515CBA4M09600AAGR

Si 515 V O LTA G E -C ONTROLLED C RYSTAL O SCILLATOR ( VC X O) 100 kH Z TO 25 0 M H Z Features        Supports any frequency from  100 kHz to 250 MHz Low-jitter operation  Short lead times: 6 digit resolution Figure 2. Part Number Convention Example ordering part number: 515BBB212M500BAGR. The series prefix, 515, indicates the device is a single frequency VCXO. The 1st option code B specifies the output format is LVDS and powered from a 3.3 V supply. The stability and APR code B indicates a temperature stability of ±20 ppm with a tuning slope of ±120 ppm/V. The 3rd option code B specifies the OE pin is active low. The frequency code is 212M500. Per this convention, and as indicated by the part number lookup utility at www.skyworksinc.com/en/application-pages/timing-lookup-customize, the output frequency is 212.5 MHz. The package code B refers to the 3.2 x 5 mm footprint with six pins. The last A refers to the product revision, G indicates the temperature range (–40 to +85 °C), and R specifies the device ships in tape and reel format. Note: CMOS and Dual CMOS maximum frequency is 212.5 MHz. 14 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.2 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • August 12, 2021 Si515 5. Package Outline Diagram: 5 x 7 mm, 6-pin Figure 3 illustrates the package details for the Si515. Table 14 lists the values for the dimensions shown in the illustration. Figure 3. Si515 Outline Diagram Table 14. Package Diagram Dimensions (mm) Dimension A b c D D1 e E E1 H L L1 p R aaa bbb ccc ddd eee Min 1.50 1.30 0.50 4.30 6.10 0.55 1.17 0.05 1.80 Nom 1.65 1.40 0.60 5.00 BSC. 4.40 2.54 BSC. 7.00 BSC. 6.20 0.65 1.27 0.10 — 0.7 REF. 0.15 0.15 0.10 0.10 0.05 Max 1.80 1.50 0.70 4.50 6.30 0.75 1.37 0.15 2.60 Notes: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing per ANSI Y14.5M-1994. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 15 Rev. 1.2 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • August 12, 2021 Si 515 6. PCB Land Pattern: 5 x 7 mm, 6-pin Figure 4 illustrates the 5 x 7 mm PCB land pattern for the Si515. Table 15 lists the values for the dimensions shown in the illustration. Figure 4. Si515 PCB Land Pattern Table 15. PCB Land Pattern Dimensions (mm) Dimension C1 E X1 Y1 (mm) 4.20 5.08 1.55 1.95 Notes: General 1. 2. 3. 4. All dimensions shown are in millimeters (mm) unless otherwise noted. Dimensioning and Tolerancing is per the ANSI Y14.5M-1994 specification. This Land Pattern Design is based on the IPC-7351 guidelines. All dimensions shown are at Maximum Material Condition (MMC). Least Material Condition (LMC) is calculated based on a Fabrication Allowance of 0.05 mm. Solder Mask Design 5. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad is to be 60 µm minimum, all the way around the pad. Stencil Design 6. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure good solder paste release. 7. The stencil thickness should be 0.125 mm (5 mils). 8. The ratio of stencil aperture to land pad size should be 1:1. Card Assembly 9. A No-Clean, Type-3 solder paste is recommended. 10. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. 16 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.2 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • August 12, 2021 Si515 7. Package Outline Diagram: 3.2 x 5.0 mm, 6-pin Figure 5 illustrates the package details for the 3.2 x 5 mm Si515. Table 16 lists the values for the dimensions shown in the illustration. Figure 5. Si515 Outline Diagram Table 16. Package Diagram Dimensions (mm) Dimension A b c D D1 e E E1 H L L1 p R aaa bbb ccc ddd eee Min 1.06 0.54 0.35 2.55 4.35 0.45 0.80 0.05 1.17 Nom 1.17 0.64 0.45 3.20 BSC 2.60 1.27 BSC 5.00 BSC 4.40 0.55 0.90 0.10 1.27 0.32 REF 0.15 0.15 0.10 0.10 0.05 Max 1.33 0.74 0.55 2.65 4.45 0.65 1.00 0.15 1.37 Notes: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing per ANSI Y14.5M-1994. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 17 Rev. 1.2 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • August 12, 2021 Si 515 8. PCB Land Pattern: 3.2 x 5.0 mm, 6-pin Figure 6 illustrates the recommended 3.2 x 5 mm PCB land pattern for the Si515. Table 17 lists the values for the dimensions shown in the illustration.   Figure 6. Si515 PCB Land Pattern Table 17. PCB Land Pattern Dimensions (mm) Dimension (mm) C1 2.60 E 1.27 X1 0.80 Y1 1.70 Notes: General 1. 2. 3. 4. All dimensions shown are in millimeters (mm) unless otherwise noted. Dimensioning and Tolerancing is per the ANSI Y14.5M-1994 specification. This Land Pattern Design is based on the IPC-7351 guidelines. All dimensions shown are at Maximum Material Condition (MMC). Least Material Condition (LMC) is calculated based on a Fabrication Allowance of 0.05 mm. Solder Mask Design 5. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad is to be 60 µm minimum, all the way around the pad. Stencil Design 6. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure good solder paste release. 7. The stencil thickness should be 0.125 mm (5 mils). 8. The ratio of stencil aperture to land pad size should be 1:1. Card Assembly 9. A No-Clean, Type-3 solder paste is recommended. 10. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. 18 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.2 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • August 12, 2021 Si515 9. Package Outline Diagram: 2.5 x 3.2 mm, 6-pin Figure 7 illustrates the package details for the 2.5 x 3.2 mm Si515. Table 18 lists the values for the dimensions shown in the illustration. Figure 7. Si515 Outline Diagram Table 18. Package Diagram Dimensions (mm) Dimension A Min — Nom — Max 1.1 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 19 Rev. 1.2 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • August 12, 2021 Si 515 Table 18. Package Diagram Dimensions (mm) (Continued) A1 A2 W D e E M L D1 E1 SE aaa bbb ddd 0.26 REF 0.7 REF 0.65 0.45 0.7 3.20 BSC 1.25 BSC 2.50 BSC 0.30 BSC 0.5 2.5 BSC 1.65 BSC 0.825 BSC 0.1 0.2 0.08 0.75 0.55 Notes: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing per ANSI Y14.5M-1994. 20 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.2 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • August 12, 2021 Si515 10. PCB Land Pattern: 2.5 x 3.2 mm, 6-pin Figure 8 illustrates the 2.5 x 3.2 mm PCB land pattern for the Si515. Table 19 lists the values for the dimensions shown in the illustration. Figure 8. Si515 Recommended PCB Land Pattern Table 19. PCB Land Pattern Dimensions (mm) Dimension C1 (mm) 1.9 E 2.50 X1 0.70 Y1 1.05 Notes: General 3. All dimensions shown are at Maximum Material Condition (MMC). Least Material Condition (LMC) is calculated based on a Fabrication Allowance of 0.05 mm. 4. This Land Pattern Design is based on the IPC-7351 guidelines. Solder Mask Design 5. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad is to be 60 µm minimum, all the way around the pad. Stencil Design 6. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure good solder paste release. 7. The stencil thickness should be 0.125 mm (5 mils). 8. The ratio of stencil aperture to land pad size should be 1:1 for all perimeter pins. Card Assembly 9. A No-Clean, Type-3 solder paste is recommended. 10. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 21 Rev. 1.2 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • August 12, 2021 Si 515 11. Top Marking Use the part number configuration utility: www.skyworksinc.com/en/application-pages/timing-lookup-customize to cross-reference the mark code to a specific device configuration. 11.1. Si515 Top Marking 5 C CC CC T TTT TT Y Y WW 11.2. Top Marking Explanation Mark Method: Laser Line 1 Marking: 5 = Si515 CCCCC = Mark Code 5CCCCC Line 2 Marking: TTTTTT = Assembly Manufacturing Code TTTTTT Line 3 Marking: Pin 1 indicator. Circle with 0.5 mm diameter; left-justified YY = Year. WW = Work week. Characters correspond to the year and work week of package assembly. YYWW 22 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.2 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • August 12, 2021 Si515 REVISION HISTORY Revision 1.2 June, 2018  Changed “Trays” to “Coil Tape” in Ordering Guide. Revision 1.1 December, 2017  Added 2.5 x 3.2 mm package. Revision 1.0  Updated Table 1 on page 3. Updates to supply current typical and maximum values for CMOS, LVDS, LVPECL and HCSL. frequency test condition corrected to 100 MHz. Updates to OE VIH minimum and VIL maximum values. CMOS  Updated Table 3 on page 4. Dual CMOS nominal frequency maximum added. time maximum values updated. Enable time parameter added. Disable  Updated Table 4 on page 5. CMOS output rise / fall time typical and maximum values updated. output rise / fall time maximum value updated. LVPECL output swing maximum value updated. LVDS output common mode typical and maximum values updated. HCSL output swing maximum value updated. Duty cycle minimum and maximum values tightened to 48/52%. LVPECL/HCSL  Updated Table 5 on page 6. Phase jitter test condition, typical and maximum value updated. noise typical values updated. Additive RMS jitter due to external power supply noise typical values updated. Phase     Added Tables 6, 7, 8 for LVDS, HCSL, CMOS and Dual CMOS operations. Added note to Figure 2 clarifying CMOS and Dual CMOS maximum frequency. Updated Figure 5 outline diagram to correct pinout. Updated “11. Top Marking” section and moved to page 22. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 23 Rev. 1.2 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • August 12, 2021