Spec No. JEFL243C-9101P-01
P1/9
Wire Wound Chip Common Mode Choke Coil
DLW43SH□□□XK2□
Murata Standard Reference Specification [AEC-Q200]
1. Scope
This reference specification applies to Wire Wound Chip Common Mode Choke Coil DLW43SH_XK Series
for Automotive Electronics based on AEC-Q200.
2. Part Numbering
(ex.)
DL
W
43 S H
(1) (2) (3) (4) (5)
(1) Chip Common Mode Choke Coil
(2) Structure (W : Winding Type)
(3) Dimension (LW)
(4) Type
(5) Category
101
X K 2
L
(6) (7) (8) (9) (10)
(6) Inductance
(7) Circuit
(8) Features
(9) Number of Line
(10) Packaging Code
3. Rating
Customer
Part Number
L : Taping (Φ180mm/reel)
K : Taping (Φ330mm/reel)
B : Bulk
DC
Common Mode Inductance Rated Withstanding Rated
Current Resistance
Voltage
(Under Standard Testing Voltage
( max.)
(mA)
V(DC)
V(DC)
Condition)
Murata
Part Number
DLW43SH110XK2L
DLW43SH110XK2K
DLW43SH110XK2B
DLW43SH220XK2L
DLW43SH220XK2K
DLW43SH220XK2B
DLW43SH510XK2L
DLW43SH510XK2K
DLW43SH510XK2B
DLW43SH101XK2L
DLW43SH101XK2K
DLW43SH101XK2B
11uH (-30%/+50%)
at 0.1MHz
360
0.5
22uH (-30%/+50%)
at 0.1MHz
310
0.6
50
125
51uH (-30%/+50%)
at 1MHz
230
1.0
100uH(-30%/+50%)
at 1MHz
200
2.0
Operating Temperature : -40 to +125°C
Storage Temperature
4.Standard Testing Condition
Temperature : Ordinary Temperature 15 to 35°C
Humidity : Ordinary Humidity 25 to 85%(RH)
: -40 to +125°C
Temperature : 20 ± 2°C
Humidity : 60 to 70%(RH)
Atmospheric Pressure : 86 to106kPa
5. Style and Dimensions
■ Equivalent Circuits
2.6±0.2
(1)
(2)
(4)
(3)
(0.3)
(0.8)
4.5±0.2
3.2±0.2
No polarity
: Electr o de
( ) : R e f erenc e Valu e
■ Unit Mass (Typical value)
( in m m )
6. Marking
(0.6) : 100uH
(0.7) : 11,22,51uH
No Marking.
MURATA MFG.CO., LTD
0.17g
Insulation
Resistance
(Mmin.)
ESD
Rank
6:25kV
10
6
Spec No. JEFL243C-9101P-01
P2/9
7. Electrical Performance
No.
7.1
Item
Common Mode
Inductance (Lc)
7.2
Insulation
Resistance (I.R.)
Withstanding
Voltage
7.3
7.4
Specification
Meet item 3.
Products shall not be damaged.
DC Resistance
(Rdc)
Meet item 3.
Test Method
Measuring Equipment : KEYSIGHT 4294A or the
equivalent
Measuring Frequency:0.1MHz / 11uH, 22uH
1MHz / 51uH, 100uH (ref.item 9.1)
Measuring voltage : Rated Voltage
Measuring time : 1 minute max. (ref.item 9.3)
Test Voltage : 2.5 times for Rated Voltage
Time : 1 to 5 seconds
Charge Current : 1 mA max. (ref.item 9.2)
Measuring current : 10mA max. (ref.item 9.4)
(In case of doubt in the above mentioned standard
condition, measure by 4 terminal method.)
8. Q200 Requirement
8.1.Performance (based on Table 13 for Ferrite EMI SUPPRESSORS/FILTERS)
AEC-Q200 Rev.D issued June 1. 2010
AEC-Q200
No.
3
Item
High Temperature
Exposure
Murata Specification / Deviation
Specification
1000hours at 125 deg C
Set for 24hours at room
temperature, then measured.
Meet Table A after testing.
Table A
1000cycles
-40 deg C to +125 deg C
Set for 24hours at room
temperature, then measured.
Per EIA469
No electrical tests
Meet Table A after testing.
Appearance
No damage
Common Mode Inductance
(at 0.1MHz / 11uH, 22uH Meet item 3.
at 1MHz / 51uH, 100uH)
4
Temperature Cycling
5
Destructive
Physical Analysis
7
Biased Humidity
1000hours at 85 deg C, 85%RH
Apply max rated current.
Meet Table A after testing.
8
Operational Life
Apply 125 deg C1000hours
Set for 24hours at room
temperature, then measured.
Meet Table A after testing.
Apply rated current.
9 External Visual
10 Physical Dimension
Visual inspection
Meet ITEM 4
(Style and Dimensions)
No abnormalities
No defects
12 Resistance to
Solvents
Per MIL-STD-202 Method 215 Not Applicable
13 Mechanical Shock
Per MIL-STD-202 Method 213 Meet Table A after testing.
Conditon F:
1500g’s(14.7N)/0.5ms/Half sine
Not Applicable
(ref.item 9.5)
(ref.item 9.6)
MURATA MFG.CO., LTD
Spec No. JEFL243C-9101P-01
P3/9
AEC-Q200
15
Resistance
to Soldering Heat
17
ESD
18
Solderbility
Per J-STD-002
19
20
Electrical
Characterization
Flammability
Measured :
Common mode Inductance
Per UL-94
21
Board Flex
22
Terminal Strength
30
Electrical
Transient
Conduction
Epoxy-PCB(1.6mm)
Meet Table A after testing.
Deflection 2mm(min)
60 sec minimum holding time
Per AEC-Q200-006
No defects
A force of 17.7N for 60sec
Per ISO-7637-2
Not Applicable
14
Stress
Vibration
Murata Specification / Deviation
Test Method
5g's(0.049N) for 20 minutes,
12cycles each of 3 oritentations
Test from 10-2000Hz.
12cycles each of 3 oritentations
No-heating
Solder temperature
260C+/-5 deg C
Immersion time 10s
Per AEC-Q200-002
No.
Meet Table A after testing.
Pre-heating:150 to 180C / 90±30s
Meet Table A after testing.
Meet Table A after testing.
ESD Rank: Refer to Item 3. Rating.
Method b : Not Applicable
90% of the terminations is to be soldered.(except partly-exposed wire)
Flux:Ethanol solution of rosin,25(wt)% includes activator equivalent to
0.06 to 0.10(wt)% chlorine
No defects
Not Applicable
9. Terminal to be Tested.
When measuring and supplying the voltage, the following terminal is applied.
No.
Item
Terminal to be Tested
9.1
Common Mode Inductance
(Measurement Terminal)
Terminal
9.2
9.3
9.4
9.5
9.6
Withstanding Voltage
(Measurement Terminal)
Insulation Resistance
(Measurement Terminal)
Terminal
Terminal
Terminal
DC Resistance
(Measurement Terminal)
Biased Humidity
(Supply Terminal)
Terminal
Terminal
Terminal
Terminal
Terminal
Operational Life
(Supply Terminal)
Terminal
10. P.C.B., Flux, Solder and Soldering condition
Test shall be done using P.C.B., Flux, Solder and Soldering condition which are
specified in item 13 except the case of being specified special condition.
MURATA MFG.CO., LTD
Spec No. JEFL243C-9101P-01
P4/9
4.9±0.1
5.5
±0.05
1.5±0.1
0 4.0±0.1 2.0±0.05
3.6±0.1
8.0±0.1
0.3±0.05
12.0±0.2
11.1 Appearance and Dimensions ( 12mm-wide,Plastic tape)
1.75±0.1
11. Specification of Packaging
*Dimension of the Cavity is measured
at the bottom side.
Direction of feed
2.7±0.1
(in mm)
11.2. Specification of Taping
(1) Packing quantity (Standard quantity) 180 mm reel : 500 pcs. / reel 330 mm reel : 2500 pcs. / reel
(2) Packing Method
Products shall be packaged in each embossed cavity of plastic tape and sealed with cover tape.
(3) Sprocket Hole
The sprocket holes are to the right as the tape is pulled toward the user.
(4) Spliced point
The cover tape have no spliced point.
(5) Missing components number
Missing components number within 0.025% of the number per reel or 1 pc., whichever is greater,
and are not continuous. The specified quantity per reel is kept.
11.3. Pull Strength of Plastic Tape
Plastic Tape
Cover Tape
5 N min.
10 N min.
11.4. Peeling off force of Cover Tape
0.2N to 0.7N (minimum value is typical.)
165 to 180 degree
Speed of Peeling off : 300 mm / min
F
Cover tape
Plastic tape
11.5. Dimensions of Leader-tape, Trailer and Reel
There shall be leader-tape (cover tape only and empty tape) and trailer-tape (empty tape) as follows.
« Packaging Code : L (Φ180mm reel) »
2.0±0.5
Trailer
160 min.
Leader
210 min.
190 min.
Empty Tape Cover tape
Label
13.0±0.2
60± 1
0
21.0±0.8
13± 1
0
Direction of feed
17±1.4
0
180± 3
(in mm)
« Packaging Code : K (Φ330mm reel) »
2.0±0.5
Trailer
Leader
160 min.
190 min.
210 min.
Empty Tape Cover tape
Label
13.0±0.5
50 min.
21.0±0.8
2.0±0.5
14±1.5
Direction of feed
330±2.0
(in mm)
MURATA MFG.CO., LTD
Spec No. JEFL243C-9101P-01
P5/9
11.6 Marking for reel
Customer part number, MURATA part number, Inspection number(1), RoHS marking(2), Quantity, etc
1) « Expression of Inspection No. »
□□ OOOO
(1)
(2)
(3)
(1) Factory Code
(2) Date
First digit
: Year / Last digit of year
Second digit
: Month / Jan. to Sep. 1 to 9, Oct. to Dec. O,N,D
Third, Fourth digit : Day
(3) Serial No.
2) « Expression of RoHS marking »
ROHS – Y (△)
(1) (2)
(1) RoHS regulation conformity parts.
(2) MURATA classification number
11.7 Marking for Outside package
Customer name Purchasing Order Number, Customer Part Number, MURATA part number,
RoHS marking (2), Quantity, etc
11.8 Specification of Outer Case
W
D
H
Standard Reel
Quantity in
Outer Case
(Reel)
φ180mm
186
186
93
4
φ330mm
340
340
85
4
Label
Reel
H
D
W
12.
Outer Case Dimensions
(mm)
*Above Outer Case size is typical. It depends on a quantity of an order.
!
△
Caution
12.1 Mounting Direction
Mount products in right direction.
Wrong direction which is 90°rotated from right direction causes not only open or short circuit but also
flames or other serious trouble.
Z
right direction
Z
wrong direction
12.2 Limitation of Applications
Please contact us before using our products for the applications listed below which require especially
high reliability for the prevention of defects which might directly cause damage to the third party's life,
body or property.
(1) Aircraft equipment
(2) Aerospace equipment
(3) Undersea equipment
(4) Power plant control equipment
(5) Medical equipment
(6) Transportation equipment (trains, ships, etc.)
(7) Traffic signal equipment
(8) Disaster prevention / crime prevention equipment
(9) Data-processing equipment
(10) Applications of similar complexity and / or reliability requirements
to the applications listed in the above.
12.3 Caution(Rating)
Do not exceed maximum rated current of the product. Thermal stress may be transmitted to the product and
short/open circuit of the product or falling off the product may be occurred.
12.4 Fail-safe
Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that may be
caused by the abnormal function or the failure of our product.
13.5 Corrosive gas
Please refrain from use since contact with environments with corrosive gases (sulfur gas [hydrogen sulfide, sulfur
dioxide, etc.], chlorine, ammonia, etc.) or oils (cutting oil, silicone oil, etc.) that have come into contact with the
previously stated corrosive gas environment will result in deterioration of product quality or an open from
deterioration due to corrosion of product electrode, etc. We will not bear any responsibility for use under these
environments.
MURATA MFG.CO., LTD
Spec No. JEFL243C-9101P-01
P6/9
13. Notice
Products can only be soldered with reflow.
This product is designed for solder mounting.
Please consult us in advance for applying other mounting method such as conductive adhesive.
13.1 Flux and Solder
Flux
Use rosin-based flux,(with converting chlorine content 0.06 to 0.1(wt)%. ),
but not highly acidic flux
(with Halogen content exceeding 0.2(wt)% conversion to chlorine).
Do not use water-soluble flux.
Solder
Use Sn-3.0Ag-0.5Cu solder
Standard thickness of the solder paste should be 150µm.
13.2 Assembling
Flow soldering may cause deterioration in insulation resistance.
So, reflow soldering shall be applied for this product.
13.3 Cleaning Conditions
Do not clean after soldering. Some cleaning agents may degrade bonding strength,and
characteristics of products by detaching. If cleaning,please contact us.
13.4 Resin coating
The inductance value may change due to high cure-stress of resin to be used for coating/molding products. An open
circuit issue may occur by mechanical stress caused by the resin, amount/cured shape of resin, or operating
condition etc. Some resin contains some impurities or chloride possible to generate chlorine by hydrolysis under
some operating condition may cause corrosion of wire of coil, leading to open circuit. So, please pay your careful
attention when you select resin in case of coating/molding the products with the resin. Prior to use the coating resin,
please make sure no reliability issue is observed by evaluating products mounted on your board.
13.5 Attention regarding P.C.B. bending
The following shall be considered when designing and laying out P.C.B.'s.
(1) P.C.B. shall be designed so that products are not subject to the mechanical stress due to warping the board.
[Products direction]
a
b
〈 Poor example〉
Products shall be location the sideways
Direction (Length : a D is valid when stress is added vertically to the perforation as with Hand Separation.
If a Cutting Disc is used, stress will be diagonal to the PCB, therefore A > D is invalid.
MURATA MFG.CO., LTD
Stress Level
A > D *1
A > B
A > C
Spec No. JEFL243C-9101P-01
P7/9
(3) Mounting Components Near Screw Holes
When a component is mounted near a screw hole, it may be affected by the board deflection that occurs during
the tightening of the screw. Mount the component in a position as far away from the screw holes as possible.
Recommended
Screw Hole
13.6 Attention Regarding P.C.B. Design
< The Arrangement of Products >
P.C.B. shall be designed so that products are
far from the portion of perforation.
The portion of perforation shall be designed
as narrow as possible, and shall be designed
so as not to be applied the stress in the
case of P.C.B. separation.
Products shall not be arranged on the line
of a series of holes when there are big
holes in P.C.B.
(Because the stress concentrate on the
line of holes.)
Portion of
Perforation
×
P.C.B.
○
○
Portion of
Perforation
Product
×
○
P.C.B.
×
Product
Hole
< Products Placing >
Support pins shall be set under P.C.B .
to prevent causing a warp to P.C.B.
during placing the products on the other
side of P.C.B.
Pick- up nozzle
Product
P.C.B.
< P.C.B. Separation >
Support pin
P.C.B. shall not be separated with hand.
P.C.B. shall be separated with the fixture so as not to cause P.C.B. bending.
*2
3.4
1.6
13.7 Standard Land Dimensions (Reflow)
*3
A
1
5.9
*1
Part Number
A
DLW43SH110XK2
DLW43SH220XK2
DLW43SH510XK2
3.0
DLW43SH101XK2
Resist
Copper foil pattern
No Pattern
(in mm)
3.2
If the pattern is made with wider than 3.4mm. It will result to let component turn around,
because melting speed is different. In the worst case, short circuit between lines may be occured.
2 If the pattern is made with less than 1.6mm , in the worst case , short circuit between lines may be
occurred due to the spread of soldering paste or mount placing accuracy.
3 If the pattern is made with wider, the strength of bending will be reduced.
Moreover, if the pattern is made with less than "A" dimension , in the worst case short circuit may
be occurred.
4 Do not use gilded pattern. A copper wire may cause open by dissolution of metallization.
MURATA MFG.CO., LTD
Spec No. JEFL243C-9101P-01
P8/9
13.8 Standard Soldering Condition
1.Reflow Soldering
(1) Soldering Temperature
Temperature difference between soldering and surface of components must be within 150°C,
in preheating. When components are immersed in liquid after soldering, temperature difference
should be within 100°C. If preheating is not enough, components may be cracked and cause deterioration in
insulation resistance.
(2) Soldering Condition
Standard soldering profile and the limit soldering profile is as follows.
The excessive limit soldering conditions may cause leaching of the electrode and / or resulting
in the deterioration of product quality.
Soldering Profile for Lead Free solder (Sn-3.0Ag-0.5Cu solder )
Temp.
(°C)
260°C
245±3°C
220°C
240°C
Limit Profile
180
150
Standard Profile
30~60s
30s max.
90s±30s
Pre-heating
Heating
Peak temperature
Cycle of reflow
Standard Profile
150~180°C 、90s±30s
above 220°C、30s~60s
245±3°C
2 times
Time(s)
Limit Profile
above 240°C、30s max.
260°C、10s
2 times
2. Reworking with Soldering iron
The following conditions must be strictly followed when using a soldering iron after being
mounted by reflow soldering.
· Pre-heating: 150°C, 1 min
ꞏ Soldering iron output: 30W max.
· Tip temperature: 350°C max.
ꞏ Tip diameter:φ3mm max.
· Soldering time : 3(+1,-0) seconds. ꞏ Times : 2times max.
Notes : Do not touch the products directly with the soldering iron.
3. Solder Volume
Solder shall be used not to be exceeded the upper limits as shown below.
Upper limit
Recommendable
T
t
1/3T≦t≦T (T:Thickness of electrode)
Accordingly increasing the solder volume, the mechanical stress to Chip is also increased.
Exceeding solder volume may cause the failure of mechanical or electrical performance.
In case if the solder volume is much, we recommend to make the size of the solder paste
with less than the land pattern.
MURATA MFG.CO., LTD
Spec No. JEFL243C-9101P-01
P9/9
4.Solder fillet
Solder fillet in lateral direction is not formed in some case because of product's structure,
but it is not something that affects product's performance and reliability.
13.9 Caution for use
・When you hold products with a tweezer, please hold
like a figure of the right side, and sharp material,
such as a pair of tweezers, shall not be touched to
the winding portion to prevent the breaking of wire.
・Mechanical shock should not be applied to the products
mounted on the board to prevent the breaking
of the core.
tweezer
13.10 Handling of a substrate
After mounting products on a substrate, do not apply any stress to the product caused by bending or twisting to
the substrate when cropping the substrate, inserting and removing a connector from the substrate or tightening
screw to the substrate.
Excessive mechanical stress may cause cracking in the product.
Bending
Twisting
13.11 Brushing of neighborhood of products
When you clean the neighborhood of products such as connector pins, bristles of cleaning brush shall
not be touched to the winding portion to prevent the breaking of wire.
13.12 Operating Environment
Do not use this product under the following environmental conditions, on deterioration
of the performance, such as insulation resistance may result from the use.
(1) in corrosive gases (acidic gases, alkaline gases, chlorine, sulfur gases, organic gases and etc.)
(2) in the atmosphere where liquid such as organic solvent, may splash on the products.
13.13 Storage Condition
(1) Storage period
Use the products within 12 months after delivered.
Solderability should be checked if this period is exceeded.
(2) Storage environment conditions
ꞏProducts should be stored in the warehouse on the following conditions.
Temperature : -10 ~ +40°C
Humidity
: 15 to 85% relative humidity No rapid change on temperature and humidity.
ꞏ Products should not be stored in corrosive gases, such as sulfureous, acid gases, alkaline gases,
to prevent the following deterioration.
Poor solderability due to the oxidized electrode.
ꞏ Products should be stored on the palette for the prevention of the influence from humidity,dust and so on.
ꞏ Products should be stored in the warehouse without heat shock, vibration, direct sunlight and so on.
ꞏ Avoid storing the product by itself bare (i.e.exposed directly to air).
(3) Delivery
Care should be taken when transporting or handling product to avoid excessive vibration or mechanical shock.
14.! Note
(1)Please make sure that your product has been evaluated in view of your specifications with our product being
mounted to your product.
(2)You are requested not to use our product deviating from the reference specifications.
(3)The contents of this reference specification are subject to change without advance notice. Please approve our
product specifications or transact the approval sheet for product specifications before ordering.
MURATA MFG.CO., LTD