Reference Specification
DEA Series
High Temperature Lead Type Disc Ceramic Capacitors of Class 1 for General Purpose
Product specifications in this catalog are as of Dec. 2017, and are subject to change or
obsolescence without notice.
Please consult the approval sheet before ordering.Please read rating and Cautions first.
Reference only
CAUTION
1. OPERATING VOLTAGE
When DC-rated capacitors are to be used in AC or ripple current circuits, be sure to maintain the Vp-p
value of the applied voltage or the Vo-p which contains DC bias within the rated voltage range.
When the voltage is started to apply to the circuit or it is stopped applying, the irregular voltage may
be generated for a transit period because of resonance or switching. Be sure to use a capacitor
within rated voltage containing these irregular voltage.
When DC-rated capacitors are to be used in input circuits from commercial power source (AC filter),
be sure to use Safety Recognized Capacitors because various regulations on withstand voltage
or impulse withstand established for each equipment should be taken into considerations.
Voltage
DC Voltage
DC+AC Voltage
AC Voltage
Pulse Voltage(1) Pulse Voltage(2)
Positional Vo-p
Measurement
Vo-p
Vp-p
Vp-p
Vp-p
2. OPERATING TEMPERATURE AND SELF-GENERATED HEAT
Keep the surface temperature of a capacitor below the upper limit of its rated operating temperature
range. Be sure to take into account the heat generated by the capacitor itself.
When the capacitor is used in a high-frequency current, pulse current or the like, it may have the selfgenerated heat due to dielectric-loss. The allowable frequency should be in less than 300kHz in sine
wave. Applied voltage should be the load such as self-generated heat is within 5 °C on the condition of
atmosphere temperature 25 °C. When measuring, use a thermocouple of small thermal capacity-K of
φ0.1mm and be in the condition where capacitor is not affected by radiant heat of other components and
wind of surroundings. (Never attempt to perform measurement with the cooling fan running. Otherwise,
accurate measurement cannot be ensured.)
3. FAIL-SAFE
When capacitor would be broken, failure may result in a short circuit. Be sure to provide an appropriate
fail-safe function like a fuse on your product if failure would follow an electric shock, fire or fume.
4. LOAD REDUCTION AND SELF-GENERATED HEAT DURING APPLICATION OF
HIGH-FREQUENCY AND HIGH-VOLTAGE
Since the heat generated by the low-dissipation capacitor itself is low, its allowable power is much higher
than the general B characteristic. However, in case such an applied load that the self-heating temperature
is 20 °C at the rated voltage, the allowable power may be exceeded.
Therefore, when using the low-dissipation capacitors in a high-frequency and high-voltage circuit with a
frequency of 1kHz or higher, make sure that the Vp-p values including the DC bias, do not exceed the
applied voltage value specified in Table 1. Also make sure that the self-heating temperature (the
difference between the capacitor’s surface temperature and the capacitor’s ambient temperature) at an
ambient temperature of 25 °C does not exceed the value specified in Table 1.
As shown in Fig. 1, the self-heating temperature depends on the ambient temperature. Therefore, if you
are not able to set the ambient temperature to approximately 25 °C, please contact our sales
representatives or product engineers.
Allowable Conditions at High-frequency
SL
Allowable Conditions at High-frequency *2
Self-heating Temp.
(25 °C Ambient Temp.)
Capacitor’s
Ambient
Temp. *1
1kV
Applied Voltage
(max.)
1000Vp-p
2kV
2000Vp-p
5 °C max.
-25 to +85 °C
Temp. DC Rated
Char.
Voltage
3.15kV
3150Vp-p
*1 When the ambient temperature is 85 to 125 °C, the applied voltage needs to be further reduced.
If the low-dissipation capacitors needs to be used at an ambient temperature of 85 to 125 °C,
please contact our sales representatives or product engineers.
*2 Fig. 2 shows reference data on the allowable voltage-frequency characteristic for a sine wave
voltage.
EGD20E
1 / 21
Reference only
Dependence of Self-heating Temperature on Ambient Temperature
Allowable Voltage (Sine Wave Voltage) – Frequency Characteristic [At Ambient Temperature of
85 °C or less]
Because of the influence of harmonics, when the applied voltage is a rectangular wave or pulse wave
voltage (instead of a sine wave voltage), the heat generated by the capacitor is higher than the value
obtained by application of the sine wave with the same fundamental frequency. Roughly calculated for
reference, the allowable voltage for a rectangular wave or pulse wave corresponds approximately to the
allowable voltage for a sine wave whose fundamental frequency is twice as large as that of the rectangular
wave or pulse wave. This allowable voltage, however, varies depending on the voltage and current
waveforms. Therefore, you are requested to make sure that the self-heating temperature is not higher than
the value specified in Table 1.
5. VIBRATION AND IMPACT
Do not expose a capacitor or its leads to excessive shock or vibration during use.
6. SOLDERING
When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification
of the capacitor. Subjecting this product to excessive heating could melt the internal junction solder
and may result in thermal shocks that can crack the ceramic element.
When soldering capacitor with a soldering iron, it should be performed in following conditions.
Temperature of iron tip : 400 °C max.
Soldering iron wattage : 50W max.
Soldering time
: 3.5 s max.
EGD20E
2 / 21
Reference only
7. BONDING, RESIN MOLDING AND COATING
In case of bonding, molding or coating this product, verify that these processes do not affect the
quality of capacitor by testing the performance of the bonded, molded or coated product in the
intended equipment.
In case of the amount of applications, dryness / hardening conditions of adhesives and molding
resins containing organic solvents (ethyl acetate, methyl ethyl ketone, toluene, etc.) are unsuitable,
the outer coating resin of a capacitor is damaged by the organic solvents and it may result, worst
case, in a short circuit.
The variation in thickness of adhesive, molding resin or coating may cause a outer coating resin
cracking and/or ceramic element cracking of a capacitor in a temperature cycling.
8. TREATMENT AFTER BONDING, RESIN MOLDING AND COATING
When the outer coating is hot (over 100 ℃) after soldering, it becomes soft and fragile.
So please be careful not to give it mechanical stress.
Failure to follow the above cautions may result, worst case, in a short circuit and cause fuming
or partial dispersion when the product is used.
9. OPERATING AND STORAGE ENVIRONMENT
The insulating coating of capacitors does not form a perfect seal; therefore, do not use or store
capacitors in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the
like are present. And avoid exposure to moisture. Before cleaning, bonding, or molding this product,
verify that these processes do not affect product quality by testing the performance of a cleaned, bonded
or molded product in the intended equipment. Store the capacitors where the temperature and relative
humidity do not exceed -10 to 40 °C and 15 to 85%. Use capacitors within 6 months after
delivered. Check the solderability after 6 months or more.
10. LIMITATION OF APPLICATIONS
Please contact us before using our products for the applications listed below which require especially
high reliability for the prevention of defects which might directly cause damage to the third party’s life,
body or property.
1. Aircraft equipment
2. Aerospace equipment
3. Undersea equipment
4. Power plant control equipment
5. Medical equipment
6. Transportation equipment (vehicles, trains, ships, etc.)
7. Traffic signal equipment
8. Disaster prevention / crime prevention equipment
9. Data-processing equipment exerting influence on public
10. Application of similar complexity and/or reliability requirements to the applications listed
in the above.
EGD20E
3 / 21
Reference only
NOTICE
1. CLEANING (ULTRASONIC CLEANING)
To perform ultrasonic cleaning, observe the following conditions.
Rinse bath capacity : Output of 20 watts per liter or less.
Rinsing time : 5 min maximum.
Do not vibrate the PCB/PWB directly.
Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires.
2. CAPACITANCE CHANGE OF CAPACITORS
- Class 1 capacitors
Capacitance might change a little depending on a surrounding temperature or an applied voltage.
Please contact us if you use for the strict time constant circuit.
- Class 2 and 3 capacitors
Class 2 and 3 capacitors like temperature characteristic B, E and F have an aging characteristic,
whereby the capacitor continually decreases its capacitance slightly if the capacitor leaves for a long
time. Moreover, capacitance might change greatly depending on a surrounding temperature or an
applied voltage. So, it is not likely to be able to use for the time constant circuit.
Please contact us if you need a detail information.
NOTE
1.Please make sure that your product has been evaluated in view of your specifications with our
product being mounted to your product.
2.You are requested not to use our product deviating from this specification.
EGD20E
4 / 21
Reference only
1. Application
This specification is applied to High Temperature Lead Type Disc Ceramic Capacitors of
DC2kV ～3.15kV ratings and Class 1 of DEA series used for General Electric equipment.
Do not use these products in any automotive power train or safety equipment including battery chargers
for electric vehicles and plug-in hybrids.
2. Rating
2-1. Operating temperature range
-25
+125C
2-2. Part number configuration
ex.)
DEA
Series
1X
3D
561
J
B3
B
Temperature Rated Capacitance Capacitance Lead
Packing
Individual
characteristic voltage
tolerance
code style code specification
.
Temperature characteristic
Code
Temperature characteristic
1X
SL
Please confirm detailed specification on Specification and test methods .
Rated voltage
Code
3D
3F
Rated voltage
DC2kV
DC3.15kV
Capacitance
The first two digits denote significant figures ; the last digit denotes the multiplier of 10 in pF.
ex.) In case of 561.
56101 = 560pF
Capacitance tolerance
Please refer to Part number list .
Lead code
Code
Lead style
Vertical crimp long type
A
Straight long type
C
Vertical crimp short type
B
Straight short type
D
Vertical crimp taping type
N
Straight taping type
P
Please refer to Part number list .
Solder coated copper wire is applied for termination.
Packing style code
Code
B
A
Packing type
Bulk type
Ammo pack taping type
Individual specification
In case part number cannot be identified without ‘individual specification’ , it is added at
the end of part number.
5 / 21
Reference only
3. Marking
Nominal capacitance
Capacitance tolerance
Rated voltage
Company name code
Manufacturing year
Manufacturing month
: Actual value(under 100pF)
3 digit system(100pF and over)
: Code
(Omitted for maximum body diameter 6mm and under)
: Letter code(In case of DC3.15kV, marked with 3KV)
: Abbreviation
(Omitted for maximum body diameter 9mm and under)
: Letter code(The last digit of A.D. year.)
(Omitted for maximum body diameter 5mm and under)
: Code
(Omitted for maximum body diameter 5mm and under)
Feb./Mar. 2
Aug./Sep. 8
Apr./May 4
Oct./Nov. O
Jun./Jul. 6
Dec./Jan. D
(Example)
561J
2KV
6 / 21
Reference only
4. Part number list
Unit : mm
T.C.
Cap.
(pF)
Cap.
tol.
Customer Part Number
Murata Part Number
Dimension (mm)
DC
Rated Volt.
(V)
D
T
F
d
Lead
Code
Pack
qty.
(pcs)
SL
10
±5%
DEA1X3D100JC1B
2000
4.5
5.0
5.0
0.5
C1
500
SL
12
±5%
DEA1X3D120JC1B
2000
4.5
5.0
5.0
0.5
C1
500
SL
15
±5%
DEA1X3D150JC1B
2000
4.5
5.0
5.0
0.5
C1
500
SL
18
±5%
DEA1X3D180JC1B
2000
4.5
5.0
5.0
0.5
C1
500
SL
22
±5%
DEA1X3D220JC1B
2000
4.5
5.0
5.0
0.5
C1
500
SL
27
±5%
DEA1X3D270JC1B
2000
4.5
5.0
5.0
0.5
C1
500
SL
33
±5%
DEA1X3D330JC1B
2000
4.5
5.0
5.0
0.5
C1
500
SL
39
±5%
DEA1X3D390JC1B
2000
5.0
5.0
5.0
0.5
C1
500
SL
47
±5%
DEA1X3D470JA2B
2000
6.0
5.0
5.0
0.6
A2
500
SL
56
±5%
DEA1X3D560JA2B
2000
6.0
5.0
5.0
0.6
A2
500
SL
68
±5%
DEA1X3D680JA2B
2000
6.0
5.0
5.0
0.6
A2
500
SL
82
±5%
DEA1X3D820JA2B
2000
7.0
5.0
5.0
0.6
A2
500
SL
100
±5%
DEA1X3D101JA2B
2000
7.0
5.0
5.0
0.6
A2
500
SL
120
±5%
DEA1X3D121JA2B
2000
8.0
5.0
5.0
0.6
A2
250
SL
150
±5%
DEA1X3D151JA2B
2000
8.0
5.0
5.0
0.6
A2
250
SL
180
±5%
DEA1X3D181JA2B
2000
9.0
5.0
5.0
0.6
A2
250
SL
220
±5%
DEA1X3D221JA2B
2000
10.0
5.0
5.0
0.6
A2
250
SL
270
±5%
DEA1X3D271JA2B
2000
11.0
5.0
5.0
0.6
A2
250
SL
330
±5%
DEA1X3D331JA3B
2000
12.0
5.0
7.5
0.6
A3
200
SL
390
±5%
DEA1X3D391JA3B
2000
13.0
5.0
7.5
0.6
A3
200
SL
470
±5%
DEA1X3D471JA3B
2000
14.0
5.0
7.5
0.6
A3
200
SL
560
±5%
DEA1X3D561JA3B
2000
15.0
5.0
7.5
0.6
A3
100
SL
10
±5%
DEA1X3F100JCDB
3150
5.0
6.0
7.5
0.5
CD
500
SL
12
±5%
DEA1X3F120JCDB
3150
5.0
6.0
7.5
0.5
CD
500
SL
15
±5%
DEA1X3F150JCDB
3150
5.0
6.0
7.5
0.5
CD
500
SL
18
±5%
DEA1X3F180JCDB
3150
5.0
6.0
7.5
0.5
CD
500
SL
22
±5%
DEA1X3F220JCDB
3150
5.0
6.0
7.5
0.5
CD
500
7 / 21
Reference only
Unit : mm
T.C.
Cap.
(pF)
Cap.
tol.
Customer Part Number
Murata Part Number
Dimension (mm)
DC
Rated Volt.
(V)
D
T
F
d
Lead
Code
Pack
qty.
(pcs)
SL
27
±5%
DEA1X3F270JC3B
3150
6.0
6.0
7.5
0.6
C3
500
SL
33
±5%
DEA1X3F330JC3B
3150
6.0
6.0
7.5
0.6
C3
500
SL
39
±5%
DEA1X3F390JC3B
3150
6.0
6.0
7.5
0.6
C3
500
SL
47
±5%
DEA1X3F470JC3B
3150
7.0
6.0
7.5
0.6
C3
250
SL
56
±5%
DEA1X3F560JC3B
3150
7.0
6.0
7.5
0.6
C3
250
SL
68
±5%
DEA1X3F680JA3B
3150
8.0
6.0
7.5
0.6
A3
250
SL
82
±5%
DEA1X3F820JA3B
3150
8.0
6.0
7.5
0.6
A3
250
SL
100
±5%
DEA1X3F101JA3B
3150
9.0
6.0
7.5
0.6
A3
250
SL
120
±5%
DEA1X3F121JA3B
3150
10.0
6.0
7.5
0.6
A3
250
SL
150
±5%
DEA1X3F151JA3B
3150
11.0
6.0
7.5
0.6
A3
250
SL
180
±5%
DEA1X3F181JA3B
3150
11.0
6.0
7.5
0.6
A3
250
SL
220
±5%
DEA1X3F221JA3B
3150
12.0
6.0
7.5
0.6
A3
200
SL
270
±5%
DEA1X3F271JA3B
3150
14.0
6.0
7.5
0.6
A3
200
SL
330
±5%
DEA1X3F331JA3B
3150
15.0
6.0
7.5
0.6
A3
100
SL
390
±5%
DEA1X3F391JA3B
3150
16.0
6.0
7.5
0.6
A3
100
8 / 21
Reference only
Unit : mm
T.C.
Cap.
(pF)
Cap.
tol.
Customer Part Number
Murata Part Number
Dimension (mm)
DC
Rated Volt.
(V)
D
T
F
d
Lead
Code
Pack
qty.
(pcs)
SL
10
±5%
DEA1X3D100JD1B
2000
4.5
5.0
5.0
0.5
D1
500
SL
12
±5%
DEA1X3D120JD1B
2000
4.5
5.0
5.0
0.5
D1
500
SL
15
±5%
DEA1X3D150JD1B
2000
4.5
5.0
5.0
0.5
D1
500
SL
18
±5%
DEA1X3D180JD1B
2000
4.5
5.0
5.0
0.5
D1
500
SL
22
±5%
DEA1X3D220JD1B
2000
4.5
5.0
5.0
0.5
D1
500
SL
27
±5%
DEA1X3D270JD1B
2000
4.5
5.0
5.0
0.5
D1
500
SL
33
±5%
DEA1X3D330JD1B
2000
4.5
5.0
5.0
0.5
D1
500
SL
39
±5%
DEA1X3D390JD1B
2000
5.0
5.0
5.0
0.5
D1
500
SL
47
±5%
DEA1X3D470JB2B
2000
6.0
5.0
5.0
0.6
B2
500
SL
56
±5%
DEA1X3D560JB2B
2000
6.0
5.0
5.0
0.6
B2
500
SL
68
±5%
DEA1X3D680JB2B
2000
6.0
5.0
5.0
0.6
B2
500
SL
82
±5%
DEA1X3D820JB2B
2000
7.0
5.0
5.0
0.6
B2
500
SL
100
±5%
DEA1X3D101JB2B
2000
7.0
5.0
5.0
0.6
B2
500
SL
120
±5%
DEA1X3D121JB2B
2000
8.0
5.0
5.0
0.6
B2
500
SL
150
±5%
DEA1X3D151JB2B
2000
8.0
5.0
5.0
0.6
B2
500
SL
180
±5%
DEA1X3D181JB2B
2000
9.0
5.0
5.0
0.6
B2
500
SL
220
±5%
DEA1X3D221JB2B
2000
10.0
5.0
5.0
0.6
B2
500
SL
270
±5%
DEA1X3D271JB2B
2000
11.0
5.0
5.0
0.6
B2
500
SL
330
±5%
DEA1X3D331JB3B
2000
12.0
5.0
7.5
0.6
B3
250
SL
390
±5%
DEA1X3D391JB3B
2000
13.0
5.0
7.5
0.6
B3
250
SL
470
±5%
DEA1X3D471JB3B
2000
14.0
5.0
7.5
0.6
B3
250
SL
560
±5%
DEA1X3D561JB3B
2000
15.0
5.0
7.5
0.6
B3
200
SL
10
±5%
DEA1X3F100JDDB
3150
5.0
6.0
7.5
0.5
DD
500
SL
12
±5%
DEA1X3F120JDDB
3150
5.0
6.0
7.5
0.5
DD
500
SL
15
±5%
DEA1X3F150JDDB
3150
5.0
6.0
7.5
0.5
DD
500
SL
18
±5%
DEA1X3F180JDDB
3150
5.0
6.0
7.5
0.5
DD
500
SL
22
±5%
DEA1X3F220JDDB
3150
5.0
6.0
7.5
0.5
DD
500
9 / 21
Reference only
Unit : mm
T.C.
Cap.
(pF)
Cap.
tol.
Customer Part Number
Murata Part Number
Dimension (mm)
DC
Rated Volt.
(V)
D
T
F
d
Lead
Code
Pack
qty.
(pcs)
SL
27
±5%
DEA1X3F270JD3B
3150
6.0
6.0
7.5
0.6
D3
500
SL
33
±5%
DEA1X3F330JD3B
3150
6.0
6.0
7.5
0.6
D3
500
SL
39
±5%
DEA1X3F390JD3B
3150
6.0
6.0
7.5
0.6
D3
500
SL
47
±5%
DEA1X3F470JD3B
3150
7.0
6.0
7.5
0.6
D3
500
SL
56
±5%
DEA1X3F560JD3B
3150
7.0
6.0
7.5
0.6
D3
500
SL
68
±5%
DEA1X3F680JB3B
3150
8.0
6.0
7.5
0.6
B3
500
SL
82
±5%
DEA1X3F820JB3B
3150
8.0
6.0
7.5
0.6
B3
500
SL
100
±5%
DEA1X3F101JB3B
3150
9.0
6.0
7.5
0.6
B3
500
SL
120
±5%
DEA1X3F121JB3B
3150
10.0
6.0
7.5
0.6
B3
500
SL
150
±5%
DEA1X3F151JB3B
3150
11.0
6.0
7.5
0.6
B3
500
SL
180
±5%
DEA1X3F181JB3B
3150
11.0
6.0
7.5
0.6
B3
500
SL
220
±5%
DEA1X3F221JB3B
3150
12.0
6.0
7.5
0.6
B3
250
SL
270
±5%
DEA1X3F271JB3B
3150
14.0
6.0
7.5
0.6
B3
250
SL
330
±5%
DEA1X3F331JB3B
3150
15.0
6.0
7.5
0.6
B3
200
SL
390
±5%
DEA1X3F391JB3B
3150
16.0
6.0
7.5
0.6
B3
200
10 / 21
Reference only
Unit : mm
T.C.
Cap.
(pF)
Cap.
tol.
Customer Part Number
Murata Part Number
Dimension (mm)
DC
Rated volt.
(V)
D
T
F
d
P
Lead
code
Pack
qty.
(pcs)
SL
10
±5%
DEA1X3D100JP2A
2000
4.5
5.0
5.0
0.6 12.7
P2
1500
SL
12
±5%
DEA1X3D120JP2A
2000
4.5
5.0
5.0
0.6 12.7
P2
1500
SL
15
±5%
DEA1X3D150JP2A
2000
4.5
5.0
5.0
0.6 12.7
P2
1500
SL
18
±5%
DEA1X3D180JP2A
2000
4.5
5.0
5.0
0.6 12.7
P2
1500
SL
22
±5%
DEA1X3D220JP2A
2000
4.5
5.0
5.0
0.6 12.7
P2
1500
SL
27
±5%
DEA1X3D270JP2A
2000
4.5
5.0
5.0
0.6 12.7
P2
1500
SL
33
±5%
DEA1X3D330JP2A
2000
4.5
5.0
5.0
0.6 12.7
P2
1500
SL
39
±5%
DEA1X3D390JP2A
2000
5.0
5.0
5.0
0.6 12.7
P2
1500
SL
47
±5%
DEA1X3D470JN2A
2000
6.0
5.0
5.0
0.6 12.7
N2
1500
SL
56
±5%
DEA1X3D560JN2A
2000
6.0
5.0
5.0
0.6 12.7
N2
1500
SL
68
±5%
DEA1X3D680JN2A
2000
6.0
5.0
5.0
0.6 12.7
N2
1500
SL
82
±5%
DEA1X3D820JN2A
2000
7.0
5.0
5.0
0.6 12.7
N2
1500
SL
100
±5%
DEA1X3D101JN2A
2000
7.0
5.0
5.0
0.6 12.7
N2
1500
SL
120
±5%
DEA1X3D121JN2A
2000
8.0
5.0
5.0
0.6 12.7
N2
1500
SL
150
±5%
DEA1X3D151JN2A
2000
8.0
5.0
5.0
0.6 12.7
N2
1500
SL
180
±5%
DEA1X3D181JN2A
2000
9.0
5.0
5.0
0.6 12.7
N2
1500
SL
220
±5%
DEA1X3D221JN2A
2000
10.0
5.0
5.0
0.6 12.7
N2
1500
SL
270
±5%
DEA1X3D271JN2A
2000
11.0
5.0
5.0
0.6 12.7
N2
1500
SL
330
±5%
DEA1X3D331JN3A
2000
12.0
5.0
7.5
0.6 15.0
N3
900
SL
390
±5%
DEA1X3D391JN3A
2000
13.0
5.0
7.5
0.6 15.0
N3
900
SL
470
±5%
DEA1X3D471JN7A
2000
14.0
5.0
7.5
0.6 30.0
N7
500
SL
560
±5%
DEA1X3D561JN7A
2000
15.0
5.0
7.5
0.6 30.0
N7
500
SL
10
±5%
DEA1X3F100JP3A
3150
5.0
6.0
7.5
0.6 15.0
P3
900
SL
12
±5%
DEA1X3F120JP3A
3150
5.0
6.0
7.5
0.6 15.0
P3
900
SL
15
±5%
DEA1X3F150JP3A
3150
5.0
6.0
7.5
0.6 15.0
P3
900
SL
18
±5%
DEA1X3F180JP3A
3150
5.0
6.0
7.5
0.6 15.0
P3
900
SL
22
±5%
DEA1X3F220JP3A
3150
5.0
6.0
7.5
0.6 15.0
P3
900
11 / 21
Reference only
Unit : mm
T.C.
Cap.
(pF)
Cap.
tol.
Customer Part Number
Murata Part Number
Dimension (mm)
DC
Rated volt.
(V)
D
T
F
d
P
Lead
code
Pack
qty.
(pcs)
SL
27
±5%
DEA1X3F270JP3A
3150
6.0
6.0
7.5
0.6 15.0
P3
900
SL
33
±5%
DEA1X3F330JP3A
3150
6.0
6.0
7.5
0.6 15.0
P3
900
SL
39
±5%
DEA1X3F390JP3A
3150
6.0
6.0
7.5
0.6 15.0
P3
900
SL
47
±5%
DEA1X3F470JP3A
3150
7.0
6.0
7.5
0.6 15.0
P3
900
SL
56
±5%
DEA1X3F560JP3A
3150
7.0
6.0
7.5
0.6 15.0
P3
900
SL
68
±5%
DEA1X3F680JN3A
3150
8.0
6.0
7.5
0.6 15.0
N3
900
SL
82
±5%
DEA1X3F820JN3A
3150
8.0
6.0
7.5
0.6 15.0
N3
900
SL
100
±5%
DEA1X3F101JN3A
3150
9.0
6.0
7.5
0.6 15.0
N3
900
SL
120
±5%
DEA1X3F121JN3A
3150
10.0
6.0
7.5
0.6 15.0
N3
900
SL
150
±5%
DEA1X3F151JN3A
3150
11.0
6.0
7.5
0.6 15.0
N3
900
SL
180
±5%
DEA1X3F181JN3A
3150
11.0
6.0
7.5
0.6 15.0
N3
900
SL
220
±5%
DEA1X3F221JN3A
3150
12.0
6.0
7.5
0.6 15.0
N3
900
SL
270
±5%
DEA1X3F271JN7A
3150
14.0
6.0
7.5
0.6 30.0
N7
500
SL
330
±5%
DEA1X3F331JN7A
3150
15.0
6.0
7.5
0.6 30.0
N7
500
SL
390
±5%
DEA1X3F391JN7A
3150
16.0
6.0
7.5
0.6 30.0
N7
500
12 / 21
Reference only
5. Specification and test methods
No.
Item
1
Appearance and dimensions
2
3
4
Marking
Dielectric
strength
Between lead
wires
Body
insulation
No failure.
Between lead
wires
10 000MΩ min.
5
Insulation
Resistance (I.R.)
Capacitance
6
Q
7
Temperature characteristic
8
Strength of
lead
Specification
No marked defect on appearance
form and dimensions.
Please refer to [Part number list].
To be easily legible.
No failure.
Within specified tolerance.
Pull
400+20C*²min. (30pF under)
1 000 min.
(30pF min.)
+350 to -1 000ppm/°C
(Temp. range: +20 to +85°C)
Step
1
2
3
4
5
Temp.(°C)
20±2
-25±3
20±2
85±2
20±2
Lead wire should not cut off.
Capacitor should not be broken.
Bending
9
Vibration
resistance
Appearance
Capacitance
Q
10
Solderability of leads
Test method
The capacitor should be inspected by naked eyes
for visible evidence of defect.
Dimensions should be measured with slide calipers.
The capacitor should be inspected by naked eyes.
The capacitor should not be damaged when DC
voltage of 200% of the rated voltage are applied
between the lead wires for 1 to 5 s.
(Charge/Discharge current≤50mA.)
The capacitor is placed in the container with metal
balls of diameter 1mm so that each lead wire,
shortcircuited, is kept about 2mm
off the balls as shown
in the figure, and
AC1 250V (r.m.s.)
is applied for 1 to 5 s
About 2mm
between capacitor lead
Metal balls
wires and small metals.
(Charge/Discharge current≤50mA.)
The insulation resistance should be measured with
DC500±50V within 60±5 s of charging.
The capacitance should be measured at 20°C with
1±0.2MHz and AC5V(r.m.s.) max..
The Q should be measured at 20°C with 1±0.2MHz
and AC5V(r.m.s.) max..
The capacitance measurement should be made at
each step specified in Table.
No marked defect.
Within specified tolerance.
400+20C*²min. (30pF under)
1 000 min.
(30pF min.)
Lead wire should be soldered
with uniformly coated on the axial
direction over 3/4 of the
circumferential direction.
*² "C " expresses nominal capacitance value (pF)
ESDEA01A
13 / 21
As shown in the figure at right, fix the
body of the capacitor and apply a tensile
weight gradually to each lead wire in the
radial direction of the capacitor up to
10N ( 5N for lead diameter 0.5mm ),
and keep it for 10±1 s.
Each lead wire should be subjected to 5N ( 2.5N for
lead diameter 0.5mm ) of weight and bent 90° at the
point of egress, in one direction, then returned to its
original position, and bent 90° in the opposite
direction at the rate of one bend in 2 to 3 s.
The capacitor should be firmly soldered to the
supporting lead wire and vibrated at a frequency
range of 10 to 55Hz, 1.5mm in total amplitude, with
about a 1min rate of vibration change from 10Hz
to 55Hz and back to 10Hz. Apply for a total of 6 h;
2 h each in 3 mutually perpendicular directions.
The lead wire of a capacitor should be dipped into a
ethanol solution of 25wt% rosin and then into
molten solder for 2±0.5 s. In both cases the depth of
dipping is up to about 1.5 to 2mm from the root of
lead wires.
Temp. of solder :
245±5°C Lead Free Solder (Sn-3Ag-0.5Cu)
235±5°C H63 Eutectic Solder
Reference only
No.
11
12
13
14
15
Item
Soldering effect
Appearance
(Non-preheat)
Capacitance
change
Dielectric
strength
(Between lead
wires)
Specification
No marked defect.
Within ± 2.5%
Soldering effect
(On-preheat)
No marked defect.
Within ± 2.5%
Humidity
(Under steady
state)
Humidity loading
Life
Appearance
Capacitance
change
Dielectric
strength
(Between lead
wires)
Temperature
cycle
Per item 3.
Appearance
Capacitance
change
Q
No marked defect.
Within ± 5%
I.R.
Appearance
Capacitance
change
Q
1 000MΩ min.
No marked defect.
Within ± 5%
I.R.
Appearance
Capacitance
change
Q
I.R.
16
Per item 3.
Appearance
Capacitance
change
Q
I.R.
Dielectric
strength
(Between lead
wires)
275+5/2C*²min. (30pF under)
350 min.
(30pF min.)
275+5/2C*²min. (30pF under)
350 min.
(30pF min.)
1 000MΩ min.
No marked defect.
Within ± 3%
275+5/2C*²min. (30pF under)
350 min.
(30pF min.)
2 000MΩ min.
No marked defect.
Within ± 5%
275+5/2C*²min. (30pF under)
350 min.
(30pF min.)
1 000MΩ min.
Per item 3.
Test method
The lead wire should be immersed into the melted
solder of 350±10°C ( Body of φ5 and under:
270±5°C ) up to about 1.5 to 2.0mm from the
main body for 3.5±0.5 s. ( Body of φ5 and under:
5±0.5 s. )
Post-treatment :
Capacitor should be stored for 1 to 2 h at *¹room
condition.
First the capacitor should be stored at 120+0/-5°C
for 60+0/-5 s.
Then, as in figure, the lead wires should be
immersed solder of 260+0/-5°C up to 1.5 to 2.0mm
from the root of terminal for 7.5+0/-1 s.
Post-treatment :
Capacitor should be stored for 1 to 2 h at *¹room
condition.
Set the capacitor for 500 +24/-0 h at 40±2°C in 90
to 95% relative humidity.
Post-treatment :
Capacitor should be stored for 1 to 2 h at *¹room
condition.
Apply the rated voltage for 500 +24/-0 h at 40±2°C
in 90 to 95% relative humidity.
(Charge/Discharge current≤50mA.)
Post-treatment :
Capacitor should be stored for 1 to 2 h at *¹room
condition.
Apply a DC voltage of 150% of the rated voltage
for 1 000 +48/-0 h at 125±2°C, and relative humidity
of 50% max..
(Charge/Discharge current≤50mA.)
Post-treatment :
Capacitor should be stored for 1 to 2 h at *¹room
condition.
The capacitor should be subjected to 5 temperature
cycles.
Step Temperature(°C)
Time
1
30 min
-25±3
2
Room Temp.
3 min
3
30 min
+125±3
4
Room Temp.
3 min
Cycle time : 5 cycle
Post-treatment :
Capacitor should be stored for 1 to 2 h at *¹room
condition.
*¹ "room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
*² "C" expresses nominal capacitance value (pF)
ESDEA01A
14 / 21
Reference only
6.Packing specification
•Bulk type (Packing style code : B)
∗1
∗2
The number of packing = Packing quantity × n
The size of packing case and packing way
∗1 : Please refer to [Part number list].
∗2 : Standard n = 20 (bag)
Polyethylene bag
Partition
270 max.
125 max.
340 max.
Note)
The outer package and the number of
outer packing be changed by the order
getting amount.
Unit : mm
•Ammo pack taping type (Packing style code : A)
⋅ The tape with capacitors is packed zigzag into a case.
⋅ When body of the capacitor is piled on other body under it.
⋅ There should be 3 pitches and over without capacitors in leader and trailer.
The size of packing case and packing way
240 max.
Position of label
340 max.
60 max.
Capacitor
Hold down tape
Base tape
Hold down
tape upper
EKBCDE01
15 / 21
Unit : mm
Reference only
7. Taping specification
7-1. Dimension of capacitors on tape
Vertical crimp taping type < Lead code : N2 >
Pitch of component 12.7mm / Lead spacing 5.0mm
∗
Unit : mm
Item
Code
Dimensions
Remarks
Pitch of component
P
12.7±1.0
Pitch of sprocket hole
P0
12.7±0.3
Lead spacing
F
5.0± 0.2
Length from hole center to component center
P2
6.35±1.3
Length from hole center to lead
P1
3.85±0.7
Body diameter
D
Please refer to [Part number list ].
Deviation along tape, left or right
∆S
0±1.0
Carrier tape width
W
18.0±0.5
Position of sprocket hole
W1
9.0±0.5
H0
18.0± 2.0
0
Lead distance between reference and bottom
planes
0.8
Deviation of progress direction
They include deviation by lead bend .
Deviation of tape width direction
+0.5∼−1.0
Protrusion length
Diameter of sprocket hole
φD0
4.0±0.1
Lead diameter
φd
0.60±0.05
Total tape thickness
t1
0.6±0.3
Total thickness, tape and lead wire
t2
1.5 max.
Deviation across tape, front
∆h1
Deviation across tape, rear
∆h2
Portion to cut in case of defect
L
11.0± 1.0
Hold down tape width
W0
11.5 min.
Hold down tape position
W2
1.5±1.5
Coating extension on lead
e
Up to the end of crimp
Body thickness
T
Please refer to [Part number list ].
They include hold down tape thickness.
1.0 max.
0
ETP1N201A
16 / 21
Reference only
Vertical crimp taping type < Lead code : N3 >
Pitch of component 15.0mm / Lead spacing 7.5mm
∗
Unit : mm
Item
Code
Dimensions
Remarks
Pitch of component
P
15.0±2.0
Pitch of sprocket hole
P0
15.0±0.3
Lead spacing
F
7.5±1.0
Length from hole center to component center
P2
7.5±1.5
Length from hole center to lead
P1
3.75±1.0
Body diameter
D
Please refer to [ Part number list ].
Deviation along tape, left or right
∆S
0±2.0
Carrier tape width
W
18.0±0.5
Position of sprocket hole
W1
9.0±0.5
H0
18.0± 2.0
0
Lead distance between reference and bottom
planes
Deviation of progress direction
They include deviation by lead bend .
Deviation of tape width direction
+0.5∼−1.0
Protrusion length
Diameter of sprocket hole
φD0
4.0±0.1
Lead diameter
φd
0.60±0.05
Total tape thickness
t1
0.6±0.3
Total thickness, tape and lead wire
t2
1.5 max.
Deviation across tape, front
∆h1
Deviation across tape, rear
∆h2
Portion to cut in case of defect
L
11.0± 1.0
Hold down tape width
W0
11.5 min.
Hold down tape position
W2
1.5±1.5
Coating extension on lead
e
Up to the end of crimp
Body thickness
T
Please refer to [ Part number list ].
They include hold down tape thickness.
2.0 max.
0
ETP1N30101A
17 / 21
Reference only
Vertical crimp taping type < Lead code : N7 >
Pitch of component 30.0mm /Lead spacing 7.5mm
Unit : mm
Item
Code
Dimensions
Remarks
Pitch of component
P
30.0±2.0
Pitch of sprocket hole
P0
15.0±0.3
Lead spacing
F
7.5±1.0
Length from hole center to component center
P2
7.5±1.5
Length from hole center to lead
P1
3.75±1.0
Body diameter
D
Please refer to [ Part number list ].
Deviation along tape, left or right
∆S
0±2.0
Carrier tape width
W
18.0±0.5
Position of sprocket hole
W1
9.0±0.5
H0
18.0± 2.0
0
Lead distance between reference and bottom
planes
Deviation of progress direction
They include deviation by lead bend.
Deviation of tape width direction
+0.5∼−1.0
Protrusion length
Diameter of sprocket hole
φD0
4.0±0.1
Lead diameter
φd
0.60±0.05
Total tape thickness
t1
0.6±0.3
Total thickness, tape and lead wire
t2
1.5 max.
Deviation across tape, front
∆h1
Deviation across tape, rear
∆h2
Portion to cut in case of defect
L
11.0± 1.0
Hold down tape width
W0
11.5 min.
Hold down tape position
W2
1.5±1.5
Coating extension on lead
e
Up to the end of crimp
Body thickness
T
Please refer to [ Part number list ].
They include hold down tape thickness.
2.0 max.
0
ETP1N70101A
18 / 21
Reference only
Straight taping type < Lead code: P2 >
Pitch of component 12.7mm / Lead spacing 5.0mm
Unit : mm
Item
Code
Dimensions
Remarks
Pitch of component
P
12.7±1.0
Pitch of sprocket hole
P0
12.7±0.3
Lead spacing
F
5.0±0.2
Length from hole center to component center
P2
6.35±1.3
Length from hole center to lead
P1
3.85±0.7
Body diameter
D
Please refer to [ Part number list ].
Deviation along tape, left or right
∆S
0±1.0
Carrier tape width
W
18.0±0.5
Position of sprocket hole
W1
9.0±0.5
H
20.0±1.5
1.0
Lead distance between reference and bottom
planes
0.8
Deviation of progress direction
They include deviation by lead bend .
Deviation of tape width direction
+0.5∼−1.0
Protrusion length
Diameter of sprocket hole
φD0
4.0±0.1
Lead diameter
φd
0.60±0.05
Total tape thickness
t1
0.6±0.3
Total thickness, tape and lead wire
t2
1.5 max.
Deviation across tape, front
∆h1
Deviation across tape, rear
∆h2
Portion to cut in case of defect
L
11.0± 1.0
Hold down tape width
W0
11.5 min.
Hold down tape position
W2
1.5±1.5
Coating extension on lead
e
3.0 max.
Body thickness
T
Please refer to [ Part number list ].
They include hold down tape thickness.
1.0 max.
0
ETP1P20101A
19 / 21
Reference only
Straight taping type < Lead code : P3 >
Pitch of component 15.0mm / Lead spacing 7.5mm
Unit : mm
Item
Code
Dimensions
Remarks
Pitch of component
P
15.0±2.0
Pitch of sprocket hole
P0
15.0±0.3
Lead spacing
F
7.5±1.0
Length from hole center to component center
P2
7.5±1.5
Length from hole center to lead
P1
3.75±1.0
Body diameter
D
Please refer to [ Part number list ].
Deviation along tape, left or right
∆S
0±2.0
Carrier tape width
W
18.0±0.5
Position of sprocket hole
W1
9.0±0.5
H
20.0± 1.5
1.0
Lead distance between reference and bottom
planes
Deviation of progress direction
They include deviation by lead bend .
Deviation of tape width direction
+0.5∼−1.0
Protrusion length
Diameter of sprocket hole
φD0
4.0±0.1
Lead diameter
φd
0.60±0.05
Total tape thickness
t1
0.6±0.3
Total thickness, tape and lead wire
t2
1.5 max.
Deviation across tape, front
∆h1
Deviation across tape, rear
∆h2
Portion to cut in case of defect
L
11.0± 1.0
Hold down tape width
W0
11.5 min.
Hold down tape position
W2
1.5±1.5
Coating extension on lead
e
3.0 max.
Body thickness
T
Please refer to [ Part number list ].
They include hold down tape thickness.
2.0 max.
0
ETP1P30101A
20 / 21
Reference only
7-2. Splicing way of tape
1) Adhesive force of tape is over 3N at test condition as below.
W
Hold down tape
Base tape
2) Splicing of tape
a) When base tape is spliced
•Base tape should be spliced by cellophane tape.
(Total tape thickness should be less than 1.05mm.)
Progress direction
in production line
Hold down tape
Base tape
About 30 to 50
Cellophane tape
No lifting for the direction of
progressing
Unit : mm
b) When hold down tape is spliced
•Hold down tape should be spliced with overlapping.
(Total tape thickness should be less than 1.05mm.)
ape are spliced
•Base tape and adhesive tape should be spliced with splicing tape.
20 to 60
Hold down tape
Progress direction
in production line
Base tape
Unit : mm
c) When both tape are spliced
•Base tape and hold down tape should be spliced with splicing tape.
3 ) Missing components
•There should be no consecutive missing of more than three components.
•The number of missing components should be not more than 0.5% of
total components that should be present in a Ammo pack.
ETP2D03
21 / 21
Appendix
EU RoHS
This products of the following crresponds to EU RoHS.
RoHS
maximum concentration values tolerated by weight in homogeneous materials
・1000 ppm maximum Lead
・1000 ppm maximum Mercury
・100 ppm maximum Cadmium
・1000 ppm maximum Hexavalent chromium
・1000 ppm maximum Polybrominated biphenyls (PBB)
・1000 ppm maximum Polybrominated diphenyl ethers (PBDE)
工商网监
湘ICP备2023018690号
