C8051F55x/56x/57x
Mixed Signal ISP Flash MCU Family
Analog Peripherals
- 12-Bit ADC
•
•
•
•
•
-
Memory
- 2304 bytes internal data RAM (256 + 2048 XRAM)
- 32 or 16 kB Flash; In-system programmable in
Up to 200 ksps
Up to 32 external single-ended inputs
VREF from on-chip VREF, external pin or VDD
Internal or external start of conversion source
Built-in temperature sensor
512-byte Sectors
Digital Peripherals
- 33, 25, or 18 Port I/O; All 5 V tolerant
- CAN 2.0 Controller—no crystal required
- LIN 2.1 Controller (Master and Slave capable); no
Two Comparators
•
•
•
Programmable hysteresis and response time
Configurable as interrupt or reset source
Low current
On-Chip Debug
- On-chip debug circuitry facilitates full speed, non-
-
intrusive in-system debug (no emulator required)
Provides breakpoints, single stepping,
inspect/modify memory and registers
Superior performance to emulation systems using
ICE-chips, target pods, and sockets
Low cost, complete development kit
-
-
Supply Voltage 1.8 to 5.25 V
- Typical operating current: 19 mA at 50 MHz
- Typical stop mode current: 1 µA
High-Speed 8051 µC Core
- Pipelined instruction architecture; executes 70% of
-
ANALOG
PERIPHERALS
12-bit
200 ksps
ADC
Clock Sources
- Internal 24 MHz with ±0.5% accuracy for CAN and
-
master LIN operation
External oscillator: Crystal, RC, C, or clock
(1 or 2 pin modes)
Can switch between clock sources on-the-fly;
useful in power saving modes
Packages
- 40-pin QFN (C8051F568-9 and ‘F570-5)
- 32-pin QFP/QFN (C8051F560-7)
- 24-pin QFN (C8051F550-7)
Automotive Qualified
- Temperature Range: –40 to +125 °C
- Compliant to AEC-Q100
instructions in 1 or 2 system clocks
Up to 50 MIPS throughput with 50 MHz clock
Expanded interrupt handler
A
M
U
X
crystal required
Hardware enhanced UART, SMBus™, and
enhanced SPI™ serial ports
Four general purpose 16-bit counter/timers
16-bit programmable counter array (PCA) with six
capture/compare modules and enhanced PWM
functionality
TEMP
SENSOR
VREG
Voltage
Comparators 0-1 VREF
24 MHz PRECISION
INTERNAL OSCILLATOR
DIGITAL I/O
UART 0
SMBus
SPI
PCA
Timers 0-3
CAN
LIN
Ports 0-4
Crossbar
External
Memory
Interface
2x Clock Multiplier
HIGH-SPEED CONTROLLER CORE
32 kB
ISP FLASH
FLEXIBLE
INTERRUPTS
Rev. 1.2 9/14
8051 CPU
(50 MIPS)
DEBUG
CIRCUITRY
2 kB XRAM
POR
Copyright © 2014 by Silicon Laboratories
WDT
C8051F55x, C8051F56x, C8051F57x
C8051F55x/56x/57x
2
Rev. 1.2
C8051F55x/56x/57x
Table of Contents
1. System Overview ..................................................................................................... 16
2. Ordering Information ............................................................................................... 20
3. Pin Definitions.......................................................................................................... 22
4. Package Specifications ........................................................................................... 28
4.1. QFN-40 Package Specifications........................................................................ 28
4.2. QFP-32 Package Specifications........................................................................ 30
4.3. QFN-32 Package Specifications........................................................................ 32
4.4. QFN-24 Package Specifications........................................................................ 34
5. Electrical Characteristics ........................................................................................ 36
5.1. Absolute Maximum Specifications..................................................................... 36
5.2. Electrical Characteristics ................................................................................... 37
6. 12-Bit ADC (ADC0) ................................................................................................... 47
6.1. Modes of Operation ........................................................................................... 48
6.1.1. Starting a Conversion................................................................................ 48
6.1.2. Tracking Modes......................................................................................... 48
6.1.3. Timing ....................................................................................................... 49
6.1.4. Burst Mode................................................................................................ 50
6.2. Output Code Formatting .................................................................................... 52
6.2.1. Settling Time Requirements...................................................................... 52
6.3. Selectable Gain ................................................................................................. 53
6.3.1. Calculating the Gain Value........................................................................ 53
6.3.2. Setting the Gain Value .............................................................................. 55
6.4. Programmable Window Detector....................................................................... 61
6.4.1. Window Detector In Single-Ended Mode .................................................. 63
6.5. ADC0 Analog Multiplexer .................................................................................. 65
6.6. Temperature Sensor.......................................................................................... 67
7. Voltage Reference.................................................................................................... 68
8. Comparators............................................................................................................. 70
8.1. Comparator Multiplexer ..................................................................................... 76
9. Voltage Regulator (REG0) ....................................................................................... 79
10. CIP-51 Microcontroller........................................................................................... 81
10.1. Performance .................................................................................................... 81
10.2. Instruction Set.................................................................................................. 83
10.2.1. Instruction and CPU Timing .................................................................... 83
10.3. CIP-51 Register Descriptions .......................................................................... 87
10.4. Serial Number Special Function Registers (SFRs) ......................................... 91
11. Memory Organization ............................................................................................ 92
11.1. Program Memory............................................................................................. 92
11.1.1. MOVX Instruction and Program Memory ................................................ 93
11.2. Data Memory ................................................................................................... 93
11.2.1. Internal RAM ........................................................................................... 93
12. Special Function Registers................................................................................... 95
12.1. SFR Paging ..................................................................................................... 95
Rev. 1.2
3
C8051F55x/56x/57x
12.2. Interrupts and SFR Paging .............................................................................. 95
12.3. SFR Page Stack Example ............................................................................... 97
13. Interrupts .............................................................................................................. 112
13.1. MCU Interrupt Sources and Vectors.............................................................. 112
13.1.1. Interrupt Priorities.................................................................................. 113
13.1.2. Interrupt Latency ................................................................................... 113
13.2. Interrupt Register Descriptions ...................................................................... 115
13.3. External Interrupts INT0 and INT1................................................................. 122
14. Flash Memory....................................................................................................... 124
14.1. Programming The Flash Memory .................................................................. 124
14.1.1. Flash Lock and Key Functions .............................................................. 124
14.1.2. Flash Erase Procedure ......................................................................... 125
14.1.3. Flash Write Procedure .......................................................................... 125
14.1.4. Flash Write Optimization ....................................................................... 126
14.2. Non-volatile Data Storage ............................................................................. 127
14.3. Security Options ............................................................................................ 127
14.4. Flash Write and Erase Guidelines ................................................................. 129
14.4.1. VDD Maintenance and the VDD monitor ................................................ 129
14.4.2. PSWE Maintenance .............................................................................. 130
14.4.3. System Clock ........................................................................................ 130
15. Power Management Modes................................................................................. 135
15.1. Idle Mode....................................................................................................... 135
15.2. Stop Mode ..................................................................................................... 136
15.3. Suspend Mode .............................................................................................. 136
16. Reset Sources ...................................................................................................... 138
16.1. Power-On Reset ............................................................................................ 139
16.2. Power-Fail Reset/VDD Monitor ..................................................................... 139
16.3. External Reset ............................................................................................... 141
16.4. Missing Clock Detector Reset ....................................................................... 141
16.5. Comparator0 Reset ....................................................................................... 142
16.6. PCA Watchdog Timer Reset ......................................................................... 142
16.7. Flash Error Reset .......................................................................................... 142
16.8. Software Reset .............................................................................................. 142
17. External Data Memory Interface and On-Chip XRAM ....................................... 144
17.1. Accessing XRAM........................................................................................... 144
17.1.1. 16-Bit MOVX Example .......................................................................... 144
17.1.2. 8-Bit MOVX Example ............................................................................ 144
17.2. Configuring the External Memory Interface ................................................... 145
17.3. Port Configuration.......................................................................................... 145
17.4. Multiplexed Mode .......................................................................................... 149
17.5. Memory Mode Selection................................................................................ 150
17.5.1. Internal XRAM Only .............................................................................. 150
17.5.2. Split Mode without Bank Select............................................................. 150
17.5.3. Split Mode with Bank Select.................................................................. 151
17.5.4. External Only......................................................................................... 151
4
Rev. 1.2
C8051F55x/56x/57x
17.6. Timing .......................................................................................................... 151
17.6.1. Multiplexed Mode .................................................................................. 153
18. Oscillators and Clock Selection ......................................................................... 157
18.1. System Clock Selection................................................................................. 157
18.2. Programmable Internal Oscillator .................................................................. 159
18.2.1. Internal Oscillator Suspend Mode ......................................................... 159
18.3. Clock Multiplier .............................................................................................. 162
18.4. External Oscillator Drive Circuit..................................................................... 164
18.4.1. External Crystal Example...................................................................... 166
18.4.2. External RC Example............................................................................ 167
18.4.3. External Capacitor Example.................................................................. 167
19. Port Input/Output ................................................................................................. 169
19.1. Port I/O Modes of Operation.......................................................................... 170
19.1.1. Port Pins Configured for Analog I/O...................................................... 170
19.1.2. Port Pins Configured For Digital I/O...................................................... 170
19.1.3. Interfacing Port I/O in a Multi-Voltage System ...................................... 171
19.2. Assigning Port I/O Pins to Analog and Digital Functions............................... 171
19.2.1. Assigning Port I/O Pins to Analog Functions ........................................ 171
19.2.2. Assigning Port I/O Pins to Digital Functions.......................................... 171
19.2.3. Assigning Port I/O Pins to External Digital Event Capture Functions ... 172
19.3. Priority Crossbar Decoder ............................................................................. 172
19.4. Port I/O Initialization ...................................................................................... 174
19.5. Port Match ..................................................................................................... 179
19.6. Special Function Registers for Accessing and Configuring Port I/O ............. 183
20. Local Interconnect Network (LIN0)..................................................................... 193
20.1. Software Interface with the LIN Controller..................................................... 194
20.2. LIN Interface Setup and Operation................................................................ 194
20.2.1. Mode Definition ..................................................................................... 194
20.2.2. Baud Rate Options: Manual or Autobaud ............................................. 194
20.2.3. Baud Rate Calculations: Manual Mode................................................. 194
20.2.4. Baud Rate Calculations—Automatic Mode ........................................... 196
20.3. LIN Master Mode Operation .......................................................................... 197
20.4. LIN Slave Mode Operation ............................................................................ 198
20.5. Sleep Mode and Wake-Up ............................................................................ 199
20.6. Error Detection and Handling ........................................................................ 199
20.7. LIN Registers................................................................................................. 200
20.7.1. LIN Direct Access SFR Registers Definitions ....................................... 200
20.7.2. LIN Indirect Access SFR Registers Definitions ..................................... 202
21. Controller Area Network (CAN0) ........................................................................ 210
21.1. Bosch CAN Controller Operation................................................................... 211
21.1.1. CAN Controller Timing .......................................................................... 211
21.1.2. CAN Register Access............................................................................ 212
21.1.3. Example Timing Calculation for 1 Mbit/Sec Communication ................ 212
21.2. CAN Registers............................................................................................... 214
21.2.1. CAN Controller Protocol Registers........................................................ 214
Rev. 1.2
5
C8051F55x/56x/57x
21.2.2. Message Object Interface Registers ..................................................... 214
21.2.3. Message Handler Registers.................................................................. 214
21.2.4. CAN Register Assignment .................................................................... 215
22. SMBus................................................................................................................... 218
22.1. Supporting Documents .................................................................................. 219
22.2. SMBus Configuration..................................................................................... 219
22.3. SMBus Operation .......................................................................................... 219
22.3.1. Transmitter Vs. Receiver....................................................................... 220
22.3.2. Arbitration.............................................................................................. 220
22.3.3. Clock Low Extension............................................................................. 220
22.3.4. SCL Low Timeout.................................................................................. 220
22.3.5. SCL High (SMBus Free) Timeout ......................................................... 221
22.4. Using the SMBus........................................................................................... 221
22.4.1. SMBus Configuration Register.............................................................. 221
22.4.2. SMB0CN Control Register .................................................................... 225
22.4.3. Data Register ........................................................................................ 228
22.5. SMBus Transfer Modes................................................................................. 228
22.5.1. Write Sequence (Master) ...................................................................... 229
22.5.2. Read Sequence (Master) ...................................................................... 230
22.5.3. Write Sequence (Slave) ........................................................................ 231
22.5.4. Read Sequence (Slave) ........................................................................ 232
22.6. SMBus Status Decoding................................................................................ 232
23. UART0 ................................................................................................................... 235
23.1. Baud Rate Generator .................................................................................... 235
23.2. Data Format................................................................................................... 237
23.3. Configuration and Operation ......................................................................... 238
23.3.1. Data Transmission ................................................................................ 238
23.3.2. Data Reception ..................................................................................... 238
23.3.3. Multiprocessor Communications ........................................................... 240
24. Enhanced Serial Peripheral Interface (SPI0) ..................................................... 246
24.1. Signal Descriptions........................................................................................ 247
24.1.1. Master Out, Slave In (MOSI)................................................................. 247
24.1.2. Master In, Slave Out (MISO)................................................................. 247
24.1.3. Serial Clock (SCK) ................................................................................ 247
24.1.4. Slave Select (NSS) ............................................................................... 247
24.2. SPI0 Master Mode Operation ........................................................................ 248
24.3. SPI0 Slave Mode Operation .......................................................................... 250
24.4. SPI0 Interrupt Sources .................................................................................. 250
24.5. Serial Clock Phase and Polarity .................................................................... 251
24.6. SPI Special Function Registers ..................................................................... 252
25. Timers ................................................................................................................... 259
25.1. Timer 0 and Timer 1 ...................................................................................... 261
25.1.1. Mode 0: 13-bit Counter/Timer ............................................................... 261
25.1.2. Mode 1: 16-bit Counter/Timer ............................................................... 262
25.1.3. Mode 2: 8-bit Counter/Timer with Auto-Reload..................................... 262
6
Rev. 1.2
C8051F55x/56x/57x
25.1.4. Mode 3: Two 8-bit Counter/Timers (Timer 0 Only)................................ 263
25.2. Timer 2 .......................................................................................................... 269
25.2.1. 16-bit Timer with Auto-Reload............................................................... 269
25.2.2. 8-bit Timers with Auto-Reload............................................................... 269
25.2.3. External Oscillator Capture Mode ......................................................... 270
25.3. Timer 3 .......................................................................................................... 275
25.3.1. 16-Bit Timer with Auto-Reload .............................................................. 275
25.3.2. 8-Bit Timers with Auto-Reload .............................................................. 275
25.3.3. External Oscillator Capture Mode ......................................................... 276
26. Programmable Counter Array............................................................................. 281
26.1. PCA Counter/Timer ....................................................................................... 282
26.2. PCA0 Interrupt Sources................................................................................. 283
26.3. Capture/Compare Modules ........................................................................... 283
26.3.1. Edge-triggered Capture Mode............................................................... 284
26.3.2. Software Timer (Compare) Mode.......................................................... 285
26.3.3. High-Speed Output Mode ..................................................................... 286
26.3.4. Frequency Output Mode ....................................................................... 287
26.3.5. 8-bit, 9-bit, 10-bit and 11-bit Pulse Width Modulator Modes ................. 288
26.3.6. 16-Bit Pulse Width Modulator Mode...................................................... 290
26.4. Watchdog Timer Mode .................................................................................. 291
26.4.1. Watchdog Timer Operation ................................................................... 291
26.4.2. Watchdog Timer Usage ........................................................................ 292
26.5. Register Descriptions for PCA0..................................................................... 294
27. C2 Interface .......................................................................................................... 300
27.1. C2 Interface Registers................................................................................... 300
27.2. C2 Pin Sharing .............................................................................................. 303
Rev. 1.2
7
C8051F55x/56x/57x
List of Figures
Figure 1.1. C8051F568-9 and ‘F570-5 (40-pin) Block Diagram .............................. 17
Figure 1.2. C8051F560-7 (32-pin) Block Diagram ................................................... 18
Figure 1.3. C8051F550-7 (24-pin) Block Diagram ................................................... 19
Figure 3.1. QFN-40 Pinout Diagram (Top View) ..................................................... 24
Figure 3.2. QFP-32 Pinout Diagram (Top View) ...................................................... 25
Figure 3.3. QFN-32 Pinout Diagram (Top View) ..................................................... 26
Figure 3.4. QFN-24 Pinout Diagram (Top View) ..................................................... 27
Figure 4.1. QFN-40 Package Drawing .................................................................... 28
Figure 4.2. QFN-40 Landing Diagram ..................................................................... 29
Figure 4.3. QFP-32 Package Drawing ..................................................................... 30
Figure 4.4. QFP-32 Landing Diagram ..................................................................... 31
Figure 4.5. QFN-32 Package Drawing .................................................................... 32
Figure 4.6. QFN-32 Landing Diagram ..................................................................... 33
Figure 4.7. QFN-24 Package Drawing .................................................................... 34
Figure 4.8. QFN-24 Landing Diagram ..................................................................... 35
Figure 5.1. Minimum VDD Monitor Threshold vs. System Clock Frequency ........... 39
Figure 6.1. ADC0 Functional Block Diagram ........................................................... 47
Figure 6.2. ADC0 Tracking Modes .......................................................................... 49
Figure 6.3. 12-Bit ADC Tracking Mode Example ..................................................... 50
Figure 6.4. 12-Bit ADC Burst Mode Example With Repeat Count Set to 4 ............. 51
Figure 6.5. ADC0 Equivalent Input Circuit ............................................................... 53
Figure 6.6. ADC Window Compare Example: Right-Justified Data ......................... 64
Figure 6.7. ADC Window Compare Example: Left-Justified Data ........................... 64
Figure 6.8. ADC0 Multiplexer Block Diagram .......................................................... 65
Figure 6.9. Temperature Sensor Transfer Function ................................................ 67
Figure 7.1. Voltage Reference Functional Block Diagram ....................................... 68
Figure 8.1. Comparator Functional Block Diagram ................................................. 70
Figure 8.2. Comparator Hysteresis Plot .................................................................. 71
Figure 8.3. Comparator Input Multiplexer Block Diagram ........................................ 76
Figure 9.1. External Capacitors for Voltage Regulator Input/Output—
Regulator Enabled ............................................................................................. 79
Figure 9.2. External Capacitors for Voltage Regulator Input/Output—Regulator Disabled ............................................................................................................... 80
Figure 10.1. CIP-51 Block Diagram ......................................................................... 82
Figure 11.1. C8051F55x/56x/57x Memory Map ...................................................... 92
Figure 11.2. Flash Program Memory Map ............................................................... 93
Figure 12.1. SFR Page Stack .................................................................................. 96
Figure 12.2. SFR Page Stack While Using SFR Page 0x0 To Access SPI0DAT ... 97
Figure 12.3. SFR Page Stack After CAN0 Interrupt Occurs .................................... 98
Figure 12.4. SFR Page Stack Upon PCA Interrupt Occurring During a CAN0 ISR . 99
Figure 12.5. SFR Page Stack Upon Return From PCA Interrupt .......................... 100
Figure 12.6. SFR Page Stack Upon Return From CAN0 Interrupt ........................ 101
Figure 14.1. Flash Program Memory Map ............................................................. 127
Rev. 1.2
8
C8051F55x/56x/57x
Figure 16.1. Reset Sources ................................................................................... 138
Figure 16.2. Power-On and VDD Monitor Reset Timing ....................................... 139
Figure 17.1. Multiplexed Configuration Example ................................................... 149
Figure 17.2. EMIF Operating Modes ..................................................................... 150
Figure 17.3. Multiplexed 16-bit MOVX Timing ....................................................... 153
Figure 17.4. Multiplexed 8-bit MOVX without Bank Select Timing ........................ 154
Figure 17.5. Multiplexed 8-bit MOVX with Bank Select Timing ............................. 155
Figure 18.1. Oscillator Options .............................................................................. 157
Figure 18.2. Example Clock Multiplier Output ....................................................... 162
Figure 18.3. External 32.768 kHz Quartz Crystal Oscillator Connection Diagram 167
Figure 19.1. Port I/O Functional Block Diagram .................................................... 169
Figure 19.2. Port I/O Cell Block Diagram .............................................................. 170
Figure 19.3. Peripheral Availability on Port I/O Pins .............................................. 173
Figure 19.4. Crossbar Priority Decoder in Example Configuration ........................ 174
Figure 20.1. LIN Block Diagram ............................................................................ 193
Figure 21.1. Typical CAN Bus Configuration ......................................................... 210
Figure 21.2. CAN Controller Diagram .................................................................... 211
Figure 21.3. Four segments of a CAN Bit .............................................................. 213
Figure 22.1. SMBus Block Diagram ...................................................................... 218
Figure 22.2. Typical SMBus Configuration ............................................................ 219
Figure 22.3. SMBus Transaction ........................................................................... 220
Figure 22.4. Typical SMBus SCL Generation ........................................................ 222
Figure 22.5. Typical Master Write Sequence ........................................................ 229
Figure 22.6. Typical Master Read Sequence ........................................................ 230
Figure 22.7. Typical Slave Write Sequence .......................................................... 231
Figure 22.8. Typical Slave Read Sequence .......................................................... 232
Figure 23.1. UART0 Block Diagram ...................................................................... 235
Figure 23.2. UART0 Timing Without Parity or Extra Bit ......................................... 237
Figure 23.3. UART0 Timing With Parity ................................................................ 237
Figure 23.4. UART0 Timing With Extra Bit ............................................................ 237
Figure 23.5. Typical UART Interconnect Diagram ................................................. 238
Figure 23.6. UART Multi-Processor Mode Interconnect Diagram ......................... 240
Figure 24.1. SPI Block Diagram ............................................................................ 246
Figure 24.2. Multiple-Master Mode Connection Diagram ...................................... 249
Figure 24.3. 3-Wire Single Master and 3-Wire Single Slave Mode Connection Diagram
............................................................................................................. 249
Figure 24.4. 4-Wire Single Master Mode and 4-Wire Slave Mode Connection Diagram
............................................................................................................. 249
Figure 24.5. Master Mode Data/Clock Timing ....................................................... 251
Figure 24.6. Slave Mode Data/Clock Timing (CKPHA = 0) ................................... 252
Figure 24.7. Slave Mode Data/Clock Timing (CKPHA = 1) ................................... 252
Figure 24.8. SPI Master Timing (CKPHA = 0) ....................................................... 256
Figure 24.9. SPI Master Timing (CKPHA = 1) ....................................................... 256
Figure 24.10. SPI Slave Timing (CKPHA = 0) ....................................................... 257
Figure 24.11. SPI Slave Timing (CKPHA = 1) ....................................................... 257
9
Rev. 1.2
C8051F55x/56x/57x
Figure 25.1. T0 Mode 0 Block Diagram ................................................................. 262
Figure 25.2. T0 Mode 2 Block Diagram ................................................................. 263
Figure 25.3. T0 Mode 3 Block Diagram ................................................................. 264
Figure 25.4. Timer 2 16-Bit Mode Block Diagram ................................................. 269
Figure 25.5. Timer 2 8-Bit Mode Block Diagram ................................................... 270
Figure 25.6. Timer 2 External Oscillator Capture Mode Block Diagram ................ 271
Figure 25.7. Timer 3 16-Bit Mode Block Diagram ................................................. 275
Figure 25.8. Timer 3 8-Bit Mode Block Diagram ................................................... 276
Figure 25.9. Timer 3 External Oscillator Capture Mode Block Diagram ................ 277
Figure 26.1. PCA Block Diagram ........................................................................... 281
Figure 26.2. PCA Counter/Timer Block Diagram ................................................... 282
Figure 26.3. PCA Interrupt Block Diagram ............................................................ 283
Figure 26.4. PCA Capture Mode Diagram ............................................................. 285
Figure 26.5. PCA Software Timer Mode Diagram ................................................. 286
Figure 26.6. PCA High-Speed Output Mode Diagram ........................................... 287
Figure 26.7. PCA Frequency Output Mode ........................................................... 288
Figure 26.8. PCA 8-Bit PWM Mode Diagram ........................................................ 289
Figure 26.9. PCA 9, 10 and 11-Bit PWM Mode Diagram ...................................... 290
Figure 26.10. PCA 16-Bit PWM Mode ................................................................... 291
Figure 26.11. PCA Module 2 with Watchdog Timer Enabled ................................ 292
Figure 27.1. Typical C2 Pin Sharing ...................................................................... 303
Rev. 1.2
10
C8051F55x/56x/57x
List of Tables
Table 2.1. Product Selection Guide ......................................................................... 21
Table 3.1. Pin Definitions for the C8051F55x/56x/57x ............................................ 22
Table 4.1. QFN-40 Package Dimensions ................................................................ 28
Table 4.2. QFN-40 Landing Diagram Dimensions ................................................... 29
Table 4.3. QFP-32 Package Dimensions ................................................................ 30
Table 4.4. QFP-32 Landing Diagram Dimensions ................................................... 31
Table 4.5. QFN-32 Package Dimensions ................................................................ 32
Table 4.6. QFN-32 Landing Diagram Dimensions ................................................... 33
Table 4.7. QFN-24 Package Dimensions ................................................................ 34
Table 4.8. QFN-24 Landing Diagram Dimensions ................................................... 35
Table 5.1. Absolute Maximum Ratings .................................................................... 36
Table 5.2. Global Electrical Characteristics ............................................................. 37
Table 5.3. Port I/O DC Electrical Characteristics ..................................................... 40
Table 5.4. Reset Electrical Characteristics .............................................................. 41
Table 5.5. Flash Electrical Characteristics .............................................................. 41
Table 5.6. Internal High-Frequency Oscillator Electrical Characteristics ................. 42
Table 5.7. Clock Multiplier Electrical Specifications ................................................ 43
Table 5.8. Voltage Regulator Electrical Characteristics .......................................... 43
Table 5.9. ADC0 Electrical Characteristics .............................................................. 44
Table 5.10. Temperature Sensor Electrical Characteristics .................................... 45
Table 5.11. Voltage Reference Electrical Characteristics ....................................... 45
Table 5.12. Comparator 0 and Comparator 1 Electrical Characteristics ................. 46
Table 10.1. CIP-51 Instruction Set Summary .......................................................... 84
Table 12.1. Special Function Register (SFR) Memory Map for Pages 0x00 and 0x0F
106
Table 12.2. Special Function Register (SFR) Memory Map for Page 0x0C .......... 107
Table 12.3. Special Function Registers ................................................................. 108
Table 13.1. Interrupt Summary .............................................................................. 114
Table 14.1. Flash Security Summary .................................................................... 128
Table 17.1. EMIF Pinout (C8051F568-9 and ‘F570-5) .......................................... 146
Table 17.2. AC Parameters for External Memory Interface ................................... 156
Table 19.1. Port I/O Assignment for Analog Functions ......................................... 171
Table 19.2. Port I/O Assignment for Digital Functions ........................................... 172
Table 19.3. Port I/O Assignment for External Digital Event Capture Functions .... 172
Table 20.1. Baud Rate Calculation Variable Ranges ............................................ 194
Table 20.2. Manual Baud Rate Parameters Examples ......................................... 196
Table 20.3. Autobaud Parameters Examples ........................................................ 197
Table 20.4. LIN Registers* (Indirectly Addressable) .............................................. 202
Table 21.1. Background System Information ........................................................ 212
Table 21.2. Standard CAN Registers and Reset Values ....................................... 215
Table 22.1. SMBus Clock Source Selection .......................................................... 222
Table 22.2. Minimum SDA Setup and Hold Times ................................................ 223
Rev. 1.2
11
C8051F55x/56x/57x
Table 22.3. Sources for Hardware Changes to SMB0CN ..................................... 227
Table 22.4. SMBus Status Decoding ..................................................................... 233
Table 23.1. Baud Rate Generator Settings for Standard Baud Rates ................... 236
Table 24.1. SPI Slave Timing Parameters ............................................................ 258
Table 26.1. PCA Timebase Input Options ............................................................. 282
Table 26.2. PCA0CPM and PCA0PWM Bit Settings for
PCA Capture/Compare Modules ........................................................ 284
Table 26.3. Watchdog Timer Timeout Intervals1 ................................................... 293
12
Rev. 1.2
C8051F55x/56x/57x
List of Registers
SFR Definition 6.4. ADC0CF: ADC0 Configuration ...................................................... 58
SFR Definition 6.5. ADC0H: ADC0 Data Word MSB .................................................... 59
SFR Definition 6.6. ADC0L: ADC0 Data Word LSB ...................................................... 59
SFR Definition 6.7. ADC0CN: ADC0 Control ................................................................ 60
SFR Definition 6.8. ADC0TK: ADC0 Tracking Mode Select ......................................... 61
SFR Definition 6.9. ADC0GTH: ADC0 Greater-Than Data High Byte .......................... 62
SFR Definition 6.10. ADC0GTL: ADC0 Greater-Than Data Low Byte .......................... 62
SFR Definition 6.11. ADC0LTH: ADC0 Less-Than Data High Byte .............................. 63
SFR Definition 6.12. ADC0LTL: ADC0 Less-Than Data Low Byte ............................... 63
SFR Definition 6.13. ADC0MX: ADC0 Channel Select ................................................. 66
SFR Definition 7.1. REF0CN: Reference Control ......................................................... 69
SFR Definition 8.1. CPT0CN: Comparator0 Control ..................................................... 72
SFR Definition 8.2. CPT0MD: Comparator0 Mode Selection ....................................... 73
SFR Definition 8.3. CPT1CN: Comparator1 Control ..................................................... 74
SFR Definition 8.4. CPT1MD: Comparator1 Mode Selection ....................................... 75
SFR Definition 8.5. CPT0MX: Comparator0 MUX Selection ........................................ 77
SFR Definition 8.6. CPT1MX: Comparator1 MUX Selection ........................................ 78
SFR Definition 9.1. REG0CN: Regulator Control .......................................................... 80
SFR Definition 10.1. DPL: Data Pointer Low Byte ........................................................ 88
SFR Definition 10.2. DPH: Data Pointer High Byte ....................................................... 88
SFR Definition 10.3. SP: Stack Pointer ......................................................................... 89
SFR Definition 10.4. ACC: Accumulator ....................................................................... 89
SFR Definition 10.5. B: B Register ................................................................................ 89
SFR Definition 10.6. PSW: Program Status Word ........................................................ 90
SFR Definition 10.7. SNn: Serial Number n .................................................................. 91
SFR Definition 12.1. SFR0CN: SFR Page Control ..................................................... 102
SFR Definition 12.2. SFRPAGE: SFR Page ............................................................... 103
SFR Definition 12.3. SFRNEXT: SFR Next ................................................................ 104
SFR Definition 12.4. SFRLAST: SFR Last .................................................................. 105
SFR Definition 13.1. IE: Interrupt Enable .................................................................... 116
SFR Definition 13.2. IP: Interrupt Priority .................................................................... 117
SFR Definition 13.3. EIE1: Extended Interrupt Enable 1 ............................................ 118
SFR Definition 13.4. EIP1: Extended Interrupt Priority 1 ............................................ 119
SFR Definition 13.5. EIE2: Extended Interrupt Enable 2 ............................................ 120
SFR Definition 13.6. EIP2: Extended Interrupt Priority Enabled 2 .............................. 121
SFR Definition 13.7. IT01CF: INT0/INT1 Configuration .............................................. 123
SFR Definition 14.1. PSCTL: Program Store R/W Control ......................................... 131
SFR Definition 14.2. FLKEY: Flash Lock and Key ...................................................... 132
SFR Definition 14.3. FLSCL: Flash Scale ................................................................... 133
SFR Definition 14.4. CCH0CN: Cache Control ........................................................... 134
SFR Definition 14.5. ONESHOT: Flash Oneshot Period ............................................ 134
SFR Definition 15.1. PCON: Power Control ................................................................ 137
SFR Definition 16.1. VDM0CN: VDD Monitor Control ................................................ 141
Rev. 1.2
13
C8051F55x/56x/57x
SFR Definition 16.2. RSTSRC: Reset Source ............................................................ 143
SFR Definition 17.1. EMI0CN: External Memory Interface Control ............................ 147
SFR Definition 17.2. EMI0CF: External Memory Configuration .................................. 148
SFR Definition 17.3. EMI0TC: External Memory Timing Control ................................ 152
SFR Definition 18.1. CLKSEL: Clock Select ............................................................... 158
SFR Definition 18.2. OSCICN: Internal Oscillator Control .......................................... 160
SFR Definition 18.3. OSCICRS: Internal Oscillator Coarse Calibration ...................... 161
SFR Definition 18.4. OSCIFIN: Internal Oscillator Fine Calibration ............................ 161
SFR Definition 18.5. CLKMUL: Clock Multiplier .......................................................... 163
SFR Definition 18.6. OSCXCN: External Oscillator Control ........................................ 165
SFR Definition 19.1. XBR0: Port I/O Crossbar Register 0 .......................................... 176
SFR Definition 19.2. XBR1: Port I/O Crossbar Register 1 .......................................... 177
SFR Definition 19.3. XBR2: Port I/O Crossbar Register 1 .......................................... 178
SFR Definition 19.4. P0MASK: Port 0 Mask Register ................................................. 179
SFR Definition 19.5. P0MAT: Port 0 Match Register .................................................. 179
SFR Definition 19.6. P1MASK: Port 1 Mask Register ................................................. 180
SFR Definition 19.7. P1MAT: Port 1 Match Register .................................................. 180
SFR Definition 19.8. P2MASK: Port 2 Mask Register ................................................. 181
SFR Definition 19.9. P2MAT: Port 2 Match Register .................................................. 181
SFR Definition 19.10. P3MASK: Port 3 Mask Register ............................................... 182
SFR Definition 19.11. P3MAT: Port 3 Match Register ................................................ 182
SFR Definition 19.12. P0: Port 0 ................................................................................. 183
SFR Definition 19.13. P0MDIN: Port 0 Input Mode ..................................................... 184
SFR Definition 19.14. P0MDOUT: Port 0 Output Mode .............................................. 184
SFR Definition 19.15. P0SKIP: Port 0 Skip ................................................................. 185
SFR Definition 19.16. P1: Port 1 ................................................................................. 185
SFR Definition 19.17. P1MDIN: Port 1 Input Mode ..................................................... 186
SFR Definition 19.18. P1MDOUT: Port 1 Output Mode .............................................. 186
SFR Definition 19.19. P1SKIP: Port 1 Skip ................................................................. 187
SFR Definition 19.20. P2: Port 2 ................................................................................. 187
SFR Definition 19.21. P2MDIN: Port 2 Input Mode ..................................................... 188
SFR Definition 19.22. P2MDOUT: Port 2 Output Mode .............................................. 188
SFR Definition 19.23. P2SKIP: Port 2 Skip ................................................................. 189
SFR Definition 19.24. P3: Port 3 ................................................................................. 189
SFR Definition 19.25. P3MDIN: Port 3 Input Mode ..................................................... 190
SFR Definition 19.26. P3MDOUT: Port 3 Output Mode .............................................. 190
SFR Definition 19.27. P3SKIP: Port 3Skip .................................................................. 191
SFR Definition 19.28. P4: Port 4 ................................................................................. 191
SFR Definition 19.29. P4MDOUT: Port 4 Output Mode .............................................. 192
SFR Definition 20.1. LIN0ADR: LIN0 Indirect Address Register ................................. 200
SFR Definition 20.2. LIN0DAT: LIN0 Indirect Data Register ....................................... 200
SFR Definition 20.3. LIN0CF: LIN0 Control Mode Register ........................................ 201
SFR Definition 21.1. CAN0CFG: CAN Clock Configuration ........................................ 217
SFR Definition 22.1. SMB0CF: SMBus Clock/Configuration ...................................... 224
SFR Definition 22.2. SMB0CN: SMBus Control .......................................................... 226
14
Rev. 1.2
C8051F55x/56x/57x
SFR Definition 22.3. SMB0DAT: SMBus Data ............................................................ 228
SFR Definition 23.1. SCON0: Serial Port 0 Control .................................................... 241
SFR Definition 23.2. SMOD0: Serial Port 0 Control .................................................... 243
SFR Definition 23.3. SBUF0: Serial (UART0) Port Data Buffer .................................. 244
SFR Definition 23.4. SBCON0: UART0 Baud Rate Generator Control ...................... 244
SFR Definition 23.6. SBRLL0: UART0 Baud Rate Generator Reload Low Byte ........ 245
SFR Definition 23.5. SBRLH0: UART0 Baud Rate Generator Reload High Byte ....... 245
SFR Definition 24.1. SPI0CFG: SPI0 Configuration ................................................... 253
SFR Definition 24.2. SPI0CN: SPI0 Control ............................................................... 254
SFR Definition 24.3. SPI0CKR: SPI0 Clock Rate ....................................................... 255
SFR Definition 24.4. SPI0DAT: SPI0 Data ................................................................. 255
SFR Definition 25.1. CKCON: Clock Control .............................................................. 260
SFR Definition 25.2. TCON: Timer Control ................................................................. 265
SFR Definition 25.3. TMOD: Timer Mode ................................................................... 266
SFR Definition 25.4. TL0: Timer 0 Low Byte ............................................................... 267
SFR Definition 25.5. TL1: Timer 1 Low Byte ............................................................... 267
SFR Definition 25.6. TH0: Timer 0 High Byte ............................................................. 268
SFR Definition 25.7. TH1: Timer 1 High Byte ............................................................. 268
SFR Definition 25.8. TMR2CN: Timer 2 Control ......................................................... 272
SFR Definition 25.9. TMR2RLL: Timer 2 Reload Register Low Byte .......................... 273
SFR Definition 25.10. TMR2RLH: Timer 2 Reload Register High Byte ...................... 273
SFR Definition 25.11. TMR2L: Timer 2 Low Byte ....................................................... 274
SFR Definition 25.12. TMR2H Timer 2 High Byte ....................................................... 274
SFR Definition 25.13. TMR3CN: Timer 3 Control ....................................................... 278
SFR Definition 25.14. TMR3RLL: Timer 3 Reload Register Low Byte ........................ 279
SFR Definition 25.15. TMR3RLH: Timer 3 Reload Register High Byte ...................... 279
SFR Definition 25.16. TMR3L: Timer 3 Low Byte ....................................................... 280
SFR Definition 25.17. TMR3H Timer 3 High Byte ....................................................... 280
SFR Definition 26.1. PCA0CN: PCA Control .............................................................. 294
SFR Definition 26.2. PCA0MD: PCA Mode ................................................................ 295
SFR Definition 26.3. PCA0PWM: PCA PWM Configuration ....................................... 296
SFR Definition 26.4. PCA0CPMn: PCA Capture/Compare Mode .............................. 297
SFR Definition 26.5. PCA0L: PCA Counter/Timer Low Byte ...................................... 298
SFR Definition 26.6. PCA0H: PCA Counter/Timer High Byte ..................................... 298
SFR Definition 26.7. PCA0CPLn: PCA Capture Module Low Byte ............................. 299
SFR Definition 26.8. PCA0CPHn: PCA Capture Module High Byte ........................... 299
Rev. 1.2
15
C8051F55x/56x/57x
1. System Overview
C8051F55x/56x/57x devices are fully integrated mixed-signal System-on-a-Chip MCUs. Highlighted features are listed below. Refer to Table 2.1 for specific product feature selection and part ordering numbers.
High-speed pipelined 8051-compatible microcontroller core (up to 50 MIPS)
In-system, full-speed, non-intrusive debug interface (on-chip)
Controller Area Network (CAN 2.0B) Controller with 32 message objects, each with its own indentifier
mask (C8051F550/1/4/5, ‘F560/1/4/5/8/9, and ‘F572/3)
LIN 2.1 peripheral (fully backwards compatible, master and slave modes) (C8051F550/2/4/6,
‘F560/2/4/6/8, and ‘F570/2/4)
True 12-bit 200 ksps 32-channel single-ended ADC with analog multiplexer
Precision programmable 24 MHz internal oscillator that is within ±0.5% across the temperature range
and for VDD voltages greater than or equal to the on-chip voltage regulator minimum output at the low
setting. The oscillator is within +1.0% for VDD voltages below this minimum output setting.
On-chip Clock Multiplier to reach up to 50 MHz
32 kB (C8051F550-3, ‘F560-3, ‘F568-9, and ‘F570-1) or 16 kB (C8051F554-7, ‘F564-7, and ‘F572-5) of
on-chip Flash memory
2304 bytes of on-chip RAM
SMBus/I2C, Enhanced UART, and Enhanced SPI serial interfaces implemented in hardware
Four general-purpose 16-bit timers
External Data Memory Interface (C8051F568-9 and ‘F570-5) with 64 kB address space
Programmable Counter/Timer Array (PCA) with six capture/compare modules and Watchdog Timer
function
On-chip Voltage Regulator
On-chip Power-On Reset, VDD Monitor, and Temperature Sensor
On-chip Voltage Comparator
33, 25, or 18 Port I/O (5 V push-pull)
With on-chip Voltage Regulator, Power-On Reset, VDD monitor, Watchdog Timer, and clock oscillator, the
C8051F55x/56x/57x devices are truly stand-alone System-on-a-Chip solutions. The Flash memory can be
reprogrammed even in-circuit, providing non-volatile data storage, and also allowing field upgrades of the
8051 firmware. User software has complete control of all peripherals, and may individually shut down any
or all peripherals for power savings.
The on-chip Silicon Labs 2-Wire (C2) Development Interface allows non-intrusive (uses no on-chip
resources), full speed, in-circuit debugging using the production MCU installed in the final application. This
debug logic supports inspection and modification of memory and registers, setting breakpoints, single
stepping, run and halt commands. All analog and digital peripherals are fully functional while debugging
using C2. The two C2 interface pins can be shared with user functions, allowing in-system debugging without occupying package pins.
The devices are specified for 1.8 V to 5.25 V operation over the automotive temperature range (–40 to
+125 °C). The C8051F568-9 and ‘F570-5 are available in 40-pin QFN packages, the C8051F560-7
devices are available in 32-pin QFP and QFN packages, and the C8051F550-7 are available in 24-pin
QFN packages. All package options are lead-free and RoHS compliant. See Table 2.1 for ordering information. Block diagrams are included in Figure 1.1, Figure 1.2, and Figure 1.3.
Rev. 1.2
16
C8051F55x/56x/57x
VIO
Power On
Reset
Reset
C2CK/RST
Port I/O Configuration
CIP-51 8051 Controller
Core (50 MHz)
Debug /
Programming
Hardware
Port 1
Drivers
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
Port 2
Drivers
P2.0
P2.1
P2.2
P2.3
P2.4
P2.5
P2.6
P2.7
Port 3
Drivers
P3.0
P3.1
P3.2
P3.3
P3.4
P3.5
P3.6
P3.7
Digital Peripherals
32 or 16 kB Flash
Program Memory
UART0
256 Byte RAM
Timers 0,
1, 2, 3
2 kB XRAM
6 channel
PCA/WDT
C2D
Priority
Crossbar
Decoder
LIN 2.1
VREGIN
Port 0
Drivers
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
Voltage Regulator
(LDO)
CAN 2.0B
SPI
VDD
I2C
GND
System Clock Setup
SFR
Bus
Crossbar Control
External Memory Interface
XTAL1 XTAL2
Internal Oscillator
(±0.5%)
External Oscillator
Analog Peripherals
Voltage
Reference
Clock Multiplier
VDD
VREF
VREF
12-bit
200ksps
ADC
A
M
U
X
CP0, CP0A
VDDA
Comparator 0
VDD
VREF
P0 – P3
Temp
Sensor
GND
Port 4
Driver
+
-
GNDA
CP1, CP1A
Comparator 1
+
-
Figure 1.1. C8051F568-9 and ‘F570-5 (40-pin) Block Diagram
17
Rev. 1.2
P4.0/C2D
C8051F55x/56x/57x
VIO
Power On
Reset
Debug /
Programming
Hardware
32 or 16 kB Flash
Program Memory
UART0
256 Byte RAM
Timers 0,
1, 2, 3
2 kB XRAM
6 channel
PCA/WDT
C2D
Port 1
Drivers
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
Port 2
Drivers
P2.0
P2.1
P2.2
P2.3
P2.4
P2.5
P2.6
P2.7
Priority
Crossbar
Decoder
LIN 2.1
VREGIN
Port 0
Drivers
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
Digital Peripherals
Reset
C2CK/RST
Port I/O Configuration
CIP-51 8051 Controller
Core (50 MHz)
Voltage Regulator
(LDO)
CAN 2.0B
SPI
VDD
I2C
GND
System Clock Setup
SFR
Bus
Crossbar Control
XTAL1 XTAL2
Internal Oscillator
(±0.5%)
External Oscillator
Analog Peripherals
Voltage
Reference
Clock Multiplier
VDD
VREF
P3.0/C2D
VREF
12-bit
200ksps
ADC
A
M
U
X
CP0, CP0A
VDDA
Port 3
Driver
Comparator 0
VDD
VREF
P0 – P3
Temp
Sensor
GND
+
-
GNDA
CP1, CP1A
Comparator 1
+
-
Figure 1.2. C8051F560-7 (32-pin) Block Diagram
Rev. 1.2
18
C8051F55x/56x/57x
VIO
Power On
Reset
Debug /
Programming
Hardware
32 or 16 kB Flash
Program Memory
UART0
256 Byte RAM
Timers 0,
1, 2, 3
2 kB XRAM
6 channel
PCA/WDT
C2D
Port 1
Drivers
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
Port 2
Drivers
P2.0
P2.1/C2D
Priority
Crossbar
Decoder
LIN 2.1
VREGIN
Port 0
Drivers
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
Digital Peripherals
Reset
C2CK/RST
Port I/O Configuration
CIP-51 8051 Controller
Core (50 MHz)
Voltage Regulator
(LDO)
CAN 2.0B
SPI
VDD
I2C
GND
System Clock Setup
SFR
Bus
Crossbar Control
XTAL1 XTAL2
Internal Oscillator
(±0.5%)
External Oscillator
Analog Peripherals
Voltage
Reference
Clock Multiplier
VDD
VREF
VREF
12-bit
200ksps
ADC
A
M
U
X
CP0, CP0A
Comparator 0
VDD
VREF
P0 – P2
Temp
Sensor
GND
+
-
GNDA
CP1, CP1A
Comparator 1
+
-
Figure 1.3. C8051F550-7 (24-pin) Block Diagram
19
Rev. 1.2
C8051F55x/56x/57x
2. Ordering Information
The following features are common to all devices in this family:
50 MHz system clock and 50 MIPS throughput (peak)
2304 bytes of RAM (256 internal bytes and 2048 XRAM bytes)
SMBus/I2C, Enhanced SPI, Enhanced UART
Four Timers
Six Programmable Counter Array channels
Internal 24 MHz oscillator
Internal Voltage Regulator
12-bit, 200 ksps ADC
Internal Voltage Reference and Temperature Sensor
Two Analog Comparators
Table 2.1 shows the feature that differentiate the devices in this family.
Rev. 1.2
20
C8051F55x/56x/57x
External Mem. Interface
25
—
QFN-32
C8051F551-IM
32
—
18 —
QFN-24
C8051F564-IQ
16
25
—
QFP-32
C8051F552-IM
32
—
18 —
QFN-24
C8051F565-IM
16
—
25
—
QFN-32
C8051F553-IM
32
— —
18 —
QFN-24
C8051F565-IQ
16
—
25
—
QFP-32
C8051F554-IM
16
18 —
QFN-24
C8051F566-IM
16
—
25
—
QFN-32
C8051F555-IM
16
—
18 —
QFN-24
C8051F566-IQ
16
—
25
—
QFP-32
C8051F556-IM
16
—
18 —
QFN-24
C8051F567-IM
16
—
—
25
—
QFN-32
C8051F557-IM
16
— —
18 —
QFN-24
C8051F567-IQ
16
—
—
25
—
QFP-32
C8051F560-IM
32
25 —
QFN-32
C8051F568-IM
32
33
QFN-40
C8051F560-IQ
32
25 —
QFP-32
C8051F569-IM
32
—
33
QFN-40
C8051F561-IM
32
—
25 —
QFN-32
C8051F570-IM
32
—
33
QFN-40
C8051F561-IQ
32
—
25 —
QFP-32
C8051F571-IM
32
—
—
33
QFN-40
C8051F562-IM
32
—
25 —
QFN-32
C8051F572-IM
16
33
QFN-40
C8051F562-IQ
32
—
25 —
QFP-32
C8051F573-IM
16
—
33
QFN-40
C8051F563-IM
32
— —
25 —
QFN-32
C8051F574-IM
16
—
33
QFN-40
C8051F563-IQ
32
— —
25 —
QFP-32
C8051F575-IM
16
—
—
33
QFN-40
Package
Package
Digital Port I/Os
LIN2.1
16
CAN2.0B
C8051F564-IM
Flash Memory (kB)
QFN-24
Ordering Part Number
18 —
Digital Port I/Os
LIN2.1
CAN2.0B
32
Flash Memory (kB)
C8051F550-IM
Ordering Part Number
External Mem. Interface
Table 2.1. Product Selection Guide
Note: The suffix of the part number indicates the device rating and the package. All devices are RoHS compliant.
All devices in Table 2.1 are also available in an automotive version. For the automotive version, the -I in the
ordering part number is replaced with -A. For example, the automotive version of the C8051F550-IM is the
C8051F550-AM.
The -AM and -AQ devices receive full automotive quality production status, including AEC-Q100 qualification, registration with International Material Data System (IMDS) and Part Production Approval Process
(PPAP) documentation. PPAP documentation is available at www.silabs.com with a registered and NDA
approved user account. The -AM and -AQ devices enable high volume automotive OEM applications with
their enhanced testing and processing. Please contact Silicon Labs sales for more information regarding
–AM and -AQ devices for your automotive project.
21
Rev. 1.2
C8051F55x/56x/57x
3. Pin Definitions
Table 3.1. Pin Definitions for the C8051F55x/56x/57x
Name
Pin
Pin
Pin
Type
Description
40-pin
32-pin
24-pin
packages packages packages
VDD
4
4
3
Digital Supply Voltage. Must be connected.
GND
6
6
4
Digital Ground. Must be connected.
VDDA
5
5
—
Analog Supply Voltage. Must be connected.
GNDA
7
7
5
Analog Ground. Must be connected.
VREGIN
3
3
2
Voltage Regulator Input
VIO
2
2
1
Port I/O Supply Voltage. Must be connected.
RST/
10
10
8
C2CK
P4.0/
9
—
—
C2D
D I/O
Device Reset. Open-drain output of internal
POR or VDD Monitor.
D I/O
Clock signal for the C2 Debug Interface.
D I/O or A In Port 4.0. See SFR Definition 19.28.
D I/O
P3.0/
9
—
C2D
D I/O or A In Port 3.0. See SFR Definition 19.24.
D I/O
P2.1/
—
7
C2D
Bi-directional data signal for the C2 Debug
Interface.
Bi-directional data signal for the C2 Debug
Interface.
D I/O or A In Port 2.1. See SFR Definition 19.20.
D I/O
Bi-directional data signal for the C2 Debug
Interface.
P0.0
8
8
6
D I/O or A In Port 0.0. See SFR Definition 19.12.
P0.1
1
1
24
D I/O or A In Port 0.1
P0.2
40
32
23
D I/O or A In Port 0.2
P0.3
39
31
22
D I/O or A In Port 0.3
P0.4
38
30
21
D I/O or A In Port 0.4
P0.5
37
29
20
D I/O or A In Port 0.5
P0.6
36
28
19
D I/O or A In Port 0.6
P0.7
35
27
18
D I/O or A In Port 0.7
Rev. 1.2
22
C8051F55x/56x/57x
Table 3.1. Pin Definitions for the C8051F55x/56x/57x (Continued)
Name
Pin
Pin
Pin
Type
Description
40-pin
32-pin
24-pin
packages packages packages
23
P1.0
34
26
17
D I/O or A In Port 1.0. See SFR Definition 19.16.
P1.1
33
25
16
D I/O or A In Port 1.1.
P1.2
32
24
15
D I/O or A In Port 1.2.
P1.3
31
23
14
D I/O or A In Port 1.3.
P1.4
30
22
13
D I/O or A In Port 1.4.
P1.5
29
21
12
D I/O or A In Port 1.5.
P1.6
28
20
11
D I/O or A In Port 1.6.
P1.7
27
19
10
D I/O or A In Port 1.7.
P2.0
26
18
9
D I/O or A In Port 2.0. See SFR Definition 19.20.
P2.1
25
17
—
D I/O or A In Port 2.1.
P2.2
24
16
—
D I/O or A In Port 2.2.
P2.3
23
15
—
D I/O or A In Port 2.3.
P2.4
22
14
—
D I/O or A In Port 2.4.
P2.5
21
13
—
D I/O or A In Port 2.5.
P2.6
20
12
—
D I/O or A In Port 2.6.
P2.7
19
11
—
D I/O or A In Port 2.7.
P3.0
18
—
—
D I/O or A In Port 3.0. See SFR Definition 19.24.
P3.1
17
—
—
D I/O or A In Port 3.1.
P3.2
16
—
—
D I/O or A In Port 3.2.
P3.3
15
—
—
D I/O or A In Port 3.3.
P3.4
14
—
—
D I/O or A In Port 3.4.
P3.5
13
—
—
D I/O or A In Port 3.5.
P3.6
12
—
—
D I/O or A In Port 3.6.
P3.7
11
—
—
D I/O or A In Port 3.7.
Rev. 1.2
P0.2 / XTAL1
P0.3 / XTAL2
P0.4 / UART0 TX
P0.5 / UART0 RX
P0.6 / CAN TX
P0.7 / CAN RX
P1.0
P1.1
P1.2
P1.3
40
39
38
37
36
35
34
33
32
31
C8051F55x/56x/57x
P0.1 / CNVSTR
1
30
P1.4
VIO
2
29
P1.5
VREGIN
3
28
P1.6
VDD
4
27
P1.7
VDDA
5
26
P2.0
GND
6
25
P2.1
GNDA
7
24
P2.2
P0.0 / VREF
8
23
P2.3
C8051F568-IM
C8051F569-IM
C8051F570-IM
C8051F571-IM
C8051F572-IM
C8051F573-IM
C8051F574-IM
C8051F575-IM
(Top View)
GND
14
15
16
17
18
19
20
P3.3
P3.2
P3.1
P3.0
P2.7
P2.6
P2.5
P3.4
21
13
10
P3.5
RST / C2CK
12
P2.4
P3.6
22
11
9
P3.7
P4.0 / C2D
Figure 3.1. QFN-40 Pinout Diagram (Top View)
Rev. 1.2
24
P0.4 / UART0 TX
P0.5 / UART0 RX
P0.6 / CAN TX
P0.7 / CAN RX
P1.0
P1.1
29
28
27
26
25
P0.3 / XTAL2
31
30
P0.2 / XTAL1
16
8
P2.2
P0.0 / VREF
15
7
P2.3
GNDA
14
6
P2.4
GND
13
5
P2.5
VDDA
12
4
P2.6
VDD
11
3
P2.7
VREGIN
10
2
RST / C2CK
VIO
C8051F560-IQ
C8051F561-IQ
C8051F562-IQ
C8051F563-IQ
C8051F564-IQ
C8051F565-IQ
C8051F566-IQ
C8051F567-IQ
(Top View)
9
1
P3.0 / C2D
P0.1 / CNVSTR
32
C8051F55x/56x/57x
Figure 3.2. QFP-32 Pinout Diagram (Top View)
25
Rev. 1.2
24
P1.2
23
P1.3
22
P1.4
21
P1.5
20
P1.6
19
P1.7
18
P2.0
17
P2.1
P0.2 / XTAL1
P0.3 / XTAL2
P0.4 / UART0 TX
P0.5 / UART0 RX
P0.6 / CAN TX
P0.7 / CAN RX
P1.0
P1.1
31
30
29
28
27
26
25
16
8
P2.2
P0.0 / VREF
GND
15
7
P2.3
GNDA
14
6
P2.4
GND
13
5
P2.5
VDDA
12
4
P2.6
VDD
11
3
P2.7
VREGIN
C8051F560-IM
C8051F561-IM
C8051F562-IM
C8051F563-IM
C8051F564-IM
C8051F565-IM
C8051F566-IM
C8051F567-IM
(Top View)
10
2
RST / C2CK
VIO
9
1
P3.0 / C2D
P0.1 / CNVSTR
32
C8051F55x/56x/57x
24
P1.2
23
P1.3
22
P1.4
21
P1.5
20
P1.6
19
P1.7
18
P2.0
17
P2.1
Figure 3.3. QFN-32 Pinout Diagram (Top View)
Rev. 1.2
26
VIO
P0.3/XTAL2
P0.4/UART0 TX
P0.5/UART0 RX
P0.6/CAN0 TX
21
20
19
P0.2/XTAL1
23
22
P0.1/CNVSTR
24
C8051F55x/56x/57x
1
VREGIN
2
VDD
3
GND
4
GNDA
5
P0.0/VREF
6
C8051F550-IM
C8051F551-IM
C8051F552-IM
C8051F553-IM
C8051F554-IM
C8051F555-IM
C8051F556-IM
C8051F557-IM
(Top View)
18
P0.7/CAN0 RX
17
P1.0
16
P1.1
15
P1.2
14
P1.3
13
P1.4
7
8
9
10
11
12
P2.1/C2D
RST/C2CK
P2.0
P1.7
P1.6
P1.5
GND
Figure 3.4. QFN-24 Pinout Diagram (Top View)
27
Rev. 1.2
C8051F55x/56x/57x
4. Package Specifications
4.1. QFN-40 Package Specifications
Figure 4.1. QFN-40 Package Drawing
Table 4.1. QFN-40 Package Dimensions
Dimension
Min
Typ
Max
Dimension
Min
Typ
Max
A
A1
b
D
D2
e
E
0.80
0.00
0.18
0.85
0.90
0.05
0.28
E2
L
L1
aaa
bbb
ddd
eee
4.00
0.35
4.10
0.40
4.20
0.45
0.10
0.10
0.10
0.05
0.08
4.00
0.23
6.00 BSC
4.10
0.50 BSC
6.00 BSC
4.20
Notes:
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
3. This drawing conforms to JEDEC Solid State Outline MO-220, variation VJJD-5, except for
features A, D2, and E2 which are toleranced per supplier designation.
4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body
Components.
Rev. 1.2
28
C8051F55x/56x/57x
Figure 4.2. QFN-40 Landing Diagram
Table 4.2. QFN-40 Landing Diagram Dimensions
Dimension
Min
Max
Dimension
Min
Max
C1
5.80
5.90
X2
4.10
4.20
C2
5.80
5.90
Y1
0.75
0.85
Y2
4.10
4.20
e
X1
0.50 BSC
0.15
0.25
Notes:
General
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimension and Tolerancing is per the ANSI Y14.5M-1994 specification.
3. This Land Pattern Design is based on the IPC-SM-7351 guidelines.
4. All dimensions shown are at Maximum Material Condition (MMC). Least Material Condition (LMC) is
calculated based on a Fabrication Allowance of 0.05 mm.
Solder Mask Design
5. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the
metal pad is to be 60 μm minimum, all the way around the pad.
Stencil Design
6. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure
good solder paste release.
7. The stencil thickness should be 0.125 mm (5 mils).
8. The ratio of stencil aperture to land pad size should be 1:1 for all perimeter pads.
9. A 4x4 array of 0.80 mm square openings on a 1.05 mm pitch should be used for the center ground pad.
Card Assembly
10. A No-Clean, Type-3 solder paste is recommended.
11. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body
Components.
29
Rev. 1.2
C8051F55x/56x/57x
4.2. QFP-32 Package Specifications
Figure 4.3. QFP-32 Package Drawing
Table 4.3. QFP-32 Package Dimensions
Dimension
A
A1
A2
b
c
D
D1
e
Min
—
0.05
1.35
0.30
0.09
Typ
—
—
1.40
0.37
—
9.00 BSC.
7.00 BSC.
0.80 BSC.
Max
1.60
0.15
1.45
0.45
0.20
Dimension
E
E1
L
aaa
bbb
ccc
ddd
Min
0.45
θ
0°
Typ
9.00 BSC.
7.00 BSC.
0.60
0.20
0.20
0.10
0.20
3.5°
Max
0.75
7°
Notes:
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
3. This drawing conforms to the JEDEC outline MS-026, variation BBA.
4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body
Components.
Rev. 1.2
30
C8051F55x/56x/57x
Figure 4.4. QFP-32 Landing Diagram
Table 4.4. QFP-32 Landing Diagram Dimensions
Dimension
Min
Max
Dimension
Min
Max
C1
8.40
8.50
X1
0.40
0.50
C2
8.40
8.50
Y1
1.25
1.35
E
0.80 BSC
Notes:
General
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. This Land Pattern Design is based on the IPC-7351 guidelines.
Solder Mask Design
3. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the
metal pad is to be 60 μm minimum, all the way around the pad.
Stencil Design
4. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure
good solder paste release.
5. The stencil thickness should be 0.125 mm (5 mils).
6. The ratio of stencil aperture to land pad size should be 1:1 for all perimeter pads.
Card Assembly
7. A No-Clean, Type-3 solder paste is recommended.
8. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body
Components.
31
Rev. 1.2
C8051F55x/56x/57x
4.3. QFN-32 Package Specifications
Figure 4.5. QFN-32 Package Drawing
Table 4.5. QFN-32 Package Dimensions
Dimension
Min
Typ
Max
Dimension
Min
Typ
Max
A
A1
b
D
D2
e
E
0.80
0.00
0.18
0.9
0.02
0.25
5.00 BSC.
3.30
0.50 BSC.
5.00 BSC.
1.00
0.05
0.30
E2
L
L1
aaa
bbb
ddd
eee
3.20
0.30
0.00
—
—
—
—
3.30
0.40
—
—
—
—
—
3.40
0.50
0.15
0.15
0.15
0.05
0.08
3.20
3.40
Notes:
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
3. This drawing conforms to the JEDEC Solid State Outline MO-220, variation VHHD except for
custom features D2, E2, and L which are toleranced per supplier designation.
4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body
Components.
Rev. 1.2
32
C8051F55x/56x/57x
Figure 4.6. QFN-32 Landing Diagram
Table 4.6. QFN-32 Landing Diagram Dimensions
Dimension
Min
Max
Dimension
Min
Max
C1
4.80
4.90
X2
3.20
3.40
C2
4.80
4.90
Y1
0.75
0.85
Y2
3.20
3.40
e
X1
0.50 BSC
0.20
0.30
Notes:
General
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. This Land Pattern Design is based on the IPC-7351 guidelines.
Solder Mask Design
3. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the
metal pad is to be 60 μm minimum, all the way around the pad.
Stencil Design
4. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure
good solder paste release.
5. The stencil thickness should be 0.125 mm (5 mils).
6. The ratio of stencil aperture to land pad size should be 1:1 for all perimeter pads.
7. A 3x3 array of 1.0 mm openings on a 1.20 mm pitch should be used for the center ground pad.
Card Assembly
8. A No-Clean, Type-3 solder paste is recommended.
9. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body
Components.
33
Rev. 1.2
C8051F55x/56x/57x
4.4. QFN-24 Package Specifications
Figure 4.7. QFN-24 Package Drawing
Table 4.7. QFN-24 Package Dimensions
Dimension
Min
Typ
Max
Dimension
Min
Typ
Max
A
A1
b
D
D2
e
E
E2
0.70
0.00
0.18
0.75
0.02
0.25
4.00 BSC
2.70
0.50 BSC
4.00 BSC
2.70
0.80
0.05
0.30
L
L1
aaa
bbb
ddd
eee
Z
Y
0.30
0.00
0.40
0.50
0.15
0.15
0.10
0.05
0.08
2.55
2.55
2.80
2.80
0.24
0.18
Notes:
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
3. This drawing conforms to JEDEC Solid State Outline MO-220, variation WGGD, except for
custom features D2, E2, Z, Y, and L which are toleranced per supplier designation.
4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body
Components.
Rev. 1.2
34
C8051F55x/56x/57x
Figure 4.8. QFN-24 Landing Diagram
Table 4.8. QFN-24 Landing Diagram Dimensions
Dimension
Min
Max
Dimension
Min
Max
C1
3.90
4.00
X2
2.70
2.80
C2
3.90
4.00
Y1
0.65
0.75
Y2
2.70
2.80
E
X1
0.50 BSC
0.20
0.30
Notes:
General
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. This Land Pattern Design is based on the IPC-7351 guidelines.
Solder Mask Design
3. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the
metal pad is to be 60 μm minimum, all the way around the pad.
Stencil Design
4. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure
good solder paste release.
5. The stencil thickness should be 0.125 mm (5 mils).
6. The ratio of stencil aperture to land pad size should be 1:1 for all perimeter pads.
7. A 2x2 array of 1.10 mm x 1.10 mm openings on a 1.30 mm pitch should be used for the center ground
pad.
Card Assembly
8. A No-Clean, Type-3 solder paste is recommended.
9. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body
Components.
35
Rev. 1.2
C8051F55x/56x/57x
5. Electrical Characteristics
5.1. Absolute Maximum Specifications
Table 5.1. Absolute Maximum Ratings
Parameter
Conditions
Min
Typ
Max
Units
Ambient Temperature under Bias
–55
—
135
°C
Storage Temperature
–65
—
150
°C
Voltage on VREGIN with Respect to GND
–0.3
—
5.5
V
Voltage on VDD with Respect to GND
–0.3
—
2.8
V
Voltage on VDDA with Respect to GND
–0.3
—
2.8
V
Voltage on VIO with Respect to GND
–0.3
—
5.5
V
Voltage on any Port I/O Pin or RST with Respect to
GND
–0.3
—
VIO + 0.3
V
Maximum Total Current through VREGIN or GND
—
—
500
mA
Maximum Output Current Sunk by RST or any Port Pin
—
—
100
mA
Maximum Output Current Sourced by any Port Pin
—
—
100
mA
Note: Stresses outside of the range of the “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the devices at those or any other conditions
outside of those indicated in the operation listings of this specification is not implied. Exposure to maximum
rating conditions for extended periods may affect device reliability.
Rev. 1.2
36
C8051F55x/56x/57x
5.2. Electrical Characteristics
Table 5.2. Global Electrical Characteristics
–40 to +125 °C, 24 MHz system clock unless otherwise specified.
Parameter
Supply Input Voltage (VREGIN)
Min
1.8
Typ
—
Max
5.25
VRST1
—
2.75
2
—
2.75
VRST1
—
2.75
2
—
2.75
1.82
—
—
5.25
V
1.5
—
V
SYSCLK (System Clock)3
TSYSH (SYSCLK High Time)
0
—
50
MHz
9
—
—
ns
TSYSL (SYSCLK Low Time)
9
—
—
ns
Digital Supply Voltage (VDD)
Conditions
System Clock < 25 MHz
System Clock > 25 MHz
Analog Supply Voltage (VDDA) System Clock < 25 MHz
(Must be connected to VDD)
System Clock > 25 MHz
Port I/O Supply Voltage (VIO)
Normal Operation
Digital Supply RAM Data
Retention Voltage
Units
V
V
V
Specified Operating
–40
—
+125
Temperature Range
Digital Supply Current—CPU Active (Normal Mode, fetching instructions from Flash)
VDD = 2.1 V, F = 200 kHz
—
85
—
I 4
µA
VDD = 2.1 V, F = 1.5 MHz
—
660
—
µA
VDD = 2.1 V, F = 25 MHz
—
9.2
11
mA
VDD = 2.1 V, F = 50 MHz
—
17
21
mA
VDD = 2.6 V, F = 200 kHz
—
120
—
µA
VDD = 2.6 V, F = 1.5 MHz
—
920
—
µA
VDD = 2.6 V, F = 25 MHz
—
13
21
mA
VDD = 2.6 V, F = 50 MHz
—
22
33
mA
F = 25 MHz
F = 1 MHz
—
—
68
77
—
—
%/V
%/V
DD
IDD4
IDD Supply Sensitivity
4
Notes:
1. Given in Table 5.4 on page 41.
2. VIO should not be lower than the VDD voltage.
3. SYSCLK must be at least 32 kHz to enable debugging.
4. Guaranteed by characterization. Does not include oscillator supply current.
5. IDD estimation for different frequencies.
6. Idle IDD estimation for different frequencies.
37
Rev. 1.2
°C
C8051F55x/56x/57x
Table 5.2. Global Electrical Characteristics (Continued)
–40 to +125 °C, 24 MHz system clock unless otherwise specified.
Parameter
Conditions
Min
Typ
Max
VDD = 2.1 V, F < 12.5 MHz, T =
—
0.43
—
IDD Frequency Sensitivity 4,5
25 °C
—
0.33
—
VDD = 2.1 V, F > 12.5 MHz, T =
25 °C
—
0.60
—
VDD = 2.6 V, F < 12.5 MHz, T =
25 °C
—
0.42
—
VDD = 2.6 V, F > 12.5 MHz, T =
25 °C
Digital Supply Current—CPU Inactive (Idle Mode, not fetching instructions from Flash)
VDD = 2.1 V, F = 200 kHz
—
50
—
I 4
DD
IDD4
IDD Supply Sensitivity4
IDD Frequency Sensitivity 4.6
Digital Supply Current4
(Stop or Suspend Mode)
Units
mA/MHz
mA/MHz
mA/MHz
mA/MHz
µA
VDD = 2.1 V, F = 1.5 MHz
—
410
—
µA
VDD = 2.1 V, F = 25 MHz
—
6.5
8.0
mA
VDD = 2.1 V, F = 50 MHz
—
13
16
mA
VDD = 2.6 V, F = 200 kHz
—
67
—
µA
VDD = 2.6 V, F = 1.5 MHz
—
530
—
µA
VDD = 2.6 V, F = 25 MHz
—
8.0
15
mA
VDD = 2.6 V, F = 50 MHz
—
16
25
mA
F = 25 MHz
F = 1 MHz
VDD = 2.1V, F < 12.5 MHz, T = 25 °C
—
—
—
55
58
0.26
—
—
—
VDD = 2.1V, F > 12.5 MHz, T = 25 °C
—
0.26
—
VDD = 2.6V, F < 12.5 MHz, T = 25 °C
—
0.34
—
VDD = 2.6V, F > 12.5 MHz, T = 25 °C
—
0.34
—
—
—
—
1
6
70
—
—
—
%/V
mA/MHz
Oscillator not running,
VDD Monitor Disabled
Temp = 25 °C
Temp = 60 °C
Temp= 125 °C
µA
Notes:
1. Given in Table 5.4 on page 41.
2. VIO should not be lower than the VDD voltage.
3. SYSCLK must be at least 32 kHz to enable debugging.
4. Guaranteed by characterization. Does not include oscillator supply current.
5. IDD estimation for different frequencies.
6. Idle IDD estimation for different frequencies.
Rev. 1.2
38
C8051F55x/56x/57x
Figure 5.1. Minimum VDD Monitor Threshold vs. System Clock Frequency
Note: With system clock frequencies greater than 25 MHz, the VDD monitor level should be set to the high threshold
(VDMLVL = 1b in SFR VDM0CN) to prevent undefined CPU operation. The high threshold should only be used
with an external regulator powering VDD directly. See Figure 9.2 on page 80 for the recommended power
supply connections.
39
Rev. 1.2
C8051F55x/56x/57x
Table 5.3. Port I/O DC Electrical Characteristics
VDD = 1.8 to 2.75 V, –40 to +125 °C unless otherwise specified.
Parameters
Conditions
Output High Voltage IOH = –3 mA, Port I/O push-pull
IOH = –10 µA, Port I/O push-pull
IOH = –10 mA, Port I/O push-pull
Output Low Voltage VIO = 1.8 V:
IOL = 70 µA
IOL = 8.5 mA
VIO = 2.7 V:
IOL = 70 µA
IOL = 8.5 mA
VIO = 5.25 V:
IOL = 70 µA
IOL = 8.5 mA
VREGIN = 5.25 V
Input High Voltage
VREGIN = 2.7 V
Input Low Voltage
Weak Pullup Off
Weak Pullup On, VIO = 2.1 V,
VIN = 0 V, VDD = 1.8 V
Input Leakage
Current
Min
VIO – 0.4
VIO – 0.02
—
Typ
—
—
VIO – 0.7
Max
—
—
—
—
—
—
—
50
750
—
—
—
—
45
550
—
—
0.7 x VIO
—
—
—
—
—
—
—
40
400
0.3 x VIO
±2
—
7
9
Units
V
mV
V
V
µA
Weak Pullup On, VIO = 2.6 V,
VIN = 0 V, VDD = 2.6 V
—
17
22
Weak Pullup On, VIO = 5.0 V,
VIN = 0 V, VDD = 2.6 V
—
49
115
Rev. 1.2
40
C8051F55x/56x/57x
Table 5.4. Reset Electrical Characteristics
–40 to +125 °C unless otherwise specified.
Parameter
Conditions
Min
Typ
Max
Units
—
—
40
mV
RST Input High Voltage
0.7 x VIO
—
—
RST Input Low Voltage
—
—
0.3 x VIO
—
49
115
µA
VDD RST Threshold (VRST-LOW)
1.65
1.75
1.80
V
VDD RST Threshold (VRST-HIGH)
2.25
2.30
2.45
V
—
—
1
ms
VDD = 2.1 V
200
340
600
VDD = 2.5 V
200
250
600
—
155
175
µs
Minimum RST Low Time to
Generate a System Reset
6
—
—
µs
VDD Monitor Turn-on Time
—
60
100
µs
VDD Monitor Supply Current
—
1
2
µA
RST Output Low Voltage
RST Input Pullup Current
VIO = 5 V; IOL = 70 µA
RST = 0.0 V, VIO = 5 V
VREGIN Ramp Time for Power On VREGIN Ramp 0–1.8 V
Time from last system clock
rising edge to reset initiation
Missing Clock Detector Timeout
Delay between release of
any reset source and code
execution at location 0x0000
Reset Time Delay
µs
Table 5.5. Flash Electrical Characteristics
VDD = 1.8 to 2.75 V, –40 to +125 °C unless otherwise specified.
Parameter
Flash Size
Endurance
Retention
Erase Cycle Time
Write Cycle Time
VDD
Temperature during
Programming Operations
Conditions
C8051F550-3, ‘F560-3,
‘F568-9, and ‘F570-1
C8051F554-7, ‘F564-7, and
‘F572-5
Min
Typ
Max
327681
Bytes
16384
125 °C
25 MHz System Clock
25 MHz System Clock
20 k
10
28
79
150 k
—
30
84
—
—
45
125
Erase/Write
Years
ms
µs
Write/Erase operations
VRST-HIGH2
—
—
V
0
–40
—
—
+125
+125
°C
–I Devices
–A Devices
1. On the 32 kB Flash devices, 1024 bytes at addresses 0x7C00 to 0x7FFF are reserved.
2. See Table 5.4 for the VRST-HIGH specification.
41
Units
Rev. 1.2
C8051F55x/56x/57x
Table 5.6. Internal High-Frequency Oscillator Electrical Characteristics
VDD = 1.8 to 2.75 V, –40 to +125 °C unless otherwise specified; Using factory-calibrated settings.
Parameter
Conditions
Oscillator Frequency
Min
Typ
Max
Units
IFCN = 111b;
VDD > VREGMIN1
24 – 0.5%
242
24 + 0.5%
MHz
IFCN = 111b;
VDD < VREGMIN1
24 – 1.0%
242
24 + 1.0%
Oscillator Supply Current
(from VDD)
Internal Oscillator On
OSCICN[7:6] = 11b
—
880
1300
Internal Oscillator Suspend
OSCICN[7:6] = 00b
ZTCEN = 1
Temp = 25 °C
Temp = 85 °C
Temp = 125 °C
—
67
90
130
—
Wake-up Time From Suspend
OSCICN[7:6] = 00b
—
1
—
µs
Power Supply Sensitivity
Constant Temperature
—
0.11
—
%/V
Temperature Sensitivity3
Constant Supply
TC1
TC2
—
—
5.0
–0.65
—
—
ppm/°C
ppm/°C2
µA
1. VREGMIN is the minimum output of the voltage regulator for its low setting (REG0CN: REG0MD = 0b). See
Table 5.8, “Voltage Regulator Electrical Characteristics,” on page 43.
2. This is the average frequency across the operating temperature range
3. Use temperature coefficients TC1 and TC2 to calculate the new internal oscillator frequency using the
following equation:
f(T) = f0 x (1 + TC1 x (T - T0) + TC2 x (T - T0)2)
where f0 is the internal oscillator frequency at 25 °C and T0 is 25 °C.
Rev. 1.2
42
C8051F55x/56x/57x
Table 5.7. Clock Multiplier Electrical Specifications
VDD = 1.8 to 2.75 V, –40 to +125 °C unless otherwise specified.
Parameter
Input Frequency (Fcmin)
Output Frequency
Power Supply Current
Conditions
Min
2
—
—
Typ
—
—
0.9
Max
—
50
1.9
Units
MHz
MHz
mA
Min
1.8*
—
2.0
Typ
—
10
2.1
Max
5.25
—
2.25
Units
V
mV/mA
2.5
—
2.6
1
2.75
9
µA
–0.21
—
–0.02
V
—
0.29
—
mV/°C
—
450
—
µs
Table 5.8. Voltage Regulator Electrical Characteristics
VDD = 1.8 to 2.75 V, –40 to +125 °C unless otherwise specified.
Parameter
Conditions
Input Voltage Range (VREGIN)
Dropout Voltage (VDO)
Maximum Current = 50 mA
2.1 V operation (REG0MD = 0)
Output Voltage (VDD)
2.6 V operation (REG0MD = 1)
Bias Current
Dropout Indicator Detection
With respect to VDD
Threshold
Output Voltage Temperature
Coefficient
50 mA load with VREGIN = 2.4 V
VREG Settling Time
and VDD load capacitor of 4.8 µF
*Note: The minimum input voltage is 1.8 V or VDD + VDO(max load), whichever is greater
43
Rev. 1.2
V
C8051F55x/56x/57x
Table 5.9. ADC0 Electrical Characteristics
VDDA = 1.8 to 2.75 V, –40 to +125 °C, VREF = 1.5 V (REFSL=0) unless otherwise specified.
Parameter
Conditions
Min
Typ
Max
Units
—
—
–10
12
±0.5
±0.5
3.0
±3
±1
10
bits
LSB
LSB
LSB
–20
—
5.7
7.7
20
—
LSB
ppm/°C
DC Accuracy
Resolution
Integral Nonlinearity
Differential Nonlinearity
Guaranteed Monotonic
1
Offset Error
Full Scale Error
Offset Temperature Coefficient
Dynamic performance (10 kHz sine-wave single-ended input, 1 dB below Full Scale, 200 ksps)
Signal-to-Noise Plus Distortion
Total Harmonic Distortion
Spurious-Free Dynamic Range
Up to the 5th harmonic;
63
—
—
65
80
-82
—
—
—
dB
dB
dB
—
13
—
—
3.6
—
MHz
clocks
1.5
3.5
—
—
—
—
—
—
200
µs
0
0
0
—
V
—
VREF
VREF / n
VIO
—
—
31
3
—
—
pF
kΩ
—
1100
1500
µA
—
5
—
1100
—
–60
1500
—
—
µA
µs
mV/V
Conversion Rate
SAR Conversion Clock
Conversion Time in SAR Clocks
2
Track/Hold Acquisition Time3
Throughput Rate4
VDDA > 2.0 V
VDDA < 2.0 V
VDDA > 2.0 V
ksps
Analog Inputs
ADC Input Voltage Range5
gain = 1.0 (default)
gain = n
Absolute Pin Voltage with respect
to GND
Sampling Capacitance
Input Multiplexer Impedance
V
Power Specifications
Power Supply Current
(VDDA supplied to ADC0)
Burst Mode (Idle)
Power-On Time
Power Supply Rejection
Operating Mode, 200 ksps
Notes:
1. Represents one standard deviation from the mean. Offset and full-scale error can be removed through
calibration.
2. An additional 2 FCLK cycles are required to start and complete a conversion
3. Additional tracking time may be required depending on the output impedance connected to the ADC input.
See Section “6.2.1. Settling Time Requirements” on page 52.
4. An increase in tracking time will decrease the ADC throughput.
5. See Section “6.3. Selectable Gain” on page 53 for more information about the setting the gain.
Rev. 1.2
44
C8051F55x/56x/57x
Table 5.10. Temperature Sensor Electrical Characteristics
VDDA = 1.8 to 2.75 V, –40 to +125 °C unless otherwise specified.
Parameter
Conditions
Min
Typ
Max
Units
Linearity
—
±0.1
—
°C
Slope
—
3.33
—
mV/°C
Slope Error*
—
88
—
µV/°C
Offset
Temp = 0 °C
—
856
—
mV
Offset Error*
Temp = 0 °C
—
±14
—
mV
Power Supply Current
—
18
—
µA
Tracking Time
12
—
—
µs
*Note: Represents one standard deviation from the mean.
Table 5.11. Voltage Reference Electrical Characteristics
VDDA = 1.8 to 2.75 V, –40 to +125 °C unless otherwise specified.
Parameter
Conditions
Min
Typ
Max
Units
25 °C ambient (REFLV = 0)
1.45
1.50
1.55
25 °C ambient (REFLV = 1), VDD = 2.6 V
2.15
2.20
2.25
VREF Short-Circuit Current
—
5
10
mA
VREF Temperature
Coefficient
—
38
—
ppm/°C
Internal Reference (REFBE = 1)
Output Voltage
V
Power Consumption
Internal
—
30
50
µA
Load Regulation
Load = 0 to 200 µA to AGND
—
3
—
µV/µA
VREF Turn-on Time 1
4.7 µF tantalum and 0.1 µF bypass
—
1.5
—
ms
VREF Turn-on Time 2
0.1 µF bypass
—
46
—
µs
—
1.2
—
mV/V
1.5
—
VDDA
V
Sample Rate = 200 ksps; VREF = 1.5 V
—
2.1
—
µA
REFBE = 1 or TEMPE = 1
—
21
40
µA
Power Supply Rejection
External Reference (REFBE = 0)
Input Voltage Range
Input Current
Power Specifications
Reference Bias Generator
45
Rev. 1.2
C8051F55x/56x/57x
Table 5.12. Comparator 0 and Comparator 1 Electrical Characteristics
VIO = 1.8 to 5.25 V, –40 to +125 °C unless otherwise noted.
Parameter
Conditions
Min
Typ
Max
Units
Response Time:
Mode 0, Vcm* = 1.5 V
CPn+ – CPn– = 100 mV
—
330
—
ns
CPn+ – CPn– = –100 mV
—
390
—
ns
Response Time:
Mode 1, Vcm* = 1.5 V
CPn+ – CPn– = 100 mV
—
490
—
ns
CPn+ – CPn– = –100 mV
—
610
—
ns
Response Time:
Mode 2, Vcm* = 1.5 V
CPn+ – CPn– = 100 mV
—
590
—
ns
CP0+ – CP0– = –100 mV
—
750
—
ns
Response Time:
Mode 3, Vcm* = 1.5 V
CPn+ – CPn– = 100 mV
—
2300
—
ns
CPn+ – CPn– = –100 mV
—
3100
—
ns
—
2.1
13
mV/V
Common-Mode Rejection Ratio
Positive Hysteresis 1
CPnHYP1–0 = 00
-2
0
2
mV
Positive Hysteresis 2
CPnHYP1–0 = 01
2
6
10
mV
Positive Hysteresis 3
CPnHYP1–0 = 10
5
11
20
mV
Positive Hysteresis 4
CPnHYP1–0 = 11
13
21
40
mV
Negative Hysteresis 1
CPnHYN1–0 = 00
-2
0
2
mV
Negative Hysteresis 2
CPnHYN1–0 = 01
2
5
10
mV
Negative Hysteresis 3
CPnHYN1–0 = 10
5
11
20
mV
Negative Hysteresis 4
CPnHYN1–0 = 11
13
21
40
mV
–0.25
—
VIO + 0.25
V
—
8
—
pF
–10
—
+10
mV
Power Supply Rejection
—
0.18
—
mV/V
Power-up Time
—
3
—
µs
Mode 0
—
6.3
20
µA
Mode 1
—
3.4
10
µA
Mode 2
—
2.6
7.5
µA
Mode 3
—
0.6
3
µA
Inverting or Non-Inverting Input
Voltage Range
Input Capacitance
Input Offset Voltage
Power Supply
Supply Current at DC
*Note: Vcm is the common-mode voltage on CP0+ and CP0–.
Rev. 1.2
46
C8051F55x/56x/57x
6. 12-Bit ADC (ADC0)
ADC0TK
ADC0CN
AD0PWR3
AD0PWR2
AD0PWR1
AD0PWR0
AD0TM1
AD0TM0
AD0TK1
AD0TK0
AD0EN
BURSTEN
AD0INT
AD0BUSY
AD0WINT
AD0LJST
AD0CM1
AD0CM0
The ADC0 on the C8051F55x/56x/57x consists of an analog multiplexer (AMUX0) with 33, 25, or 18 total
input selections and a 200 ksps, 12-bit successive-approximation-register (SAR) ADC with integrated
track-and-hold, programmable window detector, programmable attenuation (1:2), and hardware accumulator. The ADC0 subsystem has a special Burst Mode which can automatically enable ADC0, capture and
accumulate samples, then place ADC0 in a low power shutdown mode without CPU intervention. The
AMUX0, data conversion modes, and window detector are all configurable under software control via the
Special Function Registers shows in Figure 6.1. ADC0 inputs are single-ended and may be configured to
measure P0.0-P3.7, the Temperature Sensor output, VDD, or GND with respect to GND. The voltage reference for ADC0 is selected as described in Section “6.6. Temperature Sensor” on page 67. ADC0 is
enabled when the AD0EN bit in the ADC0 Control register (ADC0CN) is set to logic 1, or when performing
conversions in Burst Mode. ADC0 is in low power shutdown when AD0EN is logic 0 and no Burst Mode
conversions are taking place.
ADC0MX4
ADC0MX3
ADC0MX2
ADC0MX1
ADC0MX0
ADC0MX
P2.2-P2.7, P3.0 available
on 40-pin and 32-pin
packages
P3.1-P3.7 available on 40pin packages
Start
Conversion
P1.7
P2.0
12-Bit
SAR
Selectable
Gain
ADC
35-to-1
AMUX0
P2.7
P3.0
ADC0GNH ADC0GNL ADC0GNA
AD0BUSY (W)
01
Timer 1 Overflow
10
CNVSTR Input
11
Timer 2 Overflow
ADC0L
Burst Mode
Oscillator
25 MHz Max
Burst Mode
Logic
00
Accumulator
AD0TM1:0
AD0PRE
AD0POST
FCLK
REF
P0.7
P1.0
Start
Conversion
ADC0H
SYSCLK
VDD
FCLK
P0.0
AD0WINT
VDD
Temp Sensor
GND
AD0SC4
AD0SC3
AD0SC2
AD0SC1
AD0SC0
AD0RPT1
AD0RPT0
GAINEN
P3.7
ADC0LTH ADC0LTL
ADC0CF
ADC0GTH ADC0GTL
32
Window
Compare
Logic
Figure 6.1. ADC0 Functional Block Diagram
Rev. 1.2
47
C8051F55x/56x/57x
6.1. Modes of Operation
In a typical system, ADC0 is configured using the following steps:
1. If a gain adjustment is required, refer to Section “6.3. Selectable Gain” on page 53.
2. Choose the start of conversion source.
3. Choose Normal Mode or Burst Mode operation.
4. If Burst Mode, choose the ADC0 Idle Power State and set the Power-up Time.
5. Choose the tracking mode. Note that Pre-Tracking Mode can only be used with Normal Mode.
6. Calculate the required settling time and set the post convert-start tracking time using the AD0TK bits.
7. Choose the repeat count.
8. Choose the output word justification (Right-Justified or Left-Justified).
9. Enable or disable the End of Conversion and Window Comparator Interrupts.
6.1.1. Starting a Conversion
A conversion can be initiated in one of four ways, depending on the programmed states of the ADC0 Start
of Conversion Mode bits (AD0CM1–0) in register ADC0CN. Conversions may be initiated by one of the following:
Writing a 1 to the AD0BUSY bit of register ADC0CN
A rising edge on the CNVSTR input signal (pin P0.1)
A Timer 1 overflow (i.e., timed continuous conversions)
A Timer 2 overflow (i.e., timed continuous conversions)
Writing a 1 to AD0BUSY provides software control of ADC0 whereby conversions are performed "ondemand.” During conversion, the AD0BUSY bit is set to logic 1 and reset to logic 0 when the conversion is
complete. The falling edge of AD0BUSY triggers an interrupt (when enabled) and sets the ADC0 interrupt
flag (AD0INT). Note: When polling for ADC conversion completions, the ADC0 interrupt flag (AD0INT)
should be used. Converted data is available in the ADC0 data registers, ADC0H:ADC0L, when bit AD0INT
is logic 1. Note that when Timer 2 overflows are used as the conversion source, Low Byte overflows are
used if Timer2 is in 8-bit mode; High byte overflows are used if Timer 2 is in 16-bit mode. See Section
“25. Timers” on page 259 for timer configuration.
Important Note About Using CNVSTR: The CNVSTR input pin also functions as Port pin P0.1. When the
CNVSTR input is used as the ADC0 conversion source, Port pin P0.1 should be skipped by the Digital
Crossbar. To configure the Crossbar to skip P0.1, set to 1 Bit1 in register P0SKIP. See Section “19. Port
Input/Output” on page 169 for details on Port I/O configuration.
6.1.2. Tracking Modes
Each ADC0 conversion must be preceded by a minimum tracking time for the converted result to be accurate. ADC0 has three tracking modes: Pre-Tracking, Post-Tracking, and Dual-Tracking. Pre-Tracking Mode
provides the minimum delay between the convert start signal and end of conversion by tracking continuously before the convert start signal. This mode requires software management in order to meet minimum
tracking requirements. In Post-Tracking Mode, a programmable tracking time starts after the convert start
signal and is managed by hardware. Dual-Tracking Mode maximizes tracking time by tracking before and
after the convert start signal. Figure 6.2 shows examples of the three tracking modes.
Pre-Tracking Mode is selected when AD0TM is set to 10b. Conversions are started immediately following
the convert start signal. ADC0 is tracking continuously when not performing a conversion. Software must
allow at least the minimum tracking time between each end of conversion and the next convert start signal.
The minimum tracking time must also be met prior to the first convert start signal after ADC0 is enabled.
48
Rev. 1.2
C8051F55x/56x/57x
Post-Tracking Mode is selected when AD0TM is set to 01b. A programmable tracking time based on
AD0TK is started immediately following the convert start signal. Conversions are started after the programmed tracking time ends. After a conversion is complete, ADC0 does not track the input. Rather, the
sampling capacitor remains disconnected from the input making the input pin high-impedance until the
next convert start signal.
Dual-Tracking Mode is selected when AD0TM is set to 11b. A programmable tracking time based on
AD0TK is started immediately following the convert start signal. Conversions are started after the programmed tracking time ends. After a conversion is complete, ADC0 tracks continuously until the next conversion is started.
Depending on the output connected to the ADC input, additional tracking time, more than is specified in
Table 5.9, may be required after changing MUX settings. See the settling time requirements described in
Section “6.2.1. Settling Time Requirements” on page 52.
Convert Start
Pre-Tracking
AD0TM = 10
Track
Post-Tracking
AD0TM= 01
Idle
Track
Convert
Idle
Track
Convert..
Dual-Tracking
AD0TM = 11
Track
Track
Convert
Track
Track
Convert..
Convert
Track
Convert ...
Figure 6.2. ADC0 Tracking Modes
6.1.3. Timing
ADC0 has a maximum conversion speed specified in Table 5.9. ADC0 is clocked from the ADC0 Subsystem Clock (FCLK). The source of FCLK is selected based on the BURSTEN bit. When BURSTEN is
logic 0, FCLK is derived from the current system clock. When BURSTEN is logic 1, FCLK is derived from
the Burst Mode Oscillator, an independent clock source with a maximum frequency of 25 MHz.
When ADC0 is performing a conversion, it requires a clock source that is typically slower than FCLK. The
ADC0 SAR conversion clock (SAR clock) is a divided version of FCLK. The divide ratio can be configured
using the AD0SC bits in the ADC0CF register. The maximum SAR clock frequency is listed in Table 5.9.
ADC0 can be in one of three states at any given time: tracking, converting, or idle. Tracking time depends
on the tracking mode selected. For Pre-Tracking Mode, tracking is managed by software and ADC0 starts
conversions immediately following the convert start signal. For Post-Tracking and Dual-Tracking Modes,
the tracking time after the convert start signal is equal to the value determined by the AD0TK bits plus 2
FCLK cycles. Tracking is immediately followed by a conversion. The ADC0 conversion time is always 13
SAR clock cycles plus an additional 2 FCLK cycles to start and complete a conversion. Figure 6.3 shows
timing diagrams for a conversion in Pre-Tracking Mode and tracking plus conversion in Post-Tracking or
Dual-Tracking Mode. In this example, repeat count is set to one.
Rev. 1.2
49
C8051F55x/56x/57x
Convert Start
Pre-Tracking Mode
Time
F
S1
S2
ADC0 State
...
S12
S13
F
Convert
AD0INT Flag
Post-Tracking or Dual-Tracking Modes (AD0TK = ‘00')
Time
F
S1
ADC0 State
S2
F F
S1
Track
...
S2
S12
S13
F
Convert
AD0INT Flag
Key
F
Sn
Equal to one period of FCLK.
Each Sn is equal to one period of the SAR clock.
Figure 6.3. 12-Bit ADC Tracking Mode Example
6.1.4. Burst Mode
Burst Mode is a power saving feature that allows ADC0 to remain in a very low power state between conversions. When Burst Mode is enabled, ADC0 wakes from a very low power state, accumulates 1, 4, 8, or
16 samples using an internal Burst Mode clock (approximately 25 MHz), then re-enters a very low power
state. Since the Burst Mode clock is independent of the system clock, ADC0 can perform multiple conversions then enter a very low power state within a single system clock cycle, even if the system clock is slow
(e.g., 32.768 kHz), or suspended.
Burst Mode is enabled by setting BURSTEN to logic 1. When in Burst Mode, AD0EN controls the ADC0
idle power state (i.e. the state ADC0 enters when not tracking or performing conversions). If AD0EN is set
to logic 0, ADC0 is powered down after each burst. If AD0EN is set to logic 1, ADC0 remains enabled after
each burst. On each convert start signal, ADC0 is awakened from its Idle Power State. If ADC0 is powered
down, it will automatically power up and wait the programmable Power-up Time controlled by the AD0PWR
bits. Otherwise, ADC0 will start tracking and converting immediately. Figure 6.4 shows an example of Burst
Mode Operation with a slow system clock and a repeat count of 4.
Important Note: When Burst Mode is enabled, only Post-Tracking and Dual-Tracking modes can be used.
When Burst Mode is enabled, a single convert start will initiate a number of conversions equal to the repeat
count. When Burst Mode is disabled, a convert start is required to initiate each conversion. In both modes,
the ADC0 End of Conversion Interrupt Flag (AD0INT) will be set after “repeat count” conversions have
50
Rev. 1.2
C8051F55x/56x/57x
been accumulated. Similarly, the Window Comparator will not compare the result to the greater-than and
less-than registers until “repeat count” conversions have been accumulated.
Note: When using Burst Mode, care must be taken to issue a convert start signal no faster than once every four
SYSCLK periods. This includes external convert start signals.
System Clock
Convert Start
(AD0BUSY or Timer
Overflow)
Post-Tracking
AD0TM = 01
AD0EN = 0
Powered
Down
Power-Up
and Idle
T C T C T C T C
Powered
Down
Power-Up
and Idle
T C..
Dual-Tracking
AD0TM = 11
AD0EN = 0
Powered
Down
Power-Up
and Track
T C T C T C T C
Powered
Down
Power-Up
and Track
T C..
AD0PWR
Post-Tracking
AD0TM = 01
AD0EN = 1
Idle
T C T C T C T C
Idle
T C T C T C..
Dual-Tracking
AD0TM = 11
AD0EN = 1
Track
T C T C T C T C
Track
T C T C T C..
T = Tracking
C = Converting
Convert Start
(CNVSTR)
Post-Tracking
AD0TM = 01
AD0EN = 0
Powered
Down
Power-Up
and Idle
T C
Powered
Down
Power-Up
and Idle
T C..
Dual-Tracking
AD0TM = 11
AD0EN = 0
Powered
Down
Power-Up
and Track
T C
Powered
Down
Power-Up
and Track
T C..
AD0PWR
Post-Tracking
AD0TM = 01
AD0EN = 1
Idle
T C
Idle
T C
Idle..
Dual-Tracking
AD0TM = 11
AD0EN = 1
Track
T C
Track
T C
Track..
T = Tracking
C = Converting
Figure 6.4. 12-Bit ADC Burst Mode Example With Repeat Count Set to 4
Rev. 1.2
51
C8051F55x/56x/57x
6.2. Output Code Formatting
The registers ADC0H and ADC0L contain the high and low bytes of the output conversion code. When the
repeat count is set to 1, conversion codes are represented in 12-bit unsigned integer format and the output
conversion code is updated after each conversion. Inputs are measured from 0 to VREF x 4095/4096. Data
can be right-justified or left-justified, depending on the setting of the AD0LJST bit (ADC0CN.2). Unused
bits in the ADC0H and ADC0L registers are set to 0. Example codes are shown below for both right-justified and left-justified data.
Input Voltage
Right-Justified ADC0H:ADC0L
(AD0LJST = 0)
Left-Justified ADC0H:ADC0L
(AD0LJST = 1)
VREF x 4095/4096
VREF x 2048/4096
VREF x 2047/4096
0
0x0FFF
0x0800
0x07FF
0x0000
0xFFF0
0x8000
0x7FF0
0x0000
When the ADC0 Repeat Count is greater than 1, the output conversion code represents the accumulated
result of the conversions performed and is updated after the last conversion in the series is finished. Sets
of 4, 8, or 16 consecutive samples can be accumulated and represented in unsigned integer format. The
repeat count can be selected using the AD0RPT bits in the ADC0CF register. The value must be right-justified (AD0LJST = 0), and unused bits in the ADC0H and ADC0L registers are set to 0. The following
example shows right-justified codes for repeat counts greater than 1. Notice that accumulating 2n samples
is equivalent to left-shifting by n bit positions when all samples returned from the ADC have the same
value.
Input Voltage
Repeat Count = 4
Repeat Count = 8
Repeat Count = 16
VREF x 4095/4096
VREF x 2048/4096
VREF x 2047/4096
0
0x3FFC
0x2000
0x1FFC
0x0000
0x7FF8
0x4000
0x3FF8
0x0000
0xFFF0
0x8000
0x7FF0
0x0000
6.2.1. Settling Time Requirements
A minimum tracking time is required before an accurate conversion is performed. This tracking time is
determined by any series impedance, including the AMUX0 resistance, the ADC0 sampling capacitance,
and the accuracy required for the conversion.
Figure 6.5 shows the equivalent ADC0 input circuit. The required ADC0 settling time for a given settling
accuracy (SA) may be approximated by Equation 6.1. When measuring the Temperature Sensor output,
use the settling time specified in Table 5.10. When measuring VDD with respect to GND, RTOTAL reduces to
RMUX. See Table 5.9 for ADC0 minimum settling time requirements as well as the mux impedance and
sampling capacitor values.
n
2
t = ln -------- × R TOTAL C SAMPLE
SA
Equation 6.1. ADC0 Settling Time Requirements
Where:
SA is the settling accuracy, given as a fraction of an LSB (for example, 0.25 to settle within 1/4 LSB).
t is the required settling time in seconds. RTOTAL is the sum of the AMUX0 resistance and any external
source resistance. n is the ADC resolution in bits (10).
52
Rev. 1.2
C8051F55x/56x/57x
M U X S e le c t
P x .x
R MUX
C SAM P LE
R C In p u t = R M U X * C S A M P L E
Figure 6.5. ADC0 Equivalent Input Circuit
6.3. Selectable Gain
ADC0 on the C8051F55x/56x/57x family of devices implements a selectable gain adjustment option. By
writing a value to the gain adjust address range, the user can select gain values between 0 and 1.016.
For example, three analog sources to be measured have full-scale outputs of 5.0 V, 4.0 V, and 3.0 V,
respectively. Each ADC measurement would ideally use the full dynamic range of the ADC with an internal
voltage reference of 1.5 V or 2.2 V (set to 2.2 V for this example). When selecting the first source (5.0 V
full-scale), a gain value of 0.44 (5 V full scale x 0.44 = 2.2 V full scale) provides a full-scale signal of 2.2 V
when the input signal is 5.0 V. Likewise, a gain value of 0.55 (4 V full scale x 0.55 = 2.2 V full scale) for the
second source and 0.73 (3 V full scale x 0.73 = 2.2 V full scale) for the third source provide full-scale ADC0
measurements when the input signal is full-scale.
Additionally, some sensors or other input sources have small part-to-part variations that must be
accounted for to achieve accurate results. In this case, the programmable gain value could be used as a
calibration value to eliminate these part-to-part variations.
6.3.1. Calculating the Gain Value
The ADC0 selectable gain feature is controlled by 13 bits in three registers. ADC0GNH contains the 8
upper bits of the gain value and ADC0GNL contains the 4 lower bits of the gain value. The final GAINADD
bit (ADC0GNA.0) controls an optional extra 1/64 (0.016) of gain that can be added in addition to the
ADC0GNH and ADC0GNL gain. The ADC0GNA.0 bit is set to 1 after a power-on reset.
The equivalent gain for the ADC0GNH, ADC0GNL and ADC0GNA registers is as follows:
GAIN
1
gain = --------------- + GAINADD × ------
4096
64
Equation 6.2. Equivalent Gain from the ADC0GNH and ADC0GNL Registers
Where:
GAIN is the 12-bit word of ADC0GNH[7:0] and ADC0GNL[7:4]
GAINADD is the value of the GAINADD bit (ADC0GNA.0)
gain is the equivalent gain value from 0 to 1.016
Rev. 1.2
53
C8051F55x/56x/57x
For example, if ADC0GNH = 0xFC, ADC0GNL = 0x00, and GAINADD = 1, GAIN = 0xFC0 = 4032, and the
resulting equation is as follows:
4032
1
GAIN = ------------- + 1 × ------ = 0.984 + 0.016 = 1.0
4096
64
The table below equates values in the ADC0GNH, ADC0GNL, and ADC0GNA registers to the equivalent
gain using this equation.
ADC0GNH Value
ADC0GNL Value
GAINADD Value
GAIN Value
Equivalent Gain
0xFC (default)
0x7C
0xBC
0x3C
0xFF
0xFF
0x00 (default)
0x00
0x00
0x00
0xF0
0xF0
1 (default)
1
1
1
0
1
4032 + 64
1984 + 64
3008 + 64
960 + 64
4095 + 0
4096 + 64
1.0 (default)
0.5
0.75
0.25
~1.0
1.016
For any desired gain value, the GAIN registers can be calculated by the following:
1
GAIN = gain – GAINADD × ------ × 4096
64
Equation 6.3. Calculating the ADC0GNH and ADC0GNL Values from the Desired Gain
Where:
GAIN is the 12-bit word of ADC0GNH[7:0] and ADC0GNL[7:4]
GAINADD is the value of the GAINADD bit (ADC0GNA.0)
gain is the equivalent gain value from 0 to 1.016
When calculating the value of GAIN to load into the ADC0GNH and ADC0GNL registers, the GAINADD bit
can be turned on or off to reach a value closer to the desired gain value.
For example, the initial example in this section requires a gain of 0.44 to convert 5 V full scale to 2.2 V full
scale. Using Equation 6.3:
1
GAIN = 0.44 – GAINADD × ------ × 4096
64
If GAINADD is set to 1, this makes the equation:
1
GAIN = 0.44 – 1 × ------ × 4096 = 0.424 × 4096 = 1738 = 0x06CA
64
The actual gain from setting GAINADD to 1 and ADC0GNH and ADC0GNL to 0x6CA is 0.4399. A similar
gain can be achieved if GAINADD is set to 0 with a different value for ADC0GNH and ADC0GNL.
54
Rev. 1.2
C8051F55x/56x/57x
6.3.2. Setting the Gain Value
The three programmable gain registers are accessed indirectly using the ADC0H and ADC0L registers
when the GAINEN bit (ADC0CF.0) bit is set. ADC0H acts as the address register, and ADC0L is the data
register. The programmable gain registers can only be written to and cannot be read. See Gain Register
Definition 6.1, Gain Register Definition 6.2, and Gain Register Definition 6.3 for more information.
The gain is programmed using the following steps:
1. Set the GAINEN bit (ADC0CF.0)
2. Load the ADC0H with the ADC0GNH, ADC0GNL, or ADC0GNA address.
3. Load ADC0L with the desired value for the selected gain register.
4. Reset the GAINEN bit (ADC0CF.0)
Notes:
1. An ADC conversion should not be performed while the GAINEN bit is set.
2. Even with gain enabled, the maximum input voltage must be less than VREGIN and the maximum
voltage of the signal after gain must be less than or equal to VREF.
In code, changing the value to 0.44 gain from the previous example looks like:
// in ‘C’:
ADC0CF |= 0x01;
ADC0H = 0x04;
ADC0L = 0x6C;
ADC0H = 0x07;
ADC0L = 0xA0;
ADC0H = 0x08;
ADC0L = 0x01;
ADC0CF &= ~0x01;
// GAINEN = 1
// Load the ADC0GNH address
// Load the upper byte of 0x6CA to ADC0GNH
// Load the ADC0GNL address
// Load the lower nibble of 0x6CA to ADC0GNL
// Load the ADC0GNA address
// Set the GAINADD bit
// GAINEN = 0
; in assembly
ORL ADC0CF,#01H
MOV ADC0H,#04H
MOV ADC0L,#06CH
MOV ADC0H,#07H
MOV ADC0L,#0A0H
MOV ADC0H,#08H
MOV ADC0L,#01H
ANL ADC0CF,#0FEH
; GAINEN = 1
; Load the ADC0GNH address
; Load the upper byte of 0x6CA to ADC0GNH
; Load the ADC0GNL address
; Load the lower nibble of 0x6CA to ADC0GNL
; Load the ADC0GNA address
; Set the GAINADD bit
; GAINEN = 0
Rev. 1.2
55
C8051F55x/56x/57x
Gain Register Definition 6.1. ADC0GNH: ADC0 Selectable Gain High Byte
Bit
7
6
5
4
3
Name
GAINH[7:0]
Type
W
Reset
1
1
1
1
Indirect Address = 0x04;
Bit
Name
7:0
1
2
1
0
1
0
0
Function
GAINH[7:0] ADC0 Gain High Byte.
See Section 6.3.1 for details on calculating the value for this register.
Note: This register is accessed indirectly; See Section 6.3.2 for details for writing this register.
Gain Register Definition 6.2. ADC0GNL: ADC0 Selectable Gain Low Byte
Bit
7
6
5
4
3
2
1
0
Name
GAINL[3:0]
Reserved
Reserved
Reserved
Reserved
Type
W
W
W
W
W
0
0
0
0
Reset
0
0
0
0
Indirect Address = 0x07;
Bit
Name
7:4
Function
GAINL[3:0] ADC0 Gain Lower 4 Bits.
See Figure 6.3.1 for details for setting this register.
This register is only accessed indirectly through the ADC0H and ADC0L register.
3:0
Reserved
Must Write 0000b
Note: This register is accessed indirectly; See Section 6.3.2 for details for writing this register.
56
Rev. 1.2
C8051F55x/56x/57x
Gain Register Definition 6.3. ADC0GNA: ADC0 Additional Selectable Gain
Bit
7
6
5
4
3
2
Name
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Type
W
W
W
W
W
W
W
W
Reset
0
0
0
0
0
0
0
1
Indirect Address = 0x08;
Bit
Name
1
0
Reserved GAINADD
Function
7:1
Reserved
Must Write 0000000b.
0
GAINADD
ADC0 Additional Gain Bit.
Setting this bit add 1/64 (0.016) gain to the gain value in the ADC0GNH and
ADC0GNL registers.
Note: This register is accessed indirectly; See Section 6.3.2 for details for writing this register.
Rev. 1.2
57
C8051F55x/56x/57x
SFR Definition 6.4. ADC0CF: ADC0 Configuration
Bit
7
6
5
Name
AD0SC[4:0]
Type
R/W
Reset
1
1
1
4
2
1
AD0RPT[1:0]
1
SFR Address = 0xBC; SFR Page = 0x00
Bit
Name
7:3
3
1
0
GAINEN
R/W
R/W
R/W
0
0
0
Function
AD0SC[4:0] ADC0 SAR Conversion Clock Period Bits.
SAR Conversion clock is derived from system clock by the following equation, where
AD0SC refers to the 5-bit value held in bits AD0SC4–0. SAR Conversion clock
requirements are given in the ADC specification table
BURSTEN = 0: FCLK is the current system clock
BURSTEN = 1: FCLK is a maximum of 30 MHz, independent of the current system
clock..
FCLK
AD0SC = -------------------- – 1
CLK SAR
Note: Round up the result of the calculation for AD0SC
2:1
A0RPT[1:0] ADC0 Repeat Count.
Controls the number of conversions taken and accumulated between ADC0 End of
Conversion (ADCINT) and ADC0 Window Comparator (ADCWINT) interrupts. A convert start is required for each conversion unless Burst Mode is enabled. In Burst
Mode, a single convert start can initiate multiple self-timed conversions. Results in
both modes are accumulated in the ADC0H:ADC0L register. When AD0RPT1–0 are
set to a value other than '00', the AD0LJST bit in the ADC0CN register must be
set to '0' (right justified).
00: 1 conversion is performed.
01: 4 conversions are performed and accumulated.
10: 8 conversions are performed and accumulated.
11: 16 conversions are performed and accumulated.
0
GAINEN
Gain Enable Bit.
Controls the gain programming. Refer to Section “6.3. Selectable Gain” on page 53
for information about using this bit.
58
Rev. 1.2
C8051F55x/56x/57x
SFR Definition 6.5. ADC0H: ADC0 Data Word MSB
Bit
7
6
5
4
3
Name
ADC0H[7:0]
Type
R/W
Reset
0
0
0
0
SFR Address = 0xBE; SFR Page = 0x00
Bit
Name
0
2
1
0
0
0
0
Function
7:0 ADC0H[7:0] ADC0 Data Word High-Order Bits.
For AD0LJST = 0 and AD0RPT as follows:
00: Bits 3–0 are the upper 4 bits of the 12-bit result. Bits 7–4 are 0000b.
01: Bits 4–0 are the upper 5 bits of the 14-bit result. Bits 7–5 are 000b.
10: Bits 5–0 are the upper 6 bits of the 15-bit result. Bits 7–6 are 00b.
11: Bits 7–0 are the upper 8 bits of the 16-bit result.
For AD0LJST = 1 (AD0RPT must be 00): Bits 7–0 are the most-significant bits of the
ADC0 12-bit result.
SFR Definition 6.6. ADC0L: ADC0 Data Word LSB
Bit
7
6
5
4
3
Name
ADC0L[7:0]
Type
R/W
Reset
0
0
0
SFR Address = 0xBD; SFR Page = 0x00
Bit
Name
7:0
0
0
2
1
0
0
0
0
Function
ADC0L[7:0] ADC0 Data Word Low-Order Bits.
For AD0LJST = 0: Bits 7–0 are the lower 8 bits of the ADC0 Accumulated Result.
For AD0LJST = 1 (AD0RPT must be '00'): Bits 7–4 are the lower 4 bits of the 12-bit
result. Bits 3–0 are 0000b.
Rev. 1.2
59
C8051F55x/56x/57x
SFR Definition 6.7. ADC0CN: ADC0 Control
Bit
7
6
5
4
Name
AD0EN
BURSTEN
AD0INT
Type
R/W
R/W
R/W
R/W
Reset
0
0
0
0
3
AD0BUSY AD0WINT
2
1
0
AD0LJST
AD0CM[1:0]
R/W
R/W
R/W
0
0
0
0
SFR Address = 0xE8; SFR Page = 0x00; Bit-Addressable
Bit
Name
Function
7
AD0EN
ADC0 Enable Bit.
0: ADC0 Disabled. ADC0 is in low-power shutdown.
1: ADC0 Enabled. ADC0 is active and ready for data conversions.
6
BURSTEN ADC0 Burst Mode Enable Bit.
0: Burst Mode Disabled.
1: Burst Mode Enabled.
5
AD0INT
ADC0 Conversion Complete Interrupt Flag.
0: ADC0 has not completed a data conversion since AD0INT was last cleared.
1: ADC0 has completed a data conversion.
4
AD0BUSY
ADC0 Busy Bit.
Read:
Write:
0: ADC0 conversion is not 0: No Effect.
in progress.
1: Initiates ADC0 Conver1: ADC0 conversion is in
sion if AD0CM[1:0] = 00b
progress.
3
AD0WINT
ADC0 Window Compare Interrupt Flag.
This bit must be cleared by software
0: ADC0 Window Comparison Data match has not occurred since this flag was last
cleared.
1: ADC0 Window Comparison Data match has occurred.
2
AD0LJST
ADC0 Left Justify Select Bit.
0: Data in ADC0H:ADC0L registers is right-justified
1: Data in ADC0H:ADC0L registers is left-justified. This option should not be used
with a repeat count greater than 1 (when AD0RPT[1:0] is 01b, 10b, or 11b).
1:0 AD0CM[1:0] ADC0 Start of Conversion Mode Select.
00: ADC0 start-of-conversion source is write of 1 to AD0BUSY.
01: ADC0 start-of-conversion source is overflow of Timer 1.
10: ADC0 start-of-conversion source is rising edge of external CNVSTR.
11: ADC0 start-of-conversion source is overflow of Timer 2.
60
Rev. 1.2
C8051F55x/56x/57x
SFR Definition 6.8. ADC0TK: ADC0 Tracking Mode Select
Bit
7
6
5
4
3
2
1
0
Name
AD0PWR[3:0]
AD0TM[1:0]
AD0TK[1:0]
Type
R/W
R/W
R/W
Reset
1
1
1
1
1
SFR Address = 0xBA; SFR Page = 0x00
Bit
Name
7:4
1
1
1
Function
AD0PWR[3:0] ADC0 Burst Power-up Time.
For BURSTEN = 0: ADC0 Power state controlled by AD0EN
For BURSTEN = 1, AD0EN = 1: ADC0 remains enabled and does not enter the
very low power state
For BURSTEN = 1, AD0EN = 0: ADC0 enters the very low power state and is
enabled after each convert start signal. The Power-up time is programmed according the following equation:
Tstartup
AD0PWR = ------------------------ – 1 or Tstartup = ( AD0PWR + 1 )200ns
200ns
3:2
AD0TM[1:0]
ADC0 Tracking Mode Enable Select Bits.
00: Reserved.
01: ADC0 is configured to Post-Tracking Mode.
10: ADC0 is configured to Pre-Tracking Mode.
11: ADC0 is configured to Dual Tracking Mode.
1:0
AD0TK[1:0]
ADC0 Post-Track Time.
00: Post-Tracking time is equal to 2 SAR clock cycles + 2 FCLK cycles.
01: Post-Tracking time is equal to 4 SAR clock cycles + 2 FCLK cycles.
10: Post-Tracking time is equal to 8 SAR clock cycles + 2 FCLK cycles.
11: Post-Tracking time is equal to 16 SAR clock cycles + 2 FCLK cycles.
6.4. Programmable Window Detector
The ADC Programmable Window Detector continuously compares the ADC0 output registers to user-programmed limits, and notifies the system when a desired condition is detected. This is especially effective in
an interrupt-driven system, saving code space and CPU bandwidth while delivering faster system
response times. The window detector interrupt flag (AD0WINT in register ADC0CN) can also be used in
polled mode. The ADC0 Greater-Than (ADC0GTH, ADC0GTL) and Less-Than (ADC0LTH, ADC0LTL)
registers hold the comparison values. The window detector flag can be programmed to indicate when measured data is inside or outside of the user-programmed limits, depending on the contents of the ADC0
Less-Than and ADC0 Greater-Than registers.
Rev. 1.2
61
C8051F55x/56x/57x
SFR Definition 6.9. ADC0GTH: ADC0 Greater-Than Data High Byte
Bit
7
6
5
4
3
Name
ADC0GTH[7:0]
Type
R/W
Reset
1
1
1
1
1
SFR Address = 0xC4; SFR Page = 0x00
Bit
Name
2
1
0
1
1
1
2
1
0
1
1
1
Function
7:0 ADC0GTH[7:0] ADC0 Greater-Than Data Word High-Order Bits.
SFR Definition 6.10. ADC0GTL: ADC0 Greater-Than Data Low Byte
Bit
7
6
5
4
3
Name
ADC0GTL[7:0]
Type
R/W
Reset
1
1
1
1
SFR Address = 0xC3; SFR Page = 0x00
Bit
Name
7:0
62
1
Function
ADC0GTL[7:0] ADC0 Greater-Than Data Word Low-Order Bits.
Rev. 1.2
C8051F55x/56x/57x
SFR Definition 6.11. ADC0LTH: ADC0 Less-Than Data High Byte
Bit
7
6
5
4
3
Name
ADC0LTH[7:0]
Type
R/W
Reset
0
0
0
0
0
SFR Address = 0xC6; SFR Page = 0x00
Bit
Name
7:0
2
1
0
0
0
0
2
1
0
0
0
0
Function
ADC0LTH[7:0] ADC0 Less-Than Data Word High-Order Bits.
SFR Definition 6.12. ADC0LTL: ADC0 Less-Than Data Low Byte
Bit
7
6
5
4
3
Name
ADC0LTL[7:0]
Type
R/W
Reset
0
0
0
SFR Address = 0xC5; SFR Page = 0x00
Bit
Name
7:0
0
0
Function
ADC0LTL[7:0] ADC0 Less-Than Data Word Low-Order Bits.
6.4.1. Window Detector In Single-Ended Mode
Figure 6.6
shows
two
example
window
comparisons
for
right-justified
data
with
ADC0LTH:ADC0LTL = 0x0200 (512d) and ADC0GTH:ADC0GTL = 0x0100 (256d). The input voltage can
range from 0 to VREF x (4095/4096) with respect to GND, and is represented by a 12-bit unsigned integer
value. The repeat count is set to one. In the left example, an AD0WINT interrupt will be generated if the
ADC0 conversion word (ADC0H:ADC0L) is within the range defined by ADC0GTH:ADC0GTL and
ADC0LTH:ADC0LTL (if 0x0100 < ADC0H:ADC0L < 0x0200). In the right example, and AD0WINT interrupt
will be generated if the ADC0 conversion word is outside of the range defined by the ADC0GT and
ADC0LT registers (if ADC0H:ADC0L < 0x0100 or ADC0H:ADC0L > 0x0200). Figure 6.7 shows an example using left-justified data with the same comparison values.
Rev. 1.2
63
C8051F55x/56x/57x
ADC0H:ADC0L
ADC0H:ADC0L
Input Voltage
(Px.x - GND)
VREF x (4095/4096)
Input Voltage
(Px.x - GND)
0x0FFF
VREF x (1023/
1024)
0x0FFF
AD0WINT
not affected
AD0WINT=1
0x0201
VREF x (512/4096)
0x0200
0x0201
ADC0LTH:ADC0LTL
VREF x (512/4096)
0x01FF
0x0200
0x01FF
AD0WINT=1
0x0101
VREF x (256/4096)
0x0100
0x0101
ADC0GTH:ADC0GTL
VREF x (256/4096)
0x00FF
0x0100
ADC0GTH:ADC0GTL
AD0WINT
not affected
ADC0LTH:ADC0LTL
0x00FF
AD0WINT=1
AD0WINT
not affected
0
0x0000
0
0x0000
Figure 6.6. ADC Window Compare Example: Right-Justified Data
ADC0H:ADC0L
ADC0H:ADC0L
Input Voltage
(Px.x - GND)
VREF x (4095/4096)
Input Voltage
(Px.x - GND)
0xFFF0
VREF x (4095/4096)
0xFFF0
AD0WINT
not affected
AD0WINT=1
0x2010
VREF x (512/4096)
0x2000
0x2010
ADC0LTH:ADC0LTL
VREF x (512/4096)
0x1FF0
0x2000
0x1FF0
AD0WINT=1
0x1010
VREF x (256/4096)
0x1000
0x1010
ADC0GTH:ADC0GTL
VREF x (256/4096)
0x0FF0
0x1000
ADC0GTH:ADC0GTL
AD0WINT
not affected
ADC0LTH:ADC0LTL
0x0FF0
AD0WINT=1
AD0WINT
not affected
0
0x0000
0
0x0000
Figure 6.7. ADC Window Compare Example: Left-Justified Data
64
Rev. 1.2
C8051F55x/56x/57x
6.5. ADC0 Analog Multiplexer
ADC0 includes an analog multiplexer to enable multiple analog input sources. Any of the following may be
selected as an input: P0.0–P3.7, the on-chip temperature sensor, the core power supply (VDD), or ground
(GND). ADC0 is single-ended and all signals measured are with respect to GND. The ADC0 input
channels are selected using the ADC0MX register as described in SFR Definition 6.13.
ADC0MX5
ADC0MX4
ADC0MX3
ADC0MX2
ADC0MX1
ADC0MX0
ADC0MX
P0.0
P0.7
P1.0
P1.7
P2.0
P2.7
ADC0
AMUX
P3.0
P2.2-P2.7, P3.0 available as
inputs on 40-pin and 32-pin
packages
P3.7
Temp
Sensor
VDD
GND
P3.1-P3.7 available as inputs on
48-pin and 40-pin packages
Figure 6.8. ADC0 Multiplexer Block Diagram
Important Note About ADC0 Input Configuration: Port pins selected as ADC0 inputs should be configured as analog inputs, and should be skipped by the Digital Crossbar. To configure a Port pin for analog
input, set to 0 the corresponding bit in register PnMDIN. To force the Crossbar to skip a Port pin, set to 1
the corresponding bit in register PnSKIP. See Section “19. Port Input/Output” on page 169 for more Port
I/O configuration details.
Rev. 1.2
65
C8051F55x/56x/57x
SFR Definition 6.13. ADC0MX: ADC0 Channel Select
Bit
Name
Type
Reset
7
6
5
4
R
0
R
0
1
1
SFR Address = 0xBB; SFR Page = 0x00;
Bit
Name
3
2
ADC0MX[5:0]
R/W
1
1
1
0
1
1
Function
7:6
Unused
Read = 00b; Write = Don’t Care.
5:0 AMX0P[5:0] AMUX0 Positive Input Selection.
000000:
000001:
000010:
000011:
000100:
000101:
000110:
000111:
001000:
001001:
001010:
001011:
001100:
001101:
001110:
001111:
010000:
010001:
010010:
010011:
010100:
010101:
010110:
010111:
011000:
011001:
011010:
011011:
011100:
011101:
011110:
011111:
100000–101111:
110000:
110001:
110010–111111:
66
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
P2.0
P2.1
P2.2 (Only available on 40-pin and 32-pin package devices)
P2.3 (Only available on 40-pin and 32-pin package devices)
P2.4 (Only available on 40-pin and 32-pin package devices)
P2.5 (Only available on 40-pin and 32-pin package devices)
P2.6 (Only available on 40-pin and 32-pin package devices)
P2.7 (Only available on 40-pin and 32-pin package devices)
P3.0 (Only available on 40-pin and 32-pin package devices)
P3.1 (Only available on 40-pin package devices)
P3.2 (Only available on 40-pin package devices)
P3.3 (Only available on 40-pin package devices)
P3.4 (Only available on 40-pin package devices)
P3.5 (Only available on 40-pin package devices)
P3.6 (Only available on 40-pin package devices)
P3.7 (Only available on 40-pin package devices)
Reserved
Temp Sensor
VDD
GND
Rev. 1.2
C8051F55x/56x/57x
6.6. Temperature Sensor
An on-chip temperature sensor is included on the C8051F55x/56x/57x devices which can be directly
accessed via the ADC multiplexer in single-ended configuration. To use the ADC to measure the temperature sensor, the ADC multiplexer channel should be configured to connect to the temperature sensor. The
temperature sensor transfer function is shown in Figure 6.9. The output voltage (VTEMP) is the positive
ADC input is selected by bits AD0MX[4:0] in register ADC0MX. The TEMPE bit in register REF0CN
enables/disables the temperature sensor, as described in SFR Definition 7.1. While disabled, the temperature sensor defaults to a high impedance state and any ADC measurements performed on the sensor will
result in meaningless data. Refer to Table 5.10 for the slope and offset parameters of the temperature sensor.
VTEMP = (Slope x TempC) + Offset
Voltage
TempC = (VTEMP - Offset) / Slope
Slope (V / deg C)
Offset (V at 0 Celsius)
Temperature
Figure 6.9. Temperature Sensor Transfer Function
Rev. 1.2
67
C8051F55x/56x/57x
7. Voltage Reference
The Voltage reference multiplexer on the C8051F55x/56x/57x devices is configurable to use an externally
connected voltage reference, the on-chip reference voltage generator routed to the VREF pin, or the VDD
power supply voltage (see Figure 7.1). The REFSL bit in the Reference Control register (REF0CN, SFR
Definition 7.1) selects the reference source for the ADC. For an external source or the on-chip reference,
REFSL should be set to 0 to select the VREF pin. To use VDD as the reference source, REFSL should be
set to 1.
The BIASE bit enables the internal voltage bias generator, which is used by the ADC, Temperature Sensor,
and internal oscillator. This bias is automatically enabled when any peripheral which requires it is enabled,
and it does not need to be enabled manually. The bias generator may be enabled manually by writing a 1
to the BIASE bit in register REF0CN. The electrical specifications for the voltage reference circuit are given
in Table 5.11.
The on-chip voltage reference circuit consists of a temperature stable bandgap voltage reference generator and a gain-of-two output buffer amplifier. The output voltage is selectable between 1.5 V and 2.25 V.
The on-chip voltage reference can be driven on the VREF pin by setting the REFBE bit in register REF0CN
to a 1. The maximum load seen by the VREF pin must be less than 200 µA to GND. Bypass capacitors of
0.1 µF and 4.7 µF are recommended from the VREF pin to GND. If the on-chip reference is not used, the
REFBE bit should be cleared to 0. Electrical specifications for the on-chip voltage reference are given in
Table 5.11.
Important Note about the VREF Pin: When using either an external voltage reference or the on-chip reference circuitry, the VREF pin should be configured as an analog pin and skipped by the Digital Crossbar.
Refer to Section “19. Port Input/Output” on page 169 for the location of the VREF pin, as well as details of
how to configure the pin in analog mode and to be skipped by the crossbar. If VDD is selected as the voltage reference in the REF0CN register and the ADC is enabled in the ADC0CN register, the P0.0/VREF pin
cannot operate as a general purpose I/O pin in open-drain mode. With the above settings, this pin can
operate in push-pull output mode or as an analog input.
REFSL
TEMPE
BIASE
REFBE
REF0CN
EN
VDD
External
Voltage
Reference
Circuit
R1
Bias Generator
To ADC, Internal
Oscillators
IOSCE
N
EN
VREF
Temp Sensor
To Analog Mux
0
VREF
(to ADC)
GND
VDD
1
REFBE
4.7μF
+
0.1μF
Recommended Bypass
Capacitors
EN
Internal
Reference
Figure 7.1. Voltage Reference Functional Block Diagram
Rev. 1.2
68
C8051F55x/56x/57x
SFR Definition 7.1. REF0CN: Reference Control
Bit
7
6
Name
5
4
3
2
1
0
ZTCEN
REFLV
REFSL
TEMPE
BIASE
REFBE
Type
R
R
R
R
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Address = 0xD1; SFR Page = 0x00
Bit
Name
Function
7:6
Unused
Read = 00b; Write = don’t care.
5
ZTCEN
Zero Temperature Coefficient Bias Enable Bit.
This bit must be set to 1b before entering oscillator suspend mode.
0: ZeroTC Bias Generator automatically enabled when required.
1: ZeroTC Bias Generator forced on.
4
REFLV
Voltage Reference Output Level Select.
This bit selects the output voltage level for the internal voltage reference
0: Internal voltage reference set to 1.5 V.
1: Internal voltage reference set to 2.20 V.
3
REFSL
Voltage Reference Select.
This bit selects the ADCs voltage reference.
0: VREF pin used as voltage reference.
1: VDD used as voltage reference. If VDD is selected as the voltage reference and the
ADC is enabled in the ADC0CN register, the P0.0/VREF pin cannot operate as a general purpose I/O pin in open-drain mode. With the above settings, this pin can operate
in push-pull output mode or as an analog input.
2
TEMPE
Temperature Sensor Enable Bit.
0: Internal Temperature Sensor off.
1: Internal Temperature Sensor on.
1
BIASE
Internal Analog Bias Generator Enable Bit.
0: Internal Bias Generator off.
1: Internal Bias Generator on.
0
REFBE
On-chip Reference Buffer Enable Bit.
0: On-chip Reference Buffer off.
1: On-chip Reference Buffer on. Internal voltage reference driven on the VREF pin.
69
Rev. 1.2
C8051F55x/56x/57x
8. Comparators
The C8051F55x/56x/57x devices include two on-chip programmable voltage Comparators. A block diagram of the comparators is shown in Figure 8.1, where “n” is the comparator number (0 or 1). The two
Comparators operate identically except that Comparator0 can also be used a reset source. For input
selection details, refer to SFR Definition 8.5 and SFR Definition 8.6.
Each Comparator offers programmable response time and hysteresis, an analog input multiplexer, and two
outputs that are optionally available at the Port pins: a synchronous “latched” output (CP0, CP1), or an
asynchronous “raw” output (CP0A, CP1A). The asynchronous signal is available even when the system
clock is not active. This allows the Comparators to operate and generate an output with the device in
STOP mode. When assigned to a Port pin, the Comparator outputs may be configured as open drain or
push-pull (see Section “19.4. Port I/O Initialization” on page 174). Comparator0 may also be used as a
reset source (see Section “16.5. Comparator0 Reset” on page 142).
The Comparator0 inputs are selected in the CPT0MX register (SFR Definition 8.5). The CMX0P1-CMX0P0
bits select the Comparator0 positive input; the CMX0N1-CMX0N0 bits select the Comparator0 negative
input. The Comparator1 inputs are selected in the CPT1MX register (SFR Definition 8.6). The CMX1P1CMX1P0 bits select the Comparator1 positive input; the CMX1N1-CMX1N0 bits select the Comparator1
negative input.
Important Note About Comparator Inputs: The Port pins selected as Comparator inputs should be configured as analog inputs in their associated Port configuration register, and configured to be skipped by the
Crossbar (for details on Port configuration, see Section “19.1. Port I/O Modes of Operation” on page 170).
CPTnCN
CPnEN
CPnOUT
CPnRIF
CPnFIF
CPnHYP1
CPnHYP0
CPnHYN1
CPnHYN0
VIO
CPn +
Comparator
Input Mux
+
CPn -
CPn
D
-
SET
CLR
Q
D
Q
SET
CLR
Q
Q
Crossbar
(SYNCHRONIZER)
CPnA
GND
CPTnMD
CPnRIE
CPnFIE
CPnMD1
CPnMD0
Reset
Decision
Tree
CPnRIF
CPnFIF
0
CPnEN
EA
1
0
0
0
1
1
CPn
Interrupt
1
Figure 8.1. Comparator Functional Block Diagram
Rev. 1.2
70
C8051F55x/56x/57x
Comparator outputs can be polled in software, used as an interrupt source, and/or routed to a Port pin.
When routed to a Port pin, Comparator outputs are available asynchronous or synchronous to the system
clock; the asynchronous output is available even in STOP mode (with no system clock active). When disabled, the Comparator output (if assigned to a Port I/O pin via the Crossbar) defaults to the logic low state,
and the power supply to the comparator is turned off. See Section “19.3. Priority Crossbar Decoder” on
page 172 for details on configuring Comparator outputs via the digital Crossbar. Comparator inputs can be
externally driven from –0.25 V to (VDD) + 0.25 V without damage or upset. The complete Comparator electrical specifications are given in Table 5.12.
The Comparator response time may be configured in software via the CPTnMD registers (see SFR Definition 8.2). Selecting a longer response time reduces the Comparator supply current. See Table 5.12 for
complete timing and supply current requirements.
VIN+
VIN-
CPn+
CPn-
+
CPn
_
OUT
CIRCUIT CONFIGURATION
Positive Hysteresis Voltage
(Programmed with CPnHYP Bits)
VIN-
INPUTS
Negative Hysteresis Voltage
(Programmed by CPnHYN Bits)
VIN+
VOH
OUTPUT
VOL
Negative Hysteresis
Disabled
Positive Hysteresis
Disabled
Maximum
Negative Hysteresis
Maximum
Positive Hysteresis
Figure 8.2. Comparator Hysteresis Plot
Comparator hysteresis is software-programmable via its Comparator Control register CPTnCN.
The amount of negative hysteresis voltage is determined by the settings of the CPnHYN bits. As shown in
Figure 8.2, various levels of negative hysteresis can be programmed, or negative hysteresis can be disabled. In a similar way, the amount of positive hysteresis is determined by the setting the CPnHYP bits.
Comparator interrupts can be generated on both rising-edge and falling-edge output transitions. (For Interrupt enable and priority control, see “13. Interrupts” .) The CPnFIF flag is set to 1 upon a Comparator falling-edge, and the CPnRIF flag is set to 1 upon the Comparator rising-edge. Once set, these bits remain
set until cleared by software. The output state of the Comparator can be obtained at any time by reading
the CPnOUT bit. The Comparator is enabled by setting the CPnEN bit to 1, and is disabled by clearing this
bit to 0.
71
Rev. 1.2
C8051F55x/56x/57x
Note that false rising edges and falling edges can be detected when the comparator is first powered on or
if changes are made to the hysteresis or response time control bits. Therefore, it is recommended that the
rising-edge and falling-edge flags be explicitly cleared to logic 0 a short time after the comparator is
enabled or its mode bits have been changed.
SFR Definition 8.1. CPT0CN: Comparator0 Control
Bit
7
6
5
4
3
Name
CP0EN
CP0OUT
CP0RIF
CP0FIF
CP0HYP[1:0]
CP0HYN[1:0]
Type
R/W
R
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
SFR Address = 0x9A; SFR Page = 0x00
Bit
Name
7
CP0EN
2
0
1
0
0
0
Function
Comparator0 Enable Bit.
0: Comparator0 Disabled.
1: Comparator0 Enabled.
6
CP0OUT
Comparator0 Output State Flag.
0: Voltage on CP0+ < CP0–.
1: Voltage on CP0+ > CP0–.
5
CP0RIF
Comparator0 Rising-Edge Flag. Must be cleared by software.
0: No Comparator0 Rising Edge has occurred since this flag was last cleared.
1: Comparator0 Rising Edge has occurred.
4
CP0FIF
Comparator0 Falling-Edge Flag. Must be cleared by software.
0: No Comparator0 Falling-Edge has occurred since this flag was last cleared.
1: Comparator0 Falling-Edge has occurred.
3:2 CP0HYP[1:0] Comparator0 Positive Hysteresis Control Bits.
00: Positive Hysteresis Disabled.
01: Positive Hysteresis = 5 mV.
10: Positive Hysteresis = 10 mV.
11: Positive Hysteresis = 20 mV.
1:0 CP0HYN[1:0] Comparator0 Negative Hysteresis Control Bits.
00: Negative Hysteresis Disabled.
01: Negative Hysteresis = 5 mV.
10: Negative Hysteresis = 10 mV.
11: Negative Hysteresis = 20 mV.
Rev. 1.2
72
C8051F55x/56x/57x
SFR Definition 8.2. CPT0MD: Comparator0 Mode Selection
Bit
7
6
Name
5
4
CP0RIE
CP0FIE
3
2
R
R
R/W
R/W
R
R
Reset
0
0
0
0
0
0
Unused
Read = 00b, Write = Don’t Care.
5
CP0RIE
Comparator0 Rising-Edge Interrupt Enable.
0: Comparator0 Rising-edge interrupt disabled.
1: Comparator0 Rising-edge interrupt enabled.
4
CP0FIE
Comparator0 Falling-Edge Interrupt Enable.
0: Comparator0 Falling-edge interrupt disabled.
1: Comparator0 Falling-edge interrupt enabled.
3:2
Unused
Read = 00b, Write = don’t care.
73
R/W
1
Function
7:6
1:0
0
CP0MD[1:0]
Type
SFR Address = 0x9B; SFR Page = 0x00
Bit
Name
1
CP0MD[1:0] Comparator0 Mode Select.
These bits affect the response time and power consumption for Comparator0.
00: Mode 0 (Fastest Response Time, Highest Power Consumption)
01: Mode 1
10: Mode 2
11: Mode 3 (Slowest Response Time, Lowest Power Consumption)
Rev. 1.2
0
C8051F55x/56x/57x
SFR Definition 8.3. CPT1CN: Comparator1 Control
Bit
7
6
5
4
3
Name
CP1EN
CP1OUT
CP1RIF
CP1FIF
CP1HYP[1:0]
CP1HYN[1:0]
Type
R/W
R
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
SFR Address = 0x9D; SFR Page = 0x00
Bit
Name
7
CP1EN
2
0
1
0
0
0
Function
Comparator1 Enable Bit.
0: Comparator1 Disabled.
1: Comparator1 Enabled.
6
CP1OUT
Comparator1 Output State Flag.
0: Voltage on CP1+ < CP1–.
1: Voltage on CP1+ > CP1–.
5
CP1RIF
Comparator1 Rising-Edge Flag. Must be cleared by software.
0: No Comparator1 Rising Edge has occurred since this flag was last cleared.
1: Comparator1 Rising Edge has occurred.
4
CP1FIF
Comparator1 Falling-Edge Flag. Must be cleared by software.
0: No Comparator1 Falling-Edge has occurred since this flag was last cleared.
1: Comparator1 Falling-Edge has occurred.
3:2 CP1HYP[1:0] Comparator1 Positive Hysteresis Control Bits.
00: Positive Hysteresis Disabled.
01: Positive Hysteresis = 5 mV.
10: Positive Hysteresis = 10 mV.
11: Positive Hysteresis = 20 mV.
1:0 CP1HYN[1:0] Comparator1 Negative Hysteresis Control Bits.
00: Negative Hysteresis Disabled.
01: Negative Hysteresis = 5 mV.
10: Negative Hysteresis = 10 mV.
11: Negative Hysteresis = 20 mV.
Rev. 1.2
74
C8051F55x/56x/57x
SFR Definition 8.4. CPT1MD: Comparator1 Mode Selection
Bit
7
6
Name
5
4
CP1RIE
CP1FIE
3
2
R
R
R/W
R/W
R
R
Reset
0
0
0
0
0
0
Unused
Read = 00b, Write = Don’t Care.
5
CP1RIE
Comparator1 Rising-Edge Interrupt Enable.
0: Comparator1 Rising-edge interrupt disabled.
1: Comparator1 Rising-edge interrupt enabled.
4
CP1FIE
Comparator1 Falling-Edge Interrupt Enable.
0: Comparator1 Falling-edge interrupt disabled.
1: Comparator1 Falling-edge interrupt enabled.
3:2
Unused
Read = 00b, Write = don’t care.
75
R/W
1
Function
7:6
1:0
0
CP1MD[1:0]
Type
SFR Address = 0x9E; SFR Page = 0x00
Bit
Name
1
CP1MD[1:0] Comparator1 Mode Select.
These bits affect the response time and power consumption for Comparator1.
00: Mode 0 (Fastest Response Time, Highest Power Consumption)
01: Mode 1
10: Mode 2
11: Mode 3 (Slowest Response Time, Lowest Power Consumption)
Rev. 1.2
0
C8051F55x/56x/57x
8.1. Comparator Multiplexer
C8051F55x/56x/57x devices include an analog input multiplexer for each of the comparators to connect
Port I/O pins to the comparator inputs. The Comparator0 inputs are selected in the CPT0MX register (SFR
Definition 8.5). The CMX0P3–CMX0P0 bits select the Comparator0 positive input; the CMX0N3–CMX0N0
bits select the Comparator0 negative input. Similarly, the Comparator1 inputs are selected in the CPT1MX
register using the CMX1P3-CMX1P0 bits and CMX1N3–CMX1N0 bits. The same pins are available to both
multiplexers at the same time and can be used by both comparators simultaneously.
Important Note About Comparator Inputs: The Port pins selected as comparator inputs should be configured as analog inputs in their associated Port configuration register, and configured to be skipped by the
Crossbar (for details on Port configuration, see Section “19.6. Special Function Registers for Accessing
and Configuring Port I/O” on page 183).
CPTnMX
CMXnN3
CMXnN2
CMXnN1
CMXnN0
CMXnP3
CMXnP2
CMXnP1
CMXnP0
P0.0
VDD
P0.2
P0.1
CPn +
P0.4
P0.3
P0.6
P0.5
P1.0
+
P1.2
-
P0.7
P1.1
P1.4
P1.3
GND
P1.6
P1.5
P2.0
P1.7
P2.2
P2.1
P2.4
P2.3
P2.6
P2.5
P2.7
CPn -
Figure 8.3. Comparator Input Multiplexer Block Diagram
Rev. 1.2
76
C8051F55x/56x/57x
SFR Definition 8.5. CPT0MX: Comparator0 MUX Selection
Bit
7
6
5
4
3
2
1
Name
CMX0N[3:0]
CMX0P[3:0]
Type
R/W
R/W
Reset
0
1
1
1
SFR Address = 0x9C; SFR Page = 0x00
Bit
Name
7:4
3:0
77
0
1
1
Function
CMX0N[3:0] Comparator0 Negative Input MUX Selection.
0000:
P0.1
0001:
P0.3
0010:
P0.5
0011:
P0.7
0100:
P1.1
0101:
P1.3
0110:
P1.5
0111:
P1.7
1000:
P2.1
1001:
P2.3 (only available on 40-pin and 32-pin devices)
1010:
P2.5 (only available on 40-pin and 32-pin devices)
1011:
P2.7 (only available on 40-pin and 32-pin devices)
1100–1111:
None
CMX0P[3:0] Comparator0 Positive Input MUX Selection.
0000:
P0.0
0001:
P0.2
0010:
P0.4
0011:
P0.6
0100:
P1.0
0101:
P1.2
0110:
P1.4
0111:
P1.6
1000:
P2.0
1001:
P2.2 (only available on 40-pin and 32-pin devices)
1010:
P2.4 (only available on 40-pin and 32-pin devices)
1011:
P2.6 (only available on 40-pin and 32-pin devices)
1100–1111:
None
Rev. 1.2
0
1
C8051F55x/56x/57x
SFR Definition 8.6. CPT1MX: Comparator1 MUX Selection
Bit
7
6
5
4
3
2
1
Name
CMX1N[3:0]
CMX1P[3:0]
Type
R/W
R/W
Reset
0
1
1
1
SFR Address = 0x9F; SFR Page = 0x00
Bit
Name
7:4
3:0
0
1
1
0
1
Function
CMX1N[3:0] Comparator1 Negative Input MUX Selection.
0000:
P0.1
0001:
P0.3
0010:
P0.5
0011:
P0.7
0100:
P1.1
0101:
P1.3
0110:
P1.5
0111:
P1.7
1000:
P2.1
1001:
P2.3 (only available on 40-pin and 32-pin devices)
1010:
P2.5 (only available on 40-pin and 32-pin devices)
1011:
P2.7 (only available on 40-pin and 32-pin devices)
1100–1111:
None
CMX1P[3:0] Comparator1 Positive Input MUX Selection.
0000:
P0.0
0001:
P0.2
0010:
P0.4
0011:
P0.6
0100:
P1.0
0101:
P1.2
0110:
P1.4
0111:
P1.6
1000:
P2.0
1001:
P2.2 (only available on 40-pin and 32-pin devices)
1010:
P2.4 (only available on 40-pin and 32-pin devices)
1011:
P2.6 (only available on 40-pin and 32-pin devices)
1100–1111:
None
Rev. 1.2
78
C8051F55x/56x/57x
9. Voltage Regulator (REG0)
C8051F55x/56x/57x devices include an on-chip low dropout voltage regulator (REG0). The input to REG0
at the VREGIN pin can be as high as 5.25 V. The output can be selected by software to 2.1 V or 2.6 V. When
enabled, the output of REG0 appears on the VDD pin, powers the microcontroller core, and can be used to
power external devices. On reset, REG0 is enabled and can be disabled by software.
The Voltage regulator can generate an interrupt (if enabled by EREG0, EIE2.0) that is triggered whenever
the VREGIN input voltage drops below the dropout threshold voltage. This dropout interrupt has no pending
flag and the recommended procedure to use it is as follows:
1. Wait enough time to ensure the VREGIN input voltage is stable
2. Enable the dropout interrupt (EREG0, EIE2.0) and select the proper priority (PREG0, EIP2.0)
3. If triggered, inside the interrupt disable it (clear EREG0, EIE2.0), execute all procedures necessary to
protect your application (put it in a safe mode and leave the interrupt now disabled.
4. In the main application, now running in the safe mode, regularly checks the DROPOUT bit
(REG0CN.0). Once it is cleared by the regulator hardware the application can enable the interrupt
again (EREG0, EIE1.6) and return to the normal mode operation.
The input (VREGIN) and output (VDD) of the voltage regulator should both be bypassed with a large capacitor (4.7 µF + 0.1 µF) to ground as shown in Figure 9.1. This capacitor will eliminate power spikes and provide any immediate power required by the microcontroller. The settling time associated with the voltage
regulator is shown in Table 5.8 on page 43.
Note: The output of the internal voltage regulator is calibrated by the MCU immediately after any reset
event. The output of the un-calibrated internal regulator could be below the high threshold setting of
the VDD Monitor. If this is the case and the VDD Monitor is set to the high threshold setting and if the
MCU receives a non-power on reset (POR), the MCU will remain in reset until a POR occurs (i.e.,
VDD Monitor will keep the device in reset). A POR will force the VDD Monitor to the low threshold
setting which is guaranteed to be below the un-calibrated output of the internal regulator. The device
will then exit reset and resume normal operation. It is for this reason Silicon Labs strongly
recommends that the VDD Monitor is always left in the low threshold setting (i.e. default value upon
POR).
REG0
VREGIN
4.7 µF
.1 µF
VDD
VDD
4.7 µF
.1 µF
Figure 9.1. External Capacitors for Voltage Regulator Input/Output—
Regulator Enabled
Rev. 1.2
79
C8051F55x/56x/57x
If the internal voltage regulator is not used, the VREGIN input should be tied to VDD, as shown in Figure 9.2.
VREGIN
VDD
VDD
4.7 µF
.1 µF
Figure 9.2. External Capacitors for Voltage Regulator Input/Output—Regulator Disabled
SFR Definition 9.1. REG0CN: Regulator Control
Bit
7
6
5
4
Name
REGDIS
Reserved
Type
R/W
R/W
R
R/W
R
R
R
R
Reset
0
1
0
1
0
0
0
0
REGDIS
Reserved
5
Unused
4
REG0MD
Function
Voltage Regulator Disable Bit.
Read = 1b; Must Write 1b.
Read = 0b; Write = Don’t Care.
Voltage Regulator Mode Select Bit.
0: Voltage Regulator Output is 2.1 V.
1: Voltage Regulator Output is 2.6 V.
3:1
Unused
0
DROPOUT
Read = 000b. Write = Don’t Care.
Voltage Regulator Dropout Indicator.
0: Voltage Regulator is not in dropout.
1: Voltage Regulator is in or near dropout.
80
1
Rev. 1.2
0
DROPOUT
0: Voltage Regulator Enabled
1: Voltage Regulator Disabled
6
2
REG0MD
SFR Address = 0xC9; SFR Page = 0x00
Bit
Name
7
3
C8051F55x/56x/57x
10. CIP-51 Microcontroller
The MCU system controller core is the CIP-51 microcontroller. The CIP-51 is fully compatible with the
MCS-51™ instruction set; standard 803x/805x assemblers and compilers can be used to develop software. The MCU family has a superset of all the peripherals included with a standard 8051. The CIP-51
also includes on-chip debug hardware (see description in Section 27), and interfaces directly with the analog and digital subsystems providing a complete data acquisition or control-system solution in a single integrated circuit.
The CIP-51 Microcontroller core implements the standard 8051 organization and peripherals as well as
additional custom peripherals and functions to extend its capability (see Figure 10.1 for a block diagram).
The CIP-51 includes the following features:
Fully Compatible with MCS-51 Instruction Set
50 MIPS Peak Throughput with 50 MHz Clock
0 to 50 MHz Clock Frequency
Extended Interrupt Handler
Reset Input
Power Management Modes
On-chip Debug Logic
Program and Data Memory Security
10.1. Performance
The CIP-51 employs a pipelined architecture that greatly increases its instruction throughput over the standard 8051 architecture. In a standard 8051, all instructions except for MUL and DIV take 12 or 24 system
clock cycles to execute, and usually have a maximum system clock of 12 MHz. By contrast, the CIP-51
core executes 70% of its instructions in one or two system clock cycles, with no instructions taking more
than eight system clock cycles.
Rev. 1.2
81
C8051F55x/56x/57x
D8
D8
ACCUMULATOR
STACK POINTER
TMP1
TMP2
SRAM
ADDRESS
REGISTER
PSW
D8
D8
D8
ALU
SRAM
D8
DATA BUS
B REGISTER
D8
D8
D8
DATA BUS
DATA BUS
SFR_ADDRESS
BUFFER
D8
D8
DATA POINTER
D8
SFR
BUS
INTERFACE
SFR_CONTROL
SFR_WRITE_DATA
SFR_READ_DATA
DATA BUS
PC INCREMENTER
PROGRAM COUNTER (PC)
PRGM. ADDRESS REG.
MEM_ADDRESS
D8
MEM_CONTROL
A16
MEMORY
INTERFACE
MEM_WRITE_DATA
MEM_READ_DATA
PIPELINE
RESET
D8
CONTROL
LOGIC
SYSTEM_IRQs
CLOCK
D8
STOP
IDLE
POWER CONTROL
REGISTER
INTERRUPT
INTERFACE
EMULATION_IRQ
D8
Figure 10.1. CIP-51 Block Diagram
With the CIP-51's maximum system clock at 50 MHz, it has a peak throughput of 50 MIPS. The CIP-51 has
a total of 109 instructions. The table below shows the total number of instructions that require each execution time.
Clocks to Execute
1
2
2/3
3
3/4
4
4/5
5
8
Number of Instructions
26
50
5
14
7
3
1
2
1
Programming and Debugging Support
In-system programming of the Flash program memory and communication with on-chip debug support
logic is accomplished via the Silicon Labs 2-Wire Development Interface (C2).
The on-chip debug support logic facilitates full speed in-circuit debugging, allowing the setting of hardware
breakpoints, starting, stopping and single stepping through program execution (including interrupt service
routines), examination of the program's call stack, and reading/writing the contents of registers and memory. This method of on-chip debugging is completely non-intrusive, requiring no RAM, Stack, timers, or
other on-chip resources. C2 details can be found in Section “27. C2 Interface” on page 300.
The CIP-51 is supported by development tools from Silicon Labs and third party vendors. Silicon Labs provides an integrated development environment (IDE) including editor, debugger and programmer. The IDE's
debugger and programmer interface to the CIP-51 via the C2 interface to provide fast and efficient in-system device programming and debugging. Third party macro assemblers and C compilers are also available.
82
Rev. 1.2
C8051F55x/56x/57x
10.2. Instruction Set
The instruction set of the CIP-51 System Controller is fully compatible with the standard MCS-51™ instruction set. Standard 8051 development tools can be used to develop software for the CIP-51. All CIP-51
instructions are the binary and functional equivalent of their MCS-51™ counterparts, including opcodes,
addressing modes and effect on PSW flags. However, instruction timing is different than that of the standard 8051.
10.2.1. Instruction and CPU Timing
In many 8051 implementations, a distinction is made between machine cycles and clock cycles, with
machine cycles varying from 2 to 12 clock cycles in length. However, the CIP-51 implementation is based
solely on clock cycle timing. All instruction timings are specified in terms of clock cycles.
Due to the pipelined architecture of the CIP-51, most instructions execute in the same number of clock
cycles as there are program bytes in the instruction. Conditional branch instructions take one less clock
cycle to complete when the branch is not taken as opposed to when the branch is taken. Table 10.1 is the
CIP-51 Instruction Set Summary, which includes the mnemonic, number of bytes, and number of clock
cycles for each instruction.
Rev. 1.2
83
C8051F55x/56x/57x
Table 10.1. CIP-51 Instruction Set Summary
Mnemonic
Description
Bytes
Clock
Cycles
Arithmetic Operations
ADD A, Rn
ADD A, direct
ADD A, @Ri
ADD A, #data
ADDC A, Rn
ADDC A, direct
ADDC A, @Ri
ADDC A, #data
SUBB A, Rn
SUBB A, direct
SUBB A, @Ri
SUBB A, #data
INC A
INC Rn
INC direct
INC @Ri
DEC A
DEC Rn
DEC direct
DEC @Ri
INC DPTR
MUL AB
DIV AB
DA A
Add register to A
Add direct byte to A
Add indirect RAM to A
Add immediate to A
Add register to A with carry
Add direct byte to A with carry
Add indirect RAM to A with carry
Add immediate to A with carry
Subtract register from A with borrow
Subtract direct byte from A with borrow
Subtract indirect RAM from A with borrow
Subtract immediate from A with borrow
Increment A
Increment register
Increment direct byte
Increment indirect RAM
Decrement A
Decrement register
Decrement direct byte
Decrement indirect RAM
Increment Data Pointer
Multiply A and B
Divide A by B
Decimal adjust A
1
2
1
2
1
2
1
2
1
2
1
2
1
1
2
1
1
1
2
1
1
1
1
1
1
2
2
2
1
2
2
2
1
2
2
2
1
1
2
2
1
1
2
2
1
4
8
1
AND Register to A
AND direct byte to A
AND indirect RAM to A
AND immediate to A
AND A to direct byte
AND immediate to direct byte
OR Register to A
OR direct byte to A
OR indirect RAM to A
OR immediate to A
OR A to direct byte
OR immediate to direct byte
Exclusive-OR Register to A
Exclusive-OR direct byte to A
Exclusive-OR indirect RAM to A
1
2
1
2
2
3
1
2
1
2
2
3
1
2
1
1
2
2
2
2
3
1
2
2
2
2
3
1
2
2
Logical Operations
ANL A, Rn
ANL A, direct
ANL A, @Ri
ANL A, #data
ANL direct, A
ANL direct, #data
ORL A, Rn
ORL A, direct
ORL A, @Ri
ORL A, #data
ORL direct, A
ORL direct, #data
XRL A, Rn
XRL A, direct
XRL A, @Ri
Note: Certain instructions take a variable number of clock cycles to execute depending on instruction alignment and
the FLRT setting (SFR Definition 14.3).
84
Rev. 1.2
C8051F55x/56x/57x
Table 10.1. CIP-51 Instruction Set Summary (Continued)
Mnemonic
XRL A, #data
XRL direct, A
XRL direct, #data
CLR A
CPL A
RL A
RLC A
RR A
RRC A
SWAP A
Description
Bytes
Clock
Cycles
Exclusive-OR immediate to A
Exclusive-OR A to direct byte
Exclusive-OR immediate to direct byte
Clear A
Complement A
Rotate A left
Rotate A left through Carry
Rotate A right
Rotate A right through Carry
Swap nibbles of A
2
2
3
1
1
1
1
1
1
1
2
2
3
1
2
1
1
1
1
1
Move Register to A
Move direct byte to A
Move indirect RAM to A
Move immediate to A
Move A to Register
Move direct byte to Register
Move immediate to Register
Move A to direct byte
Move Register to direct byte
Move direct byte to direct byte
Move indirect RAM to direct byte
Move immediate to direct byte
Move A to indirect RAM
Move direct byte to indirect RAM
Move immediate to indirect RAM
Load DPTR with 16-bit constant
Move code byte relative DPTR to A
Move code byte relative PC to A
Move external data (8-bit address) to A
Move A to external data (8-bit address)
Move external data (16-bit address) to A
Move A to external data (16-bit address)
Push direct byte onto stack
Pop direct byte from stack
Exchange Register with A
Exchange direct byte with A
Exchange indirect RAM with A
Exchange low nibble of indirect RAM with A
1
2
1
2
1
2
2
2
2
3
2
3
1
2
2
3
1
1
1
1
1
1
2
2
1
2
1
1
1
2
2
2
1
2
2
2
2
3
2
3
2
2
2
3
4-7*
3
3
3
3
3
2
2
1
2
2
2
Clear Carry
Clear direct bit
1
2
1
2
Data Transfer
MOV A, Rn
MOV A, direct
MOV A, @Ri
MOV A, #data
MOV Rn, A
MOV Rn, direct
MOV Rn, #data
MOV direct, A
MOV direct, Rn
MOV direct, direct
MOV direct, @Ri
MOV direct, #data
MOV @Ri, A
MOV @Ri, direct
MOV @Ri, #data
MOV DPTR, #data16
MOVC A, @A+DPTR
MOVC A, @A+PC
MOVX A, @Ri
MOVX @Ri, A
MOVX A, @DPTR
MOVX @DPTR, A
PUSH direct
POP direct
XCH A, Rn
XCH A, direct
XCH A, @Ri
XCHD A, @Ri
Boolean Manipulation
CLR C
CLR bit
Note: Certain instructions take a variable number of clock cycles to execute depending on instruction alignment and
the FLRT setting (SFR Definition 14.3).
Rev. 1.2
85
C8051F55x/56x/57x
Table 10.1. CIP-51 Instruction Set Summary (Continued)
Mnemonic
SETB C
SETB bit
CPL C
CPL bit
ANL C, bit
ANL C, /bit
ORL C, bit
ORL C, /bit
MOV C, bit
MOV bit, C
JC rel
JNC rel
JB bit, rel
JNB bit, rel
JBC bit, rel
Description
Bytes
Clock
Cycles
Set Carry
Set direct bit
Complement Carry
Complement direct bit
AND direct bit to Carry
AND complement of direct bit to Carry
OR direct bit to carry
OR complement of direct bit to Carry
Move direct bit to Carry
Move Carry to direct bit
Jump if Carry is set
Jump if Carry is not set
Jump if direct bit is set
Jump if direct bit is not set
Jump if direct bit is set and clear bit
1
2
1
2
2
2
2
2
2
2
2
2
3
3
3
1
2
1
2
2
2
2
2
2
2
2/(4-6)*
2/(4-6)*
3/(5-7)*
3/(5-7)*
3/(5-7)*
Absolute subroutine call
Long subroutine call
Return from subroutine
Return from interrupt
Absolute jump
Long jump
Short jump (relative address)
Jump indirect relative to DPTR
Jump if A equals zero
Jump if A does not equal zero
Compare direct byte to A and jump if not equal
Compare immediate to A and jump if not equal
Compare immediate to Register and jump if not
equal
Compare immediate to indirect and jump if not
equal
Decrement Register and jump if not zero
Decrement direct byte and jump if not zero
No operation
2
3
1
1
2
3
2
1
2
2
3
3
3
4-6*
5-7*
6-8*
6-8*
4-6*
5-7*
4-6*
3-5*
2/(4-6)*
2/(4-6)*
4/(6-8)*
3/(6-8)*
3/(5-7)*
3
4/(6-8)*
2
3
1
2/(4-6)*
3/(5-7)*
1
Program Branching
ACALL addr11
LCALL addr16
RET
RETI
AJMP addr11
LJMP addr16
SJMP rel
JMP @A+DPTR
JZ rel
JNZ rel
CJNE A, direct, rel
CJNE A, #data, rel
CJNE Rn, #data, rel
CJNE @Ri, #data, rel
DJNZ Rn, rel
DJNZ direct, rel
NOP
Note: Certain instructions take a variable number of clock cycles to execute depending on instruction alignment and
the FLRT setting (SFR Definition 14.3).
86
Rev. 1.2
C8051F55x/56x/57x
Notes on Registers, Operands and Addressing Modes:
Rn—Register R0–R7 of the currently selected register bank.
@Ri—Data RAM location addressed indirectly through R0 or R1.
rel—8-bit, signed (two’s complement) offset relative to the first byte of the following instruction. Used by
SJMP and all conditional jumps.
direct—8-bit internal data location’s address. This could be a direct-access Data RAM location (0x00–
0x7F) or an SFR (0x80–0xFF).
#data—8-bit constant
#data16—16-bit constant
bit—Direct-accessed bit in Data RAM or SFR
addr11—11-bit destination address used by ACALL and AJMP. The destination must be within the
same 2 kB page of program memory as the first byte of the following instruction.
addr16—16-bit destination address used by LCALL and LJMP. The destination may be anywhere within
the 64 kB program memory space.
There is one unused opcode (0xA5) that performs the same function as NOP.
All mnemonics copyrighted © Intel Corporation 1980.
10.3. CIP-51 Register Descriptions
Following are descriptions of SFRs related to the operation of the CIP-51 System Controller. Reserved bits
should not be set to logic l. Future product versions may use these bits to implement new features in which
case the reset value of the bit will be logic 0, selecting the feature's default state. Detailed descriptions of
the remaining SFRs are included in the sections of the datasheet associated with their corresponding system function.
Rev. 1.2
87
C8051F55x/56x/57x
SFR Definition 10.1. DPL: Data Pointer Low Byte
Bit
7
6
5
4
Name
DPL[7:0]
Type
R/W
Reset
0
0
0
0
SFR Address = 0x82; SFR Page = All Pages
Bit
Name
7:0
DPL[7:0]
3
2
1
0
0
0
0
0
Function
Data Pointer Low.
The DPL register is the low byte of the 16-bit DPTR. DPTR is used to access indirectly addressed Flash memory or XRAM.
SFR Definition 10.2. DPH: Data Pointer High Byte
Bit
7
6
5
4
Name
DPH[7:0]
Type
R/W
Reset
0
0
0
0
SFR Address = 0x83; SFR Page = All Pages
Bit
Name
7:0
DPH[7:0]
3
2
1
0
0
0
0
0
Function
Data Pointer High.
The DPH register is the high byte of the 16-bit DPTR. DPTR is used to access indirectly addressed Flash memory or XRAM.
88
Rev. 1.2
C8051F55x/56x/57x
SFR Definition 10.3. SP: Stack Pointer
Bit
7
6
5
4
Name
SP[7:0]
Type
R/W
Reset
0
0
0
0
SFR Address = 0x81; SFR Page = All Pages
Bit
Name
7:0
SP[7:0]
3
2
1
0
0
1
1
1
Function
Stack Pointer.
The Stack Pointer holds the location of the top of the stack. The stack pointer is incremented before every PUSH operation. The SP register defaults to 0x07 after reset.
SFR Definition 10.4. ACC: Accumulator
Bit
7
6
5
4
Name
ACC[7:0]
Type
R/W
Reset
0
0
0
0
3
2
1
0
0
0
0
0
SFR Address = 0xE0; SFR Page = All Pages; Bit-Addressable
Bit
Name
Function
7:0
ACC[7:0]
Accumulator.
This register is the accumulator for arithmetic operations.
SFR Definition 10.5. B: B Register
Bit
7
6
5
4
Name
B[7:0]
Type
R/W
Reset
0
0
0
0
3
2
1
0
0
0
0
0
SFR Address = 0xF0; SFR Page = All Pages; Bit-Addressable
Bit
Name
Function
7:0
B[7:0]
B Register.
This register serves as a second accumulator for certain arithmetic operations.
Rev. 1.2
89
C8051F55x/56x/57x
SFR Definition 10.6. PSW: Program Status Word
Bit
7
6
5
Name
CY
AC
F0
Type
R/W
R/W
R/W
Reset
0
0
0
4
3
2
1
0
RS[1:0]
OV
F1
PARITY
R/W
R/W
R/W
R
0
0
0
0
0
SFR Address = 0xD0; SFR Page = All Pages; Bit-Addressable
Bit
Name
Function
7
CY
Carry Flag.
This bit is set when the last arithmetic operation resulted in a carry (addition) or a borrow (subtraction). It is cleared to logic 0 by all other arithmetic operations.
6
AC
Auxiliary Carry Flag.
This bit is set when the last arithmetic operation resulted in a carry into (addition) or a
borrow from (subtraction) the high order nibble. It is cleared to logic 0 by all other arithmetic operations.
5
F0
User Flag 0.
This is a bit-addressable, general purpose flag for use under software control.
4:3
RS[1:0]
Register Bank Select.
These bits select which register bank is used during register accesses.
00: Bank 0, Addresses 0x00-0x07
01: Bank 1, Addresses 0x08-0x0F
10: Bank 2, Addresses 0x10-0x17
11: Bank 3, Addresses 0x18-0x1F
2
OV
Overflow Flag.
This bit is set to 1 under the following circumstances:
An ADD, ADDC, or SUBB instruction causes a sign-change overflow.
A MUL instruction results in an overflow (result is greater than 255).
A DIV instruction causes a divide-by-zero condition.
The OV bit is cleared to 0 by the ADD, ADDC, SUBB, MUL, and DIV instructions in all
other cases.
1
F1
User Flag 1.
This is a bit-addressable, general purpose flag for use under software control.
0
PARITY
Parity Flag.
This bit is set to logic 1 if the sum of the eight bits in the accumulator is odd and cleared
if the sum is even.
90
Rev. 1.2
C8051F55x/56x/57x
10.4. Serial Number Special Function Registers (SFRs)
The C8051F55x/56x/57x devices include four SFRs, SN0 through SN3, that are pre-programmed during
production with a unique, 32-bit serial number. The serial number provides a unique identification number
for each device and can be read from the application firmware. If the serial number is not used in the application, these four registers can be used as general purpose SFRs.
SFR Definition 10.7. SNn: Serial Number n
Bit
7
6
5
4
3
Name
SERNUMn[7:0]
Type
R/W
Reset
Varies—Unique 32-bit value
2
1
0
SFR Addresses: SN0 = 0xF9; SN1 = 0xFA; SN2 = 0xFB; SN3 = 0xFC; SFR Page = 0x0F;
Bit
Name
Function
7:0
SERNUMn[7:0] Serial Number Bits.
The four serial number registers form a 32-bit serial number, with SN3 as the
most significant byte and SN0 as the least significant byte.
Rev. 1.2
91
C8051F55x/56x/57x
11. Memory Organization
The memory organization of the CIP-51 System Controller is similar to that of a standard 8051. There are
two separate memory spaces: program memory and data memory. Program and data memory share the
same address space but are accessed via different instruction types. The memory organization is shown in
Figure 11.1
PROGRAM/DATA MEMORY
(FLASH)
C8051F550/1/2/3
C8051F560/1/2/3/8/9
C8051F570/1
RESERVED
DATA MEMORY (RAM)
INTERNAL DATA ADDRESS SPACE
0xFF
0x80
0x7F
Upper 128 RAM
(Indirect Addressing
Only)
Special Function
Register's
(Direct Addressing Only)
(Direct and Indirect
Addressing)
0x7C00
0x7BFF
32 kB FLASH
(In-System
Programmable in 512
Byte Sectors)
0x30
0x2F
0x20
0x1F
0x00
Bit Addressable
Lower 128 RAM
(Direct and Indirect
Addressing)
General Purpose
Registers
EXTERNAL DATA ADDRESS SPACE
0xFFFF
0x0000
C8051F554/5/6/7
C8051F564/5/6/7
C8051F572/3/4/5
0x3FFF
Same 2048 bytes as
from 0x0000 to 0x07FF,
wrapped on 2048-byte
boundaries
0x8000
0x07FF
16 kB FLASH
XRAM
2K Bytes
(In-System
Programmable in 512
Byte Sectors)
(accessable using
MOVX instruction)
0x0000
0x0000
Figure 11.1. C8051F55x/56x/57x Memory Map
11.1. Program Memory
The CIP-51 core has a 64 kB program memory space. The C8051F55x/56x/57x devices implement 32 kB
or 16 kB of this program memory space as in-system, re-programmable Flash memory, organized in a contiguous block from addresses 0x0000 to 0x7FFF in 32 kB devices and addresses 0x0000 to 0x3FFF in
16 kB devices. The address 0x7BFF in 32 kB devices and 0x3FFF in 16 kB devices serves as the security
lock byte for the device. Addresses above 0x7BFF are reserved in the 32 kB devices.
Rev. 1.2
92
C8051F55x/56x/57x
C8051F550/1/2/3
C8051F560/1/2/3/8/9
C8051F570/1
0x7FFF
Reserved Area
Lock Byte
0x7BFF
0x7BFE
C8051F554/5/6/7
C8051F564/5/6/7
C8051F572/3/4/5
Lock Byte Page
0x7A00
Lock Byte
0x3FFF
0x3FFE
Lock Byte Page
Flash Memory Space
(32 kB Flash Device)
0x3E00
Flash Memory Space
(16 kB Flash Device)
FLASH memory organized in
512-byte pages
0x7C00
0x0000
0x0000
Figure 11.2. Flash Program Memory Map
11.1.1. MOVX Instruction and Program Memory
The MOVX instruction in an 8051 device is typically used to access external data memory. On the
C8051F55x/56x/57x devices, the MOVX instruction is normally used to read and write on-chip XRAM, but
can be re-configured to write and erase on-chip Flash memory space. MOVC instructions are always used
to read Flash memory, while MOVX write instructions are used to erase and write Flash. This Flash access
feature provides a mechanism for the C8051F55x/56x/57x to update program code and use the program
memory space for non-volatile data storage. Refer to Section “14. Flash Memory” on page 124 for further
details.
11.2. Data Memory
The C8051F55x/56x/57x devices include 2304 bytes of RAM data memory. 256 bytes of this memory is
mapped into the internal RAM space of the 8051. The other 2048 bytes of this memory is on-chip “external” memory. The data memory map is shown in Figure 11.1 for reference.
11.2.1. Internal RAM
There are 256 bytes of internal RAM mapped into the data memory space from 0x00 through 0xFF. The
lower 128 bytes of data memory are used for general purpose registers and scratch pad memory. Either
direct or indirect addressing may be used to access the lower 128 bytes of data memory. Locations 0x00
through 0x1F are addressable as four banks of general purpose registers, each bank consisting of eight
byte-wide registers. The next 16 bytes, locations 0x20 through 0x2F, may either be addressed as bytes or
as 128 bit locations accessible with the direct addressing mode.
The upper 128 bytes of data memory are accessible only by indirect addressing. This region occupies the
same address space as the Special Function Registers (SFR) but is physically separate from the SFR
space. The addressing mode used by an instruction when accessing locations above 0x7F determines
whether the CPU accesses the upper 128 bytes of data memory space or the SFRs. Instructions that use
direct addressing will access the SFR space. Instructions using indirect addressing above 0x7F access the
upper 128 bytes of data memory. Figure 11.1 illustrates the data memory organization of the
93
Rev. 1.2
C8051F55x/56x/57x
C8051F55x/56x/57x.
11.2.1.1. General Purpose Registers
The lower 32 bytes of data memory, locations 0x00 through 0x1F, may be addressed as four banks of general-purpose registers. Each bank consists of eight byte-wide registers designated R0 through R7. Only
one of these banks may be enabled at a time. Two bits in the program status word, RS0 (PSW.3) and RS1
(PSW.4), select the active register bank (see description of the PSW in SFR Definition 10.6). This allows
fast context switching when entering subroutines and interrupt service routines. Indirect addressing modes
use registers R0 and R1 as index registers.
11.2.1.2. Bit Addressable Locations
In addition to direct access to data memory organized as bytes, the sixteen data memory locations at 0x20
through 0x2F are also accessible as 128 individually addressable bits. Each bit has a bit address from
0x00 to 0x7F. Bit 0 of the byte at 0x20 has bit address 0x00 while bit7 of the byte at 0x20 has bit address
0x07. Bit 7 of the byte at 0x2F has bit address 0x7F. A bit access is distinguished from a full byte access by
the type of instruction used (bit source or destination operands as opposed to a byte source or destination).
The MCS-51™ assembly language allows an alternate notation for bit addressing of the form XX.B where
XX is the byte address and B is the bit position within the byte. For example, the instruction:
MOV
C, 22.3h
moves the Boolean value at 0x13 (bit 3 of the byte at location 0x22) into the Carry flag.
11.2.1.3. Stack
A programmer's stack can be located anywhere in the 256-byte data memory. The stack area is designated using the Stack Pointer (SP) SFR. The SP will point to the last location used. The next value pushed
on the stack is placed at SP+1 and then SP is incremented. A reset initializes the stack pointer to location
0x07. Therefore, the first value pushed on the stack is placed at location 0x08, which is also the first register (R0) of register bank 1. Thus, if more than one register bank is to be used, the SP should be initialized
to a location in the data memory not being used for data storage. The stack depth can extend up to
256 bytes.
Rev. 1.2
94
C8051F55x/56x/57x
12. Special Function Registers
The direct-access data memory locations from 0x80 to 0xFF constitute the special function registers
(SFRs). The SFRs provide control and data exchange with the C8051F55x/56x/57x's resources and
peripherals. The CIP-51 controller core duplicates the SFRs found in a typical 8051 implementation as well
as implementing additional SFRs used to configure and access the sub-systems unique to the
C8051F55x/56x/57x. This allows the addition of new functionality while retaining compatibility with the
MCS-51™ instruction set. Table 12.3 lists the SFRs implemented in the C8051F55x/56x/57x device family.
The SFR registers are accessed anytime the direct addressing mode is used to access memory locations
from 0x80 to 0xFF. SFRs with addresses ending in 0x0 or 0x8 (e.g., P0, TCON, SCON0, IE, etc.) are bitaddressable as well as byte-addressable. All other SFRs are byte-addressable only. Unoccupied
addresses in the SFR space are reserved for future use. Accessing unoccupied addresses in the SFR
space will have an indeterminate effect and should be avoided. Refer to the corresponding pages of the
data sheet, as indicated in Table 12.3, for a detailed description of each register.
12.1. SFR Paging
The CIP-51 features SFR paging, allowing the device to map many SFRs into the 0x80 to 0xFF memory
address space. The SFR memory space has 256 pages. In this way, each memory location from 0x80 to
0xFF can access up to 256 SFRs. The C8051F55x/56x/57x family of devices utilizes three SFR pages:
0x00, 0x0C, and 0x0F. SFR pages are selected using the Special Function Register Page Selection register, SFRPAGE (see SFR Definition 11.3). The procedure for reading and writing an SFR is as follows:
1. Select the appropriate SFR page number using the SFRPAGE register.
2. Use direct accessing mode to read or write the special function register (MOV instruction).
12.2. Interrupts and SFR Paging
When an interrupt occurs, the SFR Page Register will automatically switch to the SFR page containing the
flag bit that caused the interrupt. The automatic SFR Page switch function conveniently removes the burden of switching SFR pages from the interrupt service routine. Upon execution of the RETI instruction, the
SFR page is automatically restored to the SFR Page in use prior to the interrupt. This is accomplished via
a three-byte SFR Page Stack. The top byte of the stack is SFRPAGE, the current SFR Page. The second
byte of the SFR Page Stack is SFRNEXT. The third, or bottom byte of the SFR Page Stack is SFRLAST.
Upon an interrupt, the current SFRPAGE value is pushed to the SFRNEXT byte, and the value of
SFRNEXT is pushed to SFRLAST. Hardware then loads SFRPAGE with the SFR Page containing the flag
bit associated with the interrupt. On a return from interrupt, the SFR Page Stack is popped resulting in the
value of SFRNEXT returning to the SFRPAGE register, thereby restoring the SFR page context without
software intervention. The value in SFRLAST (0x00 if there is no SFR Page value in the bottom of the
stack) of the stack is placed in SFRNEXT register. If desired, the values stored in SFRNEXT and SFRLAST may be modified during an interrupt, enabling the CPU to return to a different SFR Page upon execution of the RETI instruction (on interrupt exit). Modifying registers in the SFR Page Stack does not cause
a push or pop of the stack. Only interrupt calls and returns will cause push/pop operations on the SFR
Page Stack.
On the C8051F55x/56x/57x devices, vectoring to an interrupt will switch SFRPAGE to page 0x00, except
for the CAN0 interrupt which will switch SFRPAGE to page 0x0C.
Rev. 1.2
95
C8051F55x/56x/57x
SFRPGCN Bit
Interrupt
Logic
SFRPAGE
CIP-51
SFRNEXT
SFRLAST
Figure 12.1. SFR Page Stack
Automatic hardware switching of the SFR Page on interrupts may be enabled or disabled as desired using
the SFR Automatic Page Control Enable Bit located in the SFR Page Control Register (SFR0CN). This
function defaults to “enabled” upon reset. In this way, the autoswitching function will be enabled unless disabled in software.
A summary of the SFR locations (address and SFR page) are provided in Table 12.3 in the form of an SFR
memory map. Each memory location in the map has an SFR page row, denoting the page in which that
SFR resides. Certain SFRs are accessible from ALL SFR pages, and are denoted by the “(ALL PAGES)”
designation. For example, the Port I/O registers P0, P1, P2, and P3 all have the “(ALL PAGES)” designation, indicating these SFRs are accessible from all SFR pages regardless of the SFRPAGE register value.
96
Rev. 1.2
C8051F55x/56x/57x
12.3. SFR Page Stack Example
The following is an example that shows the operation of the SFR Page Stack during interrupts. In this
example, the SFR Control register is left in the default enabled state (i.e., SFRPGEN = 1), and the CIP-51
is executing in-line code that is writing values to SPI Data Register (SFR “SPI0DAT”, located at address
0xA3 on SFR Page 0x00). The device is also using the CAN peripheral (CAN0) and the Programmable
Counter Array (PCA0) peripheral to generate a PWM output. The PCA is timing a critical control function in
its interrupt service and so its associated ISR that is set to high priority. At this point, the SFR page is set to
access the SPI0DAT SFR (SFRPAGE = 0x00). See Figure 12.2.
SFR Page
Stack SFR's
0x0
SFRPAGE
(SPI0DAT)
SFRNEXT
SFRLAST
Figure 12.2. SFR Page Stack While Using SFR Page 0x0 To Access SPI0DAT
Rev. 1.2
97
C8051F55x/56x/57x
While CIP-51 executes in-line code (writing values to SPI0DAT in this example), the CAN0 Interrupt
occurs. The CIP-51 vectors to the CAN0 ISR and pushes the current SFR Page value (SFR Page 0x00)
into SFRNEXT in the SFR Page Stack. The SFR page needed to access CAN’s SFRs is then automatically
placed in the SFRPAGE register (SFR Page 0x0C). SFRPAGE is considered the “top” of the SFR Page
Stack. Software can now access the CAN0 SFRs. Software may switch to any SFR Page by writing a new
value to the SFRPAGE register at any time during the CAN0 ISR to access SFRs that are not on SFR
Page 0x0C. See Figure 12.3.
SFR Page 0xC
Automatically
pushed on stack in
SFRPAGE on CAN0
interrupt
0xC
SFRPAGE
SFRPAGE
pushed to
SFRNEXT
(CAN0)
0x0
SFRNEXT
(SPI0DAT)
SFRLAST
Figure 12.3. SFR Page Stack After CAN0 Interrupt Occurs
98
Rev. 1.2
C8051F55x/56x/57x
While in the CAN0 ISR, a PCA interrupt occurs. Recall the PCA interrupt is configured as a high priority
interrupt, while the CAN0 interrupt is configured as a low priority interrupt. Thus, the CIP-51 will now vector
to the high priority PCA ISR. Upon doing so, the CIP-51 will automatically place the SFR page needed to
access the PCA’s special function registers into the SFRPAGE register, SFR Page 0x00. The value that
was in the SFRPAGE register before the PCA interrupt (SFR Page 0x0C for CAN0) is pushed down the
stack into SFRNEXT. Likewise, the value that was in the SFRNEXT register before the PCA interrupt (in
this case SFR Page 0x00 for SPI0DAT) is pushed down to the SFRLAST register, the “bottom” of the
stack. Note that a value stored in SFRLAST (via a previous software write to the SFRLAST register) will be
overwritten. See Figure 12.4.
SFR Page 0x0
Automatically
pushed on stack in
SFRPAGE on PCA
interrupt
0x0
SFRPAGE
SFRPAGE
pushed to
SFRNEXT
(PCA)
0xC
SFRNEXT
SFRNEXT
pushed to
SFRLAST
(CAN0)
0x0
SFRLAST
(SPI0DAT)
Figure 12.4. SFR Page Stack Upon PCA Interrupt Occurring During a CAN0 ISR
Rev. 1.2
99
C8051F55x/56x/57x
On exit from the PCA interrupt service routine, the CIP-51 will return to the CAN0 ISR. On execution of the
RETI instruction, SFR Page 0x00 used to access the PCA registers will be automatically popped off of the
SFR Page Stack, and the contents of the SFRNEXT register will be moved to the SFRPAGE register. Software in the CAN0 ISR can continue to access SFRs as it did prior to the PCA interrupt. Likewise, the contents of SFRLAST are moved to the SFRNEXT register. Recall this was the SFR Page value 0x00 being
used to access SPI0DAT before the CAN0 interrupt occurred. See Figure 12.5.
SFR Page 0x0
Automatically
popped off of the
stack on return from
interrupt
0xC
SFRPAGE
SFRNEXT
popped to
SFRPAGE
(CAN0)
0x0
SFRNEXT
SFRLAST
popped to
SFRNEXT
(SPI0DAT)
SFRLAST
Figure 12.5. SFR Page Stack Upon Return From PCA Interrupt
100
Rev. 1.2
C8051F55x/56x/57x
On the execution of the RETI instruction in the CAN0 ISR, the value in SFRPAGE register is overwritten
with the contents of SFRNEXT. The CIP-51 may now access the SPI0DAT register as it did prior to the
interrupts occurring. See Figure 12.6.
SFR Page 0xC
Automatically
popped off of the
stack on return from
interrupt
0x0
SFRPAGE
SFRNEXT
popped to
SFRPAGE
(SPI0DAT)
SFRNEXT
SFRLAST
Figure 12.6. SFR Page Stack Upon Return From CAN0 Interrupt
In the example above, all three bytes in the SFR Page Stack are accessible via the SFRPAGE, SFRNEXT,
and SFRLAST special function registers. If the stack is altered while servicing an interrupt, it is possible to
return to a different SFR Page upon interrupt exit than selected prior to the interrupt call. Direct access to
the SFR Page stack can be useful to enable real-time operating systems to control and manage context
switching between multiple tasks.
Push operations on the SFR Page Stack only occur on interrupt service, and pop operations only occur on
interrupt exit (execution on the RETI instruction). The automatic switching of the SFRPAGE and operation
of the SFR Page Stack as described above can be disabled in software by clearing the SFR Automatic
Page Enable Bit (SFRPGEN) in the SFR Page Control Register (SFR0CN). See SFR Definition 12.1.
Rev. 1.2
101
C8051F55x/56x/57x
SFR Definition 12.1. SFR0CN: SFR Page Control
Bit
7
6
5
4
3
2
1
0
SFRPGEN
Name
Type
R
R
R
R
R
R
R
R/W
Reset
0
0
0
0
0
0
0
1
SFR Address = 0x84; SFR Page = 0x0F
Bit
Name
7:1
0
Function
Unused
Read = 0000000b; Write = Don’t Care
SFRPGEN SFR Automatic Page Control Enable.
Upon interrupt, the C8051 Core will vector to the specified interrupt service routine
and automatically switch the SFR page to the corresponding peripheral or function’s
SFR page. This bit is used to control this autopaging function.
0: SFR Automatic Paging disabled. The C8051 core will not automatically change to
the appropriate SFR page (i.e., the SFR page that contains the SFRs for the peripheral/function that was the source of the interrupt).
1: SFR Automatic Paging enabled. Upon interrupt, the C8051 will switch the SFR
page to the page that contains the SFRs for the peripheral or function that is the
source of the interrupt.
102
Rev. 1.2
C8051F55x/56x/57x
SFR Definition 12.2. SFRPAGE: SFR Page
Bit
7
6
5
4
3
Name
SFRPAGE[7:0]
Type
R/W
Reset
0
0
0
0
SFR Address = 0xA7; SFR Page = All Pages
Bit
Name
7:0
SFRPAGE[7:0]
0
2
1
0
0
0
0
Function
SFR Page Bits.
Represents the SFR Page the C8051 core uses when reading or modifying
SFRs.
Write: Sets the SFR Page.
Read: Byte is the SFR page the C8051 core is using.
When enabled in the SFR Page Control Register (SFR0CN), the C8051 core will
automatically switch to the SFR Page that contains the SFRs of the corresponding peripheral/function that caused the interrupt, and return to the previous SFR
page upon return from interrupt (unless SFR Stack was altered before a returning from the interrupt). SFRPAGE is the top byte of the SFR Page Stack, and
push/pop events of this stack are caused by interrupts (and not by reading/writing to the SFRPAGE register)
Rev. 1.2
103
C8051F55x/56x/57x
SFR Definition 12.3. SFRNEXT: SFR Next
Bit
7
6
5
4
3
Name
SFRNEXT[7:0]
Type
R/W
Reset
0
0
0
0
SFR Address = 0x85; SFR Page = All Pages
Bit
Name
7:0
SFRNEXT[7:0]
0
2
1
0
0
0
0
Function
SFR Page Bits.
This is the value that will go to the SFR Page register upon a return from interrupt.
Write: Sets the SFR Page contained in the second byte of the SFR Stack. This
will cause the SFRPAGE SFR to have this SFR page value upon a return from
interrupt.
Read: Returns the value of the SFR page contained in the second byte of the
SFR stack.
SFR page context is retained upon interrupts/return from interrupts in a 3 byte
SFR Page Stack: SFRPAGE is the first entry, SFRNEXT is the second, and
SFRLAST is the third entry. The SFR stack bytes may be used alter the context
in the SFR Page Stack, and will not cause the stack to “push” or “pop”. Only
interrupts and return from interrupts cause pushes and pops of the SFR Page
Stack.
104
Rev. 1.2
C8051F55x/56x/57x
SFR Definition 12.4. SFRLAST: SFR Last
Bit
7
6
5
4
3
Name
SFRLAST[7:0]
Type
R/W
Reset
0
0
0
SFR Address = 0xA7; SFR Page = All Pages
Bit
Name
7:0
SFRLAST[7:0]
0
0
2
1
0
0
0
0
Function
SFR Page Stack Bits.
This is the value that will go to the SFRNEXT register upon a return from interrupt.
Write: Sets the SFR Page in the last entry of the SFR Stack. This will cause the
SFRNEXT SFR to have this SFR page value upon a return from interrupt.
Read: Returns the value of the SFR page contained in the last entry of the SFR
stack.
SFR page context is retained upon interrupts/return from interrupts in a 3 byte
SFR Page Stack: SFRPAGE is the first entry, SFRNEXT is the second, and
SFRLAST is the third entry. The SFR stack bytes may be used alter the context
in the SFR Page Stack, and will not cause the stack to “push” or “pop”. Only
interrupts and return from interrupts cause pushes and pops of the SFR Page
Stack.
Rev. 1.2
105
C8051F55x/56x/57x
Page
Address
Table 12.1. Special Function Register (SFR) Memory Map for Pages 0x00 and 0x0F
0(8)
1(9)
2(A)
3(B)
4(C)
5(D)
6(E)
7(F)
F8 0 SPI0CN
PCA0L
PCA0H PCA0CPL0 PCA0CPH0 PCACPL4 PCACPH4 VDM0CN
F
SN0
SN1
SN2
SN3
F0 0
B
P0MAT
P0MASK
P1MAT
P1MASK
EIP1
EIP2
F (All Pages) P0MDIN
P1MDIN
P2MDIN
P3MDIN
EIP1
EIP2
E8 0 ADC0CN PCA0CPL1 PCA0CPH1 PCA0CPL2 PCA0CPH2 PCA0CPL3 PCA0CPL3 RSTSRC
F
E0 0
ACC
EIE1
EIE2
F (All Pages)
XBR0
XBR1
CCH0CN
IT01CF
(All Pages) (All Pages)
D8 0 PCA0CN PCA0MD PCA0CPM0 PCA0CPM1 PCA0CPM2 PCA0CPM3 PCA0CPM4 PCA0CPM5
F
PCA0PWM
D0 0
PSW
REF0CN LIN0DATA LIN0ADDR
F (All Pages)
P0SKIP
P1SKIP
P2SKIP
P3SKIP
C8 0 TMR2CN REG0CN TMR2RLL TMR2RLH
TMR2L
TMR2H PCA0CPL5 PCA0CPH5
F
LIN0CF
C0 0 SMB0CN SMB0CF SMB0DAT ADC0GTL ADC0GTH ADC0LTL ADC0LTH
F
XBR2
B8 0
IP
ADC0TK
ADC0MX
ADC0CF
ADC0L
ADC0H
F (All Pages)
B0 0
P3
P2MAT
P2MASK
P4
FLSCL
FLKEY
F (All Pages)
EMI0CF
(All Pages) (All Pages) (All Pages)
A8 0
IE
SMOD0
EMI0CN
P3MAT
P3MASK
F (All Pages)
EMI0TC
SBCON0
SBRLL0
SBRLH0 P3MDOUT P4MDOUT
A0 0
P2
SPI0CFG SPI0CKR SPI0DAT
SFRPAGE
F (All Pages) OSCICN OSCICRS
P0MDOUT P1MDOUT P2MDOUT (All Pages)
98 0 SCON0
SBUF0
CPT0CN
CPT0MD
CPT0MX
CPT1CN
CPT1MD
CPT1MX
F
OSCIFIN OSCXCN
90 0
P1
TMR3CN TMR3RLL TMR3RLH
TMR3L
TMR3H
F (All Pages)
CLKMUL
88 0 TCON
TMOD
TL0
TL1
TH0
TH1
CKCON
PSCTL
F (All Pages) (All Pages) (All Pages) (All Pages) (All Pages) (All Pages) (All Pages) CLKSEL
80 0
P0
SP
DPL
DPH
SFRNEXT SFRLAST
PCON
F (All Pages) (All Pages) (All Pages) (All Pages) SFR0CN (All Pages) (All Pages) (All Pages)
0(8)
1(9)
2(A)
3(B)
4(C)
5(D)
6(E)
7(F)
(bit addressable)
106
Rev. 1.2
C8051F55x/56x/57x
Table 12.2. Special Function Register (SFR) Memory Map for Page 0x0C
0(8)
1(9)
F8
F0
B
(All Pages)
E8
E0
ACC
(All Pages)
3(B)
4(C)
5(D)
CAN0IF2A2L
CAN0IF2A2H
6(E)
CAN0IF2M1L
CAN0IF2M1H CAN0IF2M2L
CAN0IF2DA1H
CAN0IF2A1L
CAN0IF2A1H
EIE1
(All Pages)
EIE2
(All Pages)
CAN0IF2CRL
CAN0IF2CRH
CAN0IF1MCL CAN0IF1MCH CAN0IF1DA1L CAN0IF1DA1H CAN0IF1DA2L
CAN0IF1DA2H
CAN0IF1A1L
CAN0IF2M2H
CAN0IF1DB1L CAN0IF1DB1H CAN0IF1DB2L CAN0IF1DB2H
PSW
(All Pages)
C8
CAN0IF1A1H
CAN0IF1A2L
CAN0IF1A2H
CAN0IF2MCL
CAN0IF2MCH
CAN0IF1CML CAN0IF1CMH CAN0IF1M1L
CAN0IF1M1H
CAN0IF1M2L
CAN0IF1M2H
CAN0MV2H
CAN0IF1CRL
CAN0IF1CRH
P4
(All Pages)
FLSCL
(All Pages)
FLKEY
(All Pages)
CAN0IP1L
CAN0IP1H
C0
CAN0CN
B8
IP
(All Pages)
CAN0MV1L
CAN0MV1H
B0
P3
(All Pages)
CAN0IP2L
CAN0IP2H
A8
IE
(All Pages)
CAN0ND1L
CAN0ND1H
CAN0ND2L
CAN0ND2H
A0
P2
CAN0BRPE
(All Pages)
CAN0TR1L
CAN0TR1H
CAN0TR2L
CAN0TR2H
98
SCON0
(All Pages)
CAN0BTL
CAN0BTH
CAN0IIDL
CAN0IIDH
90
P1
(All Pages)
CAN0CFG
88
TCON
TMOD
(All Pages) (All Pages)
TL0
(All Pages)
TL1
(All Pages)
80
P0
SP
(All Pages) (All Pages)
DPL
(All Pages)
DPH
(All Pages)
2(A)
3(B)
0(8)
1(9)
7(F)
CAN0IF2DB2H
CAN0IF2DA1L
CAN0IF2CML CAN0IF2CMH
D8
D0
2(A)
CAN0IF2DA2L CAN0IF2DA2H CAN0IF2DB1L CAN0IF2DB1H CAN0IF2DB2L
CAN0MV2L
CAN0STAT
TH0
(All Pages)
4(C)
SFRPAGE
(All Pages)
CAN0TST
CAN0ERRL
CAN0ERRH
TH1
(All Pages)
CKCON
(All Pages)
SFRNEXT
(All Pages)
SFRLAST
(All Pages)
PCON
(All Pages)
5(D)
6(E)
7(F)
(bit addressable)
Rev. 1.2
107
C8051F55x/56x/57x
Table 12.3. Special Function Registers
SFRs are listed in alphabetical order. All undefined SFR locations are reserved
Register
Address
Description
Page
ACC
0xE0
Accumulator
89
ADC0CF
0xBC
ADC0 Configuration
58
ADC0CN
0xE8
ADC0 Control
60
ADC0GTH
0xC4
ADC0 Greater-Than Compare High
62
ADC0GTL
0xC3
ADC0 Greater-Than Compare Low
62
ADC0H
0xBE
ADC0 High
59
ADC0L
0xBD
ADC0 Low
59
ADC0LTH
0xC6
ADC0 Less-Than Compare Word High
63
ADC0LTL
0xC5
ADC0 Less-Than Compare Word Low
63
ADC0MX
0xBB
ADC0 Mux Configuration
66
ADC0TK
0xBA
ADC0 Tracking Mode Select
61
B
0xF0
B Register
89
CCH0CN
0xE3
Cache Control
134
CKCON
0x8E
Clock Control
260
CLKMUL
0x97
Clock Multiplier
163
CLKSEL
0x8F
Clock Select
158
CPT0CN
0x9A
Comparator0 Control
72
CPT0MD
0x9B
Comparator0 Mode Selection
73
CPT0MX
0x9C
Comparator0 MUX Selection
77
CPT1CN
0x9D
Comparator1 Control
72
CPT1MD
0x9E
Comparator1 Mode Selection
73
CPT1MX
0x9F
Comparator1 MUX Selection
77
DPH
0x83
Data Pointer High
88
DPL
0x82
Data Pointer Low
88
EIE1
0xE6
Extended Interrupt Enable 1
118
EIE2
0xE7
Extended Interrupt Enable 2
118
EIP1
0xF6
Extended Interrupt Priority 1
119
EIP2
0xF7
Extended Interrupt Priority 2
120
EMI0CF
0xB2
External Memory Interface Configuration
148
EMI0CN
0xAA
External Memory Interface Control
147
EMI0TC
0xAA
External Memory Interface Timing Control
152
FLKEY
0xB7
Flash Lock and Key
132
FLSCL
0xB6
Flash Scale
133
IE
0xA8
Interrupt Enable
116
IP
0xB8
Interrupt Priority
117
108
Rev. 1.2
C8051F55x/56x/57x
Table 12.3. Special Function Registers (Continued)
SFRs are listed in alphabetical order. All undefined SFR locations are reserved
Register
Address
Description
Page
IT01CF
0xE4
INT0/INT1 Configuration
123
LIN0ADR
0xD3
LIN0 Address
200
LIN0CF
0xC9
LIN0 Configuration
200
LIN0DAT
0xD2
LIN0 Data
201
OSCICN
0xA1
Internal Oscillator Control
160
OSCICRS
0xA2
Internal Oscillator Coarse Control
161
OSCIFIN
0x9E
Internal Oscillator Fine Calibration
161
OSCXCN
0x9F
External Oscillator Control
165
P0
0x80
Port 0 Latch
183
P0MASK
0xF2
Port 0 Mask Configuration
179
P0MAT
0xF1
Port 0 Match Configuration
179
P0MDIN
0xF1
Port 0 Input Mode Configuration
184
P0MDOUT
0xA4
Port 0 Output Mode Configuration
184
P0SKIP
0xD4
Port 0 Skip
185
P1
0x90
Port 1 Latch
185
P1MASK
0xF4
Port 1 Mask Configuration
180
P1MAT
0xF3
Port 1 Match Configuration
180
P1MDIN
0xF2
Port 1 Input Mode Configuration
186
P1MDOUT
0xA5
Port 1 Output Mode Configuration
186
P1SKIP
0xD5
Port 1 Skip
187
P2
0xA0
Port 2 Latch
187
P2MASK
0xB2
Port 2 Mask Configuration
181
P2MAT
0xB1
Port 2 Match Configuration
181
P2MDIN
0xF3
Port 2 Input Mode Configuration
188
P2MDOUT
0xA6
Port 2 Output Mode Configuration
188
P2SKIP
0xD6
Port 2 Skip
189
P3
0xB0
Port 3 Latch
189
P3MASK
0xAF
Port 3 Mask Configuration
182
P3MAT
0xAE
Port 3 Match Configuration
182
P3MDIN
0xF4
Port 3 Input Mode Configuration
190
P3MDOUT
0xAE
Port 3 Output Mode Configuration
190
P3SKIP
0xD7
Port 3 Skip
191
P4
0xB5
Port 4 Latch
191
P4MDOUT
0xAF
Port 4 Output Mode Configuration
192
PCA0CN
0xD8
PCA Control
294
PCA0CPH0
0xFC
PCA Capture 0 High
299
Rev. 1.2
109
C8051F55x/56x/57x
Table 12.3. Special Function Registers (Continued)
SFRs are listed in alphabetical order. All undefined SFR locations are reserved
Register
Address
Description
Page
PCA0CPH1
0xEA
PCA Capture 1 High
299
PCA0CPH2
0xEC
PCA Capture 2 High
299
PCA0CPH3
0xEE
PCA Capture 3 High
299
PCA0CPH4
0xFE
PCA Capture 4 High
299
PCA0CPH5
0xCF
PCA Capture 5 High
299
PCA0CPL0
0xFB
PCA Capture 0 Low
299
PCA0CPL1
0xE9
PCA Capture 1 Low
299
PCA0CPL2
0xEB
PCA Capture 2 Low
299
PCA0CPL3
0xED
PCA Capture 3 Low
299
PCA0CPL4
0xFD
PCA Capture 4 Low
299
PCA0CPL5
0xCE
PCA Capture 5 Low
299
PCA0CPM0
0xDA
PCA Module 0 Mode Register
297
PCA0CPM1
0xDB
PCA Module 1 Mode Register
297
PCA0CPM2
0xDC
PCA Module 2 Mode Register
297
PCA0CPM3
0xDD
PCA Module 3 Mode Register
297
PCA0CPM4
0xDE
PCA Module 4 Mode Register
297
PCA0CPM5
0xDF
PCA Module 5 Mode Register
297
PCA0H
0xFA
PCA Counter High
298
PCA0L
0xF9
PCA Counter Low
298
PCA0MD
0xD9
PCA Mode
295
PCA0PWM
0xD9
PCA PWM Configuration
296
PCON
0x87
Power Control
137
PSCTL
0x8F
Program Store R/W Control
131
PSW
0xD0
Program Status Word
90
REF0CN
0xD1
Voltage Reference Control
69
REG0CN
0xC9
Voltage Regulator Control
80
RSTSRC
0xEF
Reset Source Configuration/Status
143
SBCON0
0xAB
UART0 Baud Rate Generator Control
244
SBRLH0
0xAD
UART0 Baud Rate Reload High Byte
245
SBRLL0
0xAC
UART0 Baud Rate Reload Low Byte
245
SBUF0
0x99
UART0 Data Buffer
244
SCON0
0x98
UART0 Control
241
SFR0CN
0x84
SFR Page Control
102
SFRLAST
0x86
SFR Stack Last Page
105
SFRNEXT
0x85
SFR Stack Next Page
104
SFRPAGE
0xA7
SFR Page Select
103
110
Rev. 1.2
C8051F55x/56x/57x
Table 12.3. Special Function Registers (Continued)
SFRs are listed in alphabetical order. All undefined SFR locations are reserved
Register
Address
Description
Page
SMB0CF
0xC1
SMBus0 Configuration
224
SMB0CN
0xC0
SMBus0 Control
226
SMB0DAT
0xC2
SMBus0 Data
228
SMOD0
0xA9
UART0 Mode
243
SN0
0xF9
Serial Number 0
91
SN1
0xFA
Serial Number 1
91
SN2
0xFB
Serial Number 2
91
SN3
0xFC
Serial Number 3
91
SP
0x81
Stack Pointer
89
SPI0CFG
0xA1
SPI0 Configuration
253
SPI0CKR
0xA2
SPI0 Clock Rate Control
255
SPI0CN
0xF8
SPI0 Control
254
SPI0DAT
0xA3
SPI0 Data
255
TCON
0x88
Timer/Counter Control
265
TH0
0x8C
Timer/Counter 0 High
268
TH1
0x8D
Timer/Counter 1 High
268
TL0
0x8A
Timer/Counter 0 Low
267
TL1
0x8B
Timer/Counter 1 Low
267
TMOD
0x89
Timer/Counter Mode
266
TMR2CN
0xC8
Timer/Counter 2 Control
272
TMR2H
0xCD
Timer/Counter 2 High
274
TMR2L
0xCC
Timer/Counter 2 Low
274
TMR2RLH
0xCB
Timer/Counter 2 Reload High
273
TMR2RLL
0xCA
Timer/Counter 2 Reload Low
273
TMR3CN
0x91
Timer/Counter 3 Control
278
TMR3H
0x95
Timer/Counter 3 High
280
TMR3L
0x94
Timer/Counter 3 Low
280
TMR3RLH
0x93
Timer/Counter 3 Reload High
279
TMR3RLL
0x92
Timer/Counter 3 Reload Low
279
VDM0CN
0xFF
VDD Monitor Control
141
XBR0
0xE1
Port I/O Crossbar Control 0
176
XBR1
0xE2
Port I/O Crossbar Control 1
177
XBR2
0xC7
Port I/O Crossbar Control 2
178
Rev. 1.2
111
C8051F55x/56x/57x
13. Interrupts
The C8051F55x/56x/57x devices include an extended interrupt system supporting a total of 18 interrupt
sources with two priority levels. The allocation of interrupt sources between on-chip peripherals and external inputs pins varies according to the specific version of the device. Each interrupt source has one or
more associated interrupt-pending flag(s) located in an SFR. When a peripheral or external source meets
a valid interrupt condition, the associated interrupt-pending flag is set to logic 1.
If interrupts are enabled for the source, an interrupt request is generated when the interrupt-pending flag is
set. As soon as execution of the current instruction is complete, the CPU generates an LCALL to a predetermined address to begin execution of an interrupt service routine (ISR). Each ISR must end with an RETI
instruction, which returns program execution to the next instruction that would have been executed if the
interrupt request had not occurred. If interrupts are not enabled, the interrupt-pending flag is ignored by the
hardware and program execution continues as normal. (The interrupt-pending flag is set to logic 1 regardless of the interrupt's enable/disable state.)
Each interrupt source can be individually enabled or disabled through the use of an associated interrupt
enable bit in an SFR (IE, EIE1, or EIE2). However, interrupts must first be globally enabled by setting the
EA bit (IE.7) to logic 1 before the individual interrupt enables are recognized. Setting the EA bit to logic 0
disables all interrupt sources regardless of the individual interrupt-enable settings.
Note: Any instruction that clears a bit to disable an interrupt should be immediately followed by an instruction that has
two or more opcode bytes. Using EA (global interrupt enable) as an example:
// in 'C':
EA = 0; // clear EA bit.
EA = 0; // this is a dummy instruction with two-byte opcode.
; in assembly:
CLR EA ; clear EA bit.
CLR EA ; this is a dummy instruction with two-byte opcode.
For example, if an interrupt is posted during the execution phase of a "CLR EA" opcode (or any instruction
which clears a bit to disable an interrupt source), and the instruction is followed by a single-cycle instruction, the interrupt may be taken. However, a read of the enable bit will return a 0 inside the interrupt service
routine. When the bit-clearing opcode is followed by a multi-cycle instruction, the interrupt will not be taken.
Some interrupt-pending flags are automatically cleared by the hardware when the CPU vectors to the ISR.
However, most are not cleared by the hardware and must be cleared by software before returning from the
ISR. If an interrupt-pending flag remains set after the CPU completes the return-from-interrupt (RETI)
instruction, a new interrupt request will be generated immediately and the CPU will re-enter the ISR after
the completion of the next instruction.
13.1. MCU Interrupt Sources and Vectors
The C8051F55x/56x/57x MCUs support 18 interrupt sources. Software can simulate an interrupt by setting
any interrupt-pending flag to logic 1. If interrupts are enabled for the flag, an interrupt request will be generated and the CPU will vector to the ISR address associated with the interrupt-pending flag. MCU interrupt
sources, associated vector addresses, priority order and control bits are summarized in Table 13.1. Refer
to the datasheet section associated with a particular on-chip peripheral for information regarding valid
interrupt conditions for the peripheral and the behavior of its interrupt-pending flag(s).
Rev. 1.2
112
C8051F55x/56x/57x
13.1.1. Interrupt Priorities
Each interrupt source can be individually programmed to one of two priority levels: low or high. A low priority interrupt service routine can be preempted by a high priority interrupt. A high priority interrupt cannot be
preempted. Each interrupt has an associated interrupt priority bit in an SFR (IE, EIP1, or EIP2) used to
configure its priority level. Low priority is the default. If two interrupts are recognized simultaneously, the
interrupt with the higher priority is serviced first. If both interrupts have the same priority level, a fixed priority order is used to arbitrate, given in Table 13.1.
13.1.2. Interrupt Latency
Interrupt response time depends on the state of the CPU when the interrupt occurs. Pending interrupts are
sampled and priority decoded each system clock cycle. Therefore, the fastest possible response time is 5
system clock cycles: 1 clock cycle to detect the interrupt and 4 clock cycles to complete the LCALL to the
ISR. If an interrupt is pending when a RETI is executed, a single instruction is executed before an LCALL
is made to service the pending interrupt. Therefore, the maximum response time for an interrupt (when no
other interrupt is currently being serviced or the new interrupt is of greater priority) occurs when the CPU is
performing an RETI instruction followed by a DIV as the next instruction. In this case, the response time is
18 system clock cycles: 1 clock cycle to detect the interrupt, 5 clock cycles to execute the RETI, 8 clock
cycles to complete the DIV instruction and 4 clock cycles to execute the LCALL to the ISR. If the CPU is
executing an ISR for an interrupt with equal or higher priority, the new interrupt will not be serviced until the
current ISR completes, including the RETI and following instruction.
113
Rev. 1.2
C8051F55x/56x/57x
Interrupt
Vector
Priority
Order
Pending Flag
Reset
0x0000
Top
None
External Interrupt 0
(INT0)
Timer 0 Overflow
External Interrupt 1
(INT1)
Timer 1 Overflow
UART0
0x0003
0
IE0 (TCON.1)
N/A N/A Always
Always
Enabled
Highest
Y
Y
EX0 (IE.0) PX0 (IP.0)
0x000B
0x0013
1
2
TF0 (TCON.5)
IE1 (TCON.3)
Y
Y
Y
Y
ET0 (IE.1) PT0 (IP.1)
EX1 (IE.2) PX1 (IP.2)
0x001B
0x0023
3
4
Y
Y
Y
N
ET1 (IE.3) PT1 (IP.3)
ES0 (IE.4) PS0 (IP.4)
Timer 2 Overflow
0x002B
5
Y
N
ET2 (IE.5) PT2 (IP.5)
SPI0
0x0033
6
Y
N
ESPI0
(IE.6)
PSPI0
(IP.6)
SMB0
0x003B
7
TF1 (TCON.7)
RI0 (SCON0.0)
TI0 (SCON0.1)
TF2H (TMR2CN.7)
TF2L (TMR2CN.6)
SPIF (SPI0CN.7)
WCOL (SPI0CN.6)
MODF (SPI0CN.5)
RXOVRN (SPI0CN.4)
SI (SMB0CN.0)
Y
N
ADC0 Window Compare
ADC0 Conversion
Complete
Programmable
Counter Array
0x0043
8
Y
N
0x004B
9
Y
N
0x0053
10
Y
N
PSMB0
(EIP1.0)
PWADC0
(EIP1.1)
PADC0
(EIP1.2)
PPCA0
(EIP1.3)
Comparator0
0x005B
11
N
N
Comparator1
0x0063
12
Timer 3 Overflow
0x006B
13
LIN0
0x0073
14
CF (PCA0CN.7)
CCFn (PCA0CN.n)
COVF (PCA0PWM.6)
CP0FIF (CPT0CN.4)
CP0RIF (CPT0CN.5)
CP1FIF (CPT1CN.4)
CP1RIF (CPT1CN.5)
TF3H (TMR3CN.7)
TF3L (TMR3CN.6)
LIN0INT (LINST.3)
ESMB0
(EIE1.0)
EWADC0
(EIE1.1)
EADC0
(EIE1.2)
EPCA0
(EIE1.3)
Voltage Regulator
Dropout
CAN0
0x007B
15
N/A
0x0083
16
Port Match
0x008B
17
CAN0INT
(CAN0CN.7)
None
AD0WINT
(ADC0CN.3)
AD0INT (ADC0CN.5)
Cleared by HW?
Interrupt Source
Bit addressable?
Table 13.1. Interrupt Summary
Enable
Flag
ECP0
(EIE1.4)
N
N
ECP1
(EIE1.5)
N
N
ET3
(EIE1.6)
N
N* ELIN0
(EIE1.7)
N/A N/A EREG0
(EIE2.0)
N
Y
ECAN0
(EIE2.1)
N/A N/A EMAT
(EIE2.2)
Priority
Control
PCP0
(EIP1.4)
PCP1
(EIP1.5)
PT3
(EIP1.6)
PLIN0
(EIP1.7)
PREG0
(EIP2.0)
PCAN0
(EIP2.1)
PMAT
(EIP2.2)
*Note: The LIN0INT bit is cleared by setting RSTINT (LINCTRL.3)
Rev. 1.2
114
C8051F55x/56x/57x
13.2. Interrupt Register Descriptions
The SFRs used to enable the interrupt sources and set their priority level are described in this section.
Refer to the data sheet section associated with a particular on-chip peripheral for information regarding
valid interrupt conditions for the peripheral and the behavior of its interrupt-pending flag(s).
115
Rev. 1.2
C8051F55x/56x/57x
SFR Definition 13.1. IE: Interrupt Enable
Bit
7
6
5
4
3
2
1
0
Name
EA
ESPI0
ET2
ES0
ET1
EX1
ET0
EX0
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Address = 0xA8; Bit-Addressable; SFR Page = All Pages
Bit
Name
Function
7
EA
6
ESPI0
5
ET2
Enable Timer 2 Interrupt.
This bit sets the masking of the Timer 2 interrupt.
0: Disable Timer 2 interrupt.
1: Enable interrupt requests generated by the TF2L or TF2H flags.
4
ES0
Enable UART0 Interrupt.
This bit sets the masking of the UART0 interrupt.
0: Disable UART0 interrupt.
1: Enable UART0 interrupt.
3
ET1
Enable Timer 1 Interrupt.
This bit sets the masking of the Timer 1 interrupt.
0: Disable all Timer 1 interrupt.
1: Enable interrupt requests generated by the TF1 flag.
2
EX1
Enable External Interrupt 1.
This bit sets the masking of External Interrupt 1.
0: Disable external interrupt 1.
1: Enable interrupt requests generated by the INT1 input.
1
ET0
Enable Timer 0 Interrupt.
This bit sets the masking of the Timer 0 interrupt.
0: Disable all Timer 0 interrupt.
1: Enable interrupt requests generated by the TF0 flag.
0
EX0
Enable External Interrupt 0.
This bit sets the masking of External Interrupt 0.
0: Disable external interrupt 0.
1: Enable interrupt requests generated by the INT0 input.
Enable All Interrupts.
Globally enables/disables all interrupts. It overrides individual interrupt mask settings.
0: Disable all interrupt sources.
1: Enable each interrupt according to its individual mask setting.
Enable Serial Peripheral Interface (SPI0) Interrupt.
This bit sets the masking of the SPI0 interrupts.
0: Disable all SPI0 interrupts.
1: Enable interrupt requests generated by SPI0.
Rev. 1.2
116
C8051F55x/56x/57x
SFR Definition 13.2. IP: Interrupt Priority
Bit
7
Name
6
5
4
3
2
1
0
PSPI0
PT2
PS0
PT1
PX1
PT0
PX0
Type
R
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
1
0
0
0
0
0
0
0
SFR Address = 0xB8; Bit-Addressable; SFR Page = All Pages
Bit
Name
Function
7
Unused
6
PSPI0
5
PT2
Timer 2 Interrupt Priority Control.
This bit sets the priority of the Timer 2 interrupt.
0: Timer 2 interrupt set to low priority level.
1: Timer 2 interrupt set to high priority level.
4
PS0
UART0 Interrupt Priority Control.
This bit sets the priority of the UART0 interrupt.
0: UART0 interrupt set to low priority level.
1: UART0 interrupt set to high priority level.
3
PT1
Timer 1 Interrupt Priority Control.
This bit sets the priority of the Timer 1 interrupt.
0: Timer 1 interrupt set to low priority level.
1: Timer 1 interrupt set to high priority level.
2
PX1
External Interrupt 1 Priority Control.
This bit sets the priority of the External Interrupt 1 interrupt.
0: External Interrupt 1 set to low priority level.
1: External Interrupt 1 set to high priority level.
1
PT0
Timer 0 Interrupt Priority Control.
This bit sets the priority of the Timer 0 interrupt.
0: Timer 0 interrupt set to low priority level.
1: Timer 0 interrupt set to high priority level.
0
PX0
External Interrupt 0 Priority Control.
This bit sets the priority of the External Interrupt 0 interrupt.
0: External Interrupt 0 set to low priority level.
1: External Interrupt 0 set to high priority level.
117
Read = 1b, Write = Don't Care.
Serial Peripheral Interface (SPI0) Interrupt Priority Control.
This bit sets the priority of the SPI0 interrupt.
0: SPI0 interrupt set to low priority level.
1: SPI0 interrupt set to high priority level.
Rev. 1.2
C8051F55x/56x/57x
SFR Definition 13.3. EIE1: Extended Interrupt Enable 1
Bit
7
6
5
4
3
2
1
0
Name
ELIN0
ET3
ECP1
ECP0
EPCA0
EADC0
EWADC0
ESMB0
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Address = 0xE6; SFR Page = All Pages
Bit
Name
Function
7
ELIN0
6
ET3
5
ECP1
Enable Comparator1 (CP1) Interrupt.
This bit sets the masking of the CP1 interrupt.
0: Disable CP1 interrupts.
1: Enable interrupt requests generated by the CP1RIF or CP1FIF flags.
4
ECP0
Enable Comparator0 (CP0) Interrupt.
This bit sets the masking of the CP0 interrupt.
0: Disable CP0 interrupts.
1: Enable interrupt requests generated by the CP0RIF or CP0FIF flags.
3
EPCA0
Enable Programmable Counter Array (PCA0) Interrupt.
This bit sets the masking of the PCA0 interrupts.
0: Disable all PCA0 interrupts.
1: Enable interrupt requests generated by PCA0.
2
EADC0
Enable ADC0 Conversion Complete Interrupt.
This bit sets the masking of the ADC0 Conversion Complete interrupt.
0: Disable ADC0 Conversion Complete interrupt.
1: Enable interrupt requests generated by the AD0INT flag.
1
0
Enable LIN0 Interrupt.
This bit sets the masking of the LIN0 interrupt.
0: Disable LIN0 interrupts.
1: Enable interrupt requests generated by the LIN0INT flag.
Enable Timer 3 Interrupt.
This bit sets the masking of the Timer 3 interrupt.
0: Disable Timer 3 interrupts.
1: Enable interrupt requests generated by the TF3L or TF3H flags.
EWADC0 Enable Window Comparison ADC0 Interrupt.
This bit sets the masking of ADC0 Window Comparison interrupt.
0: Disable ADC0 Window Comparison interrupt.
1: Enable interrupt requests generated by ADC0 Window Compare flag (AD0WINT).
ESMB0
Enable SMBus (SMB0) Interrupt.
This bit sets the masking of the SMB0 interrupt.
0: Disable all SMB0 interrupts.
1: Enable interrupt requests generated by SMB0.
Rev. 1.2
118
C8051F55x/56x/57x
SFR Definition 13.4. EIP1: Extended Interrupt Priority 1
Bit
7
6
5
4
3
2
1
0
Name
PLIN0
PT3
PCP1
PCP0
PPCA0
PADC0
PWADC0
PSMB0
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Address = 0xF6; SFR Page = 0x00 and 0x0F
Bit
Name
Function
7
PLIN0
6
PT3
Timer 3 Interrupt Priority Control.
This bit sets the priority of the Timer 3 interrupt.
0: Timer 3 interrupts set to low priority level.
1: Timer 3 interrupts set to high priority level.
5
PCP1
Comparator0 (CP1) Interrupt Priority Control.
This bit sets the priority of the CP1 interrupt.
0: CP1 interrupt set to low priority level.
1: CP1 interrupt set to high priority level.
4
PCP0
Comparator0 (CP0) Interrupt Priority Control.
This bit sets the priority of the CP0 interrupt.
0: CP0 interrupt set to low priority level.
1: CP0 interrupt set to high priority level.
3
PPCA0
Programmable Counter Array (PCA0) Interrupt Priority Control.
This bit sets the priority of the PCA0 interrupt.
0: PCA0 interrupt set to low priority level.
1: PCA0 interrupt set to high priority level.
2
PADC0
ADC0 Conversion Complete Interrupt Priority Control.
This bit sets the priority of the ADC0 Conversion Complete interrupt.
0: ADC0 Conversion Complete interrupt set to low priority level.
1: ADC0 Conversion Complete interrupt set to high priority level.
1
0
119
LIN0 Interrupt Priority Control.
This bit sets the priority of the LIN0 interrupt.
0: LIN0 interrupts set to low priority level.
1: LIN0 interrupts set to high priority level.
PWADC0 ADC0 Window Comparator Interrupt Priority Control.
This bit sets the priority of the ADC0 Window interrupt.
0: ADC0 Window interrupt set to low priority level.
1: ADC0 Window interrupt set to high priority level.
PSMB0
SMBus (SMB0) Interrupt Priority Control.
This bit sets the priority of the SMB0 interrupt.
0: SMB0 interrupt set to low priority level.
1: SMB0 interrupt set to high priority level.
Rev. 1.2
C8051F55x/56x/57x
SFR Definition 13.5. EIE2: Extended Interrupt Enable 2
Bit
7
6
5
4
3
Name
2
1
0
EMAT
ECAN0
EREG0
Type
R
R
R
R
R
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Address = 0xE7; SFR Page = All Pages
Bit
Name
Function
7:3
Unused
Read = 00000b; Write = Don’t Care.
2
EMAT
1
ECAN0
Enable CAN0 Interrupts.
This bit sets the masking of the CAN0 interrupt.
0: Disable all CAN0 interrupts.
1: Enable interrupt requests generated by CAN0.
0
EREG0
Enable Voltage Regulator Dropout Interrupt.
This bit sets the masking of the Voltage Regulator Dropout interrupt.
0: Disable the Voltage Regulator Dropout interrupt.
1: Enable the Voltage Regulator Dropout interrupt.
Enable Port Match Interrupt.
This bit sets the masking of the Port Match interrupt.
0: Disable all Port Match interrupts.
1: Enable interrupt requests generated by a Port Match
Rev. 1.2
120
C8051F55x/56x/57x
SFR Definition 13.6. EIP2: Extended Interrupt Priority Enabled 2
Bit
7
6
5
4
3
Name
2
1
0
PMAT
PCAN0
PREG0
Type
R
R
R
R
R
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Address = 0xF7; SFR Page = 0x00 and 0x0F
Bit
Name
Function
7:3
Unused
2
PMAT
1
PCAN0
CAN0 Interrupt Priority Control.
This bit sets the priority of the CAN0 interrupt.
0: CAN0 interrupt set to low priority level.
1: CAN0 interrupt set to high priority level.
0
PREG0
Voltage Regulator Dropout Interrupt Priority Control.
This bit sets the priority of the Voltage Regulator Dropout interrupt.
0: Voltage Regulator Dropout interrupt set to low priority level.
1: Voltage Regulator Dropout interrupt set to high priority level.
121
Read = 00000b; Write = Don’t Care.
Port Match Interrupt Priority Control.
This bit sets the priority of the Port Match interrupt.
0: Port Match interrupt set to low priority level.
1: Port Match interrupt set to high priority level.
Rev. 1.2
C8051F55x/56x/57x
13.3. External Interrupts INT0 and INT1
The INT0 and INT1 external interrupt sources are configurable as active high or low, edge or level sensitive. The IN0PL (INT0 Polarity) and IN1PL (INT1 Polarity) bits in the IT01CF register select active high or
active low; the IT0 and IT1 bits in TCON (Section “25.1. Timer 0 and Timer 1” on page 261) select level or
edge sensitive. The table below lists the possible configurations.
IT0
IN0PL
INT0 Interrupt
IT1
IN1PL
INT1 Interrupt
1
0
Active low, edge sensitive
1
0
Active low, edge sensitive
1
1
Active high, edge sensitive
1
1
Active high, edge sensitive
0
0
Active low, level sensitive
0
0
Active low, level sensitive
0
1
Active high, level sensitive
0
1
Active high, level sensitive
INT0 and INT1 are assigned to Port pins as defined in the IT01CF register (see SFR Definition 13.7). Note
that INT0 and INT0 Port pin assignments are independent of any Crossbar assignments. INT0 and INT1
will monitor their assigned Port pins without disturbing the peripheral that was assigned the Port pin via the
Crossbar. To assign a Port pin only to INT0 and/or INT1, configure the Crossbar to skip the selected pin(s).
This is accomplished by setting the associated bit in register XBR0 (see Section “19.3. Priority Crossbar
Decoder” on page 172 for complete details on configuring the Crossbar).
IE0 (TCON.1) and IE1 (TCON.3) serve as the interrupt-pending flags for the INT0 and INT1 external interrupts, respectively. If an INT0 or INT1 external interrupt is configured as edge-sensitive, the corresponding
interrupt-pending flag is automatically cleared by the hardware when the CPU vectors to the ISR. When
configured as level sensitive, the interrupt-pending flag remains logic 1 while the input is active as defined
by the corresponding polarity bit (IN0PL or IN1PL); the flag remains logic 0 while the input is inactive. The
external interrupt source must hold the input active until the interrupt request is recognized. It must then
deactivate the interrupt request before execution of the ISR completes or another interrupt request will be
generated.
Rev. 1.2
122
C8051F55x/56x/57x
SFR Definition 13.7. IT01CF: INT0/INT1 Configuration
Bit
7
6
Name
IN1PL
IN1SL[2:0]
IN0PL
IN0SL[2:0]
Type
R/W
R/W
R/W
R/W
Reset
0
0
5
0
4
0
SFR Address = 0xE4; SFR Page = 0x0F
Bit
Name
7
6:4
3
2:0
123
IN1PL
3
0
2
0
1
0
0
0
Function
INT1 Polarity.
0: INT1 input is active low.
1: INT1 input is active high.
IN1SL[2:0] INT1 Port Pin Selection Bits.
These bits select which Port pin is assigned to INT1. Note that this pin assignment is
independent of the Crossbar; INT1 will monitor the assigned Port pin without disturbing the peripheral that has been assigned the Port pin via the Crossbar. The Crossbar
will not assign the Port pin to a peripheral if it is configured to skip the selected pin.
000: Select P1.0
001: Select P1.1
010: Select P1.2
011: Select P1.3
100: Select P1.4
101: Select P1.5
110: Select P1.6
111: Select P1.7
IN0PL
INT0 Polarity.
0: INT0 input is active low.
1: INT0 input is active high.
IN0SL[2:0] INT0 Port Pin Selection Bits.
These bits select which Port pin is assigned to INT0. Note that this pin assignment is
independent of the Crossbar; INT0 will monitor the assigned Port pin without disturbing the peripheral that has been assigned the Port pin via the Crossbar. The Crossbar
will not assign the Port pin to a peripheral if it is configured to skip the selected pin.
000: Select P1.0
001: Select P1.1
010: Select P1.2
011: Select P1.3
100: Select P1.4
101: Select P1.5
110: Select P1.6
111: Select P1.7
Rev. 1.2
C8051F55x/56x/57x
14. Flash Memory
On-chip, re-programmable Flash memory is included for program code and non-volatile data storage. The
Flash memory can be programmed in-system, a single byte at a time, through the C2 interface or by software using the MOVX instruction. Once cleared to logic 0, a Flash bit must be erased to set it back to
logic 1. Flash bytes would typically be erased (set to 0xFF) before being reprogrammed. The write and
erase operations are automatically timed by hardware for proper execution; data polling to determine the
end of the write/erase operation is not required. Code execution is stalled during a Flash write/erase operation. Refer to Table 5.5 for complete Flash memory electrical characteristics.
14.1. Programming The Flash Memory
The simplest means of programming the Flash memory is through the C2 interface using programming
tools provided by Silicon Labs or a third party vendor. This is the only means for programming a non-initialized device. For details on the C2 commands to program Flash memory, see Section “27. C2 Interface” on
page 300.
To ensure the integrity of Flash contents, it is strongly recommended that the on-chip VDD Monitor be
enabled in any system that includes code that writes and/or erases Flash memory from software. See Section 14.4 for more details. Before performing any Flash write or erase procedure, set the FLEWT bit in
Flash Scale register (FLSCL) to 1. Also, note that 8-bit MOVX instructions cannot be used to erase or write
to Flash memory at addresses higher than 0x00FF.
For –I (Industrial Grade) parts, parts programmed at a cold temperature below 0 °C may exhibit weakly
programmed flash memory bits. If programmed at 0 °C or higher, there is no problem reading Flash across
the entire temperature range of -40 °C to 125 °C. This temperature restriction does not apply to –A (Automotive Grade) devices.
14.1.1. Flash Lock and Key Functions
Flash writes and erases by user software are protected with a lock and key function. The Flash Lock and
Key Register (FLKEY) must be written with the correct key codes, in sequence, before Flash operations
may be performed. The key codes are: 0xA5, 0xF1. The timing does not matter, but the codes must be
written in order. If the key codes are written out of order, or the wrong codes are written, Flash writes and
erases will be disabled until the next system reset. Flash writes and erases will also be disabled if a Flash
write or erase is attempted before the key codes have been written properly. The Flash lock resets after
each write or erase; the key codes must be written again before a following Flash operation can be performed. The FLKEY register is detailed in SFR Definition 14.2.
Rev. 1.2
124
C8051F55x/56x/57x
14.1.2. Flash Erase Procedure
The Flash memory can be programmed by software using the MOVX write instruction with the address and
data byte to be programmed provided as normal operands. Before writing to Flash memory using MOVX,
Flash write operations must be enabled by doing the following: (1) setting the PSWE Program Store Write
Enable bit (PSCTL.0) to logic 1 (this directs the MOVX writes to target Flash memory); and (2) Writing the
Flash key codes in sequence to the Flash Lock register (FLKEY). The PSWE bit remains set until cleared
by software.
A write to Flash memory can clear bits to logic 0 but cannot set them; only an erase operation can set bits
to logic 1 in Flash. A byte location to be programmed should be erased before a new value is written.
The Flash memory is organized in 512-byte pages. The erase operation applies to an entire page (setting
all bytes in the page to 0xFF). To erase an entire 512-byte page, perform the following steps:
1. Disable interrupts (recommended).
2. Set the FLEWT bit (register FLSCL).
3. Set the PSEE bit (register PSCTL).
4. Set the PSWE bit (register PSCTL).
5. Write the first key code to FLKEY: 0xA5.
6. Write the second key code to FLKEY: 0xF1.
7. Using the MOVX instruction, write a data byte to any location within the 512-byte page to be erased.
8. Clear the PSWE and PSEE bits.
14.1.3. Flash Write Procedure
Flash bytes are programmed by software with the following sequence:
1. Disable interrupts (recommended).
2. Erase the 512-byte Flash page containing the target location, as described in Section 14.1.2.
3. Set the FLEWT bit (register FLSCL).
4. Set the PSWE bit (register PSCTL).
5. Clear the PSEE bit (register PSCTL).
6. Write the first key code to FLKEY: 0xA5.
7. Write the second key code to FLKEY: 0xF1.
8. Using the MOVX instruction, write a single data byte to the desired location within the 512-byte sector.
9. Clear the PSWE bit.
Steps 5–7 must be repeated for each byte to be written. After Flash writes are complete, PSWE should be
cleared so that MOVX instructions do not target program memory.
125
Rev. 1.2
C8051F55x/56x/57x
14.1.4. Flash Write Optimization
The Flash write procedure includes a block write option to optimize the time to perform consecutive byte
writes. When block write is enabled by setting the CHBLKW bit (CCH0CN.0), writes to two consecutive
bytes in Flash require the same amount of time as a single byte write. This is performed by caching the first
byte that is written to Flash and then committing both bytes to Flash when the second byte is written. When
block writes are enabled, if the second write does not occur, the first data byte written is not actually written
to Flash. Flash bytes with block write enabled are programmed by software with the following sequence:
1. Disable interrupts (recommended).
2. Erase the 512-byte Flash page containing the target location, as described in Section 14.1.2.
3. Set the FLEWT bit (register FLSCL).
4. Set the CHBLKW bit (register CCH0CN).
5. Set the PSWE bit (register PSCTL).
6. Clear the PSEE bit (register PSCTL).
7. Write the first key code to FLKEY: 0xA5.
8. Write the second key code to FLKEY: 0xF1.
9. Using the MOVX instruction, write the first data byte to the desired location within the 512-byte sector.
10.Write the first key code to FLKEY: 0xA5.
11. Write the second key code to FLKEY: 0xF1.
12.Using the MOVX instruction, write the second data byte to the desired location within the 512-byte
sector. The location of the second byte must be the next higher address from the first data byte.
13.Clear the PSWE bit.
14.Clear the CHBLKW bit.
Rev. 1.2
126
C8051F55x/56x/57x
14.2. Non-volatile Data Storage
The Flash memory can be used for non-volatile data storage as well as program code. This allows data
such as calibration coefficients to be calculated and stored at run time. Data is written using the MOVX
write instruction and read using the MOVC instruction. Note: MOVX read instructions always target XRAM.
14.3. Security Options
The CIP-51 provides security options to protect the Flash memory from inadvertent modification by software as well as to prevent the viewing of proprietary program code and constants. The Program Store
Write Enable (bit PSWE in register PSCTL) and the Program Store Erase Enable (bit PSEE in register
PSCTL) bits protect the Flash memory from accidental modification by software. PSWE must be explicitly
set to 1 before software can modify the Flash memory; both PSWE and PSEE must be set to 1 before software can erase Flash memory. Additional security features prevent proprietary program code and data
constants from being read or altered across the C2 interface.
A Security Lock Byte located at the last byte of Flash user space offers protection of the Flash program
memory from access (reads, writes, or erases) by unprotected code or the C2 interface. The Flash security
mechanism allows the user to lock n 512-byte Flash pages, starting at page 0 (addresses 0x0000 to
0x01FF), where n is the ones complement number represented by the Security Lock Byte. Note that the
page containing the Flash Security Lock Byte is unlocked when no other Flash pages are locked
(all bits of the Lock Byte are 1) and locked when any other Flash pages are locked (any bit of the
Lock Byte is 0). See example in Figure 14.1.
Reserved Area
Locked when
any other FLASH
pages are locked
Lock Byte
Lock Byte Page
Unlocked FLASH Pages
Access limit set
according to the
FLASH security
lock byte
Locked Flash Pages
Security Lock Byte:
1s Complement:
Flash pages locked:
11111101b
00000010b
3 (First two Flash pages + Lock Byte Page)
Figure 14.1. Flash Program Memory Map
127
Rev. 1.2
C8051F55x/56x/57x
The level of Flash security depends on the Flash access method. The three Flash access methods that
can be restricted are reads, writes, and erases from the C2 debug interface, user firmware executing on
unlocked pages, and user firmware executing on locked pages. Table 14.1 summarizes the Flash security
features of the C8051F55x/56x/57x devices.
Table 14.1. Flash Security Summary
Action
C2 Debug
Interface
User Firmware executing from:
an unlocked page
a locked page
Permitted
Permitted
Permitted
Not Permitted
Flash Error Reset
Permitted
Read or Write page containing Lock Byte
(if no pages are locked)
Permitted
Permitted
Permitted
Read or Write page containing Lock Byte
(if any page is locked)
Not Permitted
Flash Error Reset
Permitted
Read contents of Lock Byte
(if no pages are locked)
Permitted
Permitted
Permitted
Read contents of Lock Byte
(if any page is locked)
Not Permitted
Flash Error Reset
Permitted
Read, Write or Erase unlocked pages
(except page with Lock Byte)
Read, Write or Erase locked pages
(except page with Lock Byte)
Permitted
Flash Error Reset Flash Error Reset
C2 Device
Erase Only
Flash Error Reset Flash Error Reset
Lock additional pages
(change '1's to '0's in the Lock Byte)
Not Permitted
Flash Error Reset Flash Error Reset
Unlock individual pages
(change '0's to '1's in the Lock Byte)
Not Permitted
Flash Error Reset Flash Error Reset
Read, Write or Erase Reserved Area
Not Permitted
Flash Error Reset Flash Error Reset
Erase page containing Lock Byte
(if no pages are locked)
Erase page containing Lock Byte—Unlock all
pages (if any page is locked)
C2 Device Erase—Erases all Flash pages including the page containing the Lock Byte.
Flash Error Reset—Not permitted; Causes Flash Error Device Reset (FERROR bit in RSTSRC is '1' after
reset).
- All prohibited operations that are performed via the C2 interface are ignored (do not cause device reset).
- Locking any Flash page also locks the page containing the Lock Byte.
- Once written to, the Lock Byte cannot be modified except by performing a C2 Device Erase.
- If user code writes to the Lock Byte, the Lock does not take effect until the next device reset.
Rev. 1.2
128
C8051F55x/56x/57x
14.4. Flash Write and Erase Guidelines
Any system which contains routines which write or erase Flash memory from software involves some risk
that the write or erase routines will execute unintentionally if the CPU is operating outside its specified
operating range of VDD, system clock frequency, or temperature. This accidental execution of Flash modifying code can result in alteration of Flash memory contents causing a system failure that is only recoverable by re-Flashing the code in the device.
The following guidelines are recommended for any system which contains routines which write or erase
Flash from code.
14.4.1. VDD Maintenance and the VDD monitor
1. If the system power supply is subject to voltage or current "spikes," add sufficient transient protection
devices to the power supply to ensure that the supply voltages listed in the Absolute Maximum Ratings
table are not exceeded.
2. Make certain that the minimum VREGIN rise time specification of 1 ms is met. If the system cannot
meet this rise time specification, then add an external VDD brownout circuit to the RST pin of the device
that holds the device in reset until VDD reaches the minimum threshold and re-asserts RST if VDD drops
below the minimum threshold.
3. Enable the on-chip VDD monitor in the high setting and enable the VDD monitor as a reset source as
early in code as possible. This should be the first set of instructions executed after the Reset Vector.
For C-based systems, this will involve modifying the startup code added by the C compiler. See your
compiler documentation for more details. Make certain that there are no delays in software between
enabling the VDD monitor in the high setting and enabling the VDD monitor as a reset source. Code
examples showing this can be found in “AN201: Writing to Flash from Firmware", available from the
Silicon Laboratories web site.
4. As an added precaution, explicitly enable the VDD monitor in the high setting and enable the VDD
monitor as a reset source inside the functions that write and erase Flash memory. The VDD monitor
enable instructions should be placed just after the instruction to set PSWE to a 1, but before the Flash
write or erase operation instruction.
Note: The output of the internal voltage regulator is calibrated by the MCU immediately after any reset
event. The output of the un-calibrated internal regulator could be below the high threshold setting of
the VDD Monitor. If this is the case and the VDD Monitor is set to the high threshold setting and if the
MCU receives a non-power on reset (POR), the MCU will remain in reset until a POR occurs (i.e.,
VDD Monitor will keep the device in reset). A POR will force the VDD Monitor to the low threshold
setting which is guaranteed to be below the un-calibrated output of the internal regulator. The device
will then exit reset and resume normal operation. It is for this reason Silicon Labs strongly
recommends that the VDD Monitor is always left in the low threshold setting (i.e. default value upon
POR). When programming the Flash in-system, the VDD Monitor must be set to the high threshold
setting. For the highest system reliability, the time the VDD Monitor is set to the high threshold setting
should be minimized (e.g., setting the VDD Monitor to the high threshold setting just before the Flash
write operation and then changing it back to the low threshold setting immediately after the Flash
write operation).
5. Make certain that all writes to the RSTSRC (Reset Sources) register use direct assignment operators
and explicitly DO NOT use the bit-wise operators (such as AND or OR). For example, "RSTSRC =
0x02" is correct. "RSTSRC |= 0x02" is incorrect.
6. Make certain that all writes to the RSTSRC register explicitly set the PORSF bit to a 1. Areas to check
are initialization code which enables other reset sources, such as the Missing Clock Detector or
Comparator, for example, and instructions which force a Software Reset. A global search on "RSTSRC"
can quickly verify this.
129
Rev. 1.2
C8051F55x/56x/57x
14.4.2. PSWE Maintenance
1. Reduce the number of places in code where the PSWE bit (b0 in PSCTL) is set to a 1. There should be
exactly one routine in code that sets PSWE to a 1 to write Flash bytes and one routine in code that sets
PSWE and PSEE both to a 1 to erase Flash pages.
2. Minimize the number of variable accesses while PSWE is set to a 1. Handle pointer address updates
and loop variable maintenance outside the "PSWE = 1;... PSWE = 0;" area. Code examples showing
this can be found in ”AN201: Writing to Flash from Firmware" available from the Silicon Laboratories
web site.
3. Disable interrupts prior to setting PSWE to a 1 and leave them disabled until after PSWE has been
reset to '0'. Any interrupts posted during the Flash write or erase operation will be serviced in priority
order after the Flash operation has been completed and interrupts have been re-enabled by software.
4. Make certain that the Flash write and erase pointer variables are not located in XRAM. See your
compiler documentation for instructions regarding how to explicitly locate variables in different memory
areas.
5. Add address bounds checking to the routines that write or erase Flash memory to ensure that a routine
called with an illegal address does not result in modification of the Flash.
14.4.3. System Clock
1. If operating from an external crystal, be advised that crystal performance is susceptible to electrical
interference and is sensitive to layout and to changes in temperature. If the system is operating in an
electrically noisy environment, use the internal oscillator or use an external CMOS clock.
2. If operating from the external oscillator, switch to the internal oscillator during Flash write or erase
operations. The external oscillator can continue to run, and the CPU can switch back to the external
oscillator after the Flash operation has completed.
Additional Flash recommendations and example code can be found in “AN201: Writing to Flash from Firmware" available from the Silicon Laboratories web site.
Rev. 1.2
130
C8051F55x/56x/57x
SFR Definition 14.1. PSCTL: Program Store R/W Control
Bit
7
6
5
4
3
2
Name
1
0
PSEE
PSWE
Type
R
R
R
R
R
R
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Address = 0x8F; SFR Page = 0x00
Bit
Name
7:2
Unused
1
PSEE
Function
Read = 000000b, Write = don’t care.
Program Store Erase Enable.
Setting this bit (in combination with PSWE) allows an entire page of Flash program
memory to be erased. If this bit is logic 1 and Flash writes are enabled (PSWE is logic
1), a write to Flash memory using the MOVX instruction will erase the entire page that
contains the location addressed by the MOVX instruction. The value of the data byte
written does not matter.
0: Flash program memory erasure disabled.
1: Flash program memory erasure enabled.
0
PSWE
Program Store Write Enable.
Setting this bit allows writing a byte of data to the Flash program memory using the
MOVX write instruction. The Flash location should be erased before writing data.
0: Writes to Flash program memory disabled.
1: Writes to Flash program memory enabled; the MOVX write instruction targets Flash
memory.
131
Rev. 1.2
C8051F55x/56x/57x
SFR Definition 14.2. FLKEY: Flash Lock and Key
Bit
7
6
5
4
3
Name
FLKEY[7:0]
Type
R/W
Reset
0
0
0
0
SFR Address = 0xB7; SFR Page = All Pages
Bit
Name
7:0
0
2
1
0
0
0
0
Function
FLKEY[7:0] Flash Lock and Key Register.
Write:
This register provides a lock and key function for Flash erasures and writes. Flash
writes and erases are enabled by writing 0xA5 followed by 0xF1 to the FLKEY register. Flash writes and erases are automatically disabled after the next write or erase is
complete. If any writes to FLKEY are performed incorrectly, or if a Flash write or erase
operation is attempted while these operations are disabled, the Flash will be permanently locked from writes or erasures until the next device reset. If an application
never writes to Flash, it can intentionally lock the Flash by writing a non-0xA5 value to
FLKEY from software.
Read:
When read, bits 1–0 indicate the current Flash lock state.
00: Flash is write/erase locked.
01: The first key code has been written (0xA5).
10: Flash is unlocked (writes/erases allowed).
11: Flash writes/erases disabled until the next reset.
Rev. 1.2
132
C8051F55x/56x/57x
SFR Definition 14.3. FLSCL: Flash Scale
Bit
7
6
5
4
3
2
1
0
Name
Reserved
Reserved
Reserved
FLRT
Reserved
Reserved
FLEWT
Reserved
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Address = 0xB6; SFR Page = All Pages
Bit
Name
7:5
Reserved
4
FLRT
Function
Must Write 000b.
Flash Read Time Control.
This bit should be programmed to the smallest allowed value, according to the system
clock speed.
0: SYSCLK < 25 MHz (Flash read strobe is one system clock).
1: SYSCLK > 25 MHz (Flash read strobe is two system clocks).
3:2
Reserved
1
FLEWT
Must Write 00b.
Flash Erase Write Time Control.
This bit should be set to 1b before Writing or Erasing Flash.
0: Short Flash Erase / Write Timing.
1: Extended Flash Erase / Write Timing.
0
133
Reserved
Must Write 0b.
Rev. 1.2
C8051F55x/56x/57x
SFR Definition 14.4. CCH0CN: Cache Control
Bit
7
6
5
4
3
2
1
0
Name
Reserved
Reserved
CHPFEN
Reserved
Reserved
Reserved
Reserved
CHBLKW
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
1
0
0
0
0
0
1
0
SFR Address = 0xE3; SFR Page = 0x0F
Bit
Name
Function
7:6
Reserved
Must Write 00b
5
CHPFEN
Cache Prefect Enable Bit.
0: Prefetch engine is disabled.
1: Prefetch engine is enabled.
4:1
Reserved
Must Write 0000b.
0
CHBLKW
Block Write Enable Bit.
This bit allows block writes to Flash memory from firmware.
0: Each byte of a software Flash write is written individually.
1: Flash bytes are written in groups of two.
SFR Definition 14.5. ONESHOT: Flash Oneshot Period
Bit
7
6
5
4
3
2
PERIOD[3:0]
Name
Type
R
R
R
R
R/W
R/W
R/W
R/W
Reset
0
0
0
0
1
1
1
1
SFR Address = 0xBE; SFR Page = 0x0F
Bit
Name
7:4
3:0
Unused
Function
Read = 0000b. Write = don’t care.
PERIOD[3:0] Oneshot Period Control Bits.
These bits limit the internal Flash read strobe width as follows. When the Flash read
strobe is de-asserted, the Flash memory enters a low-power state for the remainder
of the system clock cycle.
FLASH RDMAX = 5ns + ( PERIOD × 5ns )
Rev. 1.2
134
C8051F55x/56x/57x
15. Power Management Modes
The C8051F55x/56x/57x devices have three software programmable power management modes: Idle,
Stop, and Suspend. Idle mode and Stop mode are part of the standard 8051 architecture, while Suspend
mode is an enhanced power-saving mode implemented by the high-speed oscillator peripheral.
Idle mode halts the CPU while leaving the peripherals and clocks active. In Stop mode, the CPU is halted,
all interrupts and timers (except the Missing Clock Detector) are inactive, and the internal oscillator is
stopped (analog peripherals remain in their selected states; the external oscillator is not affected). Suspend mode is similar to Stop mode in that the internal oscillator and CPU are halted, but the device can
wake on events such as a Port Match or Comparator low output. Since clocks are running in Idle mode,
power consumption is dependent upon the system clock frequency and the number of peripherals left in
active mode before entering Idle. Stop mode and Suspend mode consume the least power because the
majority of the device is shut down with no clocks active. SFR Definition 15.1 describes the Power Control
Register (PCON) used to control the C8051F55x/56x/57x devices’ Stop and Idle power management
modes. Suspend mode is controlled by the SUSPEND bit in the OSCICN register (SFR Definition 18.2).
Although the C8051F55x/56x/57x has Idle, Stop, and Suspend modes available, more control over the
device power can be achieved by enabling/disabling individual peripherals as needed. Each analog
peripheral can be disabled when not in use and placed in low power mode. Digital peripherals, such as timers or serial buses, draw little power when they are not in use. Turning off oscillators lowers power consumption considerably, at the expense of reduced functionality.
15.1. Idle Mode
Setting the Idle Mode Select bit (PCON.0) causes the hardware to halt the CPU and enter Idle mode as
soon as the instruction that sets the bit completes execution. All internal registers and memory maintain
their original data. All analog and digital peripherals can remain active during Idle mode.
Idle mode is terminated when an enabled interrupt is asserted or a reset occurs. The assertion of an
enabled interrupt will cause the Idle Mode Selection bit (PCON.0) to be cleared and the CPU to resume
operation. The pending interrupt will be serviced and the next instruction to be executed after the return
from interrupt (RETI) will be the instruction immediately following the one that set the Idle Mode Select bit.
If Idle mode is terminated by an internal or external reset, the CIP-51 performs a normal reset sequence
and begins program execution at address 0x0000.
Note: If the instruction following the write of the IDLE bit is a single-byte instruction and an interrupt occurs
during the execution phase of the instruction that sets the IDLE bit, the CPU may not wake from Idle mode
when a future interrupt occurs. Therefore, instructions that set the IDLE bit should be followed by an
instruction that has two or more opcode bytes, for example:
// in ‘C’:
PCON |= 0x01;
PCON = PCON;
// set IDLE bit
// ... followed by a 3-cycle dummy instruction
; in assembly:
ORL PCON, #01h
MOV PCON, PCON
; set IDLE bit
; ... followed by a 3-cycle dummy instruction
If enabled, the Watchdog Timer (WDT) will eventually cause an internal watchdog reset and thereby terminate the Idle mode. This feature protects the system from an unintended permanent shutdown in the event
of an inadvertent write to the PCON register. If this behavior is not desired, the WDT may be disabled by
software prior to entering the Idle mode if the WDT was initially configured to allow this operation. This provides the opportunity for additional power savings, allowing the system to remain in the Idle mode indefinitely, waiting for an external stimulus to wake up the system. Refer to Section “16.6. PCA Watchdog Timer
Reset” on page 142 for more information on the use and configuration of the WDT.
Rev. 1.2
135
C8051F55x/56x/57x
15.2. Stop Mode
Setting the Stop Mode Select bit (PCON.1) causes the controller core to enter Stop mode as soon as the
instruction that sets the bit completes execution. In Stop mode the internal oscillator, CPU, and all digital
peripherals are stopped; the state of the external oscillator circuit is not affected. Each analog peripheral
(including the external oscillator circuit) may be shut down individually prior to entering Stop Mode. Stop
mode can only be terminated by an internal or external reset. On reset, the device performs the normal
reset sequence and begins program execution at address 0x0000.
If enabled, the Missing Clock Detector will cause an internal reset and thereby terminate the Stop mode.
The Missing Clock Detector should be disabled if the CPU is to be put to in STOP mode for longer than the
MCD timeout of 100 µs.
15.3. Suspend Mode
Setting the SUSPEND bit (OSCICN.5) causes the hardware to halt the CPU and the high-frequency internal oscillator, and go into Suspend mode as soon as the instruction that sets the bit completes execution.
All internal registers and memory maintain their original data. Most digital peripherals are not active in Suspend mode. The exception to this is the Port Match feature.
Suspend mode can be terminated by three types of events, a port match (described in Section “19.5. Port
Match” on page 179), a Comparator low output (if enabled), or a device reset event. When Suspend mode
is terminated, the device will continue execution on the instruction following the one that set the SUSPEND
bit. If the wake event was configured to generate an interrupt, the interrupt will be serviced upon waking
the device. If Suspend mode is terminated by an internal or external reset, the CIP-51 performs a normal
reset sequence and begins program execution at address 0x0000.
Note: Before entering suspend mode, firmware must set the ZTCEN bit in REF0CN (SFR Definition 7.1).
136
Rev. 1.2
C8051F55x/56x/57x
SFR Definition 15.1. PCON: Power Control
Bit
7
6
5
4
3
2
1
0
Name
GF[5:0]
STOP
IDLE
Type
R/W
R/W
R/W
0
0
Reset
0
0
0
SFR Address = 0x87; SFR Page = All Pages
Bit
Name
7:2
GF[5:0]
0
0
0
Function
General Purpose Flags 5–0.
These are general purpose flags for use under software control.
1
STOP
Stop Mode Select.
Setting this bit will place the CIP-51 in Stop mode. This bit will always be read as 0.
1: CPU goes into Stop mode (internal oscillator stopped).
0
IDLE
IDLE: Idle Mode Select.
Setting this bit will place the CIP-51 in Idle mode. This bit will always be read as 0.
1: CPU goes into Idle mode. (Shuts off clock to CPU, but clock to Timers, Interrupts,
Serial Ports, and Analog Peripherals are still active.)
Rev. 1.2
137
C8051F55x/56x/57x
16. Reset Sources
Reset circuitry allows the controller to be easily placed in a predefined default condition. On entry to this
reset state, the following occur:
CIP-51 halts program execution
Special Function Registers (SFRs) are initialized to their defined reset values
External Port pins are forced to a known state
Interrupts and timers are disabled.
All SFRs are reset to the predefined values noted in the SFR detailed descriptions. The contents of internal
data memory are unaffected during a reset; any previously stored data is preserved. However, since the
stack pointer SFR is reset, the stack is effectively lost, even though the data on the stack is not altered.
The Port I/O latches are reset to 0xFF (all logic ones) in open-drain mode. Weak pullups are enabled
during and after the reset. For VDD Monitor and power-on resets, the RST pin is driven low until the device
exits the reset state.
Note: When VIO rises faster than VDD, which can happen when VREGIN and VIO are tied together, a
delay created between GPIO power (VIO) and the logic controlling GPIO (VDD) results in a
temporary unknown state at the GPIO pins. When VIO rises faster than VDD, the GPIO may enter
the following states: floating, glitch low, or glitch high. Cross coupling VIO and VDD with a 4.7 µF
capacitor mitigates the root cause of the problem by allowing VIO and VDD to rise at the same rate.
On exit from the reset state, the program counter (PC) is reset, and the system clock defaults to the internal oscillator. The Watchdog Timer is enabled with the system clock divided by 12 as its clock source. Program execution begins at location 0x0000.
VDD
Power On
Reset
Supply
Monitor
'0'
Enable
(wired-OR)
/RST
+
C0RSEF
Missing
Clock
Detector
(oneshot)
EN
Reset
Funnel
PCA
WDT
(Software Reset)
SWRSF
Errant
FLASH
Operation
EN
System
Clock
WDT
Enable
Px.x
+
-
Comparator 0
MCD
Enable
Px.x
CIP-51
Microcontroller
Core
System Reset
Extended Interrupt
Handler
Figure 16.1. Reset Sources
Rev. 1.2
138
C8051F55x/56x/57x
16.1. Power-On Reset
During power-up, the device is held in a reset state and the RST pin is driven low until VDD settles above
VRST. A delay occurs before the device is released from reset; the delay decreases as the VDD ramp time
increases (VDD ramp time is defined as how fast VDD ramps from 0 V to VRST). Figure 16.2. plots the
power-on and VDD monitor reset timing.
On exit from a power-on reset, the PORSF flag (RSTSRC.1) is set by hardware to logic 1. When PORSF is
set, all of the other reset flags in the RSTSRC Register are indeterminate (PORSF is cleared by all other
resets). Since all resets cause program execution to begin at the same location (0x0000) software can
read the PORSF flag to determine if a power-up was the cause of reset. The content of internal data memory should be assumed to be undefined after a power-on reset. The VDD monitor is enabled following a
power-on reset.
volts
Note: For devices with a date code before year 2011, work week 24 (1124), if the /RST pin is held low for
more than 1 second while power is applied to the device, and then /RST is released, a percentage
of devices may lock up and fail to execute code. Toggling the /RST pin does not clear the condition.
The condition is cleared by cycling power. Most devices that are affected will show the lock up
behavior only within a narrow range of temperatures (a 5 to 10 °C window). Parts with a date code
of year 2011, work week 24 (1124) or later do not have any restrictions on /RST low time. The date
code of a device is a four-digit number on the bottom-most line of each device with the format
YYWW, where YY is the two-digit calendar year and WW is the two digit work week.
VDD
2.45
2.25
VRST
VD
D
2.0
1.0
t
Logic HIGH
/RST
TPORDelay
Logic LOW
VDD
Monitor
Reset
Power-On
Reset
Figure 16.2. Power-On and VDD Monitor Reset Timing
139
Rev. 1.2
C8051F55x/56x/57x
16.2. Power-Fail Reset/VDD Monitor
When a power-down transition or power irregularity causes VDD to drop below VRST, the power supply
monitor will drive the RST pin low and hold the CIP-51 in a reset state (see Figure 16.2). When VDD returns
to a level above VRST, the CIP-51 will be released from the reset state. Note that even though internal data
memory contents are not altered by the power-fail reset, it is impossible to determine if VDD dropped below
the level required for data retention. If the PORSF flag reads 1, the data may no longer be valid. The VDD
monitor is enabled after power-on resets. Its defined state (enabled/disabled) is not altered by any other
reset source. For example, if the VDD monitor is disabled by code and a software reset is performed, the
VDD monitor will still be disabled after the reset. To protect the integrity of Flash contents, the VDD
monitor must be enabled to the higher setting (VDMLVL = 1) and selected as a reset source if software contains routines which erase or write Flash memory. If the VDD monitor is not enabled and
set to the high level, any erase or write performed on Flash memory will cause a Flash Error device
reset.
Important Note: If the VDD monitor is being turned on from a disabled state, it should be enabled before it
is selected as a reset source. Selecting the VDD monitor as a reset source before it is enabled and stabilized may cause a system reset. In some applications, this reset may be undesirable. If this is not desirable
in the application, a delay should be introduced between enabling the monitor and selecting it as a reset
source. The procedure for enabling the VDD monitor and configuring it as a reset source from a disabled
state is as follows:
1. Enable the VDD monitor (VDMEN bit in VDM0CN = 1).
2. If necessary, wait for the VDD monitor to stabilize (see Table 5.4 for the VDD Monitor turn-on time).
Note: This delay should be omitted if software contains routines that erase or write Flash
memory.
3. Select the VDD monitor as a reset source (PORSF bit in RSTSRC = 1).
See Figure 16.2 for VDD monitor timing; note that the power-on-reset delay is not incurred after a VDD
monitor reset. See Table 5.4 for complete electrical characteristics of the VDD monitor.
Note: The output of the internal voltage regulator is calibrated by the MCU immediately after any reset
event. The output of the un-calibrated internal regulator could be below the high threshold setting of
the VDD Monitor. If this is the case and the VDD Monitor is set to the high threshold setting and if the
MCU receives a non-power on reset (POR), the MCU will remain in reset until a POR occurs (i.e.,
VDD Monitor will keep the device in reset). A POR will force the VDD Monitor to the low threshold
setting which is guaranteed to be below the un-calibrated output of the internal regulator. The device
will then exit reset and resume normal operation. It is for this reason Silicon Labs strongly
recommends that the VDD Monitor is always left in the low threshold setting (i.e. default value upon
POR).
When programming the Flash in-system, the VDD Monitor must be set to the high threshold setting. For the
highest system reliability, the time the VDD Monitor is set to the high threshold setting should be minimized
(e.g., setting the VDD Monitor to the high threshold setting just before the Flash write operation and then
changing it back to the low threshold setting immediately after the Flash write operation).
Note: The VDD Monitor may trigger on fast changes in voltage on the VDD pin, regardless of whether the
voltage increased or decreased.
Rev. 1.2
140
C8051F55x/56x/57x
SFR Definition 16.1. VDM0CN: VDD Monitor Control
Bit
7
6
5
4
3
2
1
0
Name
VDMEN
VDDSTAT
VDMLVL
Type
R/W
R
R/W
R
R
R
R
R
Reset
Varies
Varies
0
0
0
0
0
0
SFR Address = 0xFF; SFR Page = 0x00
Bit
Name
7
VDMEN
Function
VDD Monitor Enable.
This bit turns the VDD monitor circuit on/off. The VDD Monitor cannot generate system resets until it is also selected as a reset source in register RSTSRC (SFR Definition 16.2). Selecting the VDD monitor as a reset source before it has stabilized
may generate a system reset. In systems where this reset would be undesirable, a
delay should be introduced between enabling the VDD Monitor and selecting it as a
reset source. See Table 5.4 for the minimum VDD Monitor turn-on time.
0: VDD Monitor Disabled.
1: VDD Monitor Enabled.
6
VDDSTAT
VDD Status.
This bit indicates the current power supply status (VDD Monitor output).
0: VDD is at or below the VDD monitor threshold.
1: VDD is above the VDD monitor threshold.
5
VDMLVL
VDD Monitor Level Select.
0: VDD Monitor Threshold is set to VRST-LOW
1: VDD Monitor Threshold is set to VRST-HIGH. This setting is required for any system includes code that writes to and/or erases Flash.
4:0
Unused
Read = 00000b; Write = Don’t care.
16.3. External Reset
The external RST pin provides a means for external circuitry to force the device into a reset state. Asserting an active-low signal on the RST pin generates a reset; an external pullup and/or decoupling of the RST
pin may be necessary to avoid erroneous noise-induced resets. See Table 5.4 for complete RST pin specifications. The PINRSF flag (RSTSRC.0) is set on exit from an external reset.
16.4. Missing Clock Detector Reset
The Missing Clock Detector (MCD) is a one-shot circuit that is triggered by the system clock. If the system
clock remains high or low for more than the value specified in Table 5.4, “Reset Electrical Characteristics,”
on page 41, the one-shot will time out and generate a reset. After a MCD reset, the MCDRSF flag
(RSTSRC.2) will read 1, signifying the MCD as the reset source; otherwise, this bit reads 0. Writing a 1 to
the MCDRSF bit enables the Missing Clock Detector; writing a 0 disables it. The state of the RST pin is
unaffected by this reset.
141
Rev. 1.2
C8051F55x/56x/57x
16.5. Comparator0 Reset
Comparator0 can be configured as a reset source by writing a 1 to the C0RSEF flag (RSTSRC.5). Comparator0 should be enabled and allowed to settle prior to writing to C0RSEF to prevent any turn-on chatter
on the output from generating an unwanted reset. The Comparator0 reset is active-low: if the non-inverting
input voltage (on CP0+) is less than the inverting input voltage (on CP0–), the device is put into the reset
state. After a Comparator0 reset, the C0RSEF flag (RSTSRC.5) will read 1 signifying Comparator0 as the
reset source; otherwise, this bit reads 0. The state of the RST pin is unaffected by this reset.
16.6. PCA Watchdog Timer Reset
The programmable Watchdog Timer (WDT) function of the Programmable Counter Array (PCA) can be
used to prevent software from running out of control during a system malfunction. The PCA WDT function
can be enabled or disabled by software as described in Section “26.4. Watchdog Timer Mode” on
page 291; the WDT is enabled and clocked by SYSCLK/12 following any reset. If a system malfunction
prevents user software from updating the WDT, a reset is generated and the WDTRSF bit (RSTSRC.5) is
set to 1. The state of the RST pin is unaffected by this reset.
16.7. Flash Error Reset
If a Flash read/write/erase or program read targets an illegal address, a system reset is generated. This
may occur due to any of the following:
A Flash write or erase is attempted above user code space. This occurs when PSWE is set to 1 and a
MOVX write operation targets an address in or above the reserved space.
A Flash read is attempted above user code space. This occurs when a MOVC operation targets an
address in or above the reserved space.
A Program read is attempted above user code space. This occurs when user code attempts to branch
to an address in or above the reserved space.
A Flash read, write or erase attempt is restricted due to a Flash security setting (see Section
“14.3. Security Options” on page 127).
A Flash read, write, or erase is attempted when the VDD Monitor is not enabled to the high threshold
and set as a reset source.
The FERROR bit (RSTSRC.6) is set following a Flash error reset. The state of the RST pin is unaffected by
this reset.
16.8. Software Reset
Software may force a reset by writing a 1 to the SWRSF bit (RSTSRC.4). The SWRSF bit will read 1 following a software forced reset. The state of the RST pin is unaffected by this reset.
Rev. 1.2
142
C8051F55x/56x/57x
SFR Definition 16.2. RSTSRC: Reset Source
Bit
7
Name
6
5
4
3
2
1
0
FERROR
C0RSEF
SWRSF
WDTRSF
MCDRSF
PORSF
PINRSF
Type
R
R
R/W
R/W
R
R/W
R/W
R
Reset
0
Varies
Varies
Varies
Varies
Varies
Varies
Varies
SFR Address = 0xEF; SFR Page = 0x00
Bit
Name
Description
7
Unused
Unused.
Write
Read
Don’t care.
0
Set to 1 if Flash
read/write/erase error
caused the last reset.
6
FERROR Flash Error Reset Flag.
N/A
5
C0RSEF Comparator0 Reset Enable
and Flag.
Writing a 1 enables Com- Set to 1 if Comparator0
parator0 as a reset source caused the last reset.
(active-low).
4
SWRSF
Writing a 1 forces a system reset.
Software Reset Force and
Flag.
3
WDTRSF Watchdog Timer Reset Flag. N/A
2
MCDRSF Missing Clock Detector
Enable and Flag.
Set to 1 if Watchdog Timer
overflow caused the last
reset.
Set to 1 if Missing Clock
Writing a 1 enables the
Detector timeout caused
Missing Clock Detector.
The MCD triggers a reset the last reset.
if a missing clock condition
is detected.
1
PORSF
Power-On/VDD Monitor
Writing a 1 enables the
Reset Flag, and VDD monitor VDD monitor as a reset
source.
Reset Enable.
Writing 1 to this bit
before the VDD monitor
is enabled and stabilized
may cause a system
reset.
0
PINRSF
HW Pin Reset Flag.
N/A
Note: Do not use read-modify-write operations on this register
143
Set to 1 if last reset was
caused by a write to
SWRSF.
Rev. 1.2
Set to 1 anytime a poweron or VDD monitor reset
occurs.
When set to 1 all other
RSTSRC flags are indeterminate.
Set to 1 if RST pin caused
the last reset.
C8051F55x/56x/57x
17. External Data Memory Interface and On-Chip XRAM
For C8051F55x/56x/57x devices, 2 kB of RAM are included on-chip and mapped into the external data
memory space (XRAM). Additionally, an External Memory Interface (EMIF) is available on the C8051F5689 and ‘F570-5 devices, which can be used to access off-chip data memories and memory-mapped devices
connected to the GPIO ports. The external memory space may be accessed using the external move
instruction (MOVX) and the data pointer (DPTR), or using the MOVX indirect addressing mode using R0 or
R1. If the MOVX instruction is used with an 8-bit address operand (such as @R1), then the high byte of the
16-bit address is provided by the External Memory Interface Control Register (EMI0CN, shown in SFR
Definition 17.1).
Note: The MOVX instruction can also be used for writing to the Flash memory. See Section “14. Flash Memory” on
page 124 for details. The MOVX instruction accesses XRAM by default.
17.1. Accessing XRAM
The XRAM memory space is accessed using the MOVX instruction. The MOVX instruction has two forms,
both of which use an indirect addressing method. The first method uses the Data Pointer, DPTR, a 16-bit
register which contains the effective address of the XRAM location to be read from or written to. The second method uses R0 or R1 in combination with the EMI0CN register to generate the effective XRAM
address. Examples of both of these methods are given below.
17.1.1. 16-Bit MOVX Example
The 16-bit form of the MOVX instruction accesses the memory location pointed to by the contents of the
DPTR register. The following series of instructions reads the value of the byte at address 0x1234 into the
accumulator A:
MOV
MOVX
DPTR, #1234h
A, @DPTR
; load DPTR with 16-bit address to read (0x1234)
; load contents of 0x1234 into accumulator A
The above example uses the 16-bit immediate MOV instruction to set the contents of DPTR. Alternately,
the DPTR can be accessed through the SFR registers DPH, which contains the upper 8-bits of DPTR, and
DPL, which contains the lower 8-bits of DPTR.
17.1.2. 8-Bit MOVX Example
The 8-bit form of the MOVX instruction uses the contents of the EMI0CN SFR to determine the upper 8-bits
of the effective address to be accessed and the contents of R0 or R1 to determine the lower 8-bits of the
effective address to be accessed. The following series of instructions read the contents of the byte at
address 0x1234 into the accumulator A.
MOV
MOV
MOVX
EMI0CN, #12h
R0, #34h
a, @R0
; load high byte of address into EMI0CN
; load low byte of address into R0 (or R1)
; load contents of 0x1234 into accumulator A
Rev. 1.2
144
C8051F55x/56x/57x
17.2. Configuring the External Memory Interface
Configuring the External Memory Interface consists of four steps:
1. Configure the Output Modes of the associated port pins as either push-pull or open-drain (push-pull is
most common), and skip the associated pins in the crossbar.
2. Configure Port latches to “park” the EMIF pins in a dormant state (usually by setting them to logic 1).
3. Select the memory mode (on-chip only, split mode without bank select, split mode with bank select, or
off-chip only).
4. Set up timing to interface with off-chip memory or peripherals.
Each of these four steps is explained in detail in the following sections. The Port selection and Mode bits
are located in the EMI0CF register shown in SFR Definition .
17.3. Port Configuration
The External Memory Interface appears on Ports 1, 2 and 3 when it is used for off-chip memory access.
These ports are multiplexed so that low-order address lines are shared with the data lines. When the EMIF
is used, the Crossbar should be configured to skip over the /RD control line (P1.6) and the /WR control line
(P1.7) using the P1SKIP register and also skip over the ALE control line (P1.5). For more information
about configuring the Crossbar, see Section “19.6. Special Function Registers for Accessing and Configuring Port I/O” on page 183. The EMIF pinout is shown inTable 17.1 on page 146.
The External Memory Interface claims the associated Port pins for memory operations ONLY during the
execution of an off-chip MOVX instruction. Once the MOVX instruction has completed, control of the Port
pins reverts to the Port latches or to the Crossbar settings for those pins. See Section “19. Port Input/Output” on page 169 for more information about the Crossbar and Port operation and configuration. The Port
latches should be explicitly configured to “park” the External Memory Interface pins in a dormant
state, most commonly by setting them to a logic 1.
During the execution of the MOVX instruction, the External Memory Interface will explicitly disable the drivers on all Port pins that are acting as Inputs (Data[7:0] during a READ operation, for example). The Output
mode of the Port pins (whether the pin is configured as Open-Drain or Push-Pull) is unaffected by the
External Memory Interface operation, and remains controlled by the PnMDOUT registers. In most cases,
the output modes of all EMIF pins should be configured for push-pull mode.
145
Rev. 1.2
C8051F55x/56x/57x
Table 17.1. EMIF Pinout (C8051F568-9 and ‘F570-5)
Multiplexed Mode
Signal Name
Port Pin
RD
P1.6
WR
P1.7
ALE
P1.5
D0/A0
P3.0
D1/A1
P3.1
D2/A2
P3.2
D3/A3
P3.3
D4/A4
P3.4
D5/A5
P3.5
D6/A6
P3.6
D7/A7
P3.7
A8
P2.0
A9
P2.1
A10
P2.2
A11
P2.3
A12
P2.4
A13
P2.5
A14
P2.6
A15
P2.7
Rev. 1.2
146
C8051F55x/56x/57x
SFR Definition 17.1. EMI0CN: External Memory Interface Control
Bit
7
6
5
4
3
Name
PGSEL[7:0]
Type
R/W
Reset
0
0
0
0
SFR Address = 0xAA; SFR Page = 0x00
Bit
Name
0
2
1
0
0
0
0
Function
7:0 PGSEL[7:0] XRAM Page Select Bits.
The XRAM Page Select Bits provide the high byte of the 16-bit external data memory
address when using an 8-bit MOVX command, effectively selecting a 256-byte page of
RAM.
0x00: 0x0000 to 0x00FF
0x01: 0x0100 to 0x01FF
...
0xFE: 0xFE00 to 0xFEFF
0xFF: 0xFF00 to 0xFFFF
147
Rev. 1.2
C8051F55x/56x/57x
SFR Definition 17.2. EMI0CF: External Memory Configuration
Bit
7
6
5
4
3
Reserved
Name
1
EMD[1:0]
0
EALE[1:0]
R/W
Type
Reset
2
0
0
0
0
0
SFR Address = 0xB2; SFR Page = 0x0F
Bit
Name
0
1
1
Function
7:5
Unused
Read = 000b; Write = Don’t Care.
4
Reserved
Read = 0b; Must Write 0b.
3:2
EMD[1:0]
EMIF Operating Mode Select Bits.
00: Internal Only: MOVX accesses on-chip XRAM only. All effective addresses alias to
on-chip memory space
01: Split Mode without Bank Select: Accesses below the 2 kB boundary are directed
on-chip. Accesses above the 2 kB boundary are directed off-chip. 8-bit off-chip MOVX
operations use current contents of the Address high port latches to resolve the upper
address byte. To access off chip space, EMI0CN must be set to a page that is not contained in the on-chip address space.
10: Split Mode with Bank Select: Accesses below the 2 kB boundary are directed onchip. Accesses above the 2 kB boundary are directed off-chip. 8-bit off-chip MOVX
operations uses the contents of EMI0CN to determine the high-byte of the address.
11: External Only: MOVX accesses off-chip XRAM only. On-chip XRAM is not visible to
the CPU.
1:0
EALE[1:0]
ALE Pulse-Width Select Bits.
These bits only have an effect when EMD2 = 0.
00: ALE high and ALE low pulse width = 1 SYSCLK cycle.
01: ALE high and ALE low pulse width = 2 SYSCLK cycles.
10: ALE high and ALE low pulse width = 3 SYSCLK cycles.
11: ALE high and ALE low pulse width = 4 SYSCLK cycles.
Rev. 1.2
148
C8051F55x/56x/57x
17.4. Multiplexed Mode
The External Memory Interface operates only in a Multiplexed mode. In Multiplexed mode, the Data Bus
and the lower 8-bits of the Address Bus share the same Port pins: AD[7:0]. In this mode, an external latch
(74HC373 or equivalent logic gate) is used to hold the lower 8-bits of the RAM address. The external latch
is controlled by the ALE (Address Latch Enable) signal, which is driven by the External Memory Interface
logic. An example of a Multiplexed Configuration is shown in Figure 17.1.
In Multiplexed mode, the external MOVX operation can be broken into two phases delineated by the state
of the ALE signal. During the first phase, ALE is high and the lower 8-bits of the Address Bus are presented to AD[7:0]. During this phase, the address latch is configured such that the Q outputs reflect the
states of the ‘D’ inputs. When ALE falls, signaling the beginning of the second phase, the address latch
outputs remain fixed and are no longer dependent on the latch inputs. Later in the second phase, the Data
Bus controls the state of the AD[7:0] port at the time RD or WR is asserted.
See Section “17.6.1. Multiplexed Mode” on page 153 for more information.
A[15:8]
ADDRESS BUS
A[15:8]
74HC373
E
M
I
F
ALE
AD[7:0]
G
ADDRESS/DATA BUS
D
Q
A[7:0]
VDD
64 K X 8
SRAM
(Optional)
8
I/O[7:0]
CE
WE
OE
/WR
/RD
Figure 17.1. Multiplexed Configuration Example
149
Rev. 1.2
C8051F55x/56x/57x
17.5. Memory Mode Selection
The external data memory space can be configured in one of four modes, shown in Figure 17.2, based on
the EMIF Mode bits in the EMI0CF register (SFR Definition 17.2). These modes are summarized below.
More information about the different modes can be found in Section “17.6. Timing” on page 151.
EMI0CF[3:2] = 00
EMI0CF[3:2] = 01
0xFFFF
EMI0CF[3:2] = 10
0xFFFF
EMI0CF[3:2] = 11
0xFFFF
0xFFFF
On-Chip XRAM
On-Chip XRAM
Off-Chip
Memory
(No Bank Select)
Off-Chip
Memory
(Bank Select)
On-Chip XRAM
Off-Chip
Memory
On-Chip XRAM
On-Chip XRAM
On-Chip XRAM
On-Chip XRAM
On-Chip XRAM
0x0000
0x0000
0x0000
0x0000
Figure 17.2. EMIF Operating Modes
17.5.1. Internal XRAM Only
When bits EMI0CF[3:2] are set to 00, all MOVX instructions will target the internal XRAM space on the
device. Memory accesses to addresses beyond the populated space will wrap on 2 kB boundaries. As an
example, the addresses 0x800 and 0x1000 both evaluate to address 0x0000 in on-chip XRAM space.
8-bit MOVX operations use the contents of EMI0CN to determine the high-byte of the effective address
and R0 or R1 to determine the low-byte of the effective address.
16-bit MOVX operations use the contents of the 16-bit DPTR to determine the effective address.
17.5.2. Split Mode without Bank Select
When bit EMI0CF.[3:2] are set to 01, the XRAM memory map is split into two areas, on-chip space and offchip space.
Effective addresses below the internal XRAM size boundary will access on-chip XRAM space.
Effective addresses above the internal XRAM size boundary will access off-chip space.
8-bit MOVX operations use the contents of EMI0CN to determine whether the memory access is onchip or off-chip. However, in the “No Bank Select” mode, an 8-bit MOVX operation will not drive the
upper 8-bits A[15:8] of the Address Bus during an off-chip access. This allows the user to manipulate
the upper address bits at will by setting the Port state directly via the port latches. This behavior is in
contrast with “Split Mode with Bank Select” described below. The lower 8-bits of the Address Bus A[7:0]
are driven, determined by R0 or R1.
16-bit MOVX operations use the contents of DPTR to determine whether the memory access is on-chip
or off-chip, and unlike 8-bit MOVX operations, the full 16-bits of the Address Bus A[15:0] are driven
during the off-chip transaction.
Rev. 1.2
150
C8051F55x/56x/57x
17.5.3. Split Mode with Bank Select
When EMI0CF[3:2] are set to 10, the XRAM memory map is split into two areas, on-chip space and offchip space.
Effective addresses below the internal XRAM size boundary will access on-chip XRAM space.
Effective addresses above the internal XRAM size boundary will access off-chip space.
8-bit MOVX operations use the contents of EMI0CN to determine whether the memory access is onchip or off-chip. The upper 8-bits of the Address Bus A[15:8] are determined by EMI0CN, and the lower
8-bits of the Address Bus A[7:0] are determined by R0 or R1. All 16-bits of the Address Bus A[15:0] are
driven in “Bank Select” mode.
16-bit MOVX operations use the contents of DPTR to determine whether the memory access is on-chip
or off-chip, and the full 16-bits of the Address Bus A[15:0] are driven during the off-chip transaction.
17.5.4. External Only
When EMI0CF[3:2] are set to 11, all MOVX operations are directed to off-chip space. On-chip XRAM is not
visible to the CPU. This mode is useful for accessing off-chip memory located between 0x0000 and the
internal XRAM size boundary.
8-bit MOVX operations ignore the contents of EMI0CN. The upper Address bits A[15:8] are not driven
(identical behavior to an off-chip access in “Split Mode without Bank Select” described above). This
allows the user to manipulate the upper address bits at will by setting the Port state directly. The lower
8-bits of the effective address A[7:0] are determined by the contents of R0 or R1.
16-bit MOVX operations use the contents of DPTR to determine the effective address A[15:0]. The full
16-bits of the Address Bus A[15:0] are driven during the off-chip transaction.
17.6. Timing
The timing parameters of the External Memory Interface can be configured to enable connection to
devices having different setup and hold time requirements. The Address Setup time, Address Hold time,
RD and WR strobe widths, and in multiplexed mode, the width of the ALE pulse are all programmable in
units of SYSCLK periods through EMI0TC, shown in SFR Definition 17.3, and EMI0CF[1:0].
The timing for an off-chip MOVX instruction can be calculated by adding 4 SYSCLK cycles to the timing
parameters defined by the EMI0TC register. Assuming non-multiplexed operation, the minimum execution
time for an off-chip XRAM operation is 5 SYSCLK cycles (1 SYSCLK for RD or WR pulse + 4 SYSCLKs).
For multiplexed operations, the Address Latch Enable signal will require a minimum of 2 additional
SYSCLK cycles. Therefore, the minimum execution time for an off-chip XRAM operation in multiplexed
mode is 7 SYSCLK cycles (2 for /ALE + 1 for RD or WR + 4). The programmable setup and hold times
default to the maximum delay settings after a reset. Table 17.2 lists the ac parameters for the External
Memory Interface, and Figure 17.3 through Figure 17.5 show the timing diagrams for the different External
Memory Interface modes and MOVX operations.
151
Rev. 1.2
C8051F55x/56x/57x
SFR Definition 17.3. EMI0TC: External Memory Timing Control
Bit
7
6
5
4
3
2
1
0
Name
EAS[1:0]
EWR[3:0]
EAH[1:0]
Type
R/W
R/W
R/W
Reset
1
1
1
1
1
1
1
1
SFR Address = 0xAA; SFR Page = 0x0F
Bit
Name
Function
7:6
EAS[1:0]
EMIF Address Setup Time Bits.
00: Address setup time = 0 SYSCLK cycles.
01: Address setup time = 1 SYSCLK cycle.
10: Address setup time = 2 SYSCLK cycles.
11: Address setup time = 3 SYSCLK cycles.
5:2
EWR[3:0]
EMIF WR and RD Pulse-Width Control Bits.
0000: WR and RD pulse width = 1 SYSCLK cycle.
0001: WR and RD pulse width = 2 SYSCLK cycles.
0010: WR and RD pulse width = 3 SYSCLK cycles.
0011: WR and RD pulse width = 4 SYSCLK cycles.
0100: WR and RD pulse width = 5 SYSCLK cycles.
0101: WR and RD pulse width = 6 SYSCLK cycles.
0110: WR and RD pulse width = 7 SYSCLK cycles.
0111: WR and RD pulse width = 8 SYSCLK cycles.
1000: WR and RD pulse width = 9 SYSCLK cycles.
1001: WR and RD pulse width = 10 SYSCLK cycles.
1010: WR and RD pulse width = 11 SYSCLK cycles.
1011: WR and RD pulse width = 12 SYSCLK cycles.
1100: WR and RD pulse width = 13 SYSCLK cycles.
1101: WR and RD pulse width = 14 SYSCLK cycles.
1110: WR and RD pulse width = 15 SYSCLK cycles.
1111: WR and RD pulse width = 16 SYSCLK cycles.
1:0
EAH[1:0]
EMIF Address Hold Time Bits.
00: Address hold time = 0 SYSCLK cycles.
01: Address hold time = 1 SYSCLK cycle.
10: Address hold time = 2 SYSCLK cycles.
11: Address hold time = 3 SYSCLK cycles.
Rev. 1.2
152
C8051F55x/56x/57x
17.6.1. Multiplexed Mode
17.6.1.1. 16-bit MOVX: EMI0CF[4:2] = 001, 010, or 011
Muxed 16-bit WRITE
ADDR[15:8]
AD[7:0]
EMIF ADDRESS (8 MSBs) from DPH
EMIF ADDRESS (8 LSBs) from
DPL
T
ALEH
EMIF WRITE DATA
T
ALEL
ALE
T
T
WDS
T
ACS
WDH
T
T
ACW
ACH
WR
RD
Muxed 16-bit READ
ADDR[15:8]
AD[7:0]
EMIF ADDRESS (8 MSBs) from DPH
EMIF ADDRESS (8 LSBs) from
DPL
T
ALEH
EMIF READ DATA
T
T
ALEL
RDS
T
RDH
ALE
T
ACS
T
ACW
RD
WR
Figure 17.3. Multiplexed 16-bit MOVX Timing
153
Rev. 1.2
T
ACH
C8051F55x/56x/57x
17.6.1.2. 8-bit MOVX without Bank Select: EMI0CF[4:2] = 001 or 011
Muxed 8-bit WRITE Without Bank Select
ADDR[15:8]
AD[7:0]
EMIF ADDRESS (8 LSBs) from
R0 or R1
T
ALEH
EMIF WRITE DATA
T
ALEL
ALE
T
T
WDS
T
ACS
WDH
T
T
ACW
ACH
WR
RD
Muxed 8-bit READ Without Bank Select
ADDR[15:8]
AD[7:0]
EMIF ADDRESS (8 LSBs) from
R0 or R1
T
ALEH
EMIF READ DATA
T
T
ALEL
RDS
T
RDH
ALE
T
ACS
T
ACW
T
ACH
RD
WR
Figure 17.4. Multiplexed 8-bit MOVX without Bank Select Timing
Rev. 1.2
154
C8051F55x/56x/57x
17.6.1.3. 8-bit MOVX with Bank Select: EMI0CF[4:2] = 010
Muxed 8-bit WRITE with Bank Select
ADDR[15:8]
AD[7:0]
EMIF ADDRESS (8 MSBs) from EMI0CN
EMIF ADDRESS (8 LSBs) from
R0 or R1
T
ALEH
EMIF WRITE DATA
T
ALEL
ALE
T
T
WDS
T
ACS
WDH
T
T
ACW
ACH
WR
RD
Muxed 8-bit READ with Bank Select
ADDR[15:8]
AD[7:0]
EMIF ADDRESS (8 MSBs) from EMI0CN
EMIF ADDRESS (8 LSBs) from
R0 or R1
T
ALEH
EMIF READ DATA
T
T
ALEL
RDS
T
RDH
ALE
T
ACS
T
ACW
T
ACH
RD
WR
Figure 17.5. Multiplexed 8-bit MOVX with Bank Select Timing
155
Rev. 1.2
C8051F55x/56x/57x
Table 17.2. AC Parameters for External Memory Interface
Parameter
Description
Min*
Max*
Units
TACS
Address/Control Setup Time
0
3 x TSYSCLK
ns
TACW
Address/Control Pulse Width
1 x TSYSCLK
16 x TSYSCLK
ns
TACH
Address/Control Hold Time
0
3 x TSYSCLK
ns
TALEH
Address Latch Enable High Time
1 x TSYSCLK
4 x TSYSCLK
ns
TALEL
Address Latch Enable Low Time
1 x TSYSCLK
4 x TSYSCLK
ns
TWDS
Write Data Setup Time
1 x TSYSCLK
19 x TSYSCLK
ns
TWDH
Write Data Hold Time
0
3 x TSYSCLK
ns
TRDS
Read Data Setup Time
20
ns
TRDH
Read Data Hold Time
0
ns
*Note: TSYSCLK is equal to one period of the device system clock (SYSCLK).
Rev. 1.2
156
C8051F55x/56x/57x
18. Oscillators and Clock Selection
C8051F55x/56x/57x devices include a programmable internal high-frequency oscillator, an external oscillator drive circuit, and a clock multiplier. The internal oscillator can be enabled/disabled and calibrated
using the OSCICN, OSCICRS, and OSCIFIN registers, as shown in Figure 18.1. The system clock can be
sourced by the external oscillator circuit or the internal oscillator. The clock multiplier can produce three
possible base outputs which can be scaled by a programmable factor of 1, 2/3, 2/4 (or 1/2), 2/5, 2/6 (or
1/3), or 2/7: Internal Oscillator x 2, Internal Oscillator x 4, External Oscillator x 2, or External Oscillator x 4.
OSCICN
IFCN2
IFCN1
IFCN0
CLKSEL
SEL1
SEL0
OSCIFIN
IOSCEN
IFRDY
SUSPEND
OSCICRS
Option 3
XTAL2
CAL
EN
IOSC
n
Programmable Internal
Clock Generator
Option 4
XTAL2
CLOCK MULTIPLIER
IOSC / 2
EXOSC / 2
IOSC
EXTOSC
Option 2
VDD
Option 1
x4
n
SYSCLK
XTAL1
XTAL2
Input
Circuit
10MΩ
OSC
EXOSC
MULEN
MULINIT
MULRDY
MULDIV2
MULDIV1
MULDIV0
MULSEL1
MULSEL0
XFCN2
XFCN1
XFCN0
XTLVLD
XOSCMD2
XOSCMD1
XOSCMD0
XTAL2
OSCXCN
CLKMUL
Figure 18.1. Oscillator Options
18.1. System Clock Selection
The CLKSL[1:0] bits in register CLKSEL select which oscillator source is used as the system clock.
CLKSL[1:0] must be set to 01b for the system clock to run from the external oscillator; however the external oscillator may still clock certain peripherals (timers, PCA) when the internal oscillator is selected as the
system clock. The system clock may be switched on-the-fly between the internal oscillator, external oscillator, and Clock Multiplier so long as the selected clock source is enabled and has settled.
The internal oscillator requires little start-up time and may be selected as the system clock immediately following the register write which enables the oscillator. The external RC and C modes also typically require
no startup time.
External crystals and ceramic resonators however, typically require a start-up time before they are settled
and ready for use. The Crystal Valid Flag (XTLVLD in register OSCXCN) is set to 1 by hardware when the
external crystal or ceramic resonator is settled. In crystal mode, to avoid reading a false XTLVLD, software should delay at least 1 ms between enabling the external oscillator and checking XTLVLD.
Rev. 1.2
157
C8051F55x/56x/57x
SFR Definition 18.1. CLKSEL: Clock Select
Bit
7
6
5
4
3
2
0
CLKSL[1:0]
Name
Type
R
R
R
R
R
R
Reset
0
0
0
0
0
0
SFR Address = 0x8F; SFR Page = 0x0F
Bit
Name
7:2
1:0
1
R/W
0
0
Function
Unused
Read = 000000b; Write = Don’t Care
CLKSL[1:0] System Clock Source Select Bits.
00: SYSCLK derived from the Internal Oscillator and scaled per the IFCN bits in register OSCICN.
01: SYSCLK derived from the External Oscillator circuit.
10: SYSCLK derived from the Clock Multiplier.
11: reserved.
158
Rev. 1.2
C8051F55x/56x/57x
18.2. Programmable Internal Oscillator
All C8051F55x/56x/57x devices include a programmable internal high-frequency oscillator that defaults as
the system clock after a system reset. The internal oscillator period can be adjusted via the OSCICRS and
OSCIFIN registers defined in SFR Definition 18.3 and SFR Definition 18.4. On C8051F55x/56x/57x
devices, OSCICRS and OSCIFIN are factory calibrated to obtain a 24 MHz base frequency. Note that the
system clock may be derived from the programmed internal oscillator divided by 1, 2, 4, 8, 16, 32, 64, or
128, as defined by the IFCN bits in register OSCICN. The divide value defaults to 128 following a reset.
18.2.1. Internal Oscillator Suspend Mode
When software writes a logic 1 to SUSPEND (OSCICN.5), the internal oscillator is suspended. If the system clock is derived from the internal oscillator, the input clock to the peripheral or CIP-51 will be stopped
until one of the following events occur:
Port 0 Match Event.
Port 1 Match Event.
Port 2 Match Event.
Port 3 Match Event.
Comparator 0 enabled and output is logic 0.
When one of the oscillator awakening events occur, the internal oscillator, CIP-51, and affected peripherals
resume normal operation, regardless of whether the event also causes an interrupt. The CPU resumes
execution at the instruction following the write to SUSPEND.
Note: Before entering suspend mode, firmware must set the ZTCEN bit in REF0CN (SFR Definition 7.1).
Rev. 1.2
159
C8051F55x/56x/57x
SFR Definition 18.2. OSCICN: Internal Oscillator Control
Bit
Name
7
6
IOSCEN[1:0]
5
4
3
SUSPEND
IFRDY
Reserved
IFCN[2:0]
R/W
Type
R/W
R/W
R/W
R
R
Reset
1
1
0
X
0
SFR Address = 0xA1; SFR Page = 0x0F
Bit
Name
2
0
1
0
0
0
Function
7:6 IOSCEN[1:0] Internal Oscillator Enable Bits.
00: Oscillator Disabled.
01: Reserved.
10: Reserved.
11: Oscillator enabled in normal mode and disabled in suspend mode.
5
SUSPEND
Internal Oscillator Suspend Enable Bit.
Setting this bit to logic 1 places the internal oscillator in SUSPEND mode. The internal oscillator resumes operation when one of the SUSPEND mode awakening
events occurs.
Before entering suspend mode, firmware must set the ZTCEN bit in REF0CN.
4
IFRDY
Internal Oscillator Frequency Ready Flag.
Note: This flag may not accurately reflect the state of the oscillator. Firmware should
not use this flag to determine if the oscillator is running.
0: Internal oscillator is not running at programmed frequency.
1: Internal oscillator is running at programmed frequency.
3
Reserved
Read = 0b; Must Write = 0b.
2:0
IFCN[2:0]
Internal Oscillator Frequency Divider Control Bits.
000: SYSCLK derived from Internal Oscillator divided by 128.
001: SYSCLK derived from Internal Oscillator divided by 64.
010: SYSCLK derived from Internal Oscillator divided by 32.
011: SYSCLK derived from Internal Oscillator divided by 16.
100: SYSCLK derived from Internal Oscillator divided by 8.
101: SYSCLK derived from Internal Oscillator divided by 4.
110: SYSCLK derived from Internal Oscillator divided by 2.
111: SYSCLK derived from Internal Oscillator divided by 1.
160
Rev. 1.2
C8051F55x/56x/57x
SFR Definition 18.3. OSCICRS: Internal Oscillator Coarse Calibration
Bit
7
6
5
4
3
2
1
0
Varies
Varies
Varies
OSCICRS[6:0]
Name
Type
R
Reset
0
R/W
Varies
Varies
Varies
SFR Address = 0xA2; SFR Page = 0x0F
Bit
Name
7
Unused
6:0
OSCICRS[6:0]
Varies
Function
Read = 0; Write = Don’t Care
Internal Oscillator Coarse Calibration Bits.
These bits determine the internal oscillator period. When set to 0000000b, the
internal oscillator operates at its slowest setting. When set to 1111111b, the internal oscillator operates at its fastest setting. The reset value is factory calibrated
to generate an internal oscillator frequency of 24 MHz.
SFR Definition 18.4. OSCIFIN: Internal Oscillator Fine Calibration
Bit
7
6
5
4
3
2
1
0
Varies
Varies
OSCIFIN[5:0]
Type
R
R
Reset
0
0
R/W
Varies
Varies
SFR Address = 0x9E; SFR Page = 0x0F
Bit
Name
7:6
5:0
Unused
Varies
Varies
Function
Read = 00b; Write = Don’t Care
OSCIFIN[5:0] Internal Oscillator Fine Calibration Bits.
These bits are fine adjustment for the internal oscillator period. The reset value is
factory calibrated to generate an internal oscillator frequency of 24 MHz.
Rev. 1.2
161
C8051F55x/56x/57x
162
Rev. 1.2
C8051F55x/56x/57x
18.3. Clock Multiplier
The Clock Multiplier generates an output clock which is 4 times the input clock frequency scaled by a programmable factor of 1, 2/3, 2/4 (or 1/2), 2/5, 2/6 (or 1/3), or 2/7. The Clock Multiplier’s input can be
selected from the external oscillator, or the internal or external oscillators divided by 2. This produces three
possible base outputs which can be scaled by a programmable factor: Internal Oscillator x 2, External
Oscillator x 2, or External Oscillator x 4. See Section 18.1 on page 157 for details on system clock selection.
The Clock Multiplier is configured via the CLKMUL register (SFR Definition 18.5). The procedure for configuring and enabling the Clock Multiplier is as follows:
1. Reset the Multiplier by writing 0x00 to register CLKMUL.
2. Select the Multiplier input source via the MULSEL bits.
3. Select the Multiplier output scaling factor via the MULDIV bits
4. Enable the Multiplier with the MULEN bit (CLKMUL | = 0x80).
5. Delay for >5 µs.
6. Initialize the Multiplier with the MULINIT bit (CLKMUL | = 0xC0).
7. Poll for MULRDY > 1.
Important Note: When using an external oscillator as the input to the Clock Multiplier, the external source
must be enabled and stable before the Multiplier is initialized. See “18.4. External Oscillator Drive Circuit”
on page 164 for details on selecting an external oscillator source.
The Clock Multiplier allows faster operation of the CIP-51 core and is intended to generate an output frequency between 25 and 50 MHz. The clock multiplier can also be used with slow input clocks. However, if
the clock is below the minimum Clock Multiplier input frequency (FCMmin), the generated clock will consist
of four fast pulses followed by a long delay until the next input clock rising edge. The average frequency of
the output is equal to 4x the input, but the instantaneous frequency may be faster. See Figure 18.2 below
for more information.
if FCM in >= FCM min
FCM in
FCM out
if FCMin < FCM min
FCM in
FCM out
Figure 18.2. Example Clock Multiplier Output
Rev. 1.2
162
C8051F55x/56x/57x
SFR Definition 18.5. CLKMUL: Clock Multiplier
Bit
7
6
5
4
3
Name
MULEN
MULINIT
MULRDY
MULDIV[2:0]
MULSEL[1:0]
Type
R/W
R/W
R
R/W
R/W
Reset
0
0
0
0
SFR Address = 0x97; SFR Page = 0x0F
Bit
Name
7
MULEN
0
2
1
0
0
0
0
Function
Clock Multiplier Enable.
0: Clock Multiplier disabled.
1: Clock Multiplier enabled.
6
MULINIT
Clock Multiplier Initialize.
This bit is 0 when the Clock Multiplier is enabled. Once enabled, writing a 1 to this
bit will initialize the Clock Multiplier. The MULRDY bit reads 1 when the Clock Multiplier is stabilized.
5
MULRDY
4:2
MULDIV[2:0]
1:0
MULSEL[1:0] Clock Multiplier Input Select.
Clock Multiplier Ready.
0: Clock Multiplier is not ready.
1: Clock Multiplier is ready (PLL is locked).
Clock Multiplier Output Scaling Factor.
000: Clock Multiplier Output scaled by a factor of 1.
001: Clock Multiplier Output scaled by a factor of 1.
010: Clock Multiplier Output scaled by a factor of 1.
011: Clock Multiplier Output scaled by a factor of 2/3*.
100: Clock Multiplier Output scaled by a factor of 2/4 (1/2).
101: Clock Multiplier Output scaled by a factor of 2/5*.
110: Clock Multiplier Output scaled by a factor of 2/6 (1/3).
111: Clock Multiplier Output scaled by a factor of 2/7*.
*Note: The Clock Multiplier output duty cycle is not 50% for these settings.
These bits select the clock supplied to the Clock Multiplier
MULSEL[1:0]
Selected Input Clock
Clock Multiplier Output
for MULDIV[2:0] = 000b
00
Internal Oscillator
Internal Oscillator x 2
01
External Oscillator
External Oscillator x 2
10
Internal Oscillator
Internal Oscillator x 4
11
External Oscillator
External Oscillator x 4
Notes:The maximum system clock is 50 MHz, and so the Clock Multiplier output should be scaled accordingly.
If Internal Oscillator x 2 or External Oscillator x 2 is selected using the MULSEL bits, MULDIV[2:0] is ignored.
163
Rev. 1.2
C8051F55x/56x/57x
18.4. External Oscillator Drive Circuit
The external oscillator circuit may drive an external crystal, ceramic resonator, capacitor, or RC network. A
CMOS clock may also provide a clock input. For a crystal or ceramic resonator configuration, the crystal/resonator must be wired across the XTAL1 and XTAL2 pins as shown in Option 1 of Figure 18.1. A
10 MΩ resistor also must be wired across the XTAL2 and XTAL1 pins for the crystal/resonator configuration. In RC, capacitor, or CMOS clock configuration, the clock source should be wired to the XTAL2 pin as
shown in Option 2, 3, or 4 of Figure 18.1. The type of external oscillator must be selected in the OSCXCN
register, and the frequency control bits (XFCN) must be selected appropriately (see SFR Definition 18.6).
Important Note on External Oscillator Usage: Port pins must be configured when using the external
oscillator circuit. When the external oscillator drive circuit is enabled in crystal/resonator mode, Port pins
P0.2 and P0.3 are used as XTAL1 and XTAL2 respectively. When the external oscillator drive circuit is
enabled in capacitor, RC, or CMOS clock mode, Port pin P0.3 is used as XTAL2. The Port I/O Crossbar
should be configured to skip the Port pins used by the oscillator circuit; see Section “19.3. Priority Crossbar
Decoder” on page 172 for Crossbar configuration. Additionally, when using the external oscillator circuit in
crystal/resonator, capacitor, or RC mode, the associated Port pins should be configured as analog inputs.
In CMOS clock mode, the associated pin should be configured as a digital input. See Section “19.4. Port
I/O Initialization” on page 174 for details on Port input mode selection.
Rev. 1.2
164
C8051F55x/56x/57x
SFR Definition 18.6. OSCXCN: External Oscillator Control
Bit
7
6
Name
XTLVLD
XOSCMD[2:0]
Type
R
R/W
Reset
0
0
5
0
4
3
XTLVLD
1
R
0
0
R/W
0
0
Function
Crystal Oscillator Valid Flag.
(Read only when XOSCMD = 11x.)
0: Crystal Oscillator is unused or not yet stable.
1: Crystal Oscillator is running and stable.
6:4
XOSCMD[2:0] External Oscillator Mode Select.
00x: External Oscillator circuit off.
010: External CMOS Clock Mode.
011: External CMOS Clock Mode with divide by 2 stage.
100: RC Oscillator Mode.
101: Capacitor Oscillator Mode.
110: Crystal Oscillator Mode.
111: Crystal Oscillator Mode with divide by 2 stage.
3
Unused
2:0
XFCN[2:0]
Read = 0b; Write =0b
External Oscillator Frequency Control Bits.
Set according to the desired frequency for Crystal or RC mode.
Set according to the desired K Factor for C mode.
165
0
XFCN[2:0]
SFR Address = 0x9F; SFR Page = 0x0F
Bit
Name
7
2
XFCN
Crystal Mode
RC Mode
C Mode
000
f ≤ 32 kHz
f ≤ 25 kHz
K Factor = 0.87
001
32 kHz < f ≤ 84 kHz
25 kHz < f ≤ 50 kHz
K Factor = 2.6
010
84 kHz < f ≤ 225 kHz
50 kHz < f ≤ 100 kHz
K Factor = 7.7
011
225 kHz < f ≤ 590 kHz
100 kHz < f ≤ 200 kHz
K Factor = 22
100
590 kHz < f ≤ 1.5 MHz 200 kHz < f ≤ 400 kHz
K Factor = 65
101
1.5 MHz < f ≤ 4 MHz
400 kHz < f ≤ 800 kHz
K Factor = 180
110
4 MHz < f ≤ 10 MHz
800 kHz < f ≤ 1.6 MHz
K Factor = 664
111
10 MHz < f ≤ 30 MHz
1.6 MHz < f ≤ 3.2 MHz
K Factor = 1590
Rev. 1.2
0
C8051F55x/56x/57x
18.4.1. External Crystal Example
If a crystal or ceramic resonator is used as an external oscillator source for the MCU, the circuit should be
configured as shown in Figure 18.1, Option 1. The External Oscillator Frequency Control value (XFCN)
should be chosen from the Crystal column of the table in SFR Definition 18.6 (OSCXCN register). For
example, an 11.0592 MHz crystal requires an XFCN setting of 111b and a 32.768 kHz Watch Crystal
requires an XFCN setting of 001b. After an external 32.768 kHz oscillator is stabilized, the XFCN setting
can be switched to 000 to save power. It is recommended to enable the missing clock detector before
switching the system clock to any external oscillator source.
When the crystal oscillator is first enabled, the oscillator amplitude detection circuit requires a settling time
to achieve proper bias. Introducing a delay of 1 ms between enabling the oscillator and checking the
XTLVLD bit will prevent a premature switch to the external oscillator as the system clock. Switching to the
external oscillator before the crystal oscillator has stabilized can result in unpredictable behavior. The recommended procedure is:
1. Force XTAL1 and XTAL2 to a high state. This involves enabling the Crossbar and writing 1 to the port
pins associated with XTAL1 and XTAL2.
2. Configure XTAL1 and XTAL2 as analog inputs using.
3. Enable the external oscillator.
4. Wait at least 1 ms.
5. Poll for XTLVLD => 1.
6. Enable the Missing Clock Detector.
7. Switch the system clock to the external oscillator.
Important Note on External Crystals: Crystal oscillator circuits are quite sensitive to PCB layout. The
crystal should be placed as close as possible to the XTAL pins on the device. The traces should be as
short as possible and shielded with ground plane from any other traces which could introduce noise or
interference.
The capacitors shown in the external crystal configuration provide the load capacitance required by the
crystal for correct oscillation. These capacitors are "in series" as seen by the crystal and "in parallel" with
the stray capacitance of the XTAL1 and XTAL2 pins.
Note: The desired load capacitance depends upon the crystal and the manufacturer. Refer to the crystal data sheet
when completing these calculations.
For example, a tuning-fork crystal of 32.768 kHz with a recommended load capacitance of 12.5 pF should
use the configuration shown in Figure 18.1, Option 1. The total value of the capacitors and the stray capacitance of the XTAL pins should equal 25 pF. With a stray capacitance of 3 pF per pin, the 22 pF capacitors
yield an equivalent capacitance of 12.5 pF across the crystal, as shown in Figure 18.3.
Rev. 1.2
166
C8051F55x/56x/57x
XTAL1
10MΩ
XTAL2
32.768 kHz
22pF*
22pF*
* Capacitor values depend on
crystal specifications
Figure 18.3. External 32.768 kHz Quartz Crystal Oscillator Connection Diagram
18.4.2. External RC Example
If an RC network is used as an external oscillator source for the MCU, the circuit should be configured as
shown in Figure 18.1, Option 2. The capacitor should be no greater than 100 pF; however for very small
capacitors, the total capacitance may be dominated by parasitic capacitance in the PCB layout. To determine the required External Oscillator Frequency Control value (XFCN) in the OSCXCN Register, first
select the RC network value to produce the desired frequency of oscillation, according to Equation 18.1,
where f = the frequency of oscillation in MHz, C = the capacitor value in pF, and R = the pull-up resistor
value in kΩ.
3
f = 1.23 × 10 ⁄ ( R × C )
Equation 18.1. RC Mode Oscillator Frequency
For example: If the frequency desired is 100 kHz, let R = 246 kΩ and C = 50 pF:
f = 1.23(103)/RC = 1.23(103)/[246 x 50] = 0.1 MHz = 100 kHz
Referring to the table in SFR Definition 18.6, the required XFCN setting is 010b.
18.4.3. External Capacitor Example
If a capacitor is used as an external oscillator for the MCU, the circuit should be configured as shown in
Figure 18.1, Option 3. The capacitor should be no greater than 100 pF; however for very small capacitors,
the total capacitance may be dominated by parasitic capacitance in the PCB layout. To determine the
required External Oscillator Frequency Control value (XFCN) in the OSCXCN Register, select the capacitor to be used and find the frequency of oscillation according to Equation , where f = the frequency of oscillation in MHz, C = the capacitor value in pF, and VDD = the MCU power supply in Volts.
167
Rev. 1.2
C8051F55x/56x/57x
f = ( KF ) ⁄ ( R × V DD )
Equation 18.2. C Mode Oscillator Frequency
For example: Assume VDD = 2.1 V and f = 75 kHz:
f = KF / (C x VDD)
0.075 MHz = KF / (C x 2.1)
Since the frequency of roughly 75 kHz is desired, select the K Factor from the table in SFR Definition 18.6
(OSCXCN) as KF = 7.7:
0.075 MHz = 7.7 / (C x 2.1)
C x 2.1 = 7.7 / 0.075 MHz
C = 102.6 / 2.0 pF = 51.3 pF
Therefore, the XFCN value to use in this example is 010b.
Rev. 1.2
168
C8051F55x/56x/57x
19. Port Input/Output
Digital and analog resources are available through 33 (C8051F568-9 and ‘F570-5), 25 (C8051F550-7) or
18 (C8051F550-7) I/O pins. Port pins P0.0-P4.0 on the C8051F568-9 and ‘F570-5, port pins P0.0-P3.0 on
theC8051F560-7, and port pins P0.0-P2.1 on the C8051F550-7 can be defined as general-purpose I/O
(GPIO), assigned to one of the internal digital resources, or assigned to an analog function as shown in
Figure 19.3. Port pin P4.0 on the C8051F568-9 and ‘F570-5 can be used as GPIO and is shared with the
C2 Interface Data signal (C2D). Similarly, port pin P3.0 is shared with C2D on the C8051F560-7 and port
pin P2.1 on the C8051F550-7. The designer has complete control over which functions are assigned, limited only by the number of physical I/O pins. This resource assignment flexibility is achieved through the
use of a Priority Crossbar Decoder. Note that the state of a Port I/O pin can always be read in the corresponding Port latch, regardless of the Crossbar settings.
The Crossbar assigns the selected internal digital resources to the I/O pins based on the Priority Decoder
(Figure 19.3 and Figure 19.4). The registers XBR0, XBR1, XBR2 are defined in SFR Definition 19.1 and
SFR Definition 19.2 and are used to select internal digital functions.
The Port I/O cells are configured as either push-pull or open-drain in the Port Output Mode registers
(PnMDOUT, where n = 0,1). Complete Electrical Specifications for Port I/O are given in Table 5.3 on
page 40.
XBR0, XBR1,
XBR2, PnSKIP
PnMDOUT,
PnDMIN Registers
External
Pins
Priority
Decoder
Highest
Priority
2
UART0
2
CAN0
4
(Internal Digital Signals)
SPI0
2
SMBus0
Digital
Crossbar
CP0
8
2
CP1
P0.0
P1
I/O
Cells
P1.0
Highest
Priority
P0.7
P1.7
P2
I/O
Cells
P2.0
P3
I/O
Cells
P3.0
P4
I/O
Cell
P4.0
P2.7
/SYSCLK
7
8
T0, T1,
/INT0,
/INT1
4
P0
P1
P2
P3
P4
P3.7
2
LIN0
8
33
Port
Latches
8
P0
I/O
Cells
2
PCA0
Lowest
Priority
8
Lowest
Priority
(Px.0-Px.7)
PnMASK
PnMATCH
Registers
Figure 19.1. Port I/O Functional Block Diagram
Rev. 1.2
169
C8051F55x/56x/57x
Note: When VIO rises faster than VDD, which can happen when VREGIN and VIO are tied together, a
delay created between GPIO power (VIO) and the logic controlling GPIO (VDD) results in a
temporary unknown state at the GPIO pins. When VIO rises faster than VDD, the GPIO may enter
the following states: floating, glitch low, or glitch high. Cross coupling VIO and VDD with a 4.7 µF
capacitor mitigates the root cause of the problem by allowing VIO and VDD to rise at the same rate.
19.1. Port I/O Modes of Operation
Port pins P0.0–P4.0 use the Port I/O cell shown in Figure 19.2. Each Port I/O cell can be configured by
software for analog I/O or digital I/O using the PnMDIN registers. On reset, all Port I/O cells default to a
high impedance state with weak pull-ups enabled until the Crossbar is enabled (XBARE = 1).
19.1.1. Port Pins Configured for Analog I/O
Any pins to be used as Comparator or ADC inputs, external oscillator inputs, or VREF should be configured for analog I/O (PnMDIN.n = 0). When a pin is configured for analog I/O, its weak pullup, digital driver,
and digital receiver are disabled. Port pins configured for analog I/O will always read back a value of 0.
Configuring pins as analog I/O saves power and isolates the Port pin from digital interference. Port pins
configured as digital inputs may still be used by analog peripherals; however, this practice is not recommended and may result in measurement errors.
19.1.2. Port Pins Configured For Digital I/O
Any pins to be used by digital peripherals (UART, SPI, SMBus, etc.), external digital event capture functions, or as GPIO should be configured as digital I/O (PnMDIN.n = 1). For digital I/O pins, one of two output
modes (push-pull or open-drain) must be selected using the PnMDOUT registers.
Push-pull outputs (PnMDOUT.n = 1) drive the Port pad to the VIO or GND supply rails based on the output
logic value of the Port pin. Open-drain outputs have the high side driver disabled; therefore, they only drive
the Port pad to GND when the output logic value is 0 and become high impedance inputs (both high low
drivers turned off) when the output logic value is 1.
WEAKPUD
(Weak Pull-Up Disable)
PxMDOUT.x
(1 for push-pull)
(0 for open-drain)
VIO
XBARE
(Crossbar
Enable)
(WEAK)
PORT
PAD
Px.x – Output
Logic Value
(Port Latch or
Crossbar)
PxMDIN.x
(1 for digital)
(0 for analog)
To/From Analog
Peripheral
GND
Px.x – Input Logic Value
(Reads 0 when pin is configured as an analog I/O)
Figure 19.2. Port I/O Cell Block Diagram
170
VIO
Rev. 1.2
C8051F55x/56x/57x
When a digital I/O cell is placed in the high impedance state, a weak pull-up transistor pulls the Port pad to
the VIO supply voltage to ensure the digital input is at a defined logic state. Weak pull-ups are disabled
when the I/O cell is driven to GND to minimize power consumption and may be globally disabled by setting
WEAKPUD to 1. The user should ensure that digital I/O are always internally or externally pulled or driven
to a valid logic state to minimize power consumption. Port pins configured for digital I/O always read back
the logic state of the Port pad, regardless of the output logic value of the Port pin.
19.1.3. Interfacing Port I/O in a Multi-Voltage System
All Port I/O are capable of interfacing to digital logic operating at a supply voltage higher than VDD and
less than 5.25 V. Connect the VIO pin to the voltage source of the interface logic.
19.2. Assigning Port I/O Pins to Analog and Digital Functions
Port I/O pins P0.0–P3.7 can be assigned to various analog, digital, and external interrupt functions. P4.0
can be assigned to only digital functions. The Port pins assigned to analog functions should be configured
for analog I/O, and Port pins assigned to digital or external interrupt functions should be configured for digital I/O.
19.2.1. Assigning Port I/O Pins to Analog Functions
Table 19.1 shows all available analog functions that require Port I/O assignments. Port pins selected for
these analog functions should have their corresponding bit in PnSKIP set to 1. This reserves the pin
for use by the analog function and does not allow it to be claimed by the Crossbar. Table 19.1 shows the
potential mapping of Port I/O to each analog function.
Table 19.1. Port I/O Assignment for Analog Functions
Analog Function
Potentially Assignable
Port Pins
SFR(s) used for
Assignment
P0.0–P3.71
ADC0MX, PnSKIP
ADC Input
1
Comparator0 or Compartor1 Input
P0.0–P2.7
CPT0MX, CPT1MX,
PnSKIP
Voltage Reference (VREF0)2
P0.0
REF0CN, PnSKIP
External Oscillator in Crystal Mode (XTAL1)
P0.2
OSCXCN, PnSKIP
External Oscillator in RC, C, or Crystal Mode (XTAL2)
P0.3
OSCXCN, PnSKIP
Notes:
1. P3.1–P3.7 are available on the 40-pin packages. P2.2-P3.0 are available 40-pin and 32-pin packages.
2. If VDD is selected as the voltage reference in the REF0CN register and the ADC is enabled in the ADC0CN
register, the P0.0/VREF pin cannot operate as a general purpose I/O pin in open-drain mode. With the above
settings, this pin can operate in push-pull output mode or as an analog input.
19.2.2. Assigning Port I/O Pins to Digital Functions
Any Port pins not assigned to analog functions may be assigned to digital functions or used as GPIO. Most
digital functions rely on the Crossbar for pin assignment; however, some digital functions bypass the
Crossbar in a manner similar to the analog functions listed above. Port pins used by these digital functions and any Port pins selected for use as GPIO should have their corresponding bit in PnSKIP set
to 1. Table 19.2 shows all available digital functions and the potential mapping of Port I/O to each digital
function.
Rev. 1.2
171
C8051F55x/56x/57x
Table 19.2. Port I/O Assignment for Digital Functions
Digital Function
UART0, SPI0, SMBus,
CAN0, LIN0, CP0, CP0A,
CP1, CP1A, SYSCLK, PCA0
(CEX0-5 and ECI), T0 or T1.
Potentially Assignable Port Pins
SFR(s) used for
Assignment
Any Port pin available for assignment by the
Crossbar. This includes P0.0–P4.0* pins which
have their PnSKIP bit set to 0.
Note: The Crossbar will always assign UART0
pins to P0.4 and P0.5 and always assign CAN0
to P0.6 and P0.7.
XBR0, XBR1, XBR2
P0.0–P4.0*
P0SKIP, P1SKIP,
P2SKIP, P3SKIP
Any pin used for GPIO
*Note: P3.1–P3.7 are available on the 40-pin packages. P2.2-P3.0 are available 40-pin and 32-pin packages.
19.2.3. Assigning Port I/O Pins to External Digital Event Capture Functions
External digital event capture functions can be used to trigger an interrupt or wake the device from a low
power mode when a transition occurs on a digital I/O pin. The digital event capture functions do not require
dedicated pins and will function on both GPIO pins (PnSKIP = 1) and pins in use by the Crossbar (PnSKIP
= 0). External digital event capture functions cannot be used on pins configured for analog I/O. Table 19.3
shows all available external digital event capture functions.
Table 19.3. Port I/O Assignment for External Digital Event Capture Functions
Digital Function
Potentially Assignable Port Pins
SFR(s) used for
Assignment
P1.0–P1.7
IT01CF
External Interrupt 0
External Interrupt 1
P1.0–P1.7
IT01CF
Port Match
P0.0–P3.7*
P0MASK, P0MAT
P1MASK, P1MAT
P2MASK, P2MAT
P3MASK, P3MAT
*Note: P3.1–P3.7 are available on the 40-pin packages. P2.2-P3.0 are available 40-pin and 32-pin packages
19.3. Priority Crossbar Decoder
The Priority Crossbar Decoder (Figure 19.3) assigns a priority to each I/O function, starting at the top with
UART0. When a digital resource is selected, the least-significant unassigned Port pin is assigned to that
resource excluding UART0, which is always assigned to pins P0.4 and P0.5, and excluding CAN0 which is
always assigned to pins P0.6 and P0.7. If a Port pin is assigned, the Crossbar skips that pin when assigning the next selected resource. Additionally, the Crossbar will skip Port pins whose associated bits in the
PnSKIP registers are set. The PnSKIP registers allow software to skip Port pins that are to be used for
analog input, dedicated functions, or GPIO.
Because of the nature of Priority Crossbar Decoder, not all peripherals can be located on all port pins.
Figure 19.3 maps peripherals to the potential port pins on which the peripheral I/O can appear.
Important Note on Crossbar Configuration: If a Port pin is claimed by a peripheral without use of the
Crossbar, its corresponding PnSKIP bit should be set. This applies to P0.0 if VREF is used, P0.1 if the
ADC is configured to use the external conversion start signal (CNVSTR), P0.3 and/or P0.2 if the external
oscillator circuit is enabled, and any selected ADC or Comparator inputs. The Crossbar skips selected pins
as if they were already assigned, and moves to the next unassigned pin.
172
Rev. 1.2
C8051F55x/56x/57x
XTAL2
1
2
3
4
5
6
7
0
1
2
3
4
/WR
XTAL1
0
P2
/RD
VREF
P IN I/O
CNVSTR
S p e cia l
F u n ctio n
S ig n a ls
P1
ALE
P0
P o rt
5
6
7
P3
P 2.2-P 2.7, P 3.0
available on 40-pin
and 32-pin pac k ages
0
1
2
3
4
5
6
7
0
P4
P 3.1-P 3.7, P 4.0
available on 40-pin
pac k ages
1
2
3
4
5
6
7
0
UA RT _T X
UA RT _R X
CA N_T X
CA N_R X
S CK
M IS O
MOSI
NS S
S DA
S CL
CP 0
CP 0A
CP 1
CP 1A
S YS CL K
CEX 0
CEX 1
CEX 2
CEX 3
CEX 4
CEX 5
ECI
T0
T1
L IN _T X
L IN _RX
Figure 19.3. Peripheral Availability on Port I/O Pins
Registers XBR0, XBR1, and XBR2 are used to assign the digital I/O resources to the physical I/O Port
pins. Note that when the SMBus is selected, the Crossbar assigns both pins associated with the SMBus
(SDA and SCL); and similarly when the UART, CAN or LIN are selected, the Crossbar assigns both pins
associated with the peripheral (TX and RX). UART0 pin assignments are fixed for bootloading purposes:
UART TX0 is always assigned to P0.4; UART RX0 is always assigned to P0.5. CAN0 pin assignments are
fixed to P0.6 for CAN_TX and P0.7 for CAN_RX. Standard Port I/Os appear contiguously after the prioritized functions have been assigned.
Important Note: The SPI can be operated in either 3-wire or 4-wire modes, pending the state of the NSSMD1–NSSMD0 bits in register SPI0CN. According to the SPI mode, the NSS signal may or may not be
routed to a Port pin.
As an example configuration, if CAN0, SPI0 in 4-wire mode, and PCA0 Modules 0, 1, and 2 are enabled on
the crossbar with P0.1, P0.2, and P0.5 skipped, the registers should be set as follows: XBR0 = 0x06
(CAN0 and SPI0 enabled), XBR1 = 0x0C (PCA0 modules 0, 1, and 2 enabled), XBR2 = 0x40 (Crossbar
enabled), and P0SKIP = 0x26 (P0.1, P0.2, and P0.5 skipped). The resulting crossbar would look as shown
in Figure 19.4.
Rev. 1.2
173
C8051F55x/56x/57x
P IN I/O
0
1
2
P1
3
P2
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
P4
P3
P 2 . 2 -P 2 . 7 , P 3 . 0
a va i l a b l e o n 4 0 -p i n
a n d 3 2 -p in p a c k a g e s
/WR
ALE
XTAL2
XTAL1
CNVSTR
VREF
S p e cia l
F u n c ti o n
S ig n a ls
P0
/RD
P o rt
5
6
7
P 3 . 1 -P 3 . 7 , P 4 . 0
a va i la b l e o n 4 0 - p i n
pac kages
0
1
0
0
2
3
4
5
6
7
0 0 0 0 0
P 3 S K I P [0 :7 ]
0
0
UART_TX
UART_RX
CAN_T X
CAN_RX
SCK
M IS O
MOSI
NSS
* N S S Is o n l y p i n n e d o u t i n 4 -w i re S P I M o d e
SDA
SCL
CP0
CP 0A
CP1
CP 1A
S YS CLK
CEX 0
CEX 1
CEX 2
CEX 3
CEX 4
CEX 5
ECI
T0
T1
L IN _T X
L IN _R X
0
1
1 0 0 1 0
P 0 S K I P [0 :7 ]
0
0
0
0 0 0 0 0
P 1 S K I P [0 :7 ]
0
0
0
0 0 0 0 0
P 2 S K I P [0 :7 ]
0
Figure 19.4. Crossbar Priority Decoder in Example Configuration
19.4. Port I/O Initialization
Port I/O initialization consists of the following steps:
1. Select the input mode (analog or digital) for all Port pins, using the Port Input Mode register (PnMDIN).
2. Select the output mode (open-drain or push-pull) for all Port pins, using the Port Output Mode register
(PnMDOUT).
3. Select any pins to be skipped by the I/O Crossbar using the Port Skip registers (PnSKIP).
4. Assign Port pins to desired peripherals.
5. Enable the Crossbar (XBARE = 1).
All Port pins must be configured as either analog or digital inputs. Port 4 C8051F568-9 and ‘F570-5 is a
digital-only Port. Any pins to be used as Comparator or ADC inputs should be configured as an analog
inputs. When a pin is configured as an analog input, its weak pullup, digital driver, and digital receiver are
disabled. This process saves power and reduces noise on the analog input. Pins configured as digital
inputs may still be used by analog peripherals; however this practice is not recommended.
Additionally, all analog input pins should be configured to be skipped by the Crossbar (accomplished by
setting the associated bits in PnSKIP). Port input mode is set in the PnMDIN register, where a 1 indicates a
digital input, and a 0 indicates an analog input. All pins default to digital inputs on reset. See SFR Definition
19.13 for the PnMDIN register details.
174
Rev. 1.2
C8051F55x/56x/57x
The output driver characteristics of the I/O pins are defined using the Port Output Mode registers (PnMDOUT). Each Port Output driver can be configured as either open drain or push-pull. This selection is
required even for the digital resources selected in the XBRn registers, and is not automatic. The only
exception to this is the SMBus (SDA, SCL) pins, which are configured as open-drain regardless of the
PnMDOUT settings. When the WEAKPUD bit in XBR2 is 0, a weak pullup is enabled for all Port I/O configured as open-drain. WEAKPUD does not affect the push-pull Port I/O. Furthermore, the weak pullup is
turned off on an output that is driving a 0 to avoid unnecessary power dissipation.
Registers XBR0, XBR1, and XBR2 must be loaded with the appropriate values to select the digital I/O
functions required by the design. Setting the XBARE bit in XBR2 to 1 enables the Crossbar. Until the
Crossbar is enabled, the external pins remain as standard Port I/O (in input mode), regardless of the XBRn
Register settings. For given XBRn Register settings, one can determine the I/O pin-out using the Priority
Decode Table; as an alternative, the Configuration Wizard utility of the Silicon Labs IDE software will determine the Port I/O pin-assignments based on the XBRn Register settings.
The Crossbar must be enabled to use Port pins as standard Port I/O in output mode. Port output drivers
are disabled while the Crossbar is disabled.
Rev. 1.2
175
C8051F55x/56x/57x
SFR Definition 19.1. XBR0: Port I/O Crossbar Register 0
Bit
7
6
5
4
3
2
1
0
Name
CP1AE
CP1E
CP0AE
CP0E
SMB0E
SPI0E
CAN0E
URT0E
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Address = 0xE1; SFR Page = 0x0F
Bit
Name
7
CP1AE
Function
Comparator1 Asynchronous Output Enable.
0: Asynchronous CP1 unavailable at Port pin.
1: Asynchronous CP1 routed to Port pin.
6
CP1E
Comparator1 Output Enable.
0: CP1 unavailable at Port pin.
1: CP1 routed to Port pin.
5
CP0AE
Comparator0 Asynchronous Output Enable.
0: Asynchronous CP0 unavailable at Port pin.
1: Asynchronous CP0 routed to Port pin.
4
CP0E
Comparator0 Output Enable.
0: CP0 unavailable at Port pin.
1: CP0 routed to Port pin.
3
SMB0E
SMBus I/O Enable.
0: SMBus I/O unavailable at Port pins.
1: SMBus I/O routed to Port pins.
2
SPI0E
SPI I/O Enable.
0: SPI I/O unavailable at Port pins.
1: SPI I/O routed to Port pins. Note that the SPI can be assigned either 3 or 4 GPIO
pins.
1
CAN0E
CAN I/O Output Enable.
0: CAN I/O unavailable at Port pins.
1: CAN_TX, CAN_RX routed to Port pins P0.6 and P0.7.
0
URT0E
UART I/O Output Enable.
0: UART I/O unavailable at Port pin.
1: UART TX0, RX0 routed to Port pins P0.4 and P0.5.
176
Rev. 1.2
C8051F55x/56x/57x
SFR Definition 19.2. XBR1: Port I/O Crossbar Register 1
Bit
7
6
5
4
Name
T1E
T0E
ECIE
Type
R/W
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
T1E
2
1
0
SYSCKE
Reserved
R
R/W
R/W
0
0
0
PCA0ME[2:0]
SFR Address = 0xE2; SFR Page = 0x0F
Bit
Name
7
3
Function
T1 Enable.
0: T1 unavailable at Port pin.
1: T1 routed to Port pin.
6
T0E
T0 Enable.
0: T0 unavailable at Port pin.
1: T0 routed to Port pin.
5
ECIE
PCA0 External Counter Input Enable.
0: ECI unavailable at Port pin.
1: ECI routed to Port pin.
4:2 PCA0ME[2:0] PCA Module I/O Enable Bits.
000: All PCA I/O unavailable at Port pins.
001: CEX0 routed to Port pin.
010: CEX0, CEX1 routed to Port pins.
011: CEX0, CEX1, CEX2 routed to Port pins.
100: CEX0, CEX1, CEX2, CEX3 routed to Port pins.
101: CEX0, CEX1, CEX2, CEX3, CEX4 routed to Port pins.
110: CEX0, CEX1, CEX2, CEX3, CEX4, CEX5 routed to Port pins.
111: RESERVED
1
SYSCKE
/SYSCLK Output Enable.
0: /SYSCLK unavailable at Port pin.
1: /SYSCLK output routed to Port pin.
0
Reserved
Always Write to 0.
Rev. 1.2
177
C8051F55x/56x/57x
SFR Definition 19.3. XBR2: Port I/O Crossbar Register 1
Bit
7
Name WEAKPUD
6
5
4
XBARE
3
2
1
Reserved
0
LIN0E
Type
R/W
R/W
R/W
R/W
R/W
R
R/W
R/W
Reset
0
0
0
0
0
0
0
0
SFR Address = 0xC7; SFR Page = 0x0F
Bit
Name
7
WEAKPUD
Function
Port I/O Weak Pullup Disable.
0: Weak Pullups enabled (except for Ports whose I/O are configured for analog
mode).
1: Weak Pullups disabled.
6
XBARE
Crossbar Enable.
0: Crossbar disabled.
1: Crossbar enabled.
5:1
Reserved
Always Write to 00000b.
0
LIN0E
LIN I/O Output Enable.
0: LIN I/O unavailable at Port pin.
1: LIN_TX, LIN_RX routed to Port pins.
178
Rev. 1.2
C8051F55x/56x/57x
19.5. Port Match
Port match functionality allows system events to be triggered by a logic value change on P0, P1, P2 or P3.
A software controlled value stored in the PnMATCH registers specifies the expected or normal logic values
of P0, P1, P2, and P3. A Port mismatch event occurs if the logic levels of the Port’s input pins no longer
match the software controlled value. This allows Software to be notified if a certain change or pattern
occurs on P0, P1, P2, or P3 input pins regardless of the XBRn settings.
The PnMASK registers can be used to individually select which of the port pins should be compared
against the PnMATCH registers. A Port mismatch event is generated if (Pn & PnMASK) does not equal
(PnMATCH & PnMASK), where n is 0, 1, 2 or 3
A Port mismatch event may be used to generate an interrupt or wake the device from a low power mode,
such as IDLE or SUSPEND. See the Interrupts and Power Options chapters for more details on interrupt
and wake-up sources.
SFR Definition 19.4. P0MASK: Port 0 Mask Register
Bit
7
6
5
4
3
Name
P0MASK[7:0]
Type
R/W
Reset
0
0
0
0
0
SFR Address = 0xF2; SFR Page = 0x00
Bit
Name
7:0
P0MASK[7:0]
2
1
0
0
0
0
Function
Port 0 Mask Value.
Selects P0 pins to be compared to the corresponding bits in P0MAT.
0: P0.n pin logic value is ignored and cannot cause a Port Mismatch event.
1: P0.n pin logic value is compared to P0MAT.n.
SFR Definition 19.5. P0MAT: Port 0 Match Register
Bit
7
6
5
4
3
Name
P0MAT[7:0]
Type
R/W
Reset
1
1
1
SFR Address = 0xF1; SFR Page = 0x00
Bit
Name
7:0
P0MAT[7:0]
1
1
2
1
0
1
1
1
Function
Port 0 Match Value.
Match comparison value used on Port 0 for bits in P0MAT which are set to 1.
0: P0.n pin logic value is compared with logic LOW.
1: P0.n pin logic value is compared with logic HIGH.
Rev. 1.2
179
C8051F55x/56x/57x
SFR Definition 19.6. P1MASK: Port 1 Mask Register
Bit
7
6
5
4
3
Name
P1MASK[7:0]
Type
R/W
Reset
0
0
0
0
0
SFR Address = 0xF4; SFR Page = 0x00
Bit
Name
7:0
P1MASK[7:0]
2
1
0
0
0
0
Function
Port 1 Mask Value.
Selects P1 pins to be compared to the corresponding bits in P1MAT.
0: P1.n pin logic value is ignored and cannot cause a Port Mismatch event.
1: P1.n pin logic value is compared to P1MAT.n.
SFR Definition 19.7. P1MAT: Port 1 Match Register
Bit
7
6
5
4
3
Name
P1MAT[7:0]
Type
R/W
Reset
1
1
1
1
SFR Address = 0xF3; SFR Page = 0x00
Bit
Name
7:0
P1MAT[7:0]
1
2
1
0
1
1
1
Function
Port 1 Match Value.
Match comparison value used on Port 1 for bits in P1MAT which are set to 1.
0: P1.n pin logic value is compared with logic LOW.
1: P1.n pin logic value is compared with logic HIGH.
180
Rev. 1.2
C8051F55x/56x/57x
SFR Definition 19.8. P2MASK: Port 2 Mask Register
Bit
7
6
5
4
3
Name
P2MASK[7:0]
Type
R/W
Reset
0
0
0
0
0
SFR Address = 0xB2; SFR Page = 0x00
Bit
Name
7:0
P2MASK[7:0]
2
1
0
0
0
0
Function
Port 2 Mask Value.
Selects P2 pins to be compared to the corresponding bits in P2MAT.
0: P2.n pin logic value is ignored and cannot cause a Port Mismatch event.
1: P2.n pin logic value is compared to P2MAT.n.
Note: P2.2–P2.7 are available on 40-pin and 32-pin packages.
SFR Definition 19.9. P2MAT: Port 2 Match Register
Bit
7
6
5
4
3
Name
P2MAT[7:0]
Type
R/W
Reset
1
1
1
1
1
SFR Address = 0xB1; SFR Page = 0x00
Bit
Name
7:0
P2MAT[7:0]
2
1
0
1
1
1
Function
Port 2 Match Value.
Match comparison value used on Port 2 for bits in P2MAT which are set to 1.
0: P2.n pin logic value is compared with logic LOW.
1: P2.n pin logic value is compared with logic HIGH.
Note: P2.2–P2.7 are available on 40-pin and 32-pin packages.
Rev. 1.2
181
C8051F55x/56x/57x
SFR Definition 19.10. P3MASK: Port 3 Mask Register
Bit
7
6
5
4
3
Name
P3MASK[7:0]
Type
R/W
Reset
0
0
0
0
0
SFR Address = 0xAF; SFR Page = 0x00
Bit
Name
7:0
P3MASK[7:0]
2
1
0
0
0
0
Function
Port 1 Mask Value.
Selects P3 pins to be compared to the corresponding bits in P3MAT.
0: P3.n pin logic value is ignored and cannot cause a Port Mismatch event.
1: P3.n pin logic value is compared to P3MAT.n.
Note: P3.0 is available on 40-pin and 32-pin packages. P3.1-P3.7 are available on 40-pin packages
SFR Definition 19.11. P3MAT: Port 3 Match Register
Bit
7
6
5
4
3
Name
P3MAT[7:0]
Type
R/W
Reset
1
1
1
1
SFR Address = 0xAE; SFR Page = 0x00
Bit
Name
7:0
P3MAT[7:0]
1
2
1
0
1
1
1
Function
Port 3 Match Value.
Match comparison value used on Port 3 for bits in P3MAT which are set to 1.
0: P3.n pin logic value is compared with logic LOW.
1: P3.n pin logic value is compared with logic HIGH.
Note: P3.0 is available on 40-pin and 32-pin packages. P3.1-P3.7 are available on 40-pin packages
182
Rev. 1.2
C8051F55x/56x/57x
19.6. Special Function Registers for Accessing and Configuring Port I/O
All Port I/O are accessed through corresponding special function registers (SFRs) that are both byte
addressable and bit addressable, except for P4 which is only byte addressable. When writing to a Port, the
value written to the SFR is latched to maintain the output data value at each pin. When reading, the logic
levels of the Port's input pins are returned regardless of the XBRn settings (i.e., even when the pin is
assigned to another signal by the Crossbar, the Port register can always read its corresponding Port I/O
pin). The exception to this is the execution of the read-modify-write instructions that target a Port Latch register as the destination. The read-modify-write instructions when operating on a Port SFR are the following:
ANL, ORL, XRL, JBC, CPL, INC, DEC, DJNZ and MOV, CLR or SETB, when the destination is an individual bit in a Port SFR. For these instructions, the value of the latch register (not the pin) is read, modified,
and written back to the SFR.
Ports 0–3 have a corresponding PnSKIP register which allows its individual Port pins to be assigned to digital functions or skipped by the Crossbar. All Port pins used for analog functions, GPIO, or dedicated digital
functions such as the EMIF should have their PnSKIP bit set to 1.
The Port input mode of the I/O pins is defined using the Port Input Mode registers (PnMDIN). Each Port
cell can be configured for analog or digital I/O. This selection is required even for the digital resources
selected in the XBRn registers, and is not automatic. The only exception to this is P4, which can only be
used for digital I/O.
The output driver characteristics of the I/O pins are defined using the Port Output Mode registers (PnMDOUT). Each Port Output driver can be configured as either open drain or push-pull. This selection is
required even for the digital resources selected in the XBRn registers, and is not automatic. The only
exception to this is the SMBus (SDA, SCL) pins, which are configured as open-drain regardless of the
PnMDOUT settings.
SFR Definition 19.12. P0: Port 0
Bit
7
6
5
4
Name
P0[7:0]
Type
R/W
Reset
1
1
1
1
3
2
1
0
1
1
1
1
SFR Address = 0x80; SFR Page = All Pages; Bit-Addressable
Bit
Name
Description
Write
7:0
P0[7:0]
Port 0 Data.
Sets the Port latch logic
value or reads the Port pin
logic state in Port cells configured for digital I/O.
0: Set output latch to logic
LOW.
1: Set output latch to logic
HIGH.
Rev. 1.2
Read
0: P0.n Port pin is logic
LOW.
1: P0.n Port pin is logic
HIGH.
183
C8051F55x/56x/57x
SFR Definition 19.13. P0MDIN: Port 0 Input Mode
Bit
7
6
5
4
3
Name
P0MDIN[7:0]
Type
R/W
Reset
1
1
1
1
1
SFR Address = 0xF1; SFR Page = 0x0F
Bit
Name
7:0
P0MDIN[7:0]
2
1
0
1
1
1
Function
Analog Configuration Bits for P0.7–P0.0 (respectively).
Port pins configured for analog mode have their weak pull-up and digital receiver
disabled. For analog mode, the pin also needs to be configured for open-drain
mode in the P0MDOUT register.
0: Corresponding P0.n pin is configured for analog mode.
1: Corresponding P0.n pin is not configured for analog mode.
SFR Definition 19.14. P0MDOUT: Port 0 Output Mode
Bit
7
6
5
4
3
Name
P0MDOUT[7:0]
Type
R/W
Reset
0
0
0
0
SFR Address = 0xA4; SFR Page = 0x0F
Bit
Name
0
2
1
0
0
0
0
Function
7:0 P0MDOUT[7:0] Output Configuration Bits for P0.7–P0.0 (respectively).
These bits are ignored if the corresponding bit in register P0MDIN is logic 0.
0: Corresponding P0.n Output is open-drain.
1: Corresponding P0.n Output is push-pull.
184
Rev. 1.2
C8051F55x/56x/57x
SFR Definition 19.15. P0SKIP: Port 0 Skip
Bit
7
6
5
4
3
Name
P0SKIP[7:0]
Type
R/W
Reset
0
0
0
0
0
SFR Address = 0xD4; SFR Page = 0x0F
Bit
Name
7:0
P0SKIP[7:0]
2
1
0
0
0
0
Function
Port 0 Crossbar Skip Enable Bits.
These bits select Port 0 pins to be skipped by the Crossbar Decoder. Port pins
used for analog, special functions or GPIO should be skipped by the Crossbar.
0: Corresponding P0.n pin is not skipped by the Crossbar.
1: Corresponding P0.n pin is skipped by the Crossbar.
SFR Definition 19.16. P1: Port 1
Bit
7
6
5
4
Name
P1[7:0]
Type
R/W
Reset
1
1
1
1
3
2
1
0
1
1
1
1
SFR Address = 0x90; SFR Page = All Pages; Bit-Addressable
Bit
Name
Description
Write
7:0
P1[7:0]
Port 1 Data.
Sets the Port latch logic
value or reads the Port pin
logic state in Port cells configured for digital I/O.
0: Set output latch to logic
LOW.
1: Set output latch to logic
HIGH.
Rev. 1.2
Read
0: P1.n Port pin is logic
LOW.
1: P1.n Port pin is logic
HIGH.
185
C8051F55x/56x/57x
SFR Definition 19.17. P1MDIN: Port 1 Input Mode
Bit
7
6
5
4
3
Name
P1MDIN[7:0]
Type
R/W
Reset
1
1
1
1
1
SFR Address = 0xF2; SFR Page = 0x0F
Bit
Name
7:0
P1MDIN[7:0]
2
1
0
1
1
1
Function
Analog Configuration Bits for P1.7–P1.0 (respectively).
Port pins configured for analog mode have their weak pull-up and digital receiver
disabled. For analog mode, the pin also needs to be configured for open-drain
mode in the P1MDOUT register.
0: Corresponding P1.n pin is configured for analog mode.
1: Corresponding P1.n pin is not configured for analog mode.
SFR Definition 19.18. P1MDOUT: Port 1 Output Mode
Bit
7
6
5
4
3
Name
P1MDOUT[7:0]
Type
R/W
Reset
0
0
0
0
SFR Address = 0xA5; SFR Page = 0x0F
Bit
Name
0
2
1
0
0
0
0
Function
7:0 P1MDOUT[7:0] Output Configuration Bits for P1.7–P1.0 (respectively).
These bits are ignored if the corresponding bit in register P1MDIN is logic 0.
0: Corresponding P1.n Output is open-drain.
1: Corresponding P1.n Output is push-pull.
186
Rev. 1.2
C8051F55x/56x/57x
SFR Definition 19.19. P1SKIP: Port 1 Skip
Bit
7
6
5
4
3
Name
P1SKIP[7:0]
Type
R/W
Reset
0
0
0
0
0
SFR Address = 0xD5; SFR Page = 0x0F
Bit
Name
7:0
P1SKIP[7:0]
2
1
0
0
0
0
Function
Port 1 Crossbar Skip Enable Bits.
These bits select Port 1 pins to be skipped by the Crossbar Decoder. Port pins
used for analog, special functions or GPIO should be skipped by the Crossbar.
0: Corresponding P1.n pin is not skipped by the Crossbar.
1: Corresponding P1.n pin is skipped by the Crossbar.
SFR Definition 19.20. P2: Port 2
Bit
7
6
5
4
Name
P2[7:0]
Type
R/W
Reset
1
1
1
1
3
2
1
0
1
1
1
1
SFR Address = 0xA0; SFR Page = All Pages; Bit-Addressable
Bit
Name
Description
Write
7:0
P2[7:0]
Port 2Data.
Sets the Port latch logic
value or reads the Port pin
logic state in Port cells configured for digital I/O.
0: Set output latch to logic
LOW.
1: Set output latch to logic
HIGH.
Read
0: P2.n Port pin is logic
LOW.
1: P2.n Port pin is logic
HIGH.
Note: P2.2-P2.7 are available on 40-pin and 32-pin packages.
Rev. 1.2
187
C8051F55x/56x/57x
SFR Definition 19.21. P2MDIN: Port 2 Input Mode
Bit
7
6
5
4
3
Name
P2MDIN[7:0]
Type
R/W
Reset
1
1
1
1
1
SFR Address = 0xF3; SFR Page = 0x0F
Bit
Name
7:0
P2MDIN[7:0]
2
1
0
1
1
1
Function
Analog Configuration Bits for P2.7–P2.0 (respectively).
Port pins configured for analog mode have their weak pull-up and digital receiver
disabled. For analog mode, the pin also needs to be configured for open-drain
mode in the P2MDOUT register.
0: Corresponding P2.n pin is configured for analog mode.
1: Corresponding P2.n pin is not configured for analog mode.
Note: P2.2-P2.7 are available on 40-pin and 32-pin packages.
SFR Definition 19.22. P2MDOUT: Port 2 Output Mode
Bit
7
6
5
4
3
Name
P2MDOUT[7:0]
Type
R/W
Reset
0
0
0
0
SFR Address = 0xA6; SFR Page = 0x0F
Bit
Name
0
2
1
0
0
0
0
Function
7:0 P2MDOUT[7:0] Output Configuration Bits for P2.7–P2.0 (respectively).
These bits are ignored if the corresponding bit in register P2MDIN is logic 0.
0: Corresponding P2.n Output is open-drain.
1: Corresponding P2.n Output is push-pull.
Note: P2.2-P2.7 are available on 40-pin and 32-pin packages.
188
Rev. 1.2
C8051F55x/56x/57x
SFR Definition 19.23. P2SKIP: Port 2 Skip
Bit
7
6
5
4
3
Name
P2SKIP[7:0]
Type
R/W
Reset
0
0
0
0
0
SFR Address = 0xD6; SFR Page = 0x0F
Bit
Name
7:0
P2SKIP[7:0]
2
1
0
0
0
0
Function
Port 2 Crossbar Skip Enable Bits.
These bits select Port 2 pins to be skipped by the Crossbar Decoder. Port pins
used for analog, special functions or GPIO should be skipped by the Crossbar.
0: Corresponding P2.n pin is not skipped by the Crossbar.
1: Corresponding P2.n pin is skipped by the Crossbar.
Note: P2.2-P2.7 are available on 40-pin and 32-pin packages.
SFR Definition 19.24. P3: Port 3
Bit
7
6
5
4
Name
P3[7:0]
Type
R/W
Reset
1
1
1
1
3
2
1
0
1
1
1
1
SFR Address = 0xB0; SFR Page = All Pages; Bit-Addressable
Bit
Name
Description
Write
7:0
P3[7:0]
Port 3 Data.
Sets the Port latch logic
value or reads the Port pin
logic state in Port cells configured for digital I/O.
0: Set output latch to logic
LOW.
1: Set output latch to logic
HIGH.
Read
0: P3.n Port pin is logic
LOW.
1: P3.n Port pin is logic
HIGH.
Note: P3.0 is available on 40-pin and 32-pin packages. P3.1-P3.7 are available on 40-pin packages
Rev. 1.2
189
C8051F55x/56x/57x
SFR Definition 19.25. P3MDIN: Port 3 Input Mode
Bit
7
6
5
4
3
Name
P3MDIN[7:0]
Type
R/W
Reset
1
1
1
1
1
SFR Address = 0xF4; SFR Page = 0x0F
Bit
Name
7:0
P3MDIN[7:0]
2
1
0
1
1
1
Function
Analog Configuration Bits for P3.7–P3.0 (respectively).
Port pins configured for analog mode have their weak pull-up and digital receiver
disabled. For analog mode, the pin also needs to be configured for open-drain
mode in the P3MDOUT register.
0: Corresponding P3.n pin is configured for analog mode.
1: Corresponding P3.n pin is not configured for analog mode.
Note: P3.0 is available on 40-pin and 32-pin packages. P3.1-P3.7 are available on 40-pin packages
SFR Definition 19.26. P3MDOUT: Port 3 Output Mode
Bit
7
6
5
4
3
Name
P3MDOUT[7:0]
Type
R/W
Reset
0
0
0
0
SFR Address = 0xAE; SFR Page = 0x0F
Bit
Name
0
2
1
0
0
0
0
Function
7:0 P3MDOUT[7:0] Output Configuration Bits for P3.7–P3.0 (respectively).
These bits are ignored if the corresponding bit in register P3MDIN is logic 0.
0: Corresponding P3.n Output is open-drain.
1: Corresponding P3.n Output is push-pull.
Note: P3.0 is available on 40-pin and 32-pin packages. P3.1-P3.7 are available on 40-pin packages
190
Rev. 1.2
C8051F55x/56x/57x
SFR Definition 19.27. P3SKIP: Port 3Skip
Bit
7
6
5
4
3
Name
P3SKIP[7:0]
Type
R/W
Reset
0
0
0
0
0
SFR Address = 0xD7; SFR Page = 0x0F
Bit
Name
7:0
P3SKIP[7:0]
2
1
0
0
0
0
Function
Port 3 Crossbar Skip Enable Bits.
These bits select Port 3 pins to be skipped by the Crossbar Decoder. Port pins
used for analog, special functions or GPIO should be skipped by the Crossbar.
0: Corresponding P3.n pin is not skipped by the Crossbar.
1: Corresponding P3.n pin is skipped by the Crossbar.
Note: P3.0 is available on 40-pin and 32-pin packages. P3.1-P3.7 are available on 40-pin packages
SFR Definition 19.28. P4: Port 4
Bit
7
6
5
4
Name
P4[7:0]
Type
R/W
Reset
1
1
1
SFR Address = 0xB5; SFR Page = All Pages
Bit
Name
Description
7:0
P4[7:0]
Port 4 Data.
Sets the Port latch logic
value or reads the Port pin
logic state in Port cells configured for digital I/O.
1
3
2
1
0
1
1
1
1
Write
0: Set output latch to logic
LOW.
1: Set output latch to logic
HIGH.
Read
0: P4.n Port pin is logic
LOW.
1: P4.n Port pin is logic
HIGH.
Note: Port 4.0 is available on 40-pin packages.
Rev. 1.2
191
C8051F55x/56x/57x
SFR Definition 19.29. P4MDOUT: Port 4 Output Mode
Bit
7
6
5
4
3
Name
P4MDOUT[7:0]
Type
R/W
Reset
0
0
0
0
SFR Address = 0xAF; SFR Page = 0x0F
Bit
Name
0
2
1
0
0
0
0
Function
7:0 P4MDOUT[7:0] Output Configuration Bits for P4.7–P4.0 (respectively).
0: Corresponding P4.n Output is open-drain.
1: Corresponding P4.n Output is push-pull.
Note: Port 4.0 is available on 40-pin packages.
192
Rev. 1.2
C8051F55x/56x/57x
20. Local Interconnect Network (LIN0)
Important Note: This chapter assumes an understanding of the Local Interconnect Network (LIN) protocol. For more information about the LIN protocol, including specifications, please refer to the LIN consortium (http://www.lin-subbus.org).
LIN is an asynchronous, serial communications interface used primarily in automotive networks. The Silicon Laboratories LIN controller is compliant to the 2.1 Specification, implements a complete hardware LIN
interface and includes the following features:
Selectable Master and Slave modes.
Automatic baud rate option in slave mode.
The internal oscillator is accurate to within 0.5% of 24 MHz across the entire temperature range and for
VDD voltages greater than or equal to the minimum output of the on-chip voltage regulator, so an
external oscillator is not necessary for master mode operation for most systems.
Note: The minimum system clock (SYSCLK) required when using the LIN controller is 8 MHz.
LIN Controller
LIN Data
Registers
8051 MCU Core
LIN Control
Registers
LIN0ADR
LIN0DAT
Indirectly Addressed Registers
TX
Control State Machine
LIN0CF
RX
Figure 20.1. LIN Block Diagram
The LIN controller has four main components:
LIN Access Registers—Provide the interface between the MCU core and the LIN controller.
LIN Data Registers—Where transmitted and received message data bytes are stored.
LIN Control Registers—Control the functionality of the LIN interface.
Control State Machine and Bit Streaming Logic—Contains the hardware that serializes messages and
controls the bus timing of the controller.
Rev. 1.2
193
C8051F55x/56x/57x
20.1. Software Interface with the LIN Controller
The selection of the mode (Master or Slave) and the automatic baud rate feature are done though the LIN0
Control Mode (LIN0CF) register. The other LIN registers are accessed indirectly through the two SFRs
LIN0 Address (LIN0ADR) and LIN0 Data (LIN0DAT). The LIN0ADR register selects which LIN register is
targeted by reads/writes of the LIN0DAT register. The full list of indirectly-accessible LIN registers is given
in Table 20.4 on page 202.
20.2. LIN Interface Setup and Operation
The hardware based LIN controller allows for the implementation of both Master and Slave nodes with
minimal firmware overhead and complete control of the interface status while allowing for interrupt and
polled mode operation.
The first step to use the controller is to define the basic characteristics of the node:
Mode—Master or Slave
Baud Rate—Either defined manually or using the autobaud feature (slave mode only)
Checksum Type—Select between classic or enhanced checksum, both of which are implemented in hardware.
20.2.1. Mode Definition
Following the LIN specification, the controller implements in hardware both the Slave and Master operating
modes. The mode is configured using the MODE bit (LIN0CF.6).
20.2.2. Baud Rate Options: Manual or Autobaud
The LIN controller can be selected to have its baud rate calculated manually or automatically. A master
node must always have its baud rate set manually, but slave nodes can choose between a manual or automatic setup. The configuration is selected using the ABAUD bit (LIN0CF.5).
Both the manual and automatic baud rate configurations require additional setup. The following sections
explain the different options available and their relation with the baud rate, along with the steps necessary
to achieve the required baud rate.
20.2.3. Baud Rate Calculations: Manual Mode
The baud rate used by the LIN controller is a function of the System Clock (SYSCLK) and the LIN timing
registers according to the following equation:
SYSCLK
baud_rate = --------------------------------------------------------------------------------------------------------------------( prescaler + 1 )
× divider × ( multiplier + 1 )
2
The prescaler, divider and multiplier factors are part of the LIN0DIV and LIN0MUL registers and can
assume values in the following range:
Table 20.1. Baud Rate Calculation Variable Ranges
Factor
Range
prescaler
0…3
multiplier
0…31
divider
200…511
Important Note: The minimum system clock (SYSCLK) to operate the LIN controller is 8 MHz.
Use the following equations to calculate the values for the variables for the baud-rate equation:
194
Rev. 1.2
C8051F55x/56x/57x
20000
multiplier = ----------------------------- – 1
baud_rate
SYSCLK
prescaler = ln -----------------------------------------------------------------------------------------------( multiplier + 1 ) × baud_rate × 200
1
-–1
× ------ln2
SYSCLK
divider = -------------------------------------------------------------------------------------------------------------------------------------( prescaler + 1 )
(2
× ( multiplier + 1 ) × baud_rate )
In all of these equations, the results must be rounded down to the nearest integer.
The following example shows the steps for calculating the baud rate values for a Master node running at
24 MHz and communicating at 19200 bits/sec. First, calculate the multiplier:
20000
multiplier = ---------------- – 1 = 0.0417
19200
≅0
Next, calculate the prescaler:
24000000
prescaler = ln ----------------------------------------------------------( 0 + 1 ) × 19200 × 200
1
- – 1 = 1.644 ≅ 1
× ------ln2
Finally, calculate the divider:
24000000
divider = ----------------------------------------------------------------------- = 312.5 ≅ 312
(1 + 1)
× ( 0 + 1 ) × 19200
2
These values lead to the following baud rate:
24000000
baud_rate = ---------------------------------------------------------------(1 + 1)
× ( 0 + 1 ) × 312
2
≅ 19230.77
The following code programs the interface in Master mode, using the Enhanced Checksum and enables
the interface to operate at 19230 bits/sec using a 24 MHz system clock.
LIN0CF
LIN0CF
= 0x80;
|= 0x40;
// Activate the interface
// Set the node as a Master
LIN0ADR = 0x0D;
// Point to the LIN0MUL register
// Initialize the register (prescaler, multiplier and bit 8 of divider)
LIN0DAT = ( 0x01 8 );
LIN0ADR
= 0x0C;
// Point to the LIN0DIV register
LIN0DAT
= (unsigned char)_0x138;
// Initialize LIN0DIV
LIN0ADR
LIN0DAT
= 0x0B;
|= 0x80;
LIN0ADR
LIN0DAT
= 0x08;
= 0x0C;
// Point to the LIN0SIZE register
// Initialize the checksum as Enhanced
// Point to LIN0CTRL register
// Reset any error and the interrupt
Table 20.2 includes the configuration values required for the typical system clocks and baud rates:
Rev. 1.2
195
C8051F55x/56x/57x
Table 20.2. Manual Baud Rate Parameters Examples
Baud (bits/sec)
1
325
1
1
325
3
1
325
19
1
312
24.5
0
1
306
0
1
319
1
1
319
3
1
319
19
1
306
Div.
Pres.
0
Mult.
Mult.
312
Div.
Pres.
1
Div.
Mult.
0
Div.
25
Div.
Pres.
1K
Mult.
4.8 K
Pres.
9.6 K
Mult.
SYSCLK
(MHz)
19.2 K
Pres.
20 K
24
0
1
300
0
1
312
1
1
312
3
1
312
19
1
300
22.1184
0
1
276
0
1
288
1
1
288
3
1
288
19
1
276
16
0
1
200
0
1
208
1
1
208
3
1
208
19
1
200
12.25
0
0
306
0
0
319
1
0
319
3
0
319
19
0
306
12
0
0
300
0
0
312
1
0
312
3
0
312
19
0
300
11.0592
0
0
276
0
0
288
1
0
288
3
0
288
19
0
276
8
0
0
200
0
0
208
1
0
208
3
0
208
19
0
200
20.2.4. Baud Rate Calculations—Automatic Mode
If the LIN controller is configured for slave mode, only the prescaler and divider need to be calculated:
SYSCLK
prescaler = ln ------------------------4000000
1
-–1
× ------ln2
SYSCLK
divider = ---------------------------------------------------------------------( prescaler + 1 )
× 20000
2
The following example calculates the values of these variables for a 24 MHz system clock:
24000000
prescaler = ln -------------------------4000000
1
- – 1 = 1.585 ≅ 1
× ------ln2
24000000
divider = --------------------------------------------- = 300
(1 + 1)
× 20000
2
Table 20.3 presents some typical values of system clock and baud rate along with their factors.
196
Rev. 1.2
C8051F55x/56x/57x
Table 20.3. Autobaud Parameters Examples
System Clock (MHz)
Prescaler
Divider
25
1
312
24.5
1
306
24
1
300
22.1184
1
276
16
1
200
12.25
0
306
12
0
300
11.0592
0
276
8
0
200
20.3. LIN Master Mode Operation
The master node is responsible for the scheduling of messages and sends the header of each frame containing the SYNCH BREAK FIELD, SYNCH FIELD, and IDENTIFIER FIELD. The steps to schedule a message transmission or reception are listed below.
1. Load the 6-bit Identifier into the LIN0ID register.
2. Load the data length into the LIN0SIZE register. Set the value to the number of data bytes or "1111b" if
the data length should be decoded from the identifier. Also, set the checksum type, classic or
enhanced, in the same LIN0SIZE register.
3. Set the data direction by setting the TXRX bit (LIN0CTRL.5). Set the bit to 1 to perform a master
transmit operation, or set the bit to 0 to perform a master receive operation.
4. If performing a master transmit operation, load the data bytes to transmit into the data buffer (LIN0DT1
to LIN0DT8).
5. Set the STREQ bit (LIN0CTRL.0) to start the message transfer. The LIN controller will schedule the
message frame and request an interrupt if the message transfer is successfully completed or if an error
has occurred.
This code segment shows the procedure to schedule a message in a transmission operation:
LIN0ADR
LIN0DAT
LIN0ADR
LIN0DAT
LIN0ADR
LIN0DAT
= 0x08;
|= 0x20;
= 0x0E;
= 0x11;
= 0x0B;
= ( LIN0DAT & 0xF0 ) |
LIN0ADR = 0x00;
for (i=0; i