Reference Specification
Type KJ
Safety Standard Certified Lead Type Disc Ceramic Capacitors for Automotive
Product specifications in this catalog are as of Aug. 2022, and are subject to change or
obsolescence without notice.
Please consult the approval sheet before ordering.Please read rating and Cautions first.
Reference only
CAUTION
1. OPERATING VOLTAGE
1) Do not apply a voltage to a safety standard certified product that exceeds the rated voltage as called
out in the specifications. Applied voltage between the terminals of a safety standard certified product
shall be less than or equal to the rated voltage (+ 10%). When a safety standard certified product is
used as a DC voltage product, the AC rated voltage value becomes the DC rated voltage value.
(Example:AC250V (r.m.s.) rated product can be used as DC250V (+ 10%) rated product.)
If both AC rated voltage and DC rated voltage are specified, apply the voltage lower than the
respective rated voltage.
1-1) When a safety standard certified product is used in a circuit connected to a commercial power
supply, ensure that the applied commercial power supply voltage including fluctuation should be less
than 10% above its rated voltage.
1-2) When using a safety standard certified product as a DC rated product in circuits other than those
connected to a commercial power supply.
When AC voltage is superimposed on DC voltage, the zero-to-peak voltage shall not exceed the rated
DC voltage. When AC voltage or pulse voltage is applied, the peak-to-peak voltage shall not exceed
the rated DC voltage.
Typical Voltage Applied to the DC Capacitor
DC Voltage
E
DC Voltage+AC
AC Voltage
E
E
Pulse Voltage
0
E
0
0
0
(E: Maximum possible applied voltage.)
2) Abnormal voltages (surge voltage, static electricity, pulse voltage, etc.) shall not exceed the rated DC
voltage.
2. OPERATING TEMPERATURE AND SELF-GENERATED HEAT
Keep the surface temperature of a capacitor below the upper limit of its rated operating temperature
range. Be sure to take into account the heat generated by the capacitor itself.
When the capacitor is used in a high-frequency current, pulse current or the like, it may have the
self-generated heat due to dielectric-loss. Applied voltage should be the load such as self-generated
heat is within 20 ℃ on the condition of atmosphere temperature 25 ℃. When measuring, use a
thermocouple of small thermal capacity-K of φ0.1mm and be in the condition where capacitor is not
affected by radiant heat of other components and wind of surroundings. Excessive heat may lead to
deterioration of the capacitor’s characteristics and reliability. (Never attempt to perform measurement
with the cooling fan running. Otherwise, accurate measurement cannot be ensured.)
3. TEST CONDITION FOR WITHSTANDING VOLTAGE
1) TEST EQUIPMENT
Test equipment for AC withstanding voltage should be used with the performance of the wave similar to
50/60 Hz sine wave.
If the distorted sine wave or over load exceeding the specified voltage value is applied, the defective
may be caused.
2) VOLTAGE APPLIED METHOD
When the withstanding voltage is applied, capacitor’s lead or terminal should be firmly connected to the
out-put of the withstanding voltage test equipment, and then the voltage should be raised from near
zero to the test voltage.
If the test voltage without the raise from near zero voltage would be applied directly to capacitor, test
voltage should be applied with the *zero cross. At the end of the test time, the test voltage should be
reduced to near zero, and then capacitor’s lead or terminal should be taken off the out-put of the
withstanding voltage test equipment.
If the test voltage without the raise from near zero voltage would
voltage sine wave
be applied directly to capacitor, the surge voltage may arise,
and therefore, the defective may be caused.
0V
*ZERO CROSS is the point where voltage sine wave pass 0V.
zero cross
- See the right figure -
EGD28A
1 / 20
Reference only
4. FAIL-SAFE
When capacitor would be broken, failure may result in a short circuit. Be sure to provide an
appropriate fail-safe function like a fuse on your product if failure would follow an electric shock,
fire or fume.
5. VIBRATION AND IMPACT
Do not expose a capacitor or its leads to excessive shock or vibration during use. Excessive shock or
vibration may cause to fatigue destruction of lead wires mounted on the circuit board. Please take
measures to hold a capacitor on the circuit boards by adhesive, molding resin or coating and other.
Please confirm there is no influence of holding measures on the product with an intended equipment.
6. SOLDERING
When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification of
the capacitor. Subjecting this product to excessive heating could melt the internal junction solder and
may result in thermal shocks that can crack the ceramic element.
When soldering capacitor with a soldering iron, it should be performed in following conditions.
Temperature of iron-tip : 400 °C max.
Soldering iron wattage : 50W max.
Soldering time
: 3.5s max.
7. BONDING, RESIN MOLDING AND COATING
In case of bonding, molding or coating this product, verify that these processes do not affect the
quality of capacitor by testing the performance of the bonded, molded or coated product in the
intended equipment.
In case of the amount of applications, dryness / hardening conditions of adhesives and molding
resins containing organic solvents (ethyl acetate, methyl ethyl ketone, toluene, etc.) are unsuitable,
the outer coating resin of a capacitor is damaged by the organic solvents and it may result, worst
case, in a short circuit.
The variation in thickness of adhesive, molding resin or coating may cause an outer coating resin
cracking and/or ceramic element cracking of a capacitor in a temperature cycling.
8. TREATMENT AFTER BONDING, RESIN MOLDING AND COATING
When the outer coating is hot (over 100 ℃) after soldering, it becomes soft and fragile.
So please be careful not to give it mechanical stress.
Failure to follow the above cautions may result, worst case, in a short circuit and cause fuming or
partial dispersion when the product is used.
9. OPERATING AND STORAGE ENVIRONMENT
The insulating coating of capacitors does not form a perfect seal; therefore, do not use or store
capacitors in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or
the like is present. And avoid exposure to moisture. Before cleaning, bonding, or molding
this product, verify that these processes do not affect product quality by testing the performance of a
cleaned, bonded or molded product in the intended equipment. Store the capacitors where the
temperature and relative humidity do not exceed -10 to 40 °C and 15 to 85%.
Use capacitors within 6 months after delivered. Check the solderability after 6 months or more.
EGD28A
2 / 20
Reference only
10. LIMITATION OF APPLICATIONS
Please contact us before using our products for the applications listed below which require especially
high reliability for the prevention of defects which might directly cause damage to the third party’s life,
body or property.
1. Aircraft equipment
2. Aerospace equipment
3. Undersea equipment
4. Power plant control equipment
5. Medical equipment
6. Transportation equipment (vehicles, trains, ships, etc.)
7. Traffic signal equipment
8. Disaster prevention / crime prevention equipment
9. Data-processing equipment exerting influence on public
10. Application of similar complexity and/or reliability requirements to the applications listed
in the above.
NOTICE
1. CLEANING (ULTRASONIC CLEANING)
To perform ultrasonic cleaning, observe the following conditions.
Rinse bath capacity : Output of 20 watts per liter or less.
Rinsing time : 5 min maximum.
Do not vibrate the PCB/PWB directly.
Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires.
2. CAPACITANCE CHANGE OF CAPACITORS
⋅ Class 1 capacitors
Capacitance might change a little depending on a surrounding temperature or an applied voltage.
Please contact us if you use for the strict time constant circuit.
⋅ Class 2 and 3 capacitors
Class 2 and 3 capacitors like temperature characteristic B, E and F have an aging characteristic,
whereby the capacitor continually decreases its capacitance slightly if the capacitor leaves for a long
time. Moreover, capacitance might change greatly depending on a surrounding temperature or an
applied voltage. So, it is not likely to be able to use for the time constant circuit.
Please contact us if you need a detail information.
3. PERFORMANCE CHECK BY EQUIPMENT
Before using a capacitor, check that there is no problem in the equipment's performance and the
specifications.
Generally speaking, CLASS 2 ceramic capacitors have voltage dependence characteristics and
temperature dependence characteristics in capacitance. So, the capacitance value may change
depending on the operating condition in an equipment. Therefore, be sure to confirm the apparatus
performance of receiving influence in a capacitance value change of a capacitor, such as leakage
current and noise suppression characteristic.
Moreover, check the surge-proof ability of a capacitor in the equipment, if needed, because the surge
voltage may exceed specific value by the inductance of the circuit.
NOTE
1.Please make sure that your product has been evaluated in view of your specifications with our
product being mounted to your product.
2.You are requested not to use our product deviating from this specification.
EGD28A
3 / 20
Reference only
1. Application
This specification is applied to Safety Standard Certified Lead Type Disc Ceramic Capacitors Type KJ
which can be used for the battery charger for Electric Vehicles and Plug-in Hybrid.
Type KJ is Safety Standard Certified capacitors of Class X1,Y2, and in accordance with AEC-Q200
requirements.
Approval standard and certified number
Standard number
*Certified number
UL/cUL
UL60384-14/CSA E60384-14
E37921
ENEC
(VDE)
EN60384-14
AC Rated voltage
V(r.m.s.)
X1:440
Y2:300
40031217
IEC60384-14
*Above Certified number may be changed on account of the revision of standards and
the renewal of certification.
2. Rating
2-1. Operating temperature range
-40 ∼
+125°C
2-2. Rated Voltage
X1:AC440V(r.m.s.)
Y2:AC300V(r.m.s.)
DC1kV
2-3. Part number configuration
ex.)
DE6
Series
E3
KJ
472
Temperature Certified Capacitance
Characteristics Type
M
Capacitance
Tolerance
A3
Lead
Style
B
Package
.
Individual
Specification
• Series
DE6 denotes class X1,Y2.
• Temperature Characteristics
Code
Temperature Characteristics
B3
B
E3
E
Please confirm detailed specification on [ Specification and test methods ].
• Certified Type
This denotes safety certified type name Type KJ.
• Capacitance
The first two digits denote significant figures ; the last digit denotes the multiplier of 10 in pF.
ex.) In case of 472.
47×102 = 4700pF
• Capacitance Tolerance
Please refer to [ Part number list ].
ETKJ01E
4 / 20
Reference only
• Lead Style
Code
Lead Style
A∗
Vertical crimp long type
B∗
Vertical crimp short type
N∗
Vertical crimp taping type
∗ Please refer to [ Part number list ].
Solder coated copper wire is applied for termination.
• Package
Code
B
A
Package
Bulk type
Ammo pack taping type
• Individual Specification
Murata’s control code
Please refer to Part number list .
Note) Murata part numbers might be changed depending on Lead Style or any other changes.
Therefore, please specify only the Certified Type (KJ) and capacitance of products in the
parts list when it is required for applying safety standard of electric equipment.
3. Marking
Capacitance
Capacitance tolerance
Certified type
Rated voltage mark
Class code
Manufacturing year
Manufacturing month
: 3 digit system
: Code
: KJ
: 300~
: X1Y2
: Letter code(The last digit of A.D. year.)
: Code
ex.) YEAR
2022
2D
∗
MONTH
12(December)
∗ From January to September : “1” to “9”,
October : “O” , November : “N” , December : “D”
Company name code
:
(Made in Thailand)
(Example)
472M
KJ 300～
X1Y2
2D
ETKJ01E
5 / 20
Reference only
4. Part number list
Unit : mm
T.C.
Cap.
(pF)
Cap.
tol.
Customer Part Number
Murata Part Number
Dimension (mm)
D
T
F
d
Pack
Lead
qty.
Style
(pcs)
B
100
±10%
DE6B3KJ101KA3BE01J
6.0
5.0
7.5
0.6
A3
250
B
150
±10%
DE6B3KJ151KA3BE01J
8.0
5.0
7.5
0.6
A3
250
B
220
±10%
DE6B3KJ221KA3BE01J
6.0
6.0
7.5
0.6
A3
250
B
330
±10%
DE6B3KJ331KA3BE01J
7.0
6.0
7.5
0.6
A3
250
B
470
±10%
DE6B3KJ471KA3BE01J
8.0
6.0
7.5
0.6
A3
250
B
680
±10%
DE6B3KJ681KA3BE01J
9.0
6.0
7.5
0.6
A3
250
E
1000
±20%
DE6E3KJ102MA3B
7.0
7.0
7.5
0.6
A3
250
E
1500
±20%
DE6E3KJ152MA3B
8.0
7.0
7.5
0.6
A3
250
E
2200
±20%
DE6E3KJ222MA3B
9.0
7.0
7.5
0.6
A3
250
E
3300
±20%
DE6E3KJ332MA3B
10.0
7.0
7.5
0.6
A3
250
E
4700
±20%
DE6E3KJ472MA3B
12.0
7.0
7.5
0.6
A3
200
6 / 20
Reference only
Unit : mm
T.C.
Cap.
(pF)
Cap.
tol.
Customer Part Number
Murata Part Number
Dimension (mm)
D
T
F
d
Pack
Lead
qty.
Style
(pcs)
B
100
±10%
DE6B3KJ101KA4BE01J
6.0
5.0 10.0
0.6
A4
250
B
150
±10%
DE6B3KJ151KA4BE01J
8.0
5.0 10.0
0.6
A4
250
B
220
±10%
DE6B3KJ221KA4BE01J
6.0
6.0 10.0
0.6
A4
250
B
330
±10%
DE6B3KJ331KA4BE01J
7.0
6.0 10.0
0.6
A4
250
B
470
±10%
DE6B3KJ471KA4BE01J
8.0
6.0 10.0
0.6
A4
250
B
680
±10%
DE6B3KJ681KA4BE01J
9.0
6.0 10.0
0.6
A4
250
E
1000
±20%
DE6E3KJ102MA4B
7.0
7.0 10.0
0.6
A4
250
E
1500
±20%
DE6E3KJ152MA4B
8.0
7.0 10.0
0.6
A4
250
E
2200
±20%
DE6E3KJ222MA4B
9.0
7.0 10.0
0.6
A4
250
E
3300
±20%
DE6E3KJ332MA4B
10.0
7.0 10.0
0.6
A4
250
E
4700
±20%
DE6E3KJ472MA4B
12.0
7.0 10.0
0.6
A4
200
7 / 20
Reference only
Unit : mm
T.C.
Cap.
(pF)
Cap.
tol.
Customer Part Number
Murata Part Number
Dimension (mm)
D
T
F
d
Pack
Lead
qty.
Style
(pcs)
B
100
±10%
DE6B3KJ101KB3BE01J
6.0
5.0
7.5
0.6
B3
500
B
150
±10%
DE6B3KJ151KB3BE01J
8.0
5.0
7.5
0.6
B3
500
B
220
±10%
DE6B3KJ221KB3BE01J
6.0
6.0
7.5
0.6
B3
500
B
330
±10%
DE6B3KJ331KB3BE01J
7.0
6.0
7.5
0.6
B3
500
B
470
±10%
DE6B3KJ471KB3BE01J
8.0
6.0
7.5
0.6
B3
500
B
680
±10%
DE6B3KJ681KB3BE01J
9.0
6.0
7.5
0.6
B3
500
E
1000
±20%
DE6E3KJ102MB3B
7.0
7.0
7.5
0.6
B3
500
E
1500
±20%
DE6E3KJ152MB3B
8.0
7.0
7.5
0.6
B3
500
E
2200
±20%
DE6E3KJ222MB3B
9.0
7.0
7.5
0.6
B3
500
E
3300
±20%
DE6E3KJ332MB3B
10.0
7.0
7.5
0.6
B3
500
E
4700
±20%
DE6E3KJ472MB3B
12.0
7.0
7.5
0.6
B3
250
8 / 20
Reference only
Unit : mm
T.C.
Cap.
(pF)
Cap.
tol.
Customer Part Number
Murata Part Number
Dimension (mm)
D
T
F
d
Pack
Lead
qty.
Style
(pcs)
B
100
±10%
DE6B3KJ101KB4BE01J
6.0
5.0 10.0
0.6
B4
500
B
150
±10%
DE6B3KJ151KB4BE01J
8.0
5.0 10.0
0.6
B4
500
B
220
±10%
DE6B3KJ221KB4BE01J
6.0
6.0 10.0
0.6
B4
500
B
330
±10%
DE6B3KJ331KB4BE01J
7.0
6.0 10.0
0.6
B4
500
B
470
±10%
DE6B3KJ471KB4BE01J
8.0
6.0 10.0
0.6
B4
500
B
680
±10%
DE6B3KJ681KB4BE01J
9.0
6.0 10.0
0.6
B4
500
E
1000
±20%
DE6E3KJ102MB4B
7.0
7.0 10.0
0.6
B4
500
E
1500
±20%
DE6E3KJ152MB4B
8.0
7.0 10.0
0.6
B4
500
E
2200
±20%
DE6E3KJ222MB4B
9.0
7.0 10.0
0.6
B4
500
E
3300
±20%
DE6E3KJ332MB4B
10.0
7.0 10.0
0.6
B4
500
E
4700
±20%
DE6E3KJ472MB4B
12.0
7.0 10.0
0.6
B4
250
9 / 20
Reference only
Unit : mm
T.C.
Cap.
(pF)
Cap.
tol.
Customer Part Number
Murata Part Number
Dimension (mm)
D
T
F
d
P
Pack
Lead
qty.
Style
(pcs)
B
100
±10%
DE6B3KJ101KN3AE01J
6.0
5.0
7.5
0.6 15.0 N3
700
B
150
±10%
DE6B3KJ151KN3AE01J
8.0
5.0
7.5
0.6 15.0 N3
700
B
220
±10%
DE6B3KJ221KN3AE01J
6.0
6.0
7.5
0.6 15.0 N3
700
B
330
±10%
DE6B3KJ331KN3AE01J
7.0
6.0
7.5
0.6 15.0 N3
700
B
470
±10%
DE6B3KJ471KN3AE01J
8.0
6.0
7.5
0.6 15.0 N3
700
B
680
±10%
DE6B3KJ681KN3AE01J
9.0
6.0
7.5
0.6 15.0 N3
700
E
1000
±20%
DE6E3KJ102MN3A
7.0
7.0
7.5
0.6 15.0 N3
700
E
1500
±20%
DE6E3KJ152MN3A
8.0
7.0
7.5
0.6 15.0 N3
700
E
2200
±20%
DE6E3KJ222MN3A
9.0
7.0
7.5
0.6 15.0 N3
700
E
3300
±20%
DE6E3KJ332MN3A
10.0
7.0
7.5
0.6 15.0 N3
700
E
4700
±20%
DE6E3KJ472MN3A
12.0
7.0
7.5
0.6 15.0 N3
700
10 / 20
Reference only
Unit : mm
T.C.
Cap.
(pF)
Cap.
tol.
Customer Part Number
Murata Part Number
Dimension (mm)
D
T
F
d
P
Pack
Lead
qty.
Style
(pcs)
B
100
±10%
DE6B3KJ101KN4AE01J
6.0
5.0 10.0
0.6 25.4 N4
400
B
150
±10%
DE6B3KJ151KN4AE01J
8.0
5.0 10.0
0.6 25.4 N4
400
B
220
±10%
DE6B3KJ221KN4AE01J
6.0
6.0 10.0
0.6 25.4 N4
400
B
330
±10%
DE6B3KJ331KN4AE01J
7.0
6.0 10.0
0.6 25.4 N4
400
B
470
±10%
DE6B3KJ471KN4AE01J
8.0
6.0 10.0
0.6 25.4 N4
400
B
680
±10%
DE6B3KJ681KN4AE01J
9.0
6.0 10.0
0.6 25.4 N4
400
E
1000
±20%
DE6E3KJ102MN4A
7.0
7.0 10.0
0.6 25.4 N4
400
E
1500
±20%
DE6E3KJ152MN4A
8.0
7.0 10.0
0.6 25.4 N4
400
E
2200
±20%
DE6E3KJ222MN4A
9.0
7.0 10.0
0.6 25.4 N4
400
E
3300
±20%
DE6E3KJ332MN4A
10.0
7.0 10.0
0.6 25.4 N4
400
E
4700
±20%
DE6E3KJ472MN4A
12.0
7.0 10.0
0.6 25.4 N4
400
11 / 20
Reference only
5. Specification and test methods
No.
Item
1
Appearance and dimensions
2
3
Marking
Capacitance
Specification
No marked defect on appearance
form.
Please refer to [Part number list] on
dimensions.
To be easily legible.
Within specified tolerance.
4
Dissipation Factor (D.F.)
2.5% max.
5
Insulation Resistance (I.R.)
10000MΩ min.
6
Dielectric
strength
Between lead
wires
No failure.
Body
insulation
No failure.
7
Temperature characteristic
Char. B : Within ±10 %
Char. E : Within +20/-55%
(Temp. range : -25 to +85°C )
Test method
The capacitor should be inspected by naked eyes
for visible evidence of defect.
Dimensions should be measured with slide
calipers.
The capacitor should be inspected by naked eyes.
The capacitance should be measured at 20°C with
1±0.1kHz and AC5V(r.m.s.)max..
The dissipation factor should be measured at 20°C
with 1±0.1kHz and AC5V(r.m.s.) max..
The insulation resistance should be measured
with DC500±50V within 60±5 s of charging.
The voltage should be applied to the capacitor
through a resistor of 1MΩ.
The capacitor should not be damaged when
AC2600V(r.m.s.) is applied between
the lead wires for 60 s.
First, the terminals of the capacitor should be
connected together.
Then, a metal foil should
be closely wrapped around
the body of the capacitor
Metal
About
foil
to the distance of
3 to 4 mm
about 3 to 4mm
Metal
from each terminal.
balls
Then, the capacitor should be inserted into a
container filled with metal balls of about 1mm
diameter. Finally, AC2600V (r.m.s.) is
applied for 60 s between the capacitor lead wires
and metal balls.
The capacitance measurement should be made at
each step specified in Table.
Step
1
2
3
4
5
Temp.(°C)
20±2
-25±2
20±2
85±2
20±2
•Pre-treatment
Capacitor should be stored at 125±3°C for 1 h, then placed at *room condition for 24±2 h
before initial measurements.
8
Solderability
Lead wire should be soldered
Should be placed into steam aging for 8 h±15min.
with uniform coating on the axial
After the steam aging, the lead wire of a capacitor
direction over 3/4 of the
should be dipped into a ethanol solution of 25%
circumferential direction.
rosin and then into molten solder for 5+0/-0.5 sec.
The depth of immersion is up to about 1.5 to 2.0mm
from the root of lead wires.
Temp. of solder:
Lead Free Solder(Sn-3Ag-0.5Cu) 245±5°C
H63 Eutectic Solder 235±5°C
* "room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
ESKJ01H
12 / 20
Reference only
No.
9
Resistance to
Soldering Heat
(Non-preheat)
Item
Appearance
Capacitance
change
I.R.
Dielectric
Strength
10
11
12
13
Resistance to
Soldering Heat
(On-preheat)
Vibration
Mechanical
Shock
(Compliant with
AEC-Q200)
Humidity
(Under steady
state)
Appearance
Capacitance
change
I.R.
Dielectric
strength
Appearance
Capacitance
D.F.
Specification
No marked defect.
Within ± 10%
1000MΩ min.
Per Item 6
No marked defect.
Within ±10%
1000MΩ min.
Per item 6
No marked defect.
Within the specified tolerance.
2.5% max.
Appearance
Capacitance
D.F.
No marked defect.
Within the specified tolerance.
5.0% max.
I.R.
10000MΩ min.
Appearance
Capacitance
change
D.F.
Test method
As shown in figure, the lead wires should be
immersed in solder of 260±5°C up to 1.5 to 2.0mm
from the root of terminal for 10±1 s.
No marked defect.
Char. B : Within ±10%
Char. E : Within ±15%
5.0% max.
•Pre-treatment
Capacitor should be stored at 125±3°C for 1 h,
then placed at *room condition for 24±2 h before
initial measurements.
•Post-treatment
Capacitor should be stored for 1 to 2 h at *room
condition.
First the capacitor should be stored at 120+0/-5°C
for 60+0/-5 s.
Then, as in figure, the lead wires should be
immersed solder of 260+0/-5°C up to 1.5 to 2.0mm
from the root of terminal for 7.5+0/-1 s.
Pre-treatment : Capacitor should be stored at
125±3°C for 1 h, then placed at
*1room condition for 24±2 h
before initial measurements.
Post-treatment : Capacitor should be stored for 1 to
2 h at *1room condition.
Solder the capacitor and gum up the body to the
test jig (glass epoxy board) by resin(adhesive).
resin(adhesive)
The capacitor should be firmly soldered to the
supporting lead wire, 1.5mm in total amplitude, with
about 20 minutes rate of vibration change from
10Hz to 2000Hz and back to 10Hz.
This motion should be applied for 12 times in each 3
mutually perpendicular directions (total of 36 times).
The acceleration is 5g max..
Solder the capacitor and gum up the body to the
test jig (glass epoxy board) by resin(adhesive).
resin(adhesive)
Three shocks in each direction should be applied
along 3 mutually perpendicular axes to and from of
the test specimen (18 shocks).
The specified test pulse should be Half-sine and
should have a duration :0.5ms, peak value:100g
and velocity change: 4.7m/s.
Set the capacitor for 1000±12 h at 85±3°C in 80 to
85% relative humidity.
•Pre-treatment
Capacitor should be stored at 125±3°C for 1 h,
then placed at *room condition for 24±2 h before
I.R.
3000MΩ min.
initial measurements.
Dielectric
Per item 6
•Post-treatment
strength
Capacitor should be stored for 1 to 2 h at *room
condition.
* "room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
ESKJ01H
13 / 20
Reference only
No.
14
15
Item
Humidity loading
Appearance
Capacitance
change
D.F.
Life
Specification
No marked defect.
Char. B : Within ±10%
Char. E : Within ±15%
5.0% max.
I.R.
3000MΩ min.
Dielectric
strength
Capacitance
change
I.R.
No marked defect.
Dielectric
strength
Within ± 20%
3000MΩ min.
Per item 6
Test method
Apply the rated voltage for 1000±12 h at 85±3°C in
80 to 85% relative humidity.
•Pre-treatment
Capacitor should be stored at 125±3°C for 1 h,
then placed at *room condition for 24±2 h before
initial measurements.
•Post-treatment
Capacitor should be stored for 1 to 2 h at *room
condition.
Impulse voltage
Each individual capacitor should be subjected to
a 5kV impulses for three times. Then the
capacitors are applied to life test.
Front time (T1) = 1.7μs=1.67T
Time to half-value (T2) = 50μs
The capacitors are placed in a circulating air oven
for a period of 1000 h.
The air in the oven is maintained at a temperature
of 125+2/-0°C, and relative humidity of 50% max..
Throughout the test, the capacitors are subjected
to a AC510V(r.m.s.) alternating voltage
of mains frequency, except that once each hour
the voltage is increased to AC1000V(r.m.s.) for
0.1 s.
16
Flame test
The capacitor flame discontinue
as follows.
Cycle
Time
1 to 4
30 s max.
5
60 s max.
•Pre-treatment
Capacitor should be stored at 125±3°C for 1 h,
then placed at *room condition for 24±2 h before
initial measurements.
•Post-treatment
Capacitor should be stored for 1 to 2 h at *room
condition.
The capacitor should be subjected to applied
flame for 15 s. and then removed for 15 s until 5
cycles are completed.
(in mm)
As shown in the figure at right, fix
the body of the capacitor and apply
a tensile weight gradually to each
lead wire in the radial direction of the
capacitor up to 10N, and keep it
for 10±1 s.
Bending
Each lead wire should be subjected to 5N of
weight and bent 90° at the point of egress, in one
direction, then returned to its original position, and
bent 90° in the opposite direction at the rate of one
bend in 2 to 3 s.
* "room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
17
Robustness of
terminations
ESKJ01H
Tensile
Lead wire should not cut off.
Capacitor should not be broken.
14 / 20
Reference only
No.
18
Item
Active flammability
Specification
The cheese-cloth should not be on
fire.
Test method
The capacitors should be individually wrapped in
at least one, but not more than two, complete layers
of cheese-cloth. The capacitor should be subjected
to 20 discharges. The interval between successive
discharges should be 5 s. The UAc should be
maintained for 2min after the last discharge.
C1,2
: 1µF±10%, C3 : 0.033µF±5% 10kV
L1 to L4 : 1.5mH±20% 16A Rod core choke
R
: 100Ω±2%, Ct : 3µF±5% 10kV
UAc
: UR ±5% UR : Rated working voltage
Cx
: Capacitor under test
F
: Fuse, Rated 10A
Ut
: Voltage applied to Ct
19
Passive flammability
The burning time should not be
exceeded the time 30 s.
The tissue paper should not
ignite.
The capacitor under test should be held in the flame
in the position which best promotes burning.
Time of exposure to flame is for 30 s.
Length of flame : 12±1mm
Gas burner : Length 35mm min.
Inside Dia.
0.5±0.1mm
Outside Dia. 0.9mm max.
Gas : Butane gas Purity 95% min.
Capacitor
About 8mm
Flame
Gas burner
45°
200±5mm
Tissue
About 10mm thick board
20
21
Temperature
Cycle
(Compliant with
AEC-Q200)
High Temperature
Exposure
(Storage)
(Compliant with
AEC-Q200)
Appearance
Capacitance
change
D.F.
I.R.
Dielectric
strength
Capacitance
change
D.F.
I.R.
No marked defect.
Char. B : Within ±10%
Char. E : Within ±20%
5.0% max.
3000MΩ min.
Per Item 6.
The capacitor should be subjected to
1000 temperature cycles.
Step
1
2
3
4
Temperature(°C)
-55+0/-3
Room temp.
+125+3/-0
Room temp.
Time(min.)
30
3
30
3
•Pre-treatment
Capacitor should be stored at 125±3°C for 1 h, then
placed at *room condition for 24±2 h.
•Post-treatment
Capacitor should be stored for 24±2 h at *room
condition.
Sit the capacitor for 1,000±12 h at 150±3°C.
Within ± 20%
•Pre-treatment
Capacitor should be stored at 125±3°C for 1 h, then
placed at *room condition for 24±2 h.
•Post-treatment
Capacitor should be stored for 24±2 h at *room
condition.
* "room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
ESKJ01H
5.0% max.
1000MΩ min.
15 / 20
Reference only
No.
22
23
24
Resistance to
Solvents
(Compliant with
AEC-Q200)
Biased Humidity
(Compliant with
AEC-Q200)
Moisture
Resistance
(Compliant with
AEC-Q200)
Specification
No marked defect except
color change of outer
coating.
Char. B : Within ±10%
Char. E : Within ±20%
5.0% max.
3000MΩ min.
Test method
The capacitor should be subjected to 300 cycles.
Step
Temperature(°C) Time(min.)
1
-55+0/-3
30
2
125+3/0
30
•Pre-treatment
Capacitor should be stored at 125±3°C for 1 h, then placed at
*room condition for 24±2 h.
•Post-treatment
Capacitor should be stored for 24±2 h at *room condition.
Per MIL-STD-202 Method 215
Solvent 1 : 1 part (by volume) of isopropyl alcohol
3 parts (by volume) of mineral spirits
Solvent 2 : Terpene defluxer
Solvent 3 : 42 parts (by volume) of water
1part (by volume) of propylene glycol
monomethyl ether
1 part (by volume) of monoethanolomine
Appearance
Capacitance
change
D.F.
No marked defect.
Char. B : Within ±10%
Char. E : Within ±20%
5.0% max.
I.R.
3000MΩ min.
Appearance
Capacitance
change
D.F.
I.R.
No marked defect.
Char. B : Within ±10%
Char. E : Within ±15%
5.0% max.
3000MΩ min.
Apply DC1.3+0.2/-0 V (add 100kΩ resistor) at 85±3°C and 80
to 85% humidity for 1,000±12 h.
The charge/discharge current is less than 50mA
Appearance
Capacitance
change
D.F.
I.R.
No marked defect.
Char. B : Within ±10%
Char. E : Within ±20%
5.0% max.
3000MΩ min.
Apply the 24 h heat(25 to 65°C) and humidity(80 to
98%) treatment shown below, 10 consecutive times.
•Pre-treatment
Capacitor should be stored at 125±3°C for 1 h, then placed at
*room condition for 24±2 h.
•Post-treatment
Capacitor should be stored for 24±2 h at *room condition.
Temperature
Humidity
(°C)
90∼98%
70
65
60
55
50
45
40
35
30
25
20
15
10
Initial measurement
5
0
-5
-10
Humidity
80∼98%
Humidity
90∼98%
Humidity
80∼98%
Humidity
90∼98%
Temperature
25
Item
Thermal Shock
Appearance
(Compliant with
AEC-Q200)
Capacitance
change
D.F.
I.R.
0 1 2
+10
- 2 °C
One cycle 24 hours
3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Hours
•Post-treatment
Capacitor should be stored for 24±2 h at *room condition.
* "room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
ESKJ01H
16 / 20
Reference only
6.Packing specification
•Bulk type (Package : B)
The size of packing case and packing way
∗1
∗2
The number of packing = Packing quantity × n
Polyethylene bag
∗1 : Please refer to [Part number list].
∗2 : Standard n = 20 (bag)
Partition
270 max.
125 max.
340 max.
Note)
The outer package and the number of
outer packing be changed by the order
getting amount.
Unit : mm
•Ammo pack taping type (Package : A)
⋅ The tape with capacitors is packed zigzag into a case.
⋅ When body of the capacitor is piled on other body under it.
⋅ There should be 3 pitches and over without capacitors in leader and trailer.
The size of packing case and packing way
240 max.
Position of label
340 max.
60 max.
Capacitor
Hold down tape
Base tape
Hold down
tape upper
EKBCDE01A
17 / 20
Unit : mm
Reference only
7. Taping specification
7-1. Dimension of capacitors on tape
Vertical crimp taping type < Lead Style : N3 >
Pitch of component 15.0mm / Lead spacing 7.5mm
Unit : mm
Item
Code
Dimensions
Remarks
Pitch of component
P
15.0±2.0
Pitch of sprocket hole
P0
15.0±0.3
Lead spacing
F
7.5±1.0
Length from hole center to component center
P2
7.5±1.5
Length from hole center to lead
P1
3.75±1.0
Body diameter
D
Please refer to [ Part number list ].
Deviation along tape, left or right
∆S
0±2.0
Carrier tape width
W
18.0±0.5
Position of sprocket hole
W1
9.0±0.5
H0
18.0± 2.0
0
Lead distance between reference and bottom
planes
Deviation of progress direction
They include deviation by lead bend .
Deviation of tape width direction
+0.5∼−1.0
Protrusion length
Diameter of sprocket hole
φD0
4.0±0.1
Lead diameter
φd
0.60±0.05
Total tape thickness
t1
0.6±0.3
Total thickness, tape and lead wire
t2
1.5 max.
Deviation across tape, front
∆h1
Deviation across tape, rear
∆h2
Portion to cut in case of defect
L
11.0± 1.0
Hold down tape width
W0
11.5 min.
Hold down tape position
W2
1.5±1.5
Coating extension on lead
e
Up to the end of crimp
Body thickness
T
Please refer to [ Part number list ].
ETP1N301B
They include hold down tape thickness.
2.0 max.
0
18 / 20
Reference only
Vertical crimp taping type < Lead Style : N4 >
Pitch of component 25.4mm / Lead spacing 10.0mm
∗
Unit : mm
Item
Code
Dimensions
Remarks
Pitch of component
P
25.4±2.0
Pitch of sprocket hole
P0
12.7±0.3
Lead spacing
F
10.0±1.0
Length from hole center to lead
P1
7.7±1.5
Body diameter
D
Please refer to [ Part number list ].
Deviation along tape, left or right
∆S
0±2.0
Carrier tape width
W
18.0±0.5
Position of sprocket hole
W1
9.0±0.5
H0
18.0± 0
Lead distance between reference and
bottom planes
They include deviation by lead bend .
Deviation of tape width direction
2.0
+0.5∼−1.0
Protrusion length
Diameter of sprocket hole
φD0
4.0±0.1
Lead diameter
φd
0.60±0.05
Total tape thickness
t1
0.6±0.3
Total thickness, tape and lead wire
t2
1.5 max.
Deviation across tape, front
∆h1
Deviation across tape, rear
∆h2
Portion to cut in case of defect
L
11.0± 1.0
Hold down tape width
W0
11.5 min.
Hold down tape position
W2
1.5±1.5
Coating extension on lead
e
Up to the end of crimp
Body thickness
T
Please refer to [ Part number list ].
ETP1N401B
They include hold down tape thickness.
2.0 max.
0
19 / 20
Reference only
7-2. Splicing way of tape
1) Adhesive force of tape is over 3N at test condition as below.
W
Hold down tape
Base tape
2) Splicing of tape
a) When base tape is spliced
•Base tape should be spliced by cellophane tape.
(Total tape thickness should be less than 1.05mm.)
Progress direction
in production line
Hold down tape
Base tape
About 30 to 50
Cellophane tape
No lifting for the direction of
progressing
Unit : mm
b) When hold down tape is spliced
•Hold down tape should be spliced with overlapping.
(Total tape thickness should be less than 1.05mm.)
ape are spliced
•Base tape and adhesive tape should be spliced with splicing tape.
20 to 60
Hold down tape
Progress direction
in production line
Base tape
Unit : mm
c) When both tape are spliced
•Base tape and hold down tape should be spliced with splicing tape.
3 ) Missing components
•There should be no consecutive missing of more than three components.
•The number of missing components should be not more than 0.5% of
total components that should be present in a Ammo pack.
ETP2D03
20 / 20
工商网监
湘ICP备2023018690号
