ERB1885C2D3R0BDX1D

o Part Numbering Chip Monolithic Ceramic Capacitors (Part Number) GR M 18 8 q w e r t B1 1H y 102 K u i A01 K o rDimension (T) qProduct ID wSeries Product ID GR ER GQ GM GN LL GJ GA !0 Code Dimension (T) Code Series 2 0.2mm M Tin Plated Layer 2 2-elements (Array Type) 4 Only for Information Devices / Tip & Ring 3 0.3mm 7 Only for Camera Flash Circuit 4 4-elements (Array Type) B High Frequency Type 5 0.5mm M High Frequency for Flow/Reflow Soldering 6 0.6mm 7 0.7mm A Monolithic Microchip 8 0.8mm 0.85mm D for Bonding 9 M Capacitor Array A 1.0mm L Low ESL Wide Width Type B 1.25mm A Eight-termination Low ESL Type C 1.6mm M Ten-termination Low ESL Type D 2.0mm M High Frequency Low Loss Type Tin Plated Type E 2.5mm F 3.2mm 2 for AC250V (r.m.s.) M 1.15mm 3 Safety Standard Recognized Type N 1.35mm R 1.8mm S 2.8mm eDimension (LgW) Code Dimension (LgW) EIA Q 1.5mm 02 0.4g0.2mm 01005 X Depends on individual standards. 03 0.6g0.3mm 0201 05 0.5g0.5mm 0202 08 0.8g0.8mm 0303 11 1.25g1.0mm 0504 15 1.0g0.5mm 0402 18 1.6g0.8mm 0603 1D 1.4g1.4mm 1X Depends on individual standards. 21 2.0g1.25mm 0805 22 2.8g2.8mm 1111 31 3.2g1.6mm 1206 32 3.2g2.5mm 1210 3X With the array type GNM series, "Dimension(T)" indicates the number of elements. Depends on individual standards. 42 4.5g2.0mm 1808 43 4.5g3.2mm 1812 52 5.7g2.8mm 2211 55 5.7g5.0mm 2220 Continued on the following page. Continued from the preceding page. tTemperature Characteristics Temperature Characteristic Codes Code Public STD Code Temperature Characteristics Referance Temperature Temperature Range Capacitance Change or Temperature Coefficient Operating Temperature Range 1X SL *1 JIS 20°C 20 to 85°C +350 to -1000ppm/°C -55 to 125°C 2C CH *1 JIS 20°C 20 to 125°C 0±60ppm/°C -55 to 125°C 2P PH *1 JIS 20°C 20 to 85°C -150±60ppm/°C -25 to 85°C 2R RH *1 JIS 20°C 20 to 85°C -220±60ppm/°C -25 to 85°C 2S SH *1 JIS 20°C 20 to 85°C -330±60ppm/°C -25 to 85°C 2T TH *1 JIS 20°C 20 to 85°C -470±60ppm/°C -25 to 85°C 3C CJ *1 JIS 20°C 20 to 125°C 0±120ppm/°C -55 to 125°C 3P PJ *1 JIS 20°C 20 to 85°C -150±120ppm/°C -25 to 85°C 3R RJ *1 JIS 20°C 20 to 85°C -220±120ppm/°C -25 to 85°C 3S SJ *1 JIS 20°C 20 to 85°C -330±120ppm/°C -25 to 85°C -25 to 85°C 3T TJ *1 JIS 20°C 20 to 85°C -470±120ppm/°C 3U UJ *1 JIS 20°C 20 to 85°C -750±120ppm/°C -25 to 85°C 4C CK *1 JIS 20°C 20 to 125°C 0±250ppm/°C -55 to 125°C 5C C0G *1 EIA 25°C 25 to 125°C 0±30ppm/°C -55 to 125°C 5G X8G *1 EIA 25°C 25 to 150°C 0±30ppm/°C -55 to 150°C 6C C0H *1 EIA 25°C 25 to 125°C 0±60ppm/°C -55 to 125°C 6P P2H *1 EIA 25°C 25 to 85°C -150±60ppm/°C -55 to 125°C 6R R2H *1 EIA 25°C 25 to 85°C -220±60ppm/°C -55 to 125°C 6S S2H *1 EIA 25°C 25 to 85°C -330±60ppm/°C -55 to 125°C 6T T2H *1 EIA 25°C 25 to 85°C -470±60ppm/°C -55 to 125°C 7U U2J *1 EIA 25°C 25 to 85°C -750±120ppm/°C -55 to 125°C B1 B *2 JIS 20°C -25 to 85°C ±10% -25 to 85°C B3 B JIS 20°C -25 to 85°C ±10% -25 to 85°C C7 X7S EIA 25°C -55 to 125°C ±22% -55 to 125°C C8 X6S EIA 25°C -55 to 105°C ±22% -55 to 105°C F1 F *2 JIS 20°C -25 to 85°C +30, -80% -25 to 85°C F5 Y5V EIA 25°C -30 to 85°C +22, -82% -30 to 85°C L8 X8L EIA 25°C -55 to 150°C +15, -40% -55 to 150°C R1 R *2 JIS 20°C -55 to 125°C ±15% -55 to 125°C R3 R JIS 20°C -55 to 125°C ±15% -55 to 125°C R6 X5R EIA 25°C -55 to 85°C ±15% -55 to 85°C R7 X7R EIA 25°C -55 to 125°C ±15% -55 to 125°C R9 X8R EIA 25°C -55 to 150°C ±15% -55 to 150°C -25 to 20°C -4700+100/-2500ppm/°C 20 to 85°C -4700+500/-1000ppm/°C 9E ZLM *3 20°C W0 - - 25°C -55 to 125°C ±10% *4 +22, -33% *5 -25 to 85°C -55 to 125°C *1 Please refer to table for Capacitance Change under reference temperature. *2 Capacitance change is specified with 50% rated voltage applied. *3,*4 Murata Temperature Characteristic Code. *4 Apply DC350V bias. *5 No DC bias. Continued on the following page. Continued from the preceding page. oCapacitance Change from each temperature JIS Code Capacitance Change from 20°C (%) Murata Code –55°C –25°C –10°C Max. Min. Max. Min. Max. 1X – – – – – Min. – 2C 0.82 –0.45 0.49 –0.27 0.33 –0.18 2P – – 1.32 0.41 0.88 0.27 2R – – 1.70 0.72 1.13 0.48 2S – – 2.30 1.22 1.54 0.81 2T – – 3.07 1.85 2.05 1.23 3C 1.37 –0.90 0.82 –0.54 0.55 –0.36 3P – – 1.65 0.14 1.10 0.09 3R – – 2.03 0.45 1.35 0.30 3S – – 2.63 0.95 1.76 0.63 3T – – 3.40 1.58 2.27 1.05 3U – – 4.94 2.84 3.29 1.89 4C 2.56 –1.88 1.54 –1.13 1.02 –0.75 EIA Code Capacitance Change from 25°C (%) Murata Code –55°C –30°C –10°C Max. Min. Max. Min. Max. Min. 0.58 –0.24 0.40 –0.17 0.25 –0.11 6C 0.87 –0.48 0.59 –0.33 0.38 –0.21 6P 2.33 0.72 1.61 0.50 1.02 0.32 6R 3.02 1.28 2.08 0.88 1.32 0.56 5C/5G 6S 4.09 2.16 2.81 1.49 1.79 0.95 6T 5.46 3.28 3.75 2.26 2.39 1.44 7U 8.78 5.04 6.04 3.47 3.84 2.21 yRated Voltage uCapacitance Code Rated Voltage 0G DC4V 0J DC6.3V 1A DC10V Expressed by three figures. The unit is pico-farad (pF). The first and second figures are significant digits, and the third figure expresses the number of zeros which follow the two numbers. If there is a decimal point, it is expressed by the capital letter "R". In this case, all figures are significant digits. 1C DC16V Ex.) Code Capacitance 1E DC25V R50 0.5pF 1H DC50V 1R0 1.0pF 2A DC100V 100 10pF 2D DC200V 103 10000pF 2E DC250V YD DC300V 2H DC500V 2J DC630V 3A DC1kV 3D DC2kV 3F DC3.15kV BB DC350V (for Camera Flash Circuit) E2 AC250V GB X2; AC250V (Safety Standard Recognized Type GB) GC X1/Y2; AC250V (Safety Standard Recognized Type GC) GD Y3; AC250V (Safety Standard Recognized Type GD) GF Y2, X1/Y2; AC250V (Safety Standard Recognized Type GF) Continued on the following page. Continued from the preceding page. iCapacitance Tolerance Capacitance Step Code Capacitance Tolerance TC Series B ±0.1pF C∆ GRM/GJM V5pF C∆–SL GRM/ERB/GQM V5pF * 1pF C∆ GJM