DLW5BSN302SQ2L

Noise Suppression Products/EMI Suppression Filters > Common Mode Choke Coil > Wire Wound Type for Large Current Data Sheet Common Mode Choke Coil 1 Wire Wound Type for Large Current DLW5AH/DLW5BS Series (2014/2020 Size) ■ Dimensions ■ Dimensions DLW5AH Series DLW5BS Series 0.45 min. * * (T) 4.3 max. Polarity Marking * The marking to indicate the product direction can be applicable. (Optional) 0.5 min. (W) 3.6±0.3 : Electrode (3) 1.7±0.3 (4) 1.3 0.9 1.3 ±0.3 ±0.3 ±0.3 (in mm) ■ Impedance-Frequency Characteristics (Main Items) 0.5 min. (4) (L) 5.0±0.3 0.45 min. 3.6±0.3 (W) 5.0±0.3 (1) (2) 1.3±0.3 1.7 1.3 1.7 ±0.3 ±0.3 ±0.3 position of wiring should * Starting be covered with resin. (T) 4.5 max. (2) 1.7±0.3 (1) (L) 5.0±0.3 : Electrode (3) 1.3±0.3 0.9±0.3 (in mm) ■ Equivalent Circuit 100000 Impedance (Ω) 10000 DLW5AHN402SQ2 DLW5BSN302SQ2 DLW5BSN152SQ2 DLW5BSN102SQ2 DLW5BSN351SQ2 DLW5BSN191SQ2 1000 (1) (2) (4) (3) Common mode 100 DLW5AHN402SQ2 DLW5BSN302SQ2 DLW5BSN152SQ2 Differential mode DLW5BSN102SQ2 DLW5BSN351SQ2 DLW5BSN191SQ2 No polarity. 10 1 10 100 1000 Frequency (MHz) ■ Packaging Code Packaging Minimum Quantity L 180mm Embossed Tape 400 K 330mm Embossed Tape 1500 B Bulk(Bag) 100 ■ Rated Value (p: packaging code) Part Number Common Mode Impedance (at 100MHz/20°C) Rated Current Rated Voltage Insulation Resistance (min.) Withstand Voltage DC Resistance Operating Temperature Range DLW5AHN402SQ2p 4000ohm (Typ.) 200mA 50Vdc 10M ohm 125Vdc 3.0ohm max. -25 to +85°C DLW5BSN191SQ2p 190ohm (Typ.) 5000mA 50Vdc 10M ohm 125Vdc 0.02ohm max. -40 to +85°C DLW5BSN351SQ2p 350ohm (Typ.) 2000mA 50Vdc 10M ohm 125Vdc 0.04ohm max. -40 to +85°C DLW5BSN102SQ2p 1000ohm (Typ.) 1500mA 50Vdc 10M ohm 125Vdc 0.06ohm max. -40 to +85°C Number of Circuit: 1 Continued on the following page. o This data sheet is applied for CHIP COMMON MODE CHOKE COIL used for General Electronics equipment for your design. ! Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2011.5.12 http://www.murata.com/ Noise Suppression Products/EMI Suppression Filters > Common Mode Choke Coil > Wire Wound Type for Large Current Data Sheet 2 Continued from the preceding page. Common Mode Impedance (at 100MHz/20°C) Part Number Rated Current Rated Voltage Insulation Resistance (min.) Withstand Voltage DC Resistance Operating Temperature Range DLW5BSN152SQ2p 1500ohm (Typ.) 1000mA 50Vdc 10M ohm 125Vdc 0.1ohm max. -40 to +85°C DLW5BSN302SQ2p 3000ohm (Typ.) 500mA 50Vdc 10M ohm 125Vdc 0.3ohm max. -40 to +85°C Number of Circuit: 1 ■ Derating of Rated Current DLW5BSN191SQ2 Temperature Derating Rated Current (A) 5 4.75 4.5 0 10 20 30 40 50 60 Operating Temperature (°C) 70 80 75°C 90 100 85°C ■ !Caution/Notice !Caution (Rating) Do not use products beyond the rated current and rated voltage as this may create excessive heat and deteriorate the insulation resistance. Notice Solderability of Tin plating termination chip might be deteriorated when low temperature soldering profile where peak solder temperature is below the Tin melting point is used. Please confirm the solderability of Tin plating termination chip before use. o This data sheet is applied for CHIP COMMON MODE CHOKE COIL used for General Electronics equipment for your design. ! Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2011.5.12 http://www.murata.com/