Is Now Part of
To learn more about ON Semiconductor, please visit our website at
www.onsemi.com
Please note: As part of the Fairchild Semiconductor integration, some of the Fairchild orderable part numbers
will need to change in order to meet ON Semiconductor’s system requirements. Since the ON Semiconductor
product management systems do not have the ability to manage part nomenclature that utilizes an underscore
(_), the underscore (_) in the Fairchild part numbers will be changed to a dash (-). This document may contain
device numbers with an underscore (_). Please check the ON Semiconductor website to verify the updated
device numbers. The most current and up-to-date ordering information can be found at www.onsemi.com. Please
email any questions regarding the system integration to Fairchild_questions@onsemi.com.
ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number
of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right
to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON
Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON
Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s
technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA
Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended
or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out
of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor
is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
FSL136MR
Green Mode Fairchild Power Switch (FPS™)
Features
Description
The FSL136MR integrated Pulse Width Modulator
(PWM) and SenseFET is specifically designed for highperformance offline Switch-Mode Power Supplies
(SMPS) with minimal external components. FSL136MR
includes integrated high-voltage power switching
regulators that combine an avalanche-rugged
SenseFET with a current-mode PWM control block.
Internal Avalanche-Rugged SenseFET (650V)
Under 50mW Standby Power Consumption at
265VAC, No-load Condition with Burst Mode
Precision Fixed Operating Frequency with
Frequency Modulation for Attenuating EMI
Internal Startup Circuit
Built-in Soft-Start: 15ms
Pulse-by-Pulse Current Limiting
Various Protections: Over-Voltage Protection
(OVP), Overload Protection (OLP), Output-Short
Protection (OSP), Abnormal Over-Current
Protection (AOCP), Internal Thermal Shutdown
Function with Hysteresis (TSD)
Auto-Restart Mode
Under-Voltage Lockout (UVLO)
Low Operating Current: 1.8mA
Adjustable Peak Current Limit
The integrated PWM controller includes: Under-Voltage
Lockout (UVLO) protection, Leading-Edge Blanking
(LEB), a frequency generator for EMI attenuation, an
optimized gate turn-on/turn-off driver, Thermal
Shutdown (TSD) protection, and temperaturecompensated precision current sources for loop
compensation and fault protection circuitry. The
FSL136MR offers good soft-start performance. When
compared to a discrete MOSFET and controller or RCC
switching converter solution, the FSL136MR reduces
total component count, design size, and weight; while
increasing efficiency, productivity, and system reliability.
This device provides a basic platform that is well suited
for the design of cost-effective flyback converters.
Applications
Maximum Output Power(1)
SMPS for VCR, STB, DVD, & DVCD Players
(2)
230VAC ± 15%
SMPS for Home Appliance
(3)
Adapter
Adapter
19W
Related Resources
Open
Frame
26W
85-265VAC
(3)
Adapter
14W
Open
Frame
20W
Notes:
AN-4137 — Design Guidelines for Off-line Flyback
Converters using FPS™
AN-4141 — Troubleshooting and Design Tips for
Fairchild Power Switch (FPS™) Flyback
Applications
AN-4147 — Design Guidelines for RCD Snubber of
Flyback
1.
2.
3.
The junction temperature can limit the maximum
output power.
230VAC or 100/115VAC with doubler.
Typical continuous power in a non-ventilated
enclosed adapter measured at 50°C ambient.
Ordering Information
Part Number
Operating
Temperature Range
Top Mark
FSL136MR
-40 to +105°C
FSL136MR
© 2009 Fairchild Semiconductor Corporation
FSL136MR • Rev. 1.0.7
Package
8-Lead, Dual Inline Package (DIP)
Packing Method
Rail
www.fairchildsemi.com
FSL136MR — Green Mode Fairchild Power Switch (FPS™)
June 2010
FSL136MR — Green Mode Fairchild Power Switch (FPS™)
Typical Application Diagram
Figure 1. Typical Application
Internal Block Diagram
V ST R
5
VCC
2
D ra in
6 ,7 ,8
IC H
V B U R L/V B U R H
V CC
8 V /1 2V
V CC Good
Inte rna l
B ia s
V R EF
V CC
I D EL A Y
R a ndom
Fre que nc y
G e ne ra tor
IF B
V FB 3
OSC
PWM
2 .5 R
S
Q
R
Q
G a te
Driv e r
R
IPK 4
O n -Tim e
D e te c tor
LE B
S oft
S ta rt
OSP
V SD
V CC Good
VCC
V O VP
S
Q
R
Q
1 GN D
A OC P
V AO C P
TS D
Figure 2. Internal Block Diagram
© 2009 Fairchild Semiconductor Corporation
FSL136MR • Rev. 1.0.7
www.fairchildsemi.com
2
Figure 3. Pin Configuration
Pin Definitions
Pin #
Name
1
GND
Ground. SenseFET source terminal on the primary side and internal control ground.
2
VCC
Positive Supply Voltage Input. Although connected to an auxiliary transformer winding,
current is supplied from pin 5 (VSTR) via an internal switch during startup (see Figure 2). Once
VCC reaches the UVLO upper threshold (12V), the internal startup switch opens and device
power is supplied via the auxiliary transformer winding.
3
VFB
Feedback Voltage. The non-inverting input to the PWM comparator, it has a 0.4mA current
source connected internally, while a capacitor and opto-coupler are typically connected
externally. There is a delay while charging external capacitor CFB from 2.4V to 6V using an
internal 5µA current source. This delay prevents false triggering under transient conditions, but
still allows the protection mechanism to operate under true overload conditions.
4
IPK
Peak Current Limit. Adjusts the peak current limit of the SenseFET. The feedback 0.4mA
current source is diverted to the parallel combination of an internal 6kΩ resistor and any
external resistor to GND on this pin to determine the peak current limit.
5
VSTR
Startup. Connected to the rectified AC line voltage source. At startup, the internal switch
supplies internal bias and charges an external storage capacitor placed between the VCC pin
and ground. Once VCC reaches 12V, the internal switch is opened.
6, 7, 8
Drain
Drain. Designed to connect directly to the primary lead of the transformer and capable of
switching a maximum of 650V. Minimizing the length of the trace connecting these pins to the
transformer decreases leakage inductance.
Description
© 2009 Fairchild Semiconductor Corporation
FSL136MR • Rev. 1.0.7
FSL136MR — Green Mode Fairchild Power Switch (FPS™)
Pin Configuration
www.fairchildsemi.com
3
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be
operable above the recommended operating conditions and stressing the parts to these levels is not recommended.
In addition, extended exposure to stresses above the recommended operating conditions may affect device
reliability. The absolute maximum ratings are stress ratings only. TJ = 25°C, unless otherwise specified.
Symbol
Parameter
Min.
Max.
Unit
VSTR
VSTR Pin Voltage
-0.3
650.0
V
VDS
Drain Pin Voltage
-0.3
650.0
V
VCC
Supply Voltage
26
V
VFB
Feedback Voltage Range
-0.3
12.0
V
ID
Continuous Drain Current
3
A
12
A
IDM
Drain Current Pulsed
(4)
(5)
EAS
Single Pulsed Avalanche Energy
230
mJ
PD
Total Power Dissipation
1.5
W
TJ
Operating Junction Temperature
TA
Operating Ambient Temperature
TSTG
ESD
Internally Limited
Storage Temperature
Human Body Model, JESD22-A114
(6)
Charged Device Model, JESD22-C101
ΘJA
Junction-to-Ambient Thermal Resistance
ΘJC
Junction-to-Case Thermal Resistance
ΘJT
Junction-to-Top Thermal Resistance
+105
°C
-55
+150
°C
5.0
(6)
KV
1.5
(7,8)
(7,9)
(7,10)
°C
-40
80
°C/W
19
°C/W
33.7
°C/W
FSL136MR — Green Mode Fairchild Power Switch (FPS™)
Absolute Maximum Ratings
Notes:
4. Repetitive rating: pulse width limited by maximum junction temperature.
5. L=51mH, starting TJ=25°C.
6. Meets JEDEC standards JESD 22-A114 and JESD 22-C101.
7. All items are tested with the standards JESD 51-2 and JESD 51-10.
8. ΘJA free-standing, with no heat-sink, under natural convection.
9. ΘJC junction-to-lead thermal characteristics under ΘJA test condition. TC is measured on the source #7 pin closed
to plastic interface for ΘJA thermo-couple mounted on soldering.
10. ΘJT junction-to-top of thermal characteristic under ΘJA test condition. Tt is measured on top of package. Thermocouple is mounted in epoxy glue.
© 2009 Fairchild Semiconductor Corporation
FSL136MR • Rev. 1.0.7
www.fairchildsemi.com
4
TA = 25°C unless otherwise specified.
Symbol
Parameter
Conditions
Min.
Typ.
Max. Units
SenseFET Section
BVDSS
Drain-Source Breakdown Voltage
IDSS
Zero Gate Voltage Drain Current
VDS = 650V, VGS = 0V
Drain-Source On-State Resistance
VGS = 10V, VGS = 0V, TC = 25°C
3.5
RDS(ON)
VCC = 0V, ID = 250µA
650
V
250
µA
4.0
Ω
CISS
Input Capacitance
VGS = 0V, VDS = 25V, f = 1MHz
290
pF
COSS
Output Capacitance
VGS = 0V, VDS = 25V, f = 1MHz
45
pF
CRSS
Reverse Transfer Capacitance
VGS = 0V, VDS = 25V, f = 1MHz
5.5
pF
td(ON)
Turn-On Delay
VDD = 350V, ID = 3.5A
12
ns
Rise Time
VDD = 350V, ID = 3.5A
22
ns
Turn-Off Delay
VDD = 350V, ID = 3.5A
20
ns
Fall Time
VDD = 350V, ID = 3.5A
19
ns
tr
td(OFF)
tf
Control Section
fOSC
∆fOSC
Switching Frequency
VDS = 650V, VGS = 0V
Switching Frequency Variation
VGS = 10V, VGS = 0V, TC = 125°C
fFM
Frequency Modulation
DMAX
Maximum Duty Cycle
VFB = 4V
DMIN
Minimum Duty Cycle
VFB = 0V
VSTART
VSTOP
61
67
73
KHz
±5
±10
%
±3
UVLO Threshold Voltage
After Turn-On
71
77
KHz
83
%
0
0
0
%
11
12
13
V
7
8
9
V
IFB
Feedback Source Current
VFB = 0V
320
400
480
µA
tS/S
Internal Soft-Start Time
VFB = 4V
10
15
20
ms
0.4
0.5
0.6
V
0.25
0.35
0.45
V
FSL136MR — Green Mode Fairchild Power Switch (FPS™)
Electrical Characteristics
Burst Mode Section
VBURH
VBURL
TJ = 25°C
Burst Mode Voltage
VBUR(HYS)
150
mV
Protection Section
ILIM
Peak Current Limit
tCLD
Current Limit Delay Time
VSD
Shutdown Feedback Voltage
VCC = 15V
IDELAY
Shutdown Delay Current
VFB = 5V
3.5
VOVP
Over-Voltage Protection Threshold
VFB = 2V
22.5
1.00
Output-Short
(11)
Protection
VAOCP
AOCP Voltage
TSD
Thermal
(11)
Shutdown
tLEB
(11)
TJ = 25°C
Shutdown
Temperature
5.5
2.41
6.0
6.5
V
5.0
6.5
µA
24.0
25.5
V
1.35
µs
1.60
V
2.0
2.5
µs
0.85
1.00
1.15
V
125
137
150
°C
60
(11)
A
ns
1.44
Hysteresis
Leading-Edge Blanking Time
2.15
200
TJ = 25°C
Threshold Feedback OSP Triggered When tONVOSP and Lasts Longer than
tOSP_FB
Feedback Blanking
Time
tOSP_FB
HYSTSD
1.89
Threshold Time
tOSP
VOSP
TJ = 25°C, di/dt = 300mA/µs
(11)
300
°C
ns
Continued on the following page…
© 2009 Fairchild Semiconductor Corporation
FSL136MR • Rev. 1.0.7
www.fairchildsemi.com
5
TA = 25°C unless otherwise specified.
Symbol
Parameter
Conditions
Min. Typ. Max. Units
Total Device Section
IOP1
Operating Supply Current
(While Switching)
IOP2
ICH
VSTR
(11)
VCC = 14V, VFB > VBURH
2.5
3.5
mA
Operating Supply Current
(Control Part Only)
VCC = 14V, VFB < VBURL
1.8
2.5
mA
Startup Charging Current
VCC = 0V
1.10
1.30
mA
Minimum VSTR Supply Voltage
VCC = VFB = 0V, VSTR Increase
Note:
11. Though guaranteed by design, it is not 100% tested in production.
© 2009 Fairchild Semiconductor Corporation
FSL136MR • Rev. 1.0.7
0.90
35
V
FSL136MR — Green Mode Fairchild Power Switch (FPS™)
Electrical Characteristics (Continued)
www.fairchildsemi.com
6
These characteristic graphs are normalized at TA=25.
Operating Frequency (fOSC)
Maximum Duty Cycle (DMAX)
1.4
1.4
1.3
1.3
1.2
1.2
1.1
1.1
1
1
0.9
0.9
0.8
0.8
0.7
0.7
0.6
0.6
‐40Ԩ ‐25Ԩ
0Ԩ
25Ԩ
50Ԩ
75Ԩ 100Ԩ 120Ԩ 140Ԩ
‐40Ԩ ‐25Ԩ
Figure 4. Operating Frequency vs. Temperature
0Ԩ
25Ԩ
50Ԩ
75Ԩ 100Ԩ 120Ԩ 140Ԩ
Figure 5. Maximum Duty Cycle vs. Temperature
Start Threshold Voltage (V START)
Operating Supply Current (Iop2)
1.4
1.4
1.3
1.3
1.2
1.2
1.1
1.1
1.0
1.0
0.9
0.9
0.8
0.8
0.7
0.7
0.6
FSL136MR — Green Mode Fairchild Power Switch (FPS™)
Typical Performance Characteristics
0.6
‐40
‐25
0
25
50
75
100
120
140
‐40
Figure 6. Operating Supply Current vs. Temperature
‐25
0
25
50
75
100
120
140
Figure 7. Start Threshold Voltage vs. Temperature
Stop Threshold Voltage (V STOP)
Feedback Source Current (IFB)
1.4
1.4
1.3
1.3
1.2
1.2
1.1
1.1
1.0
1
0.9
0.9
0.8
0.8
0.7
0.7
0.6
0.6
‐40
‐25
0
25
50
75
100
120
‐40 Ԩ ‐25 Ԩ
140
Figure 8. Stop Threshold Voltage vs. Temperature
© 2009 Fairchild Semiconductor Corporation
FSL136MR • Rev. 1.0.7
0Ԩ
25Ԩ
50 Ԩ
75 Ԩ 100 Ԩ 120 Ԩ 140 Ԩ
Figure 9. Feedback Source Current vs. Temperature
www.fairchildsemi.com
7
These characteristic graphs are normalized at TA=25.
Peak Current Limit (ILIM)
Startup Charging Current (ICH)
1.4
1.4
1.3
1.3
1.2
1.2
1.1
1.1
1
1
0.9
0.9
0.8
0.8
0.7
0.7
0.6
0.6
‐40Ԩ ‐25Ԩ
0Ԩ
25Ԩ
50Ԩ
75Ԩ 100Ԩ 120Ԩ 140Ԩ
‐40Ԩ ‐25Ԩ
0Ԩ
25Ԩ
50Ԩ
75Ԩ 100Ԩ 120Ԩ 140Ԩ
Figure 10. Startup Charging Current vs. Temperature
Figure 11. Peak Current Limit vs. Temperature
Burst Operating Supply Current (Iop1 )
Over‐Voltage Protection (V OVP)
1.4
1.4
1.3
1.3
1.2
1.2
1.1
1.1
1.0
1
0.9
0.9
0.8
0.8
0.7
0.7
FSL136MR — Green Mode Fairchild Power Switch (FPS™)
Typical Performance Characteristics (Continued)
0.6
0.6
‐40
‐25
0
25
50
75
100
120
‐40Ԩ ‐25Ԩ
140
Figure 12. Burst Operating Supply Current
vs. Temperature
© 2009 Fairchild Semiconductor Corporation
FSL136MR • Rev. 1.0.7
0Ԩ
25Ԩ
50Ԩ
75Ԩ 100Ԩ 120Ԩ 140Ԩ
Figure 13. Over-Voltage Protection
vs. Temperature
www.fairchildsemi.com
8
Startup
Feedback Control
At startup, an internal high-voltage current source
supplies the internal bias and charges the external
capacitor (CA) connected with the VCC pin, as illustrated
in Figure 14. When VCC reaches the start voltage of
12V, the FPS™ begins switching and the internal highvoltage current source is disabled. The FPS continues
normal switching operation and the power is provided
from the auxiliary transformer winding unless VCC goes
below the stop voltage of 8V.
FSL136MR employs current-mode control, as shown in
Figure 16. An opto-coupler (such as the FOD817A) and
shunt regulator (such as the KA431) are typically used
to implement the feedback network. Comparing the
feedback voltage with the voltage across the RSENSE
resistor makes it possible to control the switching duty
cycle. When the shunt regulator reference pin voltage
exceeds the internal reference voltage of 2.5V, the
opto-coupler LED current increases, the feedback
voltage VFB is pulled down, and the duty cycle is
reduced. This typically occurs when the input voltage is
increased or the output load is decreased.
Figure 14. Startup Circuit
Figure 16. Pulse-Width-Modulation Circuit
Oscillator Block
The oscillator frequency is set internally and the FPS
has a random frequency fluctuation function.
Fluctuation of the switching frequency of a switched
power supply can reduce EMI by spreading the energy
over a wider frequency range than the bandwidth
measured by the EMI test equipment. The amount of
EMI reduction is directly related to the range of the
frequency variation. The range of frequency variation is
fixed internally; however, its selection is randomly
chosen by the combination of external feedback voltage
and internal free-running oscillator. This randomly
chosen switching frequency effectively spreads the EMI
noise nearby switching frequency and allows the use of
a cost-effective inductor instead of an AC input line filter
to satisfy the world-wide EMI requirements.
Leading-Edge Blanking (LEB)
FSL136MR — Green Mode Fairchild Power Switch (FPS™)
Functional Description
At the instant the internal SenseFET is turned on, the
primary-side capacitance and secondary-side rectifier
diode reverse recovery typically cause a high-current
spike through the SenseFET. Excessive voltage across
the RSENSE resistor leads to incorrect feedback
operation in the current-mode PWM control. To counter
this effect, the FPS employs a leading-edge blanking
(LEB) circuit (see the Figure 16). This circuit inhibits the
PWM comparator for a short time (tLEB) after the
SenseFET is turned on.
Protection Circuits
The FPS has several protective functions, such as
overload protection (OLP), over-voltage protection
(OVP), output-short protection (OSP), under-voltage
lockout (UVLO), abnormal over-current protection
(AOCP), and thermal shutdown (TSD). Because these
various protection circuits are fully integrated in the IC
without external components, the reliability is improved
without increasing cost. Once a fault condition occurs,
switching is terminated and the SenseFET remains off.
This causes VCC to fall. When VCC reaches the UVLO
stop voltage, VSTOP (8V), the protection is reset and the
internal high-voltage current source charges the VCC
capacitor via the VSTR pin. When VCC reaches the UVLO
start voltage, VSTART (12V), the FPS resumes normal
operation. In this manner, the auto-restart can
alternately enable and disable the switching of the
power SenseFET until the fault condition is eliminated.
Figure 15. Frequency Fluctuation Waveform
© 2009 Fairchild Semiconductor Corporation
FSL136MR • Rev. 1.0.7
www.fairchildsemi.com
9
Figure 17. Auto-Restart Protection Waveforms
Overload Protection (OLP)
Overload is defined as the load current exceeding a
pre-set level due to an unexpected event. In this
situation, the protection circuit should be activated to
protect the SMPS. However, even when the SMPS is
operating normally, the overload protection (OLP) circuit
can be activated during the load transition or startup. To
avoid this undesired operation, the OLP circuit is
designed to be activated after a specified time to
determine whether it is a transient situation or a true
overload situation.
Figure 19. Abnormal Over-Current Protection
Thermal Shutdown (TSD)
The SenseFET and the control IC are integrated,
making it easier to detect the temperature of the
SenseFET.
When
the
temperature
exceeds
approximately 137°C, thermal shutdown is activated.
In conjunction with the IPK current limit pin (if used), the
current-mode feedback path limits the current in the
SenseFET when the maximum PWM duty cycle is
attained. If the output consumes more than this
maximum power, the output voltage (VO) decreases
below its rating voltage. This reduces the current
through the opto-coupler LED, which also reduces the
opto-coupler transistor current, thus increasing the
feedback voltage (VFB). If VFB exceeds 2.4V, the
feedback input diode is blocked and the 5µA current
source (IDELAY) slowly starts to charge CFB. In this
condition, VFB increases until it reaches 6V, when the
switching operation is terminated, as shown in Figure
18. The shutdown delay is the time required to charge
CFB from 2.4V to 6V with 5µA current source.
Figure 18.
Over-Voltage Protection (OVP)
In the event of a malfunction in the secondary-side
feedback circuit or an open feedback loop caused by a
soldering defect, the current through the opto-coupler
transistor becomes almost zero. Then, VFB climbs up in
a similar manner to the overload situation, forcing the
preset maximum current to be supplied to the SMPS
until the overload protection is activated. Because
excess energy is provided to the output, the output
voltage may exceed the rated voltage before the
overload protection is activated, resulting in the
breakdown of the devices in the secondary side. To
prevent this situation, an over-voltage protection (OVP)
circuit is employed. In general, VCC is proportional to the
output voltage and the FPS uses VCC instead of directly
monitoring the output voltage. If VCC exceeds 24V, OVP
circuit is activated, resulting in termination of the
switching operation. To avoid undesired activation of
OVP during normal operation, VCC should be designed
to be below 24V.
Output-Short Protection (OSP)
If the output is shorted, the steep current with extremely
high di/dt can flow through the SenseFET during the
LEB time. Such a steep current brings high-voltage
stress on the drain of SenseFET when turned off. To
protect the device from such an abnormal condition,
OSP detects VFB and SenseFET turn-on time. When the
VFB is higher than 1.6V and the SenseFET turn-on time
Overload Protection (OLP)
© 2009 Fairchild Semiconductor Corporation
FSL136MR • Rev. 1.0.7
FSL136MR — Green Mode Fairchild Power Switch (FPS™)
Abnormal Over-Current Protection (AOCP)
When the secondary rectifier diodes or the transformer
pin are shorted, a steep current with extremely high
di/dt can flow through the SenseFET during the LEB
time. Even though the FPS has OLP (Overload
Protection), it is not enough to protect the FPS in that
abnormal case, since severe current stress is imposed
on the SenseFET until OLP triggers. The FPS includes
the internal AOCP (Abnormal Over-Current Protection)
circuit shown in Figure 19. When the gate turn-on signal
is applied to the power SenseFET, the AOCP block is
enabled and monitors the current through the sensing
resistor. The voltage across the resistor is compared
with a preset AOCP level. If the sensing resistor voltage
is greater than the AOCP level, the set signal is applied
to the latch, resulting in the shutdown of the SMPS.
www.fairchildsemi.com
10
Figure 20.
Output Short Waveforms (OSP)
Soft-Start
The FPS has an internal soft-start circuit that slowly
increases the feedback voltage, together with the
SenseFET current, after it starts. The typical soft-start
time is 15ms, as shown in Figure 21, where progressive
increments of the SenseFET current are allowed during
the startup phase. The pulse width to the power
switching device is progressively increased to establish
the correct working conditions for transformers,
inductors, and capacitors. The voltage on the output
capacitors is progressively increased with the intention
of smoothly establishing the required output voltage.
Soft-start helps prevent transformer saturation and
reduce the stress on the secondary diode.
Figure 22. Burst-Mode Operation
Adjusting Peak Current Limit
As shown in Figure 23, a combined 6kΩ internal
resistance is connected to the non-inverting lead on the
PWM comparator. An external resistance of Rx on the
current limit pin forms a parallel resistance with the 6kΩ
when the internal diodes are biased by the main current
source of 400µA. For example, FSL136MR has a typical
SenseFET peak current limit (ILIM) of 2.15A. ILIM can be
adjusted to 1.5A by inserting Rx between the IPK pin and
the ground. The value of the Rx can be estimated by
the following equations:
2.15A: 1.5A = 6kΩ : XkΩ
(1)
X = Rx || 6kΩ
(2)
FSL136MR — Green Mode Fairchild Power Switch (FPS™)
is lower than 1.0µs, the FPS recognizes this condition
as an abnormal error and shuts down PWM switching
until VCC reaches VSTART again. An abnormal condition
output is shown in Figure 20.
where X is the resistance of the parallel network.
Figure 21.
Internal Soft-Start
Burst Operation
To minimize power dissipation in standby mode, the
FPS enters burst mode. As the load decreases, the
feedback voltage decreases. As shown in Figure 22,
the device automatically enters burst mode when the
feedback voltage drops below VBURH. Switching
continues until the feedback voltage drops below VBURL.
At this point, switching stops and the output voltages
drop at a rate dependent on standby current load. This
causes the feedback voltage to rise. Once it passes
VBURH, switching resumes. The feedback voltage then
falls and the process repeats. Burst mode alternately
enables and disables switching of the SenseFET and
reduces switching loss in standby mode.
© 2009 Fairchild Semiconductor Corporation
FSL136MR • Rev. 1.0.7
Figure 23. Peak Current Limit Adjustment
www.fairchildsemi.com
11
9.83
9.00
8
5
6.670
6.096
1
4
8.255
7.610
TOP VIEW
1.65
1.27
(0.56)
7.62
3.683
3.200
5.08 MAX
3.60
3.00
0.33 MIN
0.560
0.355
2.54
0.356
0.200
7.62
9.957
7.870
FRONT VIEW
SIDE VIEW
NOTES:
A. CONFORMS TO JEDEC MS-001, VARIATION BA
B. ALL DIMENSIONS ARE IN MILLIMETERS
C. DIMENSIONS ARE EXCLUSIVE OF BURRS,
MOLD FLASH, AND TIE BAR EXTRUSIONS
D. DIMENSIONS AND TOLERANCES PER ASME
Y14.5M-2009
E. DRAWING FILENAME: MKT-N08Frev3
15°
0°
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
© Semiconductor Components Industries, LLC
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
1
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
www.onsemi.com
工商网监
湘ICP备2023018690号
