IntelliMAXt Advanced Load
Management Product
FPF2123-FPF2125
Description
The FPF2123, FPF2124, and FPF2125 are a series of load switches
which provide full protection to systems and loads which may
encounter large current conditions. These devices contain a 0.125 W
current−limited P−channel MOSFET which can operate over an input
voltage range of 1.8−5.5 V. The current limit is settable using
an external resistor. Internally, current is prevented from flowing
when the MOSFET is off and the output voltage is higher than the
input voltage. Switch control is by a logic input (ON) capable
of interfacing directly with low voltage control signals. Each part
contains thermal shutdown protection which shuts off the switch
to prevent damage to the part when a continuous over−current
condition causes excessive heating.
When the switch current reaches the current limit, the parts operate
in a constant−current mode to prohibit excessive currents from
causing damage. For the FPF2123 and FPF2124 if the constant current
condition still persists after 10 ms, these parts will shut off the switch.
The FPF2123 has an auto−restart feature which will turn the switch on
again after 160 ms if the ON pin is still active. The FPF2124 does not
have this auto−restart feature so the switch will remain off after
a current limit fault until the ON pin is cycled. The FPF2125 will not
turn off after a current limit fault, but will rather remain in the constant
current mode indefinitely. The minimum current limit is 150 mA.
These parts are available in a space−saving 5 pin SOT23 package.
Features
•
•
•
•
•
•
•
•
•
•
•
www.onsemi.com
SOT23−5
CASE 527AH
MARKING DIAGRAM
&E&E&Y
&O212X&C
&.&O&E&V
&E
&Y
&O
212X
&C
&.
&V
1.8 to 5.5 V Input Voltage Range
Controlled Turn−On
0.15−1.5 A Adjustable Current Limit
Under−Voltage Lockout
Thermal Shutdown
< 2 mA Shutdown Current
Auto Restart
Fast Current Limit Response Time
♦ 3 ms to Moderate Over Currents
Fault Blanking
Reverse Current Blocking
These Devices are Pb−Free and are RoHS Compliant
= Designates Space
= Binary Calendar Year Coding Scheme
= Plant Code identifier
= Device Specific Code
X = 3. 4 or 5
= Single digit Die Run Code
= Pin One Dot
= Eight−Week Binary Datecoding Scheme
ORDERING INFORMATION
See detailed ordering and shipping information on page 11 of
this data sheet.
Applications
•
•
•
•
•
•
•
PDAs
Cell Phones
GPS Devices
MP3 Players
Digital Cameras
Peripheral Ports
Hot Swap Supplies
© Semiconductor Components Industries, LLC, 2008
May, 2021 − Rev. 6
1
Publication Order Number:
FPF2125/D
FPF2123−FPF2125
Typical Application Circuit
VOUT
VIN
TO LOAD
FPF2123−FPF2125
ON
OFF ON
+
ISET
GND
−
Figure 1. Typical Application
Functional Block Diagram
VIN
UVLO
ON
REVERSE
CURRENT
BLOCKING
CONTROL
LOGIC
CURRENT
LIMT
VOUT
THERMAL
SHUTDOWN
ISET
GND
Figure 2. Block Diagram
Pin Configuration
VIN
1
GND
2
ON
3
5
VOUT
4
ISET
SOT23−5
Figure 3. Pin Assignment
www.onsemi.com
2
FPF2123−FPF2125
PIN DESCRIPTIONS
Pin
Name
1
VIN
Function
2
GND
3
ON
4
ISET
Current Limit Set Input: A resistor from ISET to ground sets the current limit for the switch.
5
VOUT
Switch Output: Output of the power switch
Supply Input: Input to the power switch and the supply voltage for the IC
Ground
ON Control Input
ABSOLUTE MAXIMUM RATINGS
Parameter
VIN, VOUT, ON, ISET to GND
Min
Max
Unit
−0.3
6.0
V
667
mW
Power Dissipation @ TA = 25°C (Note 1)
Operating Temperature Range
−40
125
°C
Storage Temperature
−65
150
°C
150
°C/W
Thermal Resistance, Junction to Ambient
Electrostatic Discharge Protection
HBM
4000
MM
400
V
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. Package power dissipation on 1 square inch pad, 2 oz copper board.
RECOMMENDED OPERATING CONDITIONS
Symbol
Min
Max
Unit
VIN
Input Voltage
Parameter
1.8
5.5
V
TA
Ambient Operating Temperature
−40
85
°C
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
ELECTRICAL CHARACTERISTICS
VIN = 1.8 to 5.5 V, TA = −40 to +85°C unless otherwise noted. Typical values are at VIN = 3.3 V and TA = 25°C.
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
BASIC OPERATION
VIN
Operating Voltage
IQ
Quiescent Current
1.8
IOUT = 0 mA
5.5
VIN = 1.8 to 3.3 V
75
VIN = 3.3 to 5.5 V
80
V
mA
120
ISHDN
Shutdown Current
2
mA
IBLOCK
Reverse Block Leakage Current
1
mA
ILATCHOFF
RON
Latch−Off Current
FPF2124
50
ON−Resistance
VIN = 3.3 V, IOUT = 50 mA, TA = 25°C
125
160
150
200
VIN = 3.3 V, IOUT = 50 mA, TA = 85°C
VIN = 3.3 V, IOUT = 50 mA, TA = −40°C to + 85°C
VIH
VIL
ON Input Logic High Voltage (ON)
ON Input Logic Low Voltage (ON)
65
VIN = 1.8 V
0.75
VIN = 5.5 V
1.30
mA
200
V
VIN = 1.8 V
0.5
VIN = 5.5 V
1.0
www.onsemi.com
3
mW
V
FPF2123−FPF2125
ELECTRICAL CHARACTERISTICS (continued)
VIN = 1.8 to 5.5 V, TA = −40 to +85°C unless otherwise noted. Typical values are at VIN = 3.3 V and TA = 25°C.
Symbol
Parameter
Test Condition
Min
Typ
Max
Unit
BASIC OPERATION
ISWOFF
ON Input Leakage
VON = VIN or GND
1
mA
Off Switch Leakage
VON = 0 V, VOUT = 0 V
1
mA
1000
mA
PROTECTIONS
ILIM
ILIM(min.)
UVLO
Current Limit
VIN = 3.3 V, VOUT = 3.0 V, RSET = 576 W
Min. Current Limit
VIN = 3.3 V, VOUT = 3.0 V
150
mA
Thermal Shutdown
Shutdown Threshold
140
°C
Return from Shutdown
130
Hysteresis
10
Under Voltage Shutdown
VIN Increasing
600
1.5
Under Voltage Shutdown
Hysteresis
800
1.6
1.7
V
50
mV
DYNAMIC
tON
Turn On Time
RL = 500 W, CL = 0.1 mF
25
ms
tOFF
Turn Off Time
RL = 500 W, CL = 0.1 mF
70
ms
tR
VOUT Rise Time
RL = 500 W, CL = 0.1 mF
12
ms
tF
VOUT Fall Time
RL = 500 W, CL = 0.1 mF
200
ms
Over Current Blanking Time
FPF2123, FPF2124
5
10
20
ms
Auto−Restart Time
FPF2123
80
160
320
ms
tBLANK
tRESTART
FPF2124, FPF2125
Short Circuit Response Time
NA
VIN = VON = 3.3 V
Moderate Over−Current Conditions
3
ms
VIN = VON = 3.3 V
Hard Short
20
ms
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
www.onsemi.com
4
FPF2123−FPF2125
TYPICAL CHARACTERISTICS
95
VON = VIN
74
SUPPLY CURRENT (mA)
SUPPLY CURRENT (mA)
76
72
70
68
66
64
62
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VIN = 3.3 V
75
VIN = 5.5 V
65
VIN = 1.8 V
55
45
−40
6
10
35
60
85
TJ, JUNCTION TEMPERATURE (°C)
Figure 4. Quiescent Current vs. Input Voltage
Figure 5. Quiescent Current vs. Temperature
500
SUPPLY CURRENT (nA)
2100
VIN = 5.5 V
1800
1500
1200
900
VIN = 3.3 V
600
300
450
400
350
VIN = 5.5 V
300
250
200
150
100
VIN = 3.3 V
50
0
−40
−15
10
35
60
0
−40
85
TJ, JUNCTION TEMPERATURE (°C)
0.18
1.2
SUPPLY CURRENT (mA)
1.4
0.15
0.12
0.09
0.06
0.03
2.0
2.5
3.0
3.5
4.0
4.5
5.0
10
35
60
85
Figure 7. ISWITCH−OFF Current vs. Temperature
0.21
0.00
1.5
−15
TJ, JUNCTION TEMPERATURE (°C)
Figure 6. ISHUTDOWN Current vs. Temperature
SUPPLY CURRENT (mA)
−15
SUPPLY VOLTAGE (V)
2400
SUPPLY CURRENT (nA)
85
5.5
1.0
VIN = 5.5 V
0.8
0.6
0.4
VIN = 3.3 V
0.2
0.0
−40
6.0
SUPPLY VOLTAGE (V)
−15
10
35
60
TJ, JUNCTION TEMPERATURE (°C)
Figure 8. Reverse Current vs. VOUT
Figure 9. Reverse Current vs. Temperature
www.onsemi.com
5
85
FPF2123−FPF2125
TYPICAL CHARACTERISTICS (Continued)
900
51.5
OUTPUT CURRENT (mA)
SUPPLY CURRENT (mA)
52.0
51.0
50.5
50.0
49.5
49.0
−40
−15
10
35
60
860
820
780
740
700
1.5
85
VIN − VOUT = 0.3 V
RSET = 576
2
2.5
Figure 10. ILATCH−OFF Current vs. Temperature
OUTPUT CURRENT (mA)
OUTPUT CURRENT (mA)
820
780
740
10
35
60
600
300
0
200
85
800
1400
1.2
160
1.0
150
0.8
0.6
130
120
0.2
110
5
3200
140
0.4
4
2600
Figure 13. Current Limit vs. Rest
170
3
2000
RSET (W)
RON (mW)
ON THRESHOLD (V)
6
900
1.4
2
5.5
1200
Figure 12. Current Limit vs. Temperature
1
5
1500
TJ, JUNCTION TEMPERATURE (°C)
0.0
4.5
1800
860
−15
4
Figure 11. Current Limit vs. Input Voltage
RSET = 576
700
−40
3.5
VIN, INPUT VOLTAGE (V)
TJ, JUNCTION TEMPERATURE (°C)
900
3
100
6
1
2
3
4
VIN, INPUT VOLTAGE (V)
VIN, INPUT VOLTAGE (V)
Figure 14. VIH vs. VIN
Figure 15. RON vs. VIN
www.onsemi.com
6
5
6
FPF2123−FPF2125
TYPICAL CHARACTERISTICS (Continued)
200
180
VIN = 1.8 V
160
RON (mW)
TURN−ON/OFF TIMES (ms)
100
140
VIN = 3.3 V
120
VIN = 5.5 V
100
80
60
−40
−15
10
35
60
TOFF
10
−40
85
TJ, JUNCTION TEMPERATURE (°C)
10
35
60
14
BLANKING TIME (ms)
TFALL
100
TRISE
10
VIN = 3.3 V
RL = 500 W
COUT = 0.1 mF
−15
10
35
60
13
12
11
10
9
8
−40
85
TJ, JUNCTION TEMPERATURE (°C)
−15
10
35
60
TJ, JUNCTION TEMPERATURE (°C)
Figure 19. TBLANK vs. Temperature
Figure 18. TRISE/TFALL vs. Temperature
200
RESTART TIME (ms)
190
VDRV2
2 V/DIV
180
170
VOUT
2 V/DIV
160
VIN = 3.3 V
RL = 2.2 W
CIN = 10 mF
COUT = 0.1 mF
150
140
130
120
−40
85
Figure 17. TON/TOFF vs Temperature
1000
RISE / FALL TIMES (ms)
−15
TJ, JUNCTION TEMPERATURE (°C)
Figure 16. R(ON) vs. Temperature
1
−40
TON
VIN = 3.3 V
RL = 500 W
COUT = 0.1 mF
IOUT
400 mA/DIV
−15
10
35
60
85
TJ, JUNCTION TEMPERATURE (°C)
Figure 20. TRESTART vs. Temperature
Figure 21. TBLANK Response
www.onsemi.com
7
85
FPF2123−FPF2125
TYPICAL CHARACTERISTICS (Continued)
VDRV2
2 V/DIV
VOUT
2 V/DIV
VON
2 V/DIV
VIN = 3.3 V
RL = 2.2 W
CIN = 10 mF
COUT = 0.1 mF
VIN = 3.3 V
RL = 500 W
CIN = 10 mF
COUT = 0.1 mF
IOUT
10 mA/DIV
IOUT
400 mA/DIV
Figure 23. TON Response
Figure 22. TRESTART Response
VON
2 V/DIV
VIN = 3.3 V
RL = 500 W
CIN = 10 mF
COUT = 0.1 mF
VIN
2 V/DIV
CIN = 10 mF
COUT = 0.1 mF
IOUT
4 A/DIV
IOUT
10 mA/DIV
VOUT
2 V/DIV
Figure 25. Short Circuit Response
(Output Shorted to GND)
Figure 24. TOFF Response
VIN
2 V/DIV
VIN = VON
2 V/DIV
CIN = 10 mF
COUT = 0.1 mF
VON
2 V/DIV
IOUT
400 mA/DIV
IOUT
400 mA/DIV
Figure 26. Current Limit Response
(Switch Power Up to Hard Short)
NOTE:
RL = 2.2 W
CIN = 10 mF
COUT = 0.1 mF
Figure 27. Current Limit Response
(Output Shorted to GND by 2.2 W, Moderate Short)
VDRV signal forces the device to go into overcurrent condition by loading a 2.2 W resistor.
www.onsemi.com
8
FPF2123−FPF2125
Description of Operation
Current Limiting
The FPF2123, FPF2124, and FPF2125 are current limited
switches that protect systems and loads which can be
damaged or disrupted by the application of high currents.
The core of each device is a 0.125 W P−channel MOSFET
and a controller capable of functioning over a wide input
operating range of 1.8−5.5 V. The controller protects against
system
malfunctions
through
current
limiting
under−voltage lockout and thermal shutdown. The current
limit is adjustable from 150 mA to 1.5 A through the
selection of an external resistor.
The current limit ensures that the current through the
switch doesn’t exceed a maximum value while not limiting
at less than a minimum value. The current at which the parts
will limit is adjustable through the selection of an external
resistor connected to ISET. Information for selecting the
resistor is found in the Application Info section. The
FPF2123 and FPF2124 have a blanking time of 10 ms,
nominally, during which the switch will act as a constant
current source. At the end of the blanking time, the switch
will be turned−off. The FPF2125 has no current limit
blanking period so it will remain in a constant current state
until the ON pin is deactivated or the thermal shutdown
turns−off the switch.
On/Off Control
The ON pin controls the state of the switch. When ON is
high, the switch is in the on state. Activating ON
continuously holds the switch in the on state so long as there
is no fault. For all versions, an under−voltage on VIN or a
junction temperature in excess of 140°C overrides the ON
control to turn off the switch. In addition, excessive currents
will cause the switch to turn off in the FPF2123 and
FPF2124. The FPF2123 has an Auto−Restart feature which
will automatically turn the switch on again after 160 ms. For
the FPF2124, the ON pin must be toggled to turn−on the
switch again. The FPF2125 does not turn off in response to
an over current condition but instead remains operating in a
constant current mode so long as ON is active and the
thermal shutdown or under−voltage lockout have not
activated.
The ON pin control voltage and VIN pin have independent
recommended operating ranges. The ON pin voltage can be
driven by a voltage level higher than the input voltage.
Under−Voltage Lockout
The under−voltage lockout turns−off the switch if the
input voltage drops below the under−voltage lockout
threshold. With the ON pin active, the input voltage rising
above the under−voltage lockout threshold will cause a
controlled turn−on of the switch which limits current
over−shoots.
Thermal Shutdown
The thermal shutdown protects the die from internally or
externally generated excessive temperatures. During an
over−temperature condition the switch is turned−off. The
switch automatically turns−on again if the temperature of
the die drops below the threshold temperature.
www.onsemi.com
9
FPF2123−FPF2125
APPLICATIONS INFORMATION
VOUT
VIN
FPF2123−FPF2125
Battery
5.5 V
−
ON
OFF ON
+
ISET
GND
5.5 V MAX
C1 = 4.7 mF
R2 = 110 W
C2 = 0.1 mF
RSET
Figure 28. Typical Application
Setting Current Limit
value, COUT(max), to prevent the part from registering an
over−current condition and turning−off the switch. The
maximum output capacitance can be determined from the
following formula,
The FPF2123, FPF2124, and FPF2125 have a current
limit which is set with an external resistor connected
between ISET and GND. This resistor is selected by using
the following equation (1),
R SET +
460
I LIM
(eq. 1)
C OUT(max) +
RSET is in Ohms and that of ILIM is Amps.
The table below can also be used to select RSET. A typical
application would be the 500 mA current that is required by
a single USB port. Using the table below an appropriate
selection for the RSET resistor would be 604 W. This will
ensure that the port load could draw 570 mA, but not more
than 950 mA. Likewise for a dual port system, an RSET of
340 W would always deliver at least 1120 mA and never
more than 1860 mA.
I LIM(min)
t BLANK(min)
V IN
(eq. 2)
Table 1. Current Limit Various RSET Values
Input Capacitor
To limit the voltage drop on the input supply caused by
transient in−rush currents when the switch turns−on into a
discharged load capacitance or a short−circuit, a capacitor
needs to be placed between VIN and GND. A 4.7 mF ceramic
capacitor, CIN, must be placed close to the VIN pin. A higher
value of CIN can be used to further reduce the voltage drop
experienced as the switch is turned on into a large capacitive
load.
Output Capacitor
A 0.1 mF capacitor, COUT, should be placed between
VOUT and GND. This capacitor will prevent parasitic board
inductances from forcing VOUT below GND when the
switch turns−off. For the FPF2123 and FPF2124, the total
output capacitance needs to be kept below a maximum
RSET [W]
Min. Current
Limit [mA]
Typ. Current
Limit [mA]
Max. Current
Limit [mA]
309
1120
1490
1860
340
1010
1350
1690
374
920
1230
1540
412
840
1120
1400
453
760
1010
1270
499
690
920
1150
549
630
840
1050
576
600
800
1000
604
570
760
950
732
470
630
790
887
390
520
650
1070
320
430
540
1300
260
350
440
1910
180
240
300
3090
110
150
190
www.onsemi.com
10
FPF2123−FPF2125
Power Dissipation
output is present will cause the temperature of the part to
increase. The junction temperature will only be able to
increase to the thermal shutdown threshold. Once this
temperature has been reached, toggling ON will not turn−on
the switch until the junction temperature drops. For the
FPF2125, a short on the output will cause the part to operate
in a constant current state dissipating a worst case power of,
During normal operation as a switch, the power dissipated
in the part will depend upon the level at which the current
limit is set. The maximum allowed setting for the current
limit is 1.5 A and this will result in a typical power
dissipation of,
P + (I LIM) 2
R ON + (1.5) 2
0.125 + 281 mW
(eq. 3)
P(max) + V IN(max)
If the part goes into current limit the maximum power
dissipation will occur when the output is shorted to ground.
For the FPF2123 the power dissipation will scale by the
Auto−Restart Time, tRESTART, and the Over Current
Blanking Time, tBLANK, so that the maximum power
dissipated is,
P(max) +
V IN(max)
20
80 ) 20
5.5
1.5 + 8.25 W
(eq. 5)
This large amount of power will activate the thermal
shutdown and the part will cycle in and out of thermal
shutdown so long as the ON pin is active and the short is
present.
t BLANK(max)
t RESTART(min) ) t BLANK(max)
I LIM(max) +
I LIM(max) + 5.5
Board Layout
For best performance, all traces should be as short as
possible. To be most effective, the input and output
capacitors should be placed close to the device to minimize
the effects that parasitic trace inductances may have on
normal and short−circuit operation. Using wide traces for
VIN, VOUT and GND will help minimize parasitic electrical
effects along with minimizing the case to ambient thermal
impedance.
1.5 + 1.65 W
(eq. 4)
This is more power than the package can dissipate, but the
thermal shutdown of the part will activate to protect the part
from damage due to excessive heating. When using the
FPF2124, attention must be given to the manual resetting of
the part. Continuously resetting the part when a short on the
ORDERING INFORMATION
Part Number
Current Limit
[A]
Current Limit
Blanking Time [ms]
Auto Restart
Time [ms]
On Pin Activity
Top Mark
Shipping†
FPF2123
0.15 − 1.5
5/10/20
80/160/320
Active HI
2123
3000 / Tape & Reel
FPF2124
0.15 − 1.5
5/10/20
NA
Active HI
2124
3000 / Tape & Reel
FPF2125
0.15 − 1.5
Infinite
NA
Active HI
2425
3000 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D
IntelliMAX is a trademark of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other coutries.
www.onsemi.com
11
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
SOT−23, 5 Lead
CASE 527AH
ISSUE A
DATE 09 JUN 2021
q
q
q
q
q
q1
q2
GENERIC
MARKING DIAGRAM*
XXXM
XXX = Specific Device Code
M = Date Code
*This information is generic. Please refer to
device data sheet for actual part marking.
Pb−Free indicator, “G” or microdot “G”, may
or may not be present. Some products may
not follow the Generic Marking.
DOCUMENT NUMBER:
DESCRIPTION:
98AON34320E
SOT−23, 5 LEAD
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
PAGE 1 OF 1
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2019
www.onsemi.com
onsemi,
, and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates
and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property.
A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any
products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the
information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use
of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products
and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information
provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may
vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license
under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems
or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should
Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Email Requests to: orderlit@onsemi.com
onsemi Website: www.onsemi.com
◊
TECHNICAL SUPPORT
North American Technical Support:
Voice Mail: 1 800−282−9855 Toll Free USA/Canada
Phone: 011 421 33 790 2910
Europe, Middle East and Africa Technical Support:
Phone: 00421 33 790 2910
For additional information, please contact your local Sales Representative