-01
テーピング仕様
TAPING SPECIFICATIONS
5CCEG TYPE
【テープ寸法図・TAPE DETAILS】
+0.1
±0.2
±0.1
12
1.75
±0.1
±0.2
6.2
16
±0.4
7.5
±0.2
6.6
(13.5)
±0.2
4
2
±0.2
φ -0
1.5
±0.2
シールテープ
Fixing
seal tape
6.2
【部品装着図・TAPING METHOD】
引出方向
Pulling
direction
①
②
③
⑥
⑤
④
上面図
Top view
取付電極面
Electrode
(記事・Note)
1.装着テープの材料は、
ポリスチレンとする。
Carrier tape material shall
be Polystyrene.
2.シールテープの材質は、
ポリエチレンおよび
ポリエチレンテレフタ
レートとする。
Fixing seal tape material
shall be Polyethylene or
Polyethylene Terephthalate.
3.シールテープは送り穴を
ふさいだり、装着テープ
からはみ出したりして
いないこととする。
Fixing seal tape shall
neither cover feed hole
nor bulge out of carrier
tape.
4.シールテープ剥離強度
0.2~0.7N 以内
The range of the force to
peel away the fixing seal
tape shall be ;
Min. 0.2N , Max. 0.7N
(記事・Note)
1.部品の挿入は、取付け電極を
下面とする。
また引き出し方向は左図とする。
Electrode shall be packaged in
the tapes upside down against
fixing seal tape.
Pulling direction of tape
refer to this picture.
引出方向
2.部品装着部の前後には
Pulling
direction
各々30ピッチ以上の空部
を設ける。引き出し側には
空ポケットを含み400mm
以上のシールテープ
部を設ける。
30 pitches(no components)
minimum leaders shall be
provided at the beginning and
the end of each reel.
400mm minimum leaders
including no component
carrier tape shall be provided
at the end of each reel.
MURATA MFG.CO., LTD
Reference Only
8 / 12
Spec No.J(E)TE243C-0106-01
テーピング仕様
TAPING SPECIFICATIONS
5CCEG TYPE
【リール寸法図・REEL DETAILS】
表示
13
φ
φ
φ ±0.8
21
φ
±1.0
+0.3
-0
2
80
±0.2
Marking
±2
330
【荷姿・PACKING CASE】
表示・MARKING
(記事・Note)
1.リールは EIAJ ET-7200 に準拠する。
Reel conform to EIAJ ET-7200.
2.リール材質はプラスチックとする。
Reel material shall be plastic.
3.1リール当たりの数量は、
750個入りとする。
Parts quantity per reel
shall be 750 pieces
(750 pcs. / 1 reel)
4.リールには貴社部品番号、
数量を 表示する。
±0.5
17.5
Each reel shall be
±1.0
21.5
marked with the following ;
Customer’s part number
Quantity
(記事・Note)
1.梱包材の材質は紙とする。
Packing case material shall be kraft paper.
2.梱包箱は1リール入りとする。
Reel quantity per packing case shall be one
(1) reel.
3.梱包箱には貴社部品番号、
数量を 表示する。
Each packing case shall be marked with
the followings ;
Customer’s part number
Quantity
MURATA MFG.CO., LTD
Reference Only
9 / 12
Spec No.J(E)TE243C-0106-01
5CCEG Type 一般仕様 General Specifications
推奨パターン図
Recommended PCB pattern
基板パターンはなるべく下図の推奨パターン寸法をご使用下さい。
Use the PC board pattern as recommended in the following diagram.
3.3
1.9
1.3
1.4
4.7
1.3
1.9
1
3.6
クリームはんだ厚
THICKENS OF CREAM SOLDER : 200μm min.
単位:mm
Unit
リフローはんだ条件(温度プロファイル)
Reflow soldering condition (Temperature Profile)
Temperature
(℃)
250℃ 10sec
(255℃max -0/+5sec)
220
190
160
リフロー可能回数: 2 回 times
Reflow possibility times
(sec)
60~120 sec
30~60 sec
その他はんだ条件
Other soldering conditions.
コテはんだによる修正はリフローはんだ条件に合わせて行って下さい。
特にコテ先の熱容量の過剰にはご注意下さい。(380℃、3 秒、1回)
Apply reflow soldering conditions when using soldering iron and for rework.
Especially be careful not to overheat the tip of the soldering iron.(380℃、3s、1time)
MURATA MFG.CO., LTD
Reference Only
10 / 12
Spec No.J(E)TE243C-0106-01
5CCEG Type 注意事項 Precautions
使用上の注意事項(安全対策) Notice
1, 樹脂コーティング Resin coating
製品を樹脂で外装される場合、樹脂のキュアストレスが強いとインダクタンスが変化したり製品の性能に
影響を及ぼすことがありますので、樹脂の選択には十分ご注意下さい。また、実装された状態での信頼性評
価を実施下さい。
The inductance value may change and / or it may affect on the product's performance due to high
cure-stress of resin to be used for coating / molding products. So please pay your careful attention when you select resin.
In prior to use, please make the reliability evaluation with the product mounted in your application set.
2, フェールセーフ Fail-safe
当製品に万が一異常や不具合が生じた場合でも、二次災害防止のために完成品に適切な
フェールセーフ機能を必ず付加して下さい。
Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that may be
caused by the abnormal function or the failure of our product.
3, 定格上の注意 Caution(Rating)
定格電流を超えてのご使用は避けてください。定格電流を超えて使用しますと、当製品は発熱し、
ワイヤー間のショート、断線あるいははんだが溶けて部品が脱落する恐れがあります。
Do not exceed maximum rated current of the product. Thermal stress may be transmitted to the product and
short / open circuit of the product or falling off the product may be occurred.
4, 温度上昇 Temperature rise
インダクタの温度はご設計環境で大きく変わります。
熱設計には充分ご注意をされ温度保証範囲でのご設計をお願いします。
Temperature rise of power inductor depends on the installation condition in end products.
It shall be confirmed in the actual end product that temperature rise of power inductor is in the limit
specified temperature class.
MURATA MFG.CO., LTD
Reference Only
11 / 12
Spec No.J(E)TE243C-0106-01
5CCEG Type 注意事項 Precautions
使用上の注意事項(安全対策) Notice
5, 保管・運搬 Storage and Handling Requirements
① 保管期間
納入後、6ヶ月以内にご使用下さい。
なお、6ヶ月を超える場合は、はんだ付け性をご確認の上ご使用ください。
② 保管方法
・当製品は、温度-10~+40℃、相対湿度 15~85%で、且つ、急激な温湿度の変化の
ない室内で保管ください。
硫黄・塩素ガス・酸など腐食性ガス雰囲気中で保管されますと、電極が酸化し、はんだ付け性不良が
生じたり、製品の巻線部分が腐食する等の原因となります。
・バルクの状態での保管は避けてください。バルクでの保管は製品同士あるいは製品と他の部品が
衝突し、コアカケや断線を生じることがあります。
・湿気、塵などの影響を避けるため、床への直置は避けパレットなどの上に保管ください。
・直射日光、熱、振動などが加わる場所での保管は避けてください。
③ 運搬
過度の振動、衝撃は製品の信頼性を低下させる原因となりますので、取り扱いには充分注意をお願い
します。
(1) Storage period
Use the products within 6 months after delivered.
Solderability should be checked if this period is exceeded.
(2) Storage conditions
• Products should be stored in the warehouse on the following conditions.
Temperature : -10 ~ 40°C
Humidity : 15 to 85% relative humidity, No rapid change on temperature and humidity
chlorine gas or acid, or it may cause oxidization of electrode, resulting in poor solderability.
• Products should not be stored on bulk packaging condition to prevent the chipping of the core and the
breaking of winding wire caused by the collision between the products.
• Products should be stored on the palette for the prevention of the influence from humidity, dust and so on.
• Products should be stored in the warehouse without heat shock, vibration, direct sunlight and so on.
(3) Handling condition
Care should be taken when transporting or handling product to avoid excessive vibration or mechanical shock.
MURATA MFG.CO., LTD
Reference Only
12 / 12
Spec
Spec No.J(E)TE243C-0048D-01
No.J(E)TE243C-0106-01
5CCEG Type
お願い Note
適用範囲 Scope
この製品は、パワートレインやセーフティを除く車載用電子機器に使用される製品です。
This product applies to automotive Electronics except for Power train and Safety.
注意 Caution
1, 用途の限定 Limitation of Applications
当製品について、その故障や誤動作が人命または財産に危害を及ぼす恐れがある等の理由により、
高信頼性が要求される以下の用途でのご使用をご検討の場合は、必ず事前に当社までご連絡下さい。
①航空機器 ②宇宙機器 ③海底機器 ④発電所制御機器
⑤医療機器 ⑥防災/防犯機器 ⑦交通用信号機器 ⑧輸送機器(車・列車・船舶等)
⑨その他上記機器と同等の機器 ⑩サーバー
Please contact us before using our products for the applications listed below which require especially high reliability
for the prevention of defects which might directly cause damage to the third party's life, body or property.
(1) Aircraft equipment (2) Aerospace equipment (3) Undersea equipment (4) Power plant control equipment
(5) Medical equipment to the applications listed in the above (6)Disaster prevention / crime prevention equipment
(7) Traffic signal equipment (8) Transportation equipment (vehicles, trains, ships, etc.)
(9) Applications of similar complexity and /or reliability requirements(10)Data-processing equipment
お願い
(1)ご使用に際しては、貴社製品に実装された状態で必ず評価して下さい。
(2)当製品を当参考図の記載内容を逸脱して使用しないで下さい。
(3)当参考図の内容は予告なく変更することがございます。ご注文の前に、納入仕様書の内容をご確認いただくか
承認図の取り交わしをお願いします。
Note
(1) Please make sure that your product has been evaluated in view of your specifications with our product being
mounted to your product.
(2) You are requested not to use our product deviating from the reference specifications.
(3) The contents of this reference specification are subject to change without advance notice.
Please approve our product specifications or transact the approval sheet for product specifications before ordering.
MURATA MFG.CO., LTD