Reference Specification
Safety Standard Certified Resin Molding SMD Type Ceramic Capacitors for
Consumer Electronics & Industrial Equipment /Type EA
Product specifications in this catalog are as of Nov. 2023, and are subject to change or
obsolescence without notice.
Please consult the approval sheet before ordering.Please read rating and Cautions first.
<Reference>Please kindly use our website.
Please refer to the product information page for more information on ceramic capacitors.→
Ceramic capacitor product information
Various data can be obtained directly from the product search.→ Product search (SMD) → Product search (Lead Type)
Reference only
CAUTION
1. OPERATING VOLTAGE
1. Do not apply a voltage to a safety standard certified product that exceeds the rated voltage as called out
in the specifications. Applied voltage between the terminals of a safety standard certified product shall be
less than or equal to the rated voltage (+10 %). When a safety standard certified product is used as a
DC voltage product, the AC rated voltage value becomes the DC rated voltage value.
(Example:AC250 V (r.m.s.) rated product can be used as DC250 V (+10 %) rated product.)
If both AC rated voltage and DC rated voltage are specified, apply the voltage lower than the respective
rated voltage.
1-1. When a safety standard certified product is used in a circuit connected to a commercial power supply,
ensure that the applied commercial power supply voltage including fluctuation should be less than 10 %
above its rated voltage.
1-2. When using a safety standard certified product as a DC rated product in circuits other than those
connected to a commercial power supply.
When AC voltage is superimposed on DC voltage, the zero-to-peak voltage shall not exceed the rated
DC voltage. When AC voltage or pulse voltage is applied, the peak-to-peak voltage shall not exceed the
rated DC voltage.
Typical Voltage Applied to the DC Capacitor
(E: Maximum possible applied voltage.)
2. Abnormal voltages (surge voltage, static electricity, pulse voltage, etc.) shall not exceed the rated DC
voltage.
2. OPERATING TEMPERATURE AND SELF-GENERATED HEAT
Keep the surface temperature of a capacitor below the upper limit of its rated operating temperature range.
Be sure to take into account the heat generated by the capacitor itself.
When the capacitor is used in a high-frequency current, pulse current or the like, it may have the selfgenerated heat due to dielectric-loss. Applied voltage should be the load such as self-generated heat is
within 20 ℃ on the condition of atmosphere temperature 25 ℃. When measuring, use a thermocouple of
small thermal capacity-K of Φ0.1 mm and be in the condition where capacitor is not affected by radiant
heat of other components and wind of surroundings. Excessive heat may lead to deterioration of the
capacitor’s characteristics and reliability. (Never attempt to perform measurement with the cooling fan
running. Otherwise, accurate measurement cannot be ensured.)
3.3.TEST
TESTCONDITION
CONDITIONFOR
FORWITHSTANDING
WITHSTANDINGVOLTAGE
VOLTAGE
1. TEST EQUIPMENT
Test equipment for AC withstanding voltage should be used with the performance of the wave similar
to 50/60 Hz sine wave.
If the distorted sine wave or over load exceeding the specified voltage value is applied, the defective
may be caused.
EGD30C
1/14
Reference only
2. VOLTAGE APPLIED METHOD
When the withstanding voltage is applied, capacitor’s lead or terminal should be firmly connected to the
out-put of the withstanding voltage test equipment, and then the voltage should be raised from near zero
to the test voltage.
If the test voltage without the raise from near zero voltage would be applied directly to capacitor, test
voltage should be applied with the *zero cross. At the end of the test time, the test voltage should be
reduced to near zero, and then capacitor’s lead or terminal should be taken off the out-put of the
withstanding voltage test equipment.
voltage sine wave
If the test voltage without the raise from near zero voltage would
be applied directly to capacitor, the surge voltage may arise,
0V
and therefore, the defective may be caused.
zero cross
*ZERO CROSS is the point where voltage sine wave pass 0 V.
- See the right figure 4. FAIL-SAFE
When capacitor would be broken, failure may result in a short circuit. Be sure to provide an appropriate
fail-safe function like a fuse on your product if failure would follow an electric shock, fire or fume.
5. VIBRATION AND IMPACT
Do not expose a capacitor or its leads to excessive shock or vibration during use.
6. SOLDERING
When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification of
the capacitor. Subjecting this product to excessive heating could melt the internal junction solder and
may result in thermal shocks that can crack the ceramic element.
When soldering capacitor with a soldering iron, it should be performed in following conditions.
6-1. Reflow Soldering
Soldering temperature : 230 to 260 ℃
Soldering time
: 10 to 30 s
Preheating temperature : 170 ℃ max.
[Standard Conditions for Reflow Soldering]
Temperature
(℃)
6-2. Flow Soldering
Soldering temperature : 260 ℃ max.
Soldering time
: 5 s max.
Preheating temperature : 120 ℃ max.
Preheating time
: 60 s max.
Soldering
260 ℃
230
170
150
130
Gradual
Cooling
℃
℃
℃
℃
Preheating
Time
6-3. Soldering Iron
Temperature of iron-tip : 400 ℃ max.
Soldering iron wattage : 50 W max.
Soldering time
: 3.5 s max.
60 - 120 s
EGD30C
2/14
10 - 30 s
Reference only
7. BONDING, RESIN MOLDING AND COATING
Before bonding, molding or coating this product, verify that these processes do not affect the quality of
capacitor by testing the performance of the bonded, molded or coated product in the intended
equipment.
In case of the amount of applications, dryness / hardening conditions of adhesives and molding resins
containing organic solvents (ethyl acetate, methyl ethyl ketone, toluene, etc.) are unsuitable, the outer
coating resin of a capacitor is damaged by the organic solvents and it may result, worst case, in a
short circuit.
The variation in thickness of adhesive, molding resin or coating may cause a outer coating resin
cracking and/or ceramic element cracking of a capacitor in a temperature cycling.
8. OPERATING AND STORAGE ENVIRONMENT
The molding resin of the molding type ceramic capacitor does not form a perfect seal, avoid corrosive gas
(e.g., hydrogen sulfide, sulfur dioxide, chlorine, ammonia gas etc.) and direct sunlight,
and use (storage) in the condition without moisture condensation.
When washing, bonding or molding this product, make sure that there is no effect on the quality in your
product. This one is MSL 3 product. So, in order to avoid the absorption of moisture, capacitors are
packed in moisture-proof package.
Under the following humidity and temperature conditions, the warranty period for unopened moisture-proof
package is 2 years after the moisture-proof package is enclosed.
Solder the enclosed capacitors within 168 h after opening the moisture-proof package.
Also, even after opening, store it in the packing condition at the time of delivery or in a similar state.
Temperature : 10 to 30 ℃
Humidity : 60 % max.
If it has been more than 1 week since opening, or if the 10 % display of the HIC (humidity indicator card)
is pink, perform baking (60 °C, 168 h) before mounting.
In addition, if it exceeds 12 months, check the solderability before use.
EGD30C
3/14
Reference only
9. LIMITATION OF APPLICATIONS
The products listed in the specification(hereinafter the product(s) is called as the “Product(s)”) are designed
and manufactured for applications specified in the specification. (hereinafter called as the “Specific
Application”)
We shall not warrant anything in connection with the Products including fitness, performance,
adequateness, safety, or quality, in the case of applications listed in from (1) to (11) written at the end of
this precautions, which may generally require high performance, function, quality, management of
production or safety.
Therefore, the Product shall be applied in compliance with the specific application.
WE DISCLAIM ANY LOSS AND DAMAGES ARISING FROM OR IN CONNECTION WITH THE
PRODUCTS INCLUDING BUT NOT LIMITED TO THE CASE SUCH LOSS AND DAMAGES CAUSED BY
THE UNEXPECTED ACCIDENT, IN EVENT THAT (i) THE PRODUCT IS APPLIED FOR THE PURPOSE
WHICH IS NOT SPECIFIED AS THE SPECIFIC APPLICATION FOR THE PRODUCT, AND/OR (ii) THE
PRODUCT IS APPLIED FOR ANY FOLLOWING APPLICATION PURPOSES FROM (1) TO (11) (EXCEPT
THAT SUCH APPLICATION PURPOSE IS UNAMBIGUOUSLY SPECIFIED AS SPECIFIC APPLICATION
FOR THE PRODUCT IN OUR CATALOG SPECIFICATION FORMS, DATASHEETS, OR OTHER
DOCUMENTS OFFICIALLY ISSUED BY US*)
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Aircraft equipment
Aerospace equipment
Undersea equipment
Power plant control equipment
Medical equipment
Transportation equipment
Traffic control equipment
Disaster prevention/security equipment
Industrial data-processing equipment
Combustion/explosion control equipment
Equipment with complexity and/or required reliability equivalent to the applications listed in the above.
For exploring information of the Products which will be compatible with the particular purpose other than
those specified in the specification, please contact our sales offices, distribution agents, or trading
companies with which you make a deal, or via our web contact form.
Contact form: https://www.murata.com/contactform
*We may design and manufacture particular Products for applications listed in (1) to (11). Provided that,
in such case we shall unambiguously specify such Specific Application in the specification without any
exception.
Therefore, any other documents and/or performances, whether exist or non-exist, shall not be deemed as
the evidence to imply that we accept the applications listed in (1) to (11).
EGD30C
4/14
Reference only
NOTICE
1. CLEANING (ULTRASONIC CLEANING)
To perform ultrasonic cleaning, observe the following conditions.
Rinse bath capacity : Output of 20 watts per liter or less.
Rinsing time : 5 min maximum.
Do not vibrate the PCB/PWB directly.
Excessive ultrasonic cleaning may lead to fatigue destruction of the terminals.
2. CAPACITANCE CHANGE OF CAPACITORS
• Class 1 capacitors
Capacitance might change a little depending on a surrounding temperature or an applied voltage.
Please contact us if you use for the strict time constant circuit.
• Class 2 capacitors
Class 2 capacitors like temperature characteristic B, E and F have an aging characteristic,
whereby the capacitor continually decreases its capacitance slightly if the capacitor leaves for a long
time. Moreover, capacitance might change greatly depending on a surrounding temperature or an
applied voltage. So, it is not likely to be able to use for the time constant circuit.
Please contact us if you need a detail information.
3. PERFORMANCE CHECK BY EQUIPMENT
Before using a capacitor, check that there is no problem in the equipment's performance and the
specifications.
Generally speaking, Class 2 ceramic capacitors have voltage dependence characteristics and
temperature dependence characteristics in capacitance. So, the capacitance value may change
depending on the operating condition in a equipment. Therefore, be sure to confirm the apparatus
performance of receiving influence in a capacitance value change of a capacitor, such as leakage
current and noise suppression characteristic.
Moreover, check the surge-proof ability of a capacitor in the equipment, if needed, because the surge
voltage may exceed specific value by the inductance of the circuit.
4. Land Dimensions
The recommandable land dimensions for reflow soldering are follows.
Regarding the "a" dimension, to ensure the creepage distance required by the safety standard
applys to your equipment.
Capacitor
Land
c
Dimension
8.0 6.0
b
a
8.0
b
2.2
c
3.6
a
Solder Resist
NOTE
1. Please make sure that your product has been evaluated in view of your specifications with our product
being mounted to your product.
2. You are requested not to use our product deviating from this specification.
EGD30C
5/14
Reference only
1.Application
This product specification is applied to Safety Standard Certified Resin Molding SMD Type
Ceramic Capacitors Type EA.
The safety standard certification is obtained as Class X1, Y1.
1.Specific applications:
・Consumer Equipment: Products that can be used in consumer equipment such as home appliances,
audio/visual equipment, communication equipment, information equipment, office equipment, and
household robotics, and whose functions are not directly related to the protection of human life
and property.
・Industrial Equipment: Products that can be used in industrial equipment such as base stations,
manufacturing equipment, industrial robotics equipment, and measurement equipment, and whose
functions do not directly relate to the protection of human life and property.
・Medial Equipment [GHTF A/B/C] except for Implant Equipment: Products suitable for use in medical
devices designated under the GHTF international classifications as Class A or Class B (the functions of
which are not directly involved in protection of human life or property) or in medical devices other than
implants designated under the GHTF international classifications as Class C (the malfunctioning of which is
considered to pose a comparatively high risk to the human body).
・Automotive infotainment/comfort equipment: Products that can be used for automotive equipment such as
car navigation systems and car audio systems that do not directly relate to human life and whose structure,
equipment, and performance are not specifically required by law to meet technical standards for safety
assurance or environmental protection.
2.Unsuitable Application: Applications listed in “Limitation of applications” in this product specification.
Approval standard and certified number
Standard number
UL/cUL UL60384-14/CSA E60384-14
*Certified number
Rated voltage
X1: AC440 V(r.m.s.) / DC1,500 V
Y1: AC300 V(r.m.s.) / DC1,500 V
E37921
ENEC
EN60384-14
SE-ENEC-2300151
X1: AC440 V(r.m.s.)
(SEMKO)
Y1: AC300 V(r.m.s.)
CQC
IEC60384-14
CQC16001142384
*Above Certified number may be changed on account of the revision of standards and
the renewal of certification.
2.Rating
2-1.Operating temperature range
-40 ~ 125°C
2-2.Rated Voltage
X1: AC440 V(r.m.s.)
Y1: AC300 V(r.m.s.)
DC1,500 V
2-3.Part number configuration
ex.)
DK1
Series
F3
Temperature
Characteristics
EA
222
M
86
R
BH01
Certified
Type
Capacitance
Capacitance
Tolerance
Body
Package
Individual
Dimension
• Series
DK1 denotes resin molding SMD type safety standard recognized ceramic capacitor
of class Y1.
TEIKAKU
6/14
Specification
Reference only
• Temperature Characteristics
Please confirm detailed specification on [Specification and test methods].
Code
Temperature Characteristics
1X
SL
B3
B
E3
E
F3
F
• Certified Type
This denotes safety certified type name Type EA.
• Capacitance
The first two digits denote significant figures ; the last digit denotes the multiplier of 10 in pF.
ex.) In case of 222 .
22 × 102 = 2200 pF
• Capacitance Tolerance
Please refer to [ Part number list ].
• Body Dimension
Code
86
• Package
Code
H
R
Body Dimension
8.0 × 6.0 mm
Package
Φ180 mm Reel type
Φ330 mm Reel type
• Individual Specification
Murata’s control code
Please refer to Part number list .
3.Marking
Certified type
Capacitance
Rated Voltage
Company name code
Manufacturing year
Manufacturing month
: EA
: Actual value(under 100 pF)
3 digit system(100 pF and over)
: X1 440~
Y1 300~
15 (タイ製)
(Made in Thailand)
:
: Letter code ( The last digit of A.D. year.)
: Code
ex.)
YEAR
MONTH
2022
11(November)
2N *
*From January to September : “1” to “9”,
October : “O” , November : “N” , December : “D”
(Example)
TEIKAKU
7/14
EA 222
X1 440~
Y1 300~
15 2N
Reference only
4. Part number list
Unit : mm
Customer
Part Number
Murata
Part Number
T.C.
Cap.
(pF)
DK11XEA100K86HBH01
SL
10
DK11XEA220K86HBH01
SL
22
Cap.
tol.
Dimension (mm)
Body
Dimension
Pack
qty.
(pcs)
L
W
T
max.
±10%
11.4±0.5
6.0±0.5
2.5
86
500
±10%
11.4±0.5
6.0±0.5
2.5
86
500
DK11XEA470K86HBH01
SL
47
±10%
11.4±0.5
6.0±0.5
2.5
86
500
DK1B3EA101K86HBH01
B
100
±10%
11.4±0.5
6.0±0.5
2.5
86
500
DK1B3EA221K86HBH01
B
220
±10%
11.4±0.5
6.0±0.5
2.5
86
500
DK1B3EA331K86HBH01
B
330
±10%
11.4±0.5
6.0±0.5
2.5
86
500
DK1B3EA471K86HBH01
B
470
±10%
11.4±0.5
6.0±0.5
2.5
86
500
DK1B3EA681K86HBH01
B
680
±10%
11.4±0.5
6.0±0.5
2.5
86
500
DK1E3EA102M86HBH01
E
1000
±20%
11.4±0.5
6.0±0.5
2.5
86
500
DK1E3EA152M86HBH01
E
1500
±20%
11.4±0.5
6.0±0.5
2.5
86
500
DK1F3EA222M86HBH01
F
2200
±20%
11.4±0.5
6.0±0.5
2.5
86
500
DK11XEA100K86RBH01
SL
10
±10%
11.4±0.5
6.0±0.5
2.5
86
2500
DK11XEA220K86RBH01
SL
22
±10%
11.4±0.5
6.0±0.5
2.5
86
2500
DK11XEA470K86RBH01
SL
47
±10%
11.4±0.5
6.0±0.5
2.5
86
2500
DK1B3EA101K86RBH01
B
100
±10%
11.4±0.5
6.0±0.5
2.5
86
2500
DK1B3EA221K86RBH01
B
220
±10%
11.4±0.5
6.0±0.5
2.5
86
2500
DK1B3EA331K86RBH01
B
330
±10%
11.4±0.5
6.0±0.5
2.5
86
2500
DK1B3EA471K86RBH01
B
470
±10%
11.4±0.5
6.0±0.5
2.5
86
2500
DK1B3EA681K86RBH01
B
680
±10%
11.4±0.5
6.0±0.5
2.5
86
2500
DK1E3EA102M86RBH01
E
1000
±20%
11.4±0.5
6.0±0.5
2.5
86
2500
DK1E3EA152M86RBH01
E
1500
±20%
11.4±0.5
6.0±0.5
2.5
86
2500
DK1F3EA222M86RBH01
F
2200
±20%
11.4±0.5
6.0±0.5
2.5
86
2500
PNLIST
8/14
Reference only
5. Specification
No.
Test Item
Test Method (Ref. Standard:JIS C 5101(all parts), IEC60384(all parts))
Specification
1
Operating Temperature
-40 to 125 °C
2
Appearance
No defects or abnormalities
Visual inspection.
3
Dimensions
Within the specified dimension.
Using calipers and micrometers.
4
Dielectric
strength
No defects or abnormalities.
The capacitor shall not be damage when AC4,000 V(r.m.s.) and
DC6,000 V is applied between the terminations for 60 s.
Terminal To
No defects or abnormalities.
External Resin
The capacitor shall not be damage when AC4,000 V(r.m.s.) and
DC6,000 V is applied between the terminations for 60 s.
Between
Terminals
5
Insulation Resistance (I.R.)
6,000 MΩ or more.
The insulation resistance shall be measured with DC500±50 V within 60
±5 s of charging.
The voltage should be applied to the capacitor through a resistor of 1 M
Ω.
6
Capacitance
Within the specified tolerance.
7
Dissipation Factor (D.F.)
SL,B,E : DF≦0.025
F
: DF≦0.05
Capacitance/D.F. shall be measured at 20 °C with the frequency
of 1±0.2 kHz and a voltage of AC1±0.2 V(r.m.s.).
8
Capacitance Temperature
characteristic
Temp. Coefficient
SL: +350 to -1000 ppm/°C
(Temp. Range: 20 to 85°C)
Cap. Change
B:within ±10 %
E:within +20/-55 %
F:within +30/-80 %
(Temp. Range:-25 to 85 °C)
9
Vibration
resistance
Appearance
No marked defect.
Capacitance
Within the specified tolerance.
Dissipation
Factor (D.F.)
Pass the item No.7.
The capacitance measurement shall be made at each step in table.
•Pretreatment for B, E, F char.
Perform the heat treatment at 150+0/-10 °C for 60±5 min and then let
sit for 24±2 h at *room condition.
Step
1
2
3
4
5
Temp.(°C)
20±2
-25±2
20±2
85±2
20±2
Solder the capacitor to the Test Jig A (glass epoxy board) shown in
"Complement of test method".
The capacitor shall be subjected to a simple harmonic motion having a
total amplitude of 1.5mm, the frequency being varied uniformly between
the approximate limits of 10 and 55 Hz.
The frequency range, from 10 to 55 Hz and return to 10Hz, shall be
traversed in approximately 1 min.
This motion shall be applied for a period of 2 h in each of 3 mutually
perpendicular directions (total of 6 h).
10 Solderability of termination
75 % of the terminations are to be
soldered .
Immerse the capacitor in the solution of rosin ethanol (25% rosin in
weight propotion).
Immerse in solder solution for 2±0.5 s.
Temp. of solder : 245±5 °C
11 Soldering
effect
(Reflow)
Appearance
No marked defects.
Capacitance
change
Within ±10 %
I.R.
1,000 MΩ or more.
Dielectric
strength
Pass the item No.4.
Preheat the capacitor at 150 to 180 °C for 90±30 s.
Reflow temp. : 230 °C min. (Max. temp. : 260 °C)
Reflow time : 30±10 s.
Reflow number of times : 4 times
Let sit at *room condition for 24±2 h, then measure.
• The next reflow porcess should be done after the temperature of the
sample has dropped to room temperature.
• Pretreatment for B, E, F char.
Capacitor should be stored at 150+0/-10 °C for 1 h, and apply the
AC4,000 V(r.m.s.) 60 s then placed at *room condition for 24±2 h
before initial measurements.
12 Adhesive strength of
termination
No removal of the terminations or
other defects should occur.
Solder the capacitor to the Test Jig A (glass epoxy board) shown in
“Complement of Test method”.
Then apply 10 N force in the direction of the arrow.
10 N, 10±1 s
Glass Epoxy Board
* "room condition" Temperature : 15 to 35 °C, Relative humidity : 45 to 75 %, Atmospheric pressure : 86 to 106 kPa
ESEA01E
9/14
Reference only
No.
Test Item
13 Temperature
cycle
Test Method (Ref. Standard:JIS C 5101(all parts), IEC60384(all parts))
Specification
Appearance
No marked defect.
Capacitance
change
Within ±15 %
Dissipation
Factor (D.F.)
SL : DF≦0.025
B,E : DF≦0.05
F : DF≦0.075
I.R.
3,000 MΩ or more
Dielectric
strength
Pass the item No.4.
Fix the capacitor to the supporting Test Jig A (glass epoxy board)
shown in "Complement of test method".
Perform the 5 cycles according to the 4 heat treatments listed the
following table.
Step
Temp.(℃)
1
-40±3
Time(min.)
30±3
2
Room Temp.
2 to 3
3
125±3
30±3
4
Room Temp.
2 to 3
Let sit at *room condition for 24±2 h, then measure.
• Pretreatment for B, E, F char.
Capacitor should be stored at 150+0/-10 °C for 1 h, and apply the
AC4,000 V(r.m.s.) 60 s then placed at *room condition for 24±2 h
before initial measurements.
14 Humidity
(Steady
state)
15-1 Humidity
loading (AC)
15-2 Humidity
loading (DC)
Appearance
No marked defect.
Capacitance
change
Within ±20 %
Dissipation
Factor (D.F.)
SL : DF≦0.025
B,E : DF≦0.05
F : DF≦0.075
I.R.
3,000 MΩ or more
Dielectric
strength
Pass the item No.4.
Appearance
No marked defect.
Capacitance
change
Within ±20 %
Dissipation
Factor (D.F.)
SL : DF≦0.025
B,E : DF≦0.05
F : DF≦0.075
I.R.
3,000 MΩ or more
Dielectric
strength
Pass the item No.4.
Appearance
No marked defect.
Capacitance
change
Within ±20 %
Dissipation
Factor (D.F.)
SL : DF≦0.025
B,E : DF≦0.05
F : DF≦0.075
I.R.
3,000 MΩ or more
Dielectric
strength
Pass the item No.4.
Sit the capacitor at 40±2 °C and relative humidity 90 to 95 % for
500+24/-0 h.
Remove and let sit for 24±2 h at *room condition, then measure.
• Pretreatment for B, E, F char.
Capacitor should be stored at 150+0/-10 °C for 1 h, and apply the
AC4,000 V(r.m.s.) 60 s then placed at *room condition for 24±2 h
before initial measurements.
Apply the rated voltage AC440 V(r.m.s.) at 40±2 °C and relative
humidity
90 to 95% for 500+24/-0 h.
Remove and let sit for 24±2 h at *room condition, then measure.
• Pretreatment for B, E, F char.
Capacitor should be stored at 150+0/-10 °C for 1 h, and apply the
AC4,000 V(r.m.s.) 60 s then placed at *room condition for 24±2 h
before initial measurements.
Apply the rated voltage DC1,500 V(r.m.s.) at 40±2 °C and relative
humidity
90 to 95% for 500+24/-0 h.
Remove and let sit for 24±2 h at *room condition, then measure.
• Pretreatment for B, E, F char.
Capacitor should be stored at 150+0/-10 °C for 1 h, and apply the
AC4,000 V(r.m.s.) 60 s then placed at *room condition for 24±2 h
before initial measurements.
* "room condition" Temperature : 15 to 35 °C, Relative humidity : 45 to 75 %, Atmospheric pressure : 86 to 106 kPa
ESEA01E
10/14
Reference only
No.
16-1 Life (AC)
Test Item
Test Method (Ref. Standard:JIS C 5101(all parts), IEC60384(all parts))
Specification
Appearance
No marked defect.
Capacitance
change
Within ±20 %
I.R.
3,000 MΩ or more
Dielectric
strength
Pass the item No.4.
Impulse Voltage test is performed.
Each individual capacitor shall be subjected to a 8 kV Impulse (the
voltage value means zero to peak) for 3 times or more.
Then the capacitors are applied to life test.
Front time (T1) = 1.7 μs=1.67T
Time to half-value (T2) = 50 μs
Apply voltage as Table for 1,000 h at 125+2/-0 °C, relative humidity 50
% max.
Applied voltage
AC550 V(r.m.s.) except that once each hour the voltage is
increased to AC1,000 V(r.m.s.) for 0.1 s.
Remove and let sit for 24±2 h at *room condition, then measure.
• Pretreatment for B, E, F char.
Capacitor should be stored at 150+0/-10 °C for 1 h, and apply the
AC4,000 V(r.m.s.) 60 s then placed at *room condition for 24±2 h
before initial measurements.
16-2 Life (DC)
Appearance
No marked defect.
Capacitance
change
Within ±20 %
I.R.
3,000 MΩ or more
Dielectric
strength
Pass the item No.4.
Impulse Voltage test is performed.
Each individual capacitor shall be subjected to a 8 kV Impulse (the
voltage value means zero to peak) for 3 times or more.
Then the capacitors are applied to life test.
Front time (T1) = 1.7 μs=1.67T
Time to half-value (T2) = 50 μs
Apply DC2,550 V for 1,000 h at 125+2/-0 °C, relative humidity 50 %
max.
Remove and let sit for 24±2 h at *room condition, then measure.
• Pretreatment for B, E, F char.
Capacitor should be stored at 150+0/-10 °C for 1 h, and apply the
AC4,000 V(r.m.s.) 60 s then placed at *room condition for 24±2 h
before initial measurements.
17 Passive flammability
The burning time should not be
exceeded the time 30 s.
The capacitor under test shall be held in the flame in the position which
best promotes burning. Each specimen shall only be
exposed once to the flame. Time of exposure to flame : 30 s.
The tissue paper should not ignite.
Length of flame : 12±1 mm
Gas burner
: Length 35 mm min.
Inside dia : 0.5±0.1 mm
Outside dia : 0.9 mm max.
Gas
: Butane gas purity 95 % min.
Test specimen
Approximately 8mm
flame
burner
200±5㎜
45°
Tissue paper
Wood board of approximately 10mm in thickness
* "room condition" Temperature : 15 to 35 °C, Relative humidity : 45 to 75 %, Atmospheric pressure : 86 to 106 kPa
ESEA01E
11/14
Reference only
No.
Test Item
18 Active flammability
Test Method (Ref. Standard:JIS C 5101(all parts), IEC60384(all parts))
Specification
The cheese-cloth should not be
on fire.
The capacitor shall be individually wrapped in at least one but more
than two complete layers of cheesecloth.
The capacitor shall be subjected to 20 discharges.
The interval between successive discharges shall be 5 s.
The UAc shall be maintained for 2 min after the last discharge.
C1,2
L1 to L4
R
UAc
F
Cx
Ut
ESEA01E
12/14
: 1 μF±10 %,
C3 : 0.033 μF±5 % 10 kV
: 1.5 mH±20 % 16A Rod core choke
: 100 Ω±2 %,
Ct : 3 μF±5 % 10 kV
: UR ±5 %
UR : Rated voltage
: Fuse, Rated 16 A
: Capacitor specimens
: Voltage impressed on the tank capacitor Ct
Reference only
6. Complement of Test Method
6.1.Test Jig
The test jig should be Jig A as described in “Specifications and Test methods”.
The specimen should be soldered by the conditions as described below.
Soldering Method : Reflow soldering
Solder : Sn-3.0Ag-0.5Cu
(1) Test Jig A
Solder resist
1.0
19.4
8.0
7.4
2.2
0.5
5.4
3.6
2.0
9.4
Copper foil
•Material : Glass Epoxy Board
•Thickness : 1.6 mm
•Thickness of copper foil : 0.035 mm
ESEA01E
13/14
Reference only
7. Packing
7-1. Dimension of tape
2.0+/-0.1
4.0+/-0.1
1.5+0.1/-0
0.4+/-0.1
8.0+/-0.1
1.75+/-0.1
11.5+/-0.1
B
24+/-0.3
A
A×B=12.0×7.0 (typ.)
4.0 max.
(Unit : mm)
7-2. Dimension of Reel
W1
E
A
B
D
C
W
(Unit : mm)
Reel
A
B
C
D
E
W
W1
Φ180mm Reel
180+0/-3.0
60 min.
13.0±0.2
21.0±0.8
2.0±0.5
30.9 max.
26.5 max.
Φ330mm Reel
330±2.0
60 min.
13.0±0.2
21.0±0.8
2.0±0.5
30.4 max.
26.4 max.
(1) Part of the leader and part of the empty tape shall be attached to the end of the tape as follows.
Vacant section : 160 min.
Capacitor mounting
Vacant section
210 min.
190 min.
Direction of feed
(Unit : mm)
(2) The top tape or cover tape and base tape are not attached at the end of the tape for a minimum of 2 pitches.
(3) Missing capacitors number within 0.1 % of the number per reel or 1 pc, whichever is greater, and not
continuous.
(4) The top tape or cover tape and bottom tape shall not protrude beyond the edges of the tape
and shall not cover sprocket holes.
(5) Cumulative tolerance of sprocket holes, 10 pitches : ±0.3 mm.
(6) Peeling off force : 0.1 to 0.6 N in the direction shown on the follows.
165 to 180 °
Top Tape or Cover Tape
Base Tape
EKBCDK01A
14/14