ECASD40E337M006KA0

Specification No. JECPY1-9006N-01 ROHS-Y SPECIFICATION For Reference Date：24/May/2021 Product Description：Polymer Aluminum Electrolytic Capacitor Customer Part Number： Murata Part Number：ECAS***********KA0 Series Murata Manufacturing Co.,Ltd. Chemical Device Department Sales Promotion Section (Company name/Dept.) All specifications may be changed without notice. Please check with our sales representatives or product engineers before ordering. 0F082B (Y15) Specification No. JECPY1-9006N-01 1. P. 2 / 13 Scope These specifications are applied to Polymer Aluminum Electrolytic Capacitor for electronic equipment use. Please contact us beforehand when you use it besides this use. 2. Part Number Description ① Series ：ECAS ② Dimensions ：See 3.1 ③ Rated Voltage ：See 3.2 ④ Capacitance ：See 3.3 ⑤ Capacitance Tolerance ：See 3.4 ⑥ ESR ：See 3.5 ⑦ Packing ：See 3.6 ⑧ Individual Specification Code 3. Descriptions 3.1 Dimensions Case Code D3 D4 D6 D9 3.2 ：Murata management Code （mm） L 7.3±0.3 7.3±0.3 7.3±0.3 7.3±0.3 W 4.3±0.2 4.3±0.2 4.3±0.2 4.3±0.3 T 1.4±0.1 1.9±0.1 2.8±0.3 4.2±0.3 W1 2.4±0.2 2.4±0.2 2.4±0.2 2.4±0.2 Rated Voltage Code 0D 0E 0G 0J 0K 1A 1B 1C 1D 1E Voltage 2V 2.5V 4V 6.3V 8V 10V 12.5V 16V 20V 25V Murata Manufacturing Co., Ltd. S 1.3±0.2 1.3±0.2 1.3±0.2 1.3±0.2 Specification No. JECPY1-9006N-01 3.3 P. 3 / 13 Capacitance This code is shown by three-digit numeric. The unit is pico-farad (pF). The first and the second figures show the significant digits of the nominal capacitance, and the third figure shows the number of “0” following the significant digit. Ex.) Code 476 107 227 477 3.4 Capacitance Tolerance Code M Y 3.5 Capacitance 47μF 100μF 220μF 470μF Tolerance ±20％ +10, -35% ESR This code is shown by three-digit alphanumeric. The unit is milli-ohm (mΩ). If there is a decimal point, it is expressed by the capital letter "R". Ex.) Code 4R5 009 010 3.6 Packing Code K 3.7 ESR 4.5mΩ 9mΩ 10mΩ Specification Φ330mmplastic taping packing Individual Specification Code Expressed by two figures. Murata Manufacturing Co., Ltd. Specification No. JECPY1-9006N-01 P. 4 / 13 4. Part Number and Minimum Packaging Quantity 4.1 Part Numbers and Standards Murata Part Number Rated Voltage (V.DC) Cap. (μF) Cap Tol. (%) Case Size ESR (mΩ) 100kHz/ +25℃ Leakage Current (μA) Ripple Current (Arms) 100kHz ECASD40D337M4R5KA0 2 330 ±20 D4 4.5 66.0 4.0 ECASD40D337M006KA0 2 330 ±20 D4 6 66.0 3.0 ECASD40E337M4R5KA0 2.5 330 ±20 D4 4.5 82.5 4.0 ECASD40E337M006KA0 2.5 330 ±20 D4 6 82.5 3.0 ECASD40E337M009KA0 2.5 330 ±20 D4 9 82.5 3.0 ECASD60G337M008KA0 4 330 ±20 D4 8 132.0 3.5 ECASD40J107M015KA0 6.3 100 ±20 D4 15 63.0 2.0 ECASD40J227M010KA0 6.3 220 ±20 D4 10 138.6 3.0 ECASD60J337M009KA0 6.3 330 ±20 D6 9 207.9 3.5 ECASD31A686M040KA0 10 68 ±20 D3 40 204.0 1.6 ECASD41A107M040KA0 10 100 ±20 D4 40 300.0 1.6 ECASD41C336M040KA0 16 33 ±20 D4 40 158.4 1.6 ECASD31C476M040KA0 16 47 ±20 D3 40 225.6 1.6 ECASD41C476M040KA0 16 47 ±20 D4 40 225.6 1.6 ECASD41C686M040KA0 16 68 ±20 D4 40 326.4 1.6 ECASD41D476M040KA0 20 47 ±20 D4 40 282.0 1.6 ECASD31E106M040KA0 25 10 ±20 D3 40 75.0 1.6 ECASD41E106M040KA0 25 10 ±20 D4 40 75.0 1.6 ECASD31E156M040KA0 25 15 ±20 D3 40 112.5 1.6 ECASD41E156M040KA0 25 15 ±20 D4 40 112.5 1.6 ECASD31E226M040KA0 25 22 ±20 D3 40 165.0 1.6 ECASD41E226M040KA0 25 22 ±20 D4 40 165.0 1.6 ECASD41E336M040KA0 25 33 ±20 D4 40 247.5 1.6 Murata Manufacturing Co., Ltd. Specification No. JECPY1-9006N-01 4.2 Minimum Packaging Quantity Case Size D3 D4 D6 D9 5. P. 5 / 13 Minimum Packaging Quantity(pcs) 3,000 3,000 2,500 2,000 Markings Capacitance Code (3 digits) Code 476 107 227 477 Polarity indicator bar (+) Rated Voltage (2 digits) Code 0D 0E 0G 0J 0K 1A 1B 1D 1E 6. Voltage 2V 2.5V 4V 6.3V 8V 10V 12.5V 20V 25V Capacitance 47μF 100μF 220μF 470μF Characteristics No Item Characteristics 1 Operating temperature range -40℃～＋105℃ 2 Leakage Current ≦The value of No.4.1 3 Capacitance tolerance (See No.4.1) 4 Dissipation Factor ≦0.06 5 ESR ≦The value of No.4.1 6 Allowable Ripple Current (See No.4.1) 7 Solderability More than 75% of each terminal face is covered by new solder Test Conditions Series resistor: 1000 ohm Applied voltage: Rated Voltage Measuring after 2 minutes of application Please conduct pre-conditioning below, if you have a doubt. Pre-conditioning: ・Temperature: 105℃. ・Applied voltage :Rated Voltage ・Series resistor:1000 ohm ・Charge time:1 hour. Then discharge and keep in the room temperature for 4h to 24h. Measuring frequency: 120Hz ±10% Measuring circuit: Equivalent series circuit Measuring voltage: +1Vr.m.s. Measuring temperature: 25 ℃ Measuring frequency: 100kHz ±10% Measuring voltage: no more than +1Vr.m.s. Measuring temperature: 25 ℃ Measuring frequency: 100kHz ±10% Part temperature: +20 to +105 ℃ Lead Free Solder: Sn/3.0Ag/0.5Cu Flux: Rosin 25%, IPA 75% Solder temperature: 245 ±3℃ Immersing time: 3 ±0.3s Murata Manufacturing Co., Ltd. Specification No. JECPY1-9006N-01 No. 8 9 10 11 12 Item Moisture resistance under no bias Moisture resistance under load Shelf life Endurance P. 6 / 13 Characteristics Leakage Current Capacitance Change Dissipation Factor Appearance Leakage Current Capacitance Change Dissipation Factor Appearance Leakage Current Capacitance Change Dissipation Factor Appearance Leakage Current Capacitance Change Dissipation Factor Appearance ≦ 300% of initial specified value ≦ 750% of initial specified value* -20% and +50% of initial measured value Leakage Current ≦The value of No.4.1 Capacitance Change ±10% of initial measured value Dissipation Factor ≦ 0.06 Appearance No defects or abnormalities ≦ 0.12 Test Conditions Test temperature: 60±2℃ Relative humidity: 90~95%RH Test time: 500+24, -0h No defects or abnormalities ≦The value of No.4.1 -20% and +50% of initial measured value ≦ 0.12 Test temperature: 60±2℃ Relative humidity: 90~95%RH Test time: 500+24, -0h Applied voltage: Rated Voltage No defects or abnormalities ≦The value of No.4.1 ±10% of initial measured value ≦ 0.06 Test temperature: 105±2℃ Test time: 1000+48, -0h No defects or abnormalities ≦The value of No.4.1 ±20% of initial measured value ≦ 0.06 Test temperature: 105±2℃ Test time: 2000+48, -0h Applied voltage: Rated Voltage No defects or abnormalities Surge Temperature: +85℃ for W.V. 2V~10V Room temp. for W.V. 12.5V~25V Applied voltage: Rated voltage x1.25 Current Limiting resistance: 33ohm (in series) for W.V. 2V~10V 1kohm (in series) for W.V. 12.5V~25V Discharge resistance: 33ohm (in series) for W.V. 2V~10V 1kohm (in series) for W.V. 12.5V~25V Charge on/off: 30 sec. each, 1000 times The measurement condition in No.2 to 4 applies to No.8 to 12. * The Leakage Current characteristic “≦750% of initial specified value” after Moisture resistance under no bias test is applied to the following part numbers： ECASD40D337M4R5KA0、ECASD40D337M006KA0、ECASD40E337M4R5KA0、 ECASD40E337M006KA0 Murata Manufacturing Co., Ltd. Specification No. JECPY1-9006N-01 P. 7 / 13 7. Packaging 7.1 Carrier Tape Configuration and Dimension Polarity (－) (＋) Type D3, D4 D6 D9 7.2 Cavity Size ( mm ) A* 4.60 4.60 4.45 B* 7.65 7.65 7.65 C* 2.16 3.20 4.55 D* 0.23 0.27 0.28 Minimum Qty. (pcs.) 3,000 2,500 2,000 * Nominal values Tape Packaging Capacitors will be inserted in embossed carrier tape that will be sealed with cover tape as described below. No more than half of a sprocket hole will be covered by cover tape. 7.3 Taping Leader Tape has a leader and a trailer as described below. Murata Manufacturing Co., Ltd. Specification No. JECPY1-9006N-01 7.4 P. 8 / 13 Cover Tape Peel Strength Cover tape peel strength required to be within the range of 0.1-0.8N when tested as below . F 165°～180° 90 ° ～180 ° Cover Tape カ バーテ ープ キャリアテープ Peeling Speed ： 300ｍｍ/min 7.5 Carrier Tape Empty Cavities of Carrier Tape Section Empty cavities of filled section must be lower than 0.1% or 1pc of the total of reel quantity and sequential empty cavities are not allowed. Devices placed in one reel must satisfy the specified reel quantity. 7.6 Reel Configuration and Dimension Tape with capacitors is wound in a reel as described below. W B A W 7.7 Reel Size Tape Width Φ330 12 A 330.0 ±2.0 B 100.0 ±1.0 W 17.4 ±1.5 (mm) W1 13.4 ±1.5 Labels on Reel Shipping Label that show the customer parts number, our parts number, our company name, inspection number and quantity, will be put in outside of reel. Please note the position of sipping label when feeding a tape. Murata Manufacturing Co., Ltd. Specification No. JECPY1-9006N-01 7.8 P. 9 / 13 Moisture Proof Aluminum Laminated Bag Packaging A reel of the products is packaged in a moisture proof aluminum laminated bag and labels are put on the bag as shown below. One desiccant and a humidity indicator are put on the backside of the reel before slightly drawing the vacuum and sealing the bag. Seal Shipping Label 400 Explanatory Label of bag 400 Unit: mm Note) The size of the Moisture Proof Aluminum Laminated Bag is a rough value. 7.9 Cardboard Box Packaging Moisture proof aluminum laminated bags of products are packaged in a cardboard box. 8. Quality Assurance ＜1＞Murata’s responsibility for the quality of this product shall be limited to those specified in this document. ＜2＞It is a customer’s responsibility to judge fitness of this product for assembly process, end use and operating environment. Murata Manufacturing Co., Ltd. Specification No. JECPY1-9006N-01 9. Caution for Use 9.1 Caution Limitation of the use P. 10 / 13 Please contact us before using our products for the applications listed below which require especially high reliability for the prevention of defects which might directly cause damage to the third party's life, body or property. ① Aircraft equipment ②Aerospace equipment ③Undersea equipment ④Power plant control equipment ⑤Medical equipment ⑥Transportation equipment (vehicles, trains, ships, etc.) ⑦Traffic signal equipment ⑧Disaster prevention/crime prevention equipment ⑨Data-processing equipment ⑩ Application of similar complexity and/or reliability requirements to the applications listed in the above. 9.2 Caution Storage Condition ＜1＞Term of warranty for this product is two years after packaging in a moisture-proof bag, under the conditions below with sealed packaging. Recommended storage environment Room temperature: Humidity: 5-30 degree no more than 60%RH ＜2＞Polymer aluminum electrolytic capacitors should not be stored in an atmosphere consisting of corrosive gas(e.g. hydrogen sulfide, sulfur dioxide, chlorine, ammonia gas, etc.). ＜3＞Polymer aluminum electrolytic capacitors should be stored in a dry atmosphere, avoiding direct sunlight and condensation. If capacitors are kept at a higher humidity, the following problems may occur: ① Leakage current will increase at the beginning of use and damage the circuit. ② Moisture absorbed in a resin will evaporate and expand with heat of mounting and damage the mold resin. ＜4＞Please confirm a dry state with a humidity indicator card after open immediately. If 20% indication was in a pink state after opened, it is recommended to bake under the conditions below. ＜5＞The capacitors should be kept dry using desiccators or any other methods after unsealing the moisture-proof packaging. If more than one week has passed under the recommended storage environment specified above after unsealing the packaging, it is recommended to bake under the conditions below. Recommended baking conditions Temperature: Time: 60(+0, -5) degree C 168 hours ＜6＞This product meets MSL-3. Murata Manufacturing Co., Ltd. Specification No. JECPY1-9006N-01 P. 11 / 13 Caution 9.3 Cautions for Use ＜1＞Prohibited Circuits for use Do not use the capacitor with the following circuit. ① Time-constant circuit ② Coupling circuits ③ 2 or more capacitors connected serially ④ Circuit which are greatly affected by leakage current ＜2＞Polarity Polymer aluminum electrolytic capacitor is polarized. Please not to reverse the polarity when using. If reverse voltage is applied even momentary, it may damage the oxide film and the capacitor itself. Please verify the orientation of the capacitor before use in accordance with the drawing of “Markings” in Item 5. ＜3＞Operating Voltage When DC-rated capacitors are to be used in AC or ripple current circuits, be sure to maintain the Vo-p value of the applied voltage or the Vo-p which contains DC bias within the rated voltage range. When the voltage is applied to the circuit, starting or stopping may generate irregular voltage for a transit period because of resonance or switching. Be sure to use a capacitor with a rated voltage range that includes these irregular voltages. ＜4＞Inrush Current Extreme inrush current may cause short circuit or leakage current increase. If the inrush current exceeds 20A, adding protection circuit is recommended. ＜5＞Allowable Ripple Current Please not to apply ripple current exceeding the allowable value specified in the standards in Item 4.1. If excessive current is applied, it may generate heat and the heat may damage the capacitor. The sum of DC voltage and the peak AC voltage shall not exceed the rated voltage. The sum of the DC voltage and the peak AC voltage shall not allow a voltage reversal. ＜6＞Operating Temperature The operating temperature limit depends on the capacitor. ① Do not apply temperature exceeding the upper operating temperature. It is necessary to select a capacitor with a suitable rated temperature that will cover the operating temperature range. Also it is necessary to consider the temperature distribution in equipment and the seasonal temperature variable factor. ② Consider the self-heating of the capacitor. The surface temperature of the capacitor shall be the upper operating temperature or less when including the self-heating factors. Murata Manufacturing Co., Ltd. Specification No. JECPY1-9006N-01 P. 12 / 13 ＜7＞Reflow Soldering ① Please not to apply excessive force to the capacitor during insertion as well as after soldering. The excessive force may result in damage to electrode terminals and/or degradation of electrical performance. ② Resistance testing to reflow soldering was conducted in accordance with the reflow profile described in Figure 1. If this profile is adopted, reflow soldering can be repeated no more than two times. ＜Figure 1.＞Our Recommended Reflow Profile ③ Please refer to figure below for designing land pattern. ＜8＞Operating environment Confirm the environment in which the equipment will operate is under the specified conditions. Do not use the equipment under the following environments. ① Being spattered with water or oil. ② Being exposed to direct sunlight. ③ Being exposed to Ozone, ultraviolet rays or radiation. ④ Being exposed to toxic gas (e.g. hydrogen sulfide, sulfur dioxide, chlorine, ammoniagas, etc.) ⑤ Being exposed to excessive vibrations or mechanical shocks. ⑥ Being exposed to condensable environments. Murata Manufacturing Co., Ltd. Specification No. JECPY1-9006N-01 P. 13 / 13 ＜9＞ Disposal Polymer aluminum electrolytic capacitors should be disposed of as industrial waste in accordance with laws. 9.4 Manufacturing factory Murata Electronics (Thailand), Ltd. 10. Proposal ① When you use, please evaluate in a state mounted by your product. ② Please do not use this product other than the mention contents of this specification. ③ We think that it is not appropriate to mention a contract matter about the business in specifications, a drawing, other technical documentations. Therefore, we invalidate it when there is a mention about the range of the responsibility of us such as a guarantee of quality, PL, industrial property, the export control in these technical documentations that your company was made. Pease offer these matters separately in the basic contract document etc. Murata Manufacturing Co., Ltd.