cPCI-A-3U-200C Series
200W 3Ux8HP AC/DC CompactPCI™
SELECTION GUIDE
Output Current1
Model Number
CPCI-A-3U-200C
Power
200W
5V
3.3V
12V
-12V
25A
36A
5A
0.5A
For full details go to
www.murata-ps.com/rohs
Yes
Yes
INPUT CHARACTERISTICS
Parameter
Conditions
Input Operating Voltage
Auto range, single phase
DUCT
O
R
P
ETE
Input Frequency
FEATURES
3Ux8HP package
Input Current
230Vac
Power Factor
230Vac and 115Vac, full load
Inrush Current
230Vac
L
O
S
B
O
Min
Typ
Max
Units
90
264
Vac
47
63
Hz
3.5
Arms
50
Apk
0.98
OUTPUT CHARACTERISTICS
200W power at -5 to 55ºC
Output
Nominal Voltage
PICMG 2.11 Compliant
V11
+5.0Vdc
1
Output Current
Min
Max
0A
25A
Load Regulation1
±1%
Widerange 90-264VAC Input
V2
+3.3Vdc
0A
36A
±1%
Active power factor correction to EN61000-3-2
V31
+12Vdc
0A
5A
±4%
V41
-12Vdc
0A
0.5A
Parameter
Conditions
Min
Typ
Class B conducted EMI performance
±4%
Max
Units
47-pin I/O Connector
Line Regulation
All outputs
80% efficiency
PARD (V1 & V2)4
20MHz bandwidth
75
mVp-p
Full power with just 250lfm airflow
PARD (V3 & V4)4
20MHz bandwidth
120
mVp-p
Hot-swap capable
Hold-up Time
220Vac, full load
DESCRIPTION
Rise Time
The cPCI-A-3U-200C is a high-reliability, 200W, continuous power, 3Ux8HP CompactPCI™ power supply developed for chassis’ with airflows as low as 250lfm. The use
of 2 converters operating in parallel for the 3.3V and the
5V outputs enables maximum current draw on the two
outputs simultaneously. Compliant with the PICMG 2.11
standard.
With a widerange input of 90-264VAC, safety agency
approvals to UL60950 and EN60950, EMI compliance
to Class B FCC and EN55022 standards, the cPCI-A3U-300C was designed with globally-deployed systems
in mind. Additional features include remote sense compensation, unit enable control (EN#), output inhibit control
(INH#), output fault signal (FAL#), and thermal warning
signal (DEG#). LEDs are provided for visual indication of
input power presence and output fault condition.
0.5
14
Turn-on Delay
Transient Response
10% to 90% of full value
Settling time
V1, V2, & V3: Latching
Remote Sense Compensation2
V1, V2
Current Share Tolerance3
V1, V2
Pri-Sec
Isolation
Notes:
msec
2
sec
±5
%Vnom
30
ΔV, 50% load step
Over-Voltage and Short Circuit
Protection5
%
110
msec
500
μsec
130
%Vnom
200
mV
±10
%
3
kVac
Pri-Chassis
1.5
kVac
Sec-Chassis
100
Vdc
1. Maximum combined power any combination of outputs is 200W
2. Maximum voltage compensation for cable losses .
3. Tolerance applicable up to 6 parallel units. Single wire current share on V1 & V2 for 50% to 100% load.
4. Measured across 1μF ceramic capacitor and 120μF electrolytic capacitor.
5. Automatic recovery upon removal of overload condition.
www.murata-ps.com
cPCI-A-3U-200C.A01 Page 1 of 4
cPCI-A-3U-200C Series
200W 3Ux8HP AC/DC CompactPCI™
GENERAL CHARACTERISTICS
Parameter
Conditions
Efficiency
Min
Typ
230Vac, full load
80
120Vac, full load
76
Switching Frequency
Main Converter
MTBF
Calculated per Bellcore standard B332 Gb 30ºC
Weight
Unpackaged
Max
Units
%
68
kHz
300
khrs
800
g
PROTECTION
Parameter
Inception
Conditions/Response
Min
Typ
Max
Units
Inrush Current Limit
230VAC
50
Arms
Input Protection
Internal line fuse
6.3
Arms
130
%Vnom
Over-voltage Protection
V1, V2, & V3 with latched shutdown
Parameter
Conditions/Response
110
Output Overload Protection
Outputs are individually protected against overloads and indefinite short circuit with automatic recovery upon removal of the fault condition.
Hot-Swap Capability
Protected by internal ORing diodes
Output Fault Isolation
Output isolation devices are present in all outputs to isolate faults within a failed power supply.
Thermal Shutdown
Automatic recovery upon restoration to operational temperatures
STATUS & CONTROL SIGNALS & INDICATORS
Name
Description
Enable (EN#)
Contact closure to external ground to start unit. On shortest pin (last make, first break).
Output Inhibit (INH#)
TTL –compatible signal inhibited with GND or TTL “0”.
T
C
U
D
PRO
Output Fault (FAL#)
TTL compatible signal ,open collector active low signal .Indicates one or more outputs below 90% of specified rate.
Remote Sense (RS+, RS-)
Available on V1 & V2. Maximum voltage compensation for cable losses 200mV.
Thermal Warning (DEG#)
Open collector active low 10ºC before power supply shut down.
E
T
E
L
BSO
A single bi-color indicator LED
Front Panel Power Indicator LED
O
Green LED - indicates output in range
Red LED - indicates one or more outputs below 90% of specified range.
ENVIRONMENTAL CHARACTERISTICS
Parameter
Conditions
Ambient Operating Temperature
Full load with 250LFM forced air and derating linearly above 55°C to 70°C, by 2.5% per °C
Ambient Storage Temperature
Operating Humidity
Storage Humidity
Altitude
Non-condensing
Non-condensing
Min
Typ
Max
Units
-5
55
ºC
-40
85
ºC
95
%
95
%
Operating
6000
ft
Storage
40000
ft
www.murata-ps.com
cPCI-A-3U-200C.A01 Page 2 of 4
cPCI-A-3U-200C Series
200W 3Ux8HP AC/DC CompactPCI™
ELECTROMAGNETIC COMPATIBILITY (EMC)
Characteristic
Compliance
Input Current Harmonics
EN61000-3-2
Conducted Emissions
EN55022/CISPR22, Class B, with external TBD line filter
Electrostatic Discharge (ESD)
EN61000-4-2, Level 4, 8kV air
Radiated Immunity
EN61000-4-3, Level 3, 10V/m
T
C
U
D
PRO
Conducted Immunity
EN61000-4-4, Level 3, ±2kV
Line Voltage Surge
EN61000-4-5, Level 3, line-to-line 1kV line to chassis 2kV
Conducted Disturbance
EN61000-4-6, Level 2, 3Vrms
E
T
E
L
BSO
Power Frequency Magnetic Field
Line Voltage Interruptions
CERTIFICATIONS
EN61000-4-8, 3A/m
O
EN61000-4-11
Agency/Characteristic PENDING
Standard
UL
UL60950-1
CSA
CSA C22.2-234, Level 3 (per cUL)
CE
EN-60950, Class 1, SELV CE-Mark
RoHS
EN Directive 2002/95/EC; self-certified
SAFETY AGENCY RATINGS
Input Voltage
100-240Vac
Input Current
3.5A
MECHANICAL DIMENSIONS
6.43
1.60
2.50
169.60
40.34
3.10
17.63
POWER
FORCED COOLING AIR
94.00
CL
100.00
128.60
Overall size: 169.6mm D x 128.6mm H x 40.3mm W (6.68” D x 5.06” H x 1.59” W)
www.murata-ps.com
cPCI-A-3U-200C.A01 Page 3 of 4
cPCI-A-3U-200C Series
200W 3Ux8HP AC/DC CompactPCI™
CONNECTOR
RoHS COMPLIANCE INFORMATION
This series is compatible with RoHS soldering
systems with a peak wave solder temperature
of 300ºC for 10 seconds. The pin termination
finish on this product series is Tin Plate, Hot
Dipped over Matte Tin with Nickel Preplate.
The series is backward compatible with Sn/Pb
soldering systems.
For further information, please visit www.murata-ps.com/rohs
Pin
Pin Type
Signal Name
1-4
Normal
V1
V1 Output
5-12
Normal
RTN
V1 and V2 Return
13-18
Normal
V2
V2 Output
19
Normal
RTN
V3 Return
20
Normal
V3
V3 Output
21
Normal
V4
V4 Output
22
Normal
RTN
Signal Return
23
Normal
RTN
Signal Return
24
Normal
RTN
V4 Return
25
Normal
GA-0
Geographic ADD-0 (option)
26
Normal
Reverse
27
Short
EN#
28
Normal
GA-1
Geographic ADD-1 (option)
29
Normal
NC
Not Connected
30
Normal
V1 Sense
V1 Remote Sense
31
Normal
GA-2
Geographic ADD-2 (option)
32
Normal
NC
Not Connected
33
Normal
V2 Sense
V2 Remote Sense
34
Normal
S RTN
Sense Return
35
Normal
V1 Share
V1 Current Share
36
Normal
NC
Not Connected
37
Normal
IPMB_SCL
System Manager Bus (option)
38
Normal
DEG#
Degrade Signal
39
Normal
INH#
Open – ON Low - OFF
40
Normal
IPMB_SDA
System Manager Bus (option)
41
Normal
V2 Share
V2 Current Share
42
Normal
FAL#
Fail Signal
43
Normal
IPMB_PWR
System Manager (option) – Power
44
Normal
NC
Not Connected
45
Long
Chassis GND
Chassis GND
46
Long
AC Neutral
AC input Neutral
47
Long
AC Line
AC Input Line
E
T
E
L
BSO
T
C
U
D
PRO
O
Reverse
Enable
ISO9001
CERTIFIED
Murata Power Solutions, Inc.
11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A.
Tel: (508) 339-3000 (800) 233-2765 Fax: (508) 339-6356
www.murata-ps.com email: sales@murata-ps.com ISO 9001 REGISTERED
10/24/08
Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other
technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply
the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without
notice.
© 2008 Murata Power Solutions, Inc.
USA:
Mansfield (MA), Tel: (508) 339-3000, email: sales@murata-ps.com
Canada:
Toronto, Tel: (866) 740-1232, email: toronto@murata-ps.com
UK:
Milton Keynes, Tel: +44 (0)1908 615232, email: mk@murata-ps.com
France:
Montigny Le Bretonneux, Tel: +33 (0)1 34 60 01 01, email: france@murata-ps.com
Germany:
München, Tel: +49 (0)89-544334-0, email: munich@murata-ps.com
Japan:
Tokyo, Tel: 3-3779-1031, email: sales_tokyo@murata-ps.com
Osaka, Tel: 6-6354-2025, email: sales_osaka@murata-ps.com
China:
Shanghai, Tel: +86 215 027 3678, email: shanghai@murata-ps.com
Guangzhou, Tel: +86 208 221 8066, email: guangzhou@murata-ps.com
Singapore:
Parkway Centre, Tel: +65 6348 9096, email: singapore@murata-ps.com
www.murata-ps.com
cPCI-A-3U-200C.A01 Page 4 of 4
