Reference Only
Spec. No. JENF243A-9148B-01
P.1/8
Chip Ferrite Bead BLM31KN□□□SH1L
Murata Standard Reference Specification [AEC-Q200]
1. Scope
This reference specification applies to Chip Ferrite Bead for Automotive Electronics BLM31KN_SH Series based on AEC-Q200.
2. Part Numbering
(ex.)
BL
M
31
(1)
(2)
(3)
(1)Product ID
(2)Type
(3)Dimension (L×W)
KN
121
S
H
1
L
(4)
(5)
(6) (7)
(8)
(9)
(4)Characteristics
(5)Typical Impedance at 100MHz
(6)Performance
(7)Category (for Automotive Electronics)
(8)Numbers of Circuit
(9)Packaging (L:Taping)
3. Rating
Customer
Part Number
Rated
Current
(mA)
(Note1)
at 85°C at 125°C
DC Resistance
(Ω max.)
Values
Initial
After
Values
Testing
0.009
0.011
0.016
0.019
MURATA
Part Number
Impedance (Ω)
(at 100MHz, Under Standard
Testing Condition)
BLM31KN121SH1L
BLM31KN271SH1L
120±25%
270±25%
6000
4500
4000
3000
BLM31KN471SH1L
470±25%
4000
2700
0.02
0.024
BLM31KN601SH1L
600±25%
2900
2000
0.038
0.045
800±25%
2500
1700
0.05
0.06
1000±25%
2000
1400
• Storage Temperature: -55°C to +125°C
0.075
0.09
BLM31KN801SH1L
BLM31KN102SH1L
• Operating Temperature: -55°C to +125°C
ESD Rank
6:25kV
6
Standard Testing Conditions
(Note1) Rated Current is derated as right figure
depending on the operating temperature.
< In case of doubt >
Temperature : 20°C±2 °C
Humidity : 60%(RH) to 70%(RH)
Atmospheric pressure : 86kPa to 106kPa
R a te d C u r re n t ( A )
< Unless otherwise specified >
Temperature : Ordinary Temp. (15 °C to 35 °C )
Humidity : Ordinary Humidity (25%(RH) to 85%(RH))
85℃x
Describe the Rated current as x[A]
in case of more than 1A.
1
125℃
0
85
4. Style and Dimensions
Operating Temperature (°C)
1.6±0.2
1.6±0.2
1.1±0.2
3.2±0.2
125
0.7±0.3
■ Equivalent Circuit
(
: Electrode
(in mm)
■ Unit Mass (Typical value)
0.041 g
5.Marking
No marking.
MURATA MFG.CO., LTD.
)
Resistance element becomes
dominant at high frequencies.
Reference Only
Spec. No. JENF243A-9148B-01
P.2/8
6. Specifications
6-1. Electrical
No.
Item
6-1-1 Impedance
Specification
Meet item 3.
6-1-2 DC Resistance
Meet item 3.
Test Method
Measuring Frequency : 100MHz±1MHz
Measuring Equipment : KEYSIGHT4291A or the equivalent
Test Fixture : KEYSIGHT16192A or the equivalent
Measuring Equipment : Digital multi meter
*Except resistance of the Substrate and Wire
6-2. Mechanical Performance (based on Table 13 for FILTER EMI SUPPRESSORS/ FILTERS)
AEC-Q200 Rev.D issued June. 1 2010
AEC-Q200
Murata Specification / Deviation
No.
Stress
Test Method
3 High
1000hours at 125 deg C
Meet Table A after testing.
Temperature
Set for 24hours at room temperature, then
Table A
Exposure
measured.
Appearance
No damage
Impedance
Change
Within ±50%
(at 100MHz)
DC
Meet item 3.
Resistance
4 Temperature Cycling
1000cycles
Meet Table A after testing.
-55 deg C to +125 deg C
Set for 24hours at room temperature, then
measured.
5 Destructive
Physical Analysis
Per EIA469
No electrical tests
No defects
7 Biased Humidity
1000hours at 85 deg C, 85%RH
Apply max rated current.
Apply 125 deg C 1000hours
Set for 24hours at room temperature, then
measured
Visual inspection
Meet Table A after testing.
8 Operational Life
9 External Visual
10 Physical Dimension
Meet Table A after testing.
If the rated current of parts exceed 1A,
the operating temperature should be 85 deg C.
No abnormalities
Meet ITEM 4
(Style and Dimensions)
12 Resistance to Solvents Per MIL-STD-202 Method 215
No defects
13 Mechanical Shock
Meet Table B after testing.
Table B
14 Vibration
Per MIL-STD-202 Method 213
Condition F:
1500g’s(14.7N)/0.5ms/
Half sine
5g's(0.049N) for 20 minutes, 12cycles
each of
3 orientations
Test from 10-2000Hz.
Not Applicable
Appearance
Impedance
Change
(at 100MHz)
DC
Resistance
No damage
Within ±30%
Meet item 3.
Meet Table B after testing.
MURATA MFG.CO., LTD.
Reference Only
Spec. No. JENF243A-9148B-01
P.3/8
AEC-Q200
No.
Stress
15 Resistance
to Soldering Heat
Murata Specification / Deviation
Test Method
Solder temperature
260C+/-5 deg C
Immersion time 10s
Reflow soldering method:
Solder : Sn-3.0Ag-0.5Cu
Pre-Heating : 150°C-180°C, 90±30s
Heating
: above 220°C, 60±30s
Peak temperature: 260°C
Cycle of reflow: 2times
Then measured after exposure in the room
condition for 48h±4h.
17 ESD
Per AEC-Q200-002
18 Solderability
Per J-STD-002
19 Electrical
Characterization
20 Flammability
21 Board Flex
Measured : Impedance
22 Terminal Strength
30 Electrical
Transient
Conduction
Meet Table A after testing.
Meet Table A after testing.
ESD Rank: Refer to Item 3. Rating
Method b : Not Applicable
95% of the terminations is to be soldered.
No defects
Per UL-94
Epoxy-PCB(1.6mm)
Deflection 2mm(min)
60s minimum holding time
Per AEC-Q200-006
Not Applicable
Meet Table B after testing.
Per ISO-7637-2
Not Applicable
No defects
-0
3.5±0.1
1.9±0.1
+0.3
φ 1.0- 0
1.75±0.1
1.3±0.1
0.2±0.1
8.0±0.3
φ 1.5+0.1
3.5±0.05
2.0±0.05
4.0±0.1
4.0±0.1
1.75±0.1
7. Specification of Packaging
7-1. Appearance and Dimensions (8mm-wide plastic tape)
Direction of feed
(in mm)
*Dimension of the Cavity is measured at the bottom side.
(1) Taping
Products shall be packaged in the each embossed cavity of 8mm-wide, 4mm-pitch and plastic tape
continuously and sealed by cover tape.
(2) Sprocket hole : Sprocket hole shall be located on the left hand side toward the direction of feed.
(3) Spliced point : The cover tape has no spliced point.
(4) Missing components number
Missing components number within 0.025% of the number per reel or 1 pc., whichever is greater,
and are not continuous. The specified quantity per reel is kept.
MURATA MFG.CO., LTD.
Reference Only
Spec. No. JENF243A-9148B-01
P.4/8
7-2. Tape Strength
(1) Pull Strength
Plastic tape
Cover tape
5N min.
10N min.
165 to 180 degree
(2) Peeling off force of Cover tape
0.2N to 0.7N (Minimum value is typical.)
*Speed of Peeling off:300mm/min
F
Cover tape
Plastic tape
7-3. Taping Condition
(1) Standard quantity per reel
Quantity per 180mm reel : 2500 pcs. / reel
(2) There shall be leader-tape (cover tape only and empty tape ) and trailer- tape (empty tape) as follows.
(3) Marking for reel
The following items shall be marked on a label and the label is stuck on the reel.
(Customer part number, MURATA part number, Inspection number (∗1), RoHS marking (∗2), Quantity, etc)
∗1) « Expression of Inspection No. »
□□ OOOO ×××
(1)
(1) Factory Code
(2) Date
(2)
(3)
First digit
: Year / Last digit of year
Second digit
: Month / Jan. to Sep. → 1 to 9, Oct. to Dec. → O, N, D
Third, Fourth digit : Day
(3) Serial No.
∗2) « Expression of RoHS marking »
ROHS – Y (△)
(1) (2)
(1) RoHS regulation conformity parts.
(2) MURATA classification number
(4) Outside package
These reels shall be packed in the corrugated cardboard package and the following items shall be marked
on a label and the label is stuck on the box.
(Customer name, Purchasing order number, Customer part number, MURATA part number,
RoHS marking (∗2), Quantity, etc)
(5) Dimensions of reel and taping (leader-tape, trailer-tape)
7-4. Specification of Outer Case
Label
H
D
W
Outer Case Dimensions
Standard Reel Quantity in Outer Case
(mm)
(Reel)
W
D
H
186
186
93
5
∗ Above Outer Case size is typical. It depends on a quantity of an order.
MURATA MFG.CO., LTD.
Reference Only
Spec. No. JENF243A-9148B-01
P.5/8
8. ! Caution
8-1. Rating
Do not use products beyond the Operating Temperature Range and Rated Current.
8-2. Surge current
Excessive surge current (pulse current or rush current) than specified rated current applied to the product may cause a
critical failure, such as an open circuit, burnout caused by excessive temperature rise.
Please contact us in advance in case of applying the surge current.
8-3. Fail Safe
Be sure to provide an appropriate fail-safe function on your product to prevent from a second damage
that may be caused by the abnormal function or the failure of our products.
8-4. Limitation of Applications
Please contact us before using our products for the applications listed below which require especially high
reliability for the prevention of defects which might directly cause damage to the third party's life, body or property.
(1)Aircraft equipment
(6)Disaster prevention / crime prevention equipment
(2)Aerospace equipment
(7)Traffic signal equipment
(3)Undersea equipment
(8)Transportation equipment (trains, ships, etc.)
(4)Power plant control equipment
(9) Data-processing equipment
(5)Medical equipment
(10) Applications of similar complexity and /or reliability requirements
to the applications listed in the above
9. Notice
This product is designed for solder mounting.
Please consult us in advance for applying other mounting method such as conductive adhesive.
9-1. Land pattern designing
• Standard land dimensions (Reflow soldering)
Rated
Current
(A)
Chip Ferrite Bead
c
d
2
2.5~2.9
4~6
Land pad thickness and
dimension d
18µm
1.8
2.4
6.4
35µm
1.8
1.8
3.3
70µm
1.8
1.8
1.8
(in mm)
*The excessive heat by land pads may cause
deterioration at joint of products with substrate.
a
b
Solder Resist
Pattern
Type
BLM31KN
MURATA MFG.CO., LTD.
Soldering
Reflow
a
2.0
b
4.3
c
1.8
Reference Only
Spec. No. JENF243A-9148B-01
P.6/8
9-2. Soldering Conditions
Products can be applied to reflow soldering.
(1) Flux,Solder
Flux
Use rosin-based flux, but not highly acidic flux (with chlorine content exceeding 0.2(wt)%. )
Do not use water-soluble flux.
Solder
Use Sn-3.0Ag-0.5Cu solder
Standard thickness of solder paste : 100 µm to 200 μm
(2) Soldering conditions
• Pre-heating should be in such a way that the temperature difference between solder and ferrite surface is limited
to 150℃ max. Also cooling into solvent after soldering should be in such a way that the temperature difference
is limited to 100℃ max.
Insufficient pre-heating may cause cracks on the ferrite, resulting in the deterioration of product quality.
• Standard soldering profile and the limit soldering profile is as follows.
The excessive limit soldering conditions may cause leaching of the electrode and / or resulting
in the deterioration of product quality.
(3) Soldering profile
□Reflow soldering profile
Temp.
(℃)
260℃
245℃±3℃
220℃
230℃
Limit Profile
180
150
Standard Profile
30s~60s
60s max.
90s±30s
Pre-heating
Heating
Peak temperature
Cycle of reflow
Standard Profile
150~180°C 、90s±30s
above 220°C、30s~60s
245±3°C
2 times
Time. (s)
Limit Profile
above 230°C、60s max.
260°C, 10s
2 times
9-3. Reworking with soldering iron
• Pre-heating: 150°C, 1 min
• Tip temperature: 350°C max.
• Soldering time : 3 (+1, -0) seconds.
• Soldering iron output: 80W max.
• Tip diameter: φ3mm max.
• Times : 2times max.
Note: Do not directly touch the products with the tip of the soldering iron in order to prevent the crack
on the ferrite material due to the thermal shock.
9-4. Solder Volume
Solder shall be used not to be exceed as shown below.
Upper Limit
Recommendable
t
1/3T≦t≦T
(T: Chip thickness)
Accordingly increasing the solder volume, the mechanical stress to product is also increased.
Exceeding solder volume may cause the failure of mechanical or electrical performance.
MURATA MFG.CO., LTD.
Reference Only
Spec. No. JENF243A-9148B-01
P.7/8
9-5. Attention regarding P.C.B. bending
The following shall be considered when designing and laying out P.C.B.'s.
(1) P.C.B. shall be designed so that products are not subject to the mechanical stress for board warpage.
a
Products shall be located in the sideways
direction (Length: a D *1
A > B
A > C
C
B
D
A
Slit
*1 A > D is valid when stress is added vertically to the perforation as with Hand Separation.
If a Cutting Disc is used, stress will be diagonal to the PCB, therefore A > D is invalid.
(3) Mounting Components Near Screw Holes
When a component is mounted near a screw hole, it may be affected by the board deflection that occurs during
the tightening of the screw. Mount the component in a position as far away from the screw holes as possible.
Screw Hole
Recommended
9-6. Mounting density
Add special attention to radiating heat of products when mounting the inductor near the products with heating.
The excessive heat by other products may cause deterioration at joint of this product with substrate.
9-7. Operating Environment
Do not use this product under the following environmental conditions, on deterioration of the Insulation
Resistance of the Ferrite material and/or corrosion of Inner Electrode may result from the use.
(1) in the corrodible atmosphere such as acidic gases, alkaline gases, chlorine, sulfur gases, organic gases and etc
(the sea breeze, Cl2, H2S, NH3, SO2, NO2,etc)
(2) in the atmosphere where liquid such as organic solvent, may splash on the products.
(3) in the atmosphere where the temperature / humidity changes rapidly and it is easy to dew.
MURATA MFG.CO., LTD.
Reference Only
Spec. No. JENF243A-9148B-01
P.8/8
9-8. Resin coating
The impedance value may change and/or it may affect on the product's performance due to high cure-stress of
resin to be used for coating / molding products. So please pay your careful attention when you select resin. In prior to
use, please make the reliability evaluation with the product mounted in your application set.
9-9. Cleaning
Excessive ultrasonic oscillation during cleaning can cause the PCBs to resonate, resulting in cracked chips or broken
solder joints. Before starting your production process, test your cleaning equipment / process to insure it does not
degrade this product.
9-10. Handling of a substrate
After mounting products on a substrate, do not apply any stress to the product caused by bending or twisting to the
substrate when cropping the substrate, inserting and removing a connector from the substrate or tightening screw to
the substrate.
Excessive mechanical stress may cause cracking in the product.
Bending
Twisting
9-11. Storage Conditions
(1) Storage period
Use the products within 6 months after delivered.
Solderability should be checked if this period is exceeded.
(2) Storage conditions
• Products should be stored in the warehouse on the following conditions.
Temperature : -10°C to 40°C
Humidity
: 15% to 85% relative humidity
No rapid change on temperature and humidity
• Don't keep products in corrosive gases such as sulfur, chlorine gas or acid, or it may cause oxidization
of electrode, resulting in poor solderability.
• Products should be stored on the palette for the prevention of the influence from humidity, dust and so on.
• Products should be stored in the warehouse without heat shock, vibration, direct sunlight and so on.
• Avoid storing the product by itself bare (i.e.exposed directly to air).
(3) Delivery
Care should be taken when transporting or handling product to avoid excessive vibration or mechanical shock.
10 .
! Note
(1)Please make sure that your product has been evaluated in view of your specifications with our product being
mounted to your product.
(2)You are requested not to use our product deviating from the agreed specifications.
(3)The contents of this reference specification are subject to change without advance notice. Please approve our
product specifications or transact the approval sheet for product specifications before ordering.
MURATA MFG.CO., LTD.