SpecNo.JEFL243C-0005S-01
Reference Only
P 1/9
Chip Common Mode Choke Coil
DLW21HN□□□SQ2□
Reference Specification
1. Scope
This reference specification applies to Chip Common Mode Choke Coil DLW21H Series.
2. Part Numbering
(ex.)
DL W
21 H N
(1)
(2) (3) (4) (5)
(1) Chip Common Mode Choke Coil
(2) Structure (W : Winding Type)
(3) Dimension (LW)
(4) Type
(5) Category
670
(6)
S Q
2 L
(7) (8) (9) (10)
(6) Impedance (Typ. at 100MHz)
(7) Circuit
(8) Features
(9) Number of Line
(10) Packaging Code L : Taping / B : Bulk
3. Rating
Customer
Part Number
Insulation
DC
Common Mode Impedance Rated Withstanding Rated
Current Resistance Resistance
Voltage
Voltage
(at 100MHz, Under
( max.) (Mmin.)
(mA)
V(DC)
Standard Testing Condition) V(DC)
( )
Murata
Part Number
DLW21HN181SQ2L
DLW21HN181SQ2B
DLW21HN121SQ2L
DLW21HN121SQ2B
DLW21HN900SQ2L
DLW21HN900SQ2B
DLW21HN670SQ2L
DLW21HN670SQ2B
180 ± 25 %
250
0.50
280
0.45
90 ± 25 %
330
0.35
67 ± 25 %
330
0.35
120 ± 25 %
50
Operating Temperature : -40 to +85°C
Storage Temperature
4. Standard Testing Condition
125
10
: -40 to +85°C
Temperature : 20 ± 2°C
Humidity : 60 to 70%(RH)
Atmospheric Pressure : 86 to106kPa
Temperature : Ordinary Temperature 15 to 35°C
Humidity : Ordinary Humidity 25 to 85%(RH)
5. Style and Dimensions
0 .9 ±0 .1
)
7
1
.
0
(
■ Equivalent Circuits
1.2±0.2
2.0±0.2
(0.45)
(1)
(2)
(0.4)
(0.45)
:Electrode
(1)
(2)
(4)
(3)
No polarity
(0.4)
() : Reference Value
(4)
■ Unit Mass (Typical value)
(in mm)
(3)
0.009g
6. Marking
No Marking.
7. Electrical Performance
No.
7.1
Item
Common Mode
Impedance
(Zc)
Specification
Meet item 3.
Test Method
Measuring Equipment : Agilent 4291A or the
equivalent
Measuring Frequency : 100±1MHz(ref.item 10,11)
MURATA MFG.CO.,LTD
SpecNo.JEFL243C-0005S-01
Reference Only
No.
7.2
Item
Withstanding
Voltage
Specification
Products shall not be
damaged.
7.3
DC Resistance
(Rdc)
Meet item 3.
7.4
Insulation
Resistance (I.R.)
P 2/9
Test Method
Test Voltage : 2.5 times for Rated Voltage
Time : 5±1 s
Charge Current : 1 mA max. (ref.item 10)
Measuring current : 100mA max. (ref.item 10)
(In case of doubt in the above mentioned standard
condition, measure by 4 terminal method.)
Measuring voltage : Rated Voltage
Measuring time : 1 minute max. (ref.item 10)
8. Mechanical Performance
No.
8.1
8.2
Item
Appearance and
Dimensions
Bonding Strength
Specification
Meet item 5.
No evidence of coming off
substrate.
Products shall not be
mechanical damaged.
Test Method
Visual Inspection and measured with Slide Calipers
or Micrometer.
It shall be soldered on the substrate.
Applying Force(F) : 5N
Applying Time : 5±1seconds
Pressure
Substrate
Product
Test board fixture
8.3
Bending Strength
Meet Table 1.
Table 1
Appearance
No damaged
It shall be soldered on the Glass-epoxy substrate.
Deflection : 2mm
(t=1.0mm).
Keeping time : 5 seconds
Speed of Applying Force : 0.5mm/s
Pressure jig
Common Mode
Impedance
R230
within ±20%
F
Change
I.R.
Withstanding
Voltage
Deflection
10MΩ min.
45
No damaged
8.4
Drop
8.5
Vibration
8.6
Solderability
The electrodes shall be at least
90% covered with new solder
coating.
8.7
Resistance to
Soldering Heat
Meet Table 1.
45
Product
It shall be dropped on concrete or steel board.
Method : free fall
Height : 1 m
The Number of Times : 3 times
It shall be soldered on the substrate.
Oscillation Frequency : 10 to 55 to 10Hz for 1 minute
Total Amplitude : 1.5mm
Testing Time : A period of 2 hours in each of 3
mutually perpendicular directions. (Total 6 hours)
Flux:Ethanol solution of rosin,25(wt)% includes
activator equivalent to 0.06 to 0.10(wt)% chlorine
Pre-Heating : 80 to 120°C 1minute
Solder : Sn-3.0Ag-0.5Cu
Solder Temperature : 245±3°C
Immersion Time : 4±1 seconds
Immersion and emersion rates : 25mm/s
Flux : Ethanol solution of rosin,25(wt)% includes
activator equipment to 0.06 to 0.10(wt)% chlorine
Pre-Heating : 80 to 120°C, 1minute
Solder : Sn-3.0Ag-0.5Cu
Solder Temperature : 260±5°C
Immersion Time : 5±0.5 seconds
Immersion and emersion rates : 25mm/s
Then measured after exposure in the room
condition for 4 to 48 hours.
MURATA MFG.CO.,LTD
Reference Only
SpecNo.JEFL243C-0005S-01
9. Environmental Performance(Products shall be soldered on the substrate.)
No.
9.1
Item
Temperature
Cycle
9.2
Humidity
9.3
Heat life
9.4
Cold Resistance
Specification
Meet Table 1.
P 3/9
Test Method
1 Cycle
Step 1 -40°C(+0°C,-3°C) / 30±3 min
Step 2 Ordinary Temp. / 10 to 15 minutes
Step 3 +85°C(+3°C,-0°C) / 30±3 min
Step 4 Ordinary Temp. / 10 to 15 minutes
Total of 10 cycles
Then measured after exposure in the
room condition for 4 to 48 hours
Temperature : 40±2°C
Humidity : 90~95%(RH)
Time : 1000(+48 hours,-0 hours)
Then measured after exposure in the
room condition for 4 to 48 hours.
Temperature : 85±2°C
Applying Voltage : 2times for Rated Voltage
Time : 1000(+48 hours,-0 hours)
Then measured after exposure in the
room condition for 4 to 48 hours. (ref.item 10)
Temperature : -40± 2°C
Time : 1000(+48 hours,-0 hours)
Then measured after exposure in the
room condition for 4 to 48 hours.
10. Terminal to be Tested.
When measuring and suppling the voltage,the following terminal is applied.
No.
Item
Terminal to be Tested
10.1
Common Mode Impedance
Terminal
(Measurement Terminal)
10.2
Withstanding Voltage
(Measurement Terminal)
Terminal
Terminal
Terminal
10.3
10.4
10.5
DC Resistance
(Measurement Terminal)
Insulation Resistance
(Measurement Terminal)
Heat Life(Supply Terminal)
Terminal
Terminal
Terminal
Terminal
Terminal
Terminal
11. Measuring method for common mode impedance.
Measured common mode impedance may be included measurement error due to stray capacitance,
residual inductance of test fixture.
To correct this error, the common mode impedance should be calculate as follows;
(1) Measure admittance of the fixture(opened), Go Bo.
(2) Measure impedance of the fixture(shorted), Rs Xs.
(3) Measure admittance of the specimen, Gm Bm.
(4) Calculate corrected impedance Z using the formula below.
Z = (Rx2+Xx2) 1/2
Where
Gm-Go
Rx = (Gm-Go)2 + (Bm-Bo)2 - Rs
-(Bm- Bo)
Xx = (Gm-Go) 2 + (Bm-Bo)2 - Xs
MURATA MFG.CO.,LTD
SpecNo.JEFL243C-0005S-01
Reference Only
P 4/9
12. P.C.B., Flux, Solder and Soldering condition
Test shall be done using P.C.B., Flux, Solder and Soldering condition which are
specified in item 16 except the case of being specified special condition.
13. Impedance Frequency Characteristics(Typical)
10000
Common Mode
DLW21HN181SQ2
1000
DLW21HN121SQ2
l Z l (Ω)
DLW21HN900SQ2
100
DLW21HN670SQ2
10
DLW21HN181SQ2
DLW21HN121SQ2
1
DLW21HN900SQ2
DLW21HN670SQ2
Differential Mode
0.1
1
10
100
1000
Sprocket Hole
1.5± 0.1
0
4.0±0.1
2.0±0.05
0.25±0.05
*Dimension of the Cavity is measured
2.3±0.1
3.5±0.05
8.0±0.3
1.75±0.1
f (MHz)
14. Specification of Packaging
14.1 Appearance and Dimensions ( 8mm-wide,Plastic tape)
at the bottom side.
1.1±0.1
1.55±0.1
4.0±0.1
Cavity
Direction of feed
(in mm)
14.2 Specification of Taping
(1)Packing quantity(Standard quantity) 3000 pcs. / reel
(2)Packing Method
Products shall be packaged in each embossed cavity of plastic tape and sealed with cover tape.
(3) Spliced point
The cover tape have no spliced point.
(4) Sprocket Hole
Sprocket hole shall be located on the left hand side toward the direction of feed.
(5)Missing components number
Missing components number within 0.1% of the number per reel or 1 pc., whichever is greater,and are not
continuous.The specified quantity per reel is kept.
14.3 Pull Strength of Plastic Tape
Plastic Tape
Cover Tape
5N min.
10N min.
14.4 Peeling off force of Cover Tape
0.2 to 0.7N(Minimum value is Typical)
Speed of Peeling off : 300 mm / min
165 to 180 degree
F
Cover tape
Plastic tape
MURATA MFG.CO.,LTD
Reference Only
SpecNo.JEFL243C-0005S-01
14.5 Dimensions of Leader-tape, Trailer and Reel
Leader
Trailer
2.0±0.5
P 5/9
160 min.
190 min.
210 min.
Empty tape
Top tape
Label
13.0±0.2
1
60± 0
21.0±0.8
9± 10
Direction of feed
13±1.4
0
180± 3
14.6 Marking for reel
Customer part number, MURATA part number, Inspection number(1), RoHS discrimination(2), Quantity, etc
1) « Expression of Inspection No. »
□□ OOOO
(1) Factory Code
(2) Date
(3) Serial No.
(1)
(2)
(3)
First digit
: Year / Last digit of year
Second digit
: Month / Jan. to Sep. 1 to 9, Oct. to Dec. O,N,D
Third, Fourth digit : Day
2) « Expression of RoHS discrimination »
ROHS – Y (△)
(1) RoHS regulation conformity parts.
(2) MURATA classification number
(1) (2)
14.7 Marking for Outside package
Customer name Purchasing Order Number, Customer Part Number, MURATA part number,
RoHS discrimination(2), Quantity, etc
14.8 Specification of Outer Case
Outer Case Dimensions
Standard Reel Quantity in Outer Case
(mm)
(Reel)
W
D
H
186
186
93
5
Above Outer Case size is typical. It depends on a quantity of an
order.
Label
H
D
W
15.
!
△
Caution
15.1 Mounting Direction
Mount products in right direction.
Wrong direction which is 90°rotated from right direction causes not only open or short circuit but also
flames or other serious trouble.
Z
right direction
Z
wrong direction
15.2 Limitation of Applications
Please contact us before using our products for the applications listed below which require especially
high reliability for the prevention of defects which might directly cause damage to the third party's life, body
or property.
(1) Aircraft equipment
(2) Aerospace equipment
(3) Undersea equipment
(4) Power plant control equipment
(5) Medical equipment
(6) Transportation equipment (vehicles, trains, ships, etc.)
(7) Traffic signal equipment
(8) Disaster prevention / crime prevention equipment
(9) Data-processing equipment
(10) Applications of similar complexity and / or reliability requirements
to the applications listed in the above.
MURATA MFG.CO.,LTD
SpecNo.JEFL243C-0005S-01
Reference Only
P 6/9
16. Notice
Products can only be soldered with reflow.
This product is designed for solder mounting.
Please consult us in advance for applying other mounting method such as conductive adhesive.
16.1 Flux and Solder
Flux
Use rosin-based flux,(with converting chlorine content 0.06 to 0.1(wt)%. ),
but not highly acidic flux
(with Halogen content exceeding 0.2(wt)% conversion to chlorine).
Do not use water-soluble flux.
Solder
Use Sn-3.0Ag-0.5Cu solder
16.2 Assembling
Flow soldering may cause deterioration in insulation resistance.
So,reflow soldering shall be applied for this product.
16.3 Cleaning Conditions
Products shall be cleaned on the following conditions.
(1) Cleaning temperature shall be limited to 60°C max. (40°C max. for Isopropyl alcohol.)
(2) Ultrasonic cleaning shall comply with the following conditions, avoiding the resonance phenomenon
at the mounted products and P.C.B..
Power : 20W/ l max.,
Frequency : 28kHz to 40kHz,
Time : 5 minutes max.
(3) Cleaner
1. Alternative cleaner Isopropyl alcohol (IPA)
2. Aqueous agent
PINE ALPHA ST-100S
(4) There shall be no residual flux and residual cleaner after cleaning.
In the case of using aqueous agent, products shall be dried completely after rinse with de-ionized
water in order to remove the cleaner.
(5) Other cleaning
Please contact us.
16.4 Resin coating
The impedance value may change due to high cure-stress of resin to be used for coating/molding products.
An open circuit issue may occur by mechanical stress caused by the resin, amount/cured shape of resin, or
operating condition etc. Some resin contains some impurities or chloride possible to generate chlorine by
hydrolysis under some operating condition may cause corrosion of wire of coil, leading to open circuit. So,
please pay your careful attention when you select resin in case of coating/molding the products with the
resin.Prior to use the coating resin, please make sure no reliability issue is observed by evaluating products
mounted on your board.
16.5 Attention regarding P.C.B. bending
The following shall be considered when designing and laying out P.C.B.'s.
(1) P.C.B. shall be designed so that products are not subject to the mechanical stress due to
warping the board.
[Products direction]
a
Products shall be location the sideways
b
Direction (Length : a
P.C.B. shall be designed so that products are
far from the portion of perforation.
×
P.C.B.
○
○
The portion of perforation shall be designed
as narrow as possible, and shall be designed
so as not to be applied the stress in the case of P.C.B. separation.
Products shall not be arranged on the line of a series
of holes when there are big holes in P.C.B.
(Because the stress concentrate on the line of holes.)
Portion of
Perforation
Product
×
○
P.C.B.
×
Product
Hole
< Products Placing >
Support pins shall be set under P.C.B . to prevent causing a warp to P.C.B.
during placing the products on the other side of P.C.B.
< P.C.B. Separation >
P.C.B. shall not be separated with hand.
P.C.B. shall be separated with the fixture so as not to cause P.C.B. bending.
P.C.B.
2
Support pin
1
1.2
0.4
16.7 Standard Land Dimensions(Reflow)
Pick- up nozzle
Product
3
0.8
2.6
3
4
16.8 Standard Soldering Condition
1. Reflow Soldering
(1)Standard printing pattern of solder paste
Thickness of the solder paste should be 100 to 150µm.
Use the stencil of the right figure.
For the resist and copper foil pattern, use standard
land dimensions.
Use the Solder Sn-3.0Ag-0.5Cu for pattern printing.
Spread of soldering paste between lines may cause short
circuit of lines.
1.2
2
If the pattern is made with wider than 1.2mm. It will result to let component turn around,
because melting speed is different. In the worst case, short circuit between lines may be occured.
If the pattern is made with less than 0.4mm , in the worst case , short circuit between lines may be
occurred deu to the spread of soldering paste or mount placeing accuracy.
If the pattern is made with wider than 0.8mm, the strength of bending will be reduced.
Do not use gilded pattern. A copper wire may cause open by dissolution of metallization.
0.5
1
Resist
Copper foil pattern
No pattern
(in mm)
0.8
2.6
(in mm)
(2) Soldering Temperatutre
Temperature difference between soldering and surface of products must be within 150°C,
in preheating. When products are immersed in liquid after soldering, temperature difference
should be within 100°C. If preheating is not enough, ferrite may be cracked and cause deterioration in
insulation resistance.
(3) Soldering Condition
Standard soldering profile and the limit soldering profile is as follows.
The excessive limit soldering conditions may cause leaching of the electrode and / or resulting
in the deterioration of product quality.
MURATA MFG.CO.,LTD
SpecNo.JEFL243C-0005S-01
Reference Only
Temp.
P 8/9
260℃/10s
(℃)
245±3℃
220℃
230℃
Limit profile
180
150
Standard profile
30~60s
60s max.
90±30s
Pre-heating
Heating
Peak temperature
Cycle of reflow
Standard Profile
150~180°C 、90s±30s
above 220°C、30s~60s
245±3°C
2 times
Time(s)
Limit Profile
above 230°C、60s max.
260°C、10s
2 times
2. Reworking with Soldering iron
The following conditions must be strictly followed when using a soldering iron after being
mounted by reflow soldering.
· Pre-heating: 150°C, 1 min
· Soldering iron output: 30W max.
· Tip temperature: 350°C max.
· Tip diameter:φ3mm max.
· Soldering time : 3(+1,-0) seconds.
· Times : 2times max.
Notes : Do not touch the products directly with the soldering iron.
3. Solder Volume
Solder shall be used not to be exceed the upper limits as shown below.
Upper limit
Recommendable
t
T
1/3T≦t≦T (T:Tickness of electrode)
Accordingly increasing the solder volume, the mechanical stress to Chip is also increased.
Exceeding solder volume may cause the failure of mechanical or electrical performance.
16.9 Caution for use
・When you hold products with a tweezer, please hold like a figure of the right side,
and sharp material, such as a pair of tweezers, shall not be touched to the winding
portion to prevent the breaking of wire.
・Mechanical shock should not be applied to the products mounted on the board to prevent
the breaking of the core.
MURATA MFG.CO.,LTD
SpecNo.JEFL243C-0005S-01
Reference Only
P 9/9
16.10 Handling of a substrate
After mounting products on a substrate, do not apply any stress to the product caused by bending or twisting to
the substrate when cropping the substrate, inserting and removing a connector from the substrate or tightening
screw to the substrate.
Excessive mechanical stress may cause cracking in the product.
Bending
Twisting
16.11 Brushing of neighborhood of products
When you clean the neighborhood of products such as connector pins, bristles of cleaning brush
shall not be touched to the winding portion to prevent the breaking of wire.
16.12 Operating Environment
Do not use this product under the following environmental conditions, on deterioration
of the performance, such as insulation resistance may result from the use.
(1) in corrosive gases (acidic gases, alkaline gases, chlorine, sulfur gases, organic gases and etc.)
(2) in the atmosphere where liquid such as organic solvent, may splash on the products.
16.13 Storage Condition
(1) Storage period
Use the products within 12 months after delivered.
Solderability should be checked if this period is exceeded.
(2) Storage environment conditions
·Products should be stored in the warehouse on the following conditions.
Temperature : -10 ~ +40°C
Humidity
: 15 to 85% relative humidity No rapid change on temperature and humidity.
· Products should not be stored in corrosive gases, such as sulfureous, acid gases, alkaline gases,
to prevent the following deterioration.
Poor solderability due to the oxidized electrode.
· Products should be stored on the palette for the prevention of the influence from humidity,dust and so on.
· Products should be stored in the warehouse without heat shock, vibration, direct sunlight and so on.
· Products should not be stored under the air tights packaged condition.
(3) Delivery
Care should be taken when transporting or handling product to avoid excessive vibration or mechanical shock.
!
17.△
Note
(1)Please make sure that your product has been evaluated in view of your specifications with our product being
mounted to your product.
(2)You are requested not to use our product deviating from the reference specifications.
(3)The contents of this reference specification are subject to change without advance notice. Please approve our
product specifications or transact the approval sheet for product specifications before ordering.
MURATA MFG.CO.,LTD